Accessory Safety Information ......................153
MOTOROLA LIMITED WARRANTY............155
Patent and Trademark Information ..............158
v
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i857
Model Number: H65XAN6RR4AN
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a),
15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device
complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
vi
Note: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Getting St arted
camera
lens
volume
controls
Push-To-Talk
(PTT) button
audio jack
accessory
connector
retractable
anttena
mirror
speaker
(in back)
power button
light sensor
camera
key
microphone
1
Getting Started
pPower button.
Navigation key — press the arrows to scroll
through menus and lists.
OK Key — selects highlighted item; places
O
and answers calls.
Menu Key — accesses context-sensitive
m
menus.
Option Key — selects the option appearing
A
above it on the display.
sSend Key — places phone calls.
End Key — ends phone calls; returns to
e
idle screen.
2
tSpeakerphone Key — acts like s when
the flip is closed; turns speakerphone on;
used with voice names and voice records.
. Smart Key — acts like e when the flip is
closed; accesses recent calls; sends
incoming calls to voice mail.
Camera Key — accesses camera;
cc
captures picture.
To start using your i857 handset:
• Make sure your SIM card is in place.
• Charge the battery.
• Activate your service.
Battery
Battery
Removing the Battery Door
1 Make sure the handset is powered off. See
“Powering On and Off” on page 6.
2 Slide the release button back until it releases the
battery door.
release
button
3 Allow the battery door to pop, slide it forward and
remove it from the back of the handset.
Inserting the Battery
1 Remove the battery door.
2 Insert the top of the battery into the battery area.
Press the bottom of the battery down to secure it.
3
Getting Started
3 Replace the battey door and press it gently until
you hear a click.
Charging the Battery
Your handset comes with a battery charger.
1 Plug the charger into an electrical outlet.
2 Open the connector cover.
connector cover
4
3 Plug the other end of the charger into the
accessory connector.
Tip: To remove the charger from the accessory
connector: Press the buttons on the sides of
the plug. Pull the plug straight out.
4 When charging the battery for the first time, charge
for 30 minutes longer than the time shown in
“Charging Times” on page 5.
Battery
Charging Times
Check your battery and charger type against the grid
to determine the appropriate charging times.
BatteryCharger
RapidMid-Rate
High
Performance
Maximum
Capacity
For best results, charge the batteries within the
temperature range of 50°F to 104°F (10°C to 40°C).
Prolonged charging is not recommended.
2 hours 3 hours
3.5 hours7.5 hours
Removing the Battery
1 With the handset powered off, remove the battery
door.
2 Remove the battery by pushing it toward the
antenna and lifting it out.
Battery Use and Maintenance
• The Motorola Approved Lithium Ion chargers
provide optimum performance. Other chargers
may not fully charge the iDEN Lithium Ion battery
or may yield a reduced number of lifetime charge
cycles.
• Extreme temperatures degrade battery
performance. Do not store the battery where
temperatures exceed 140°F (60°C) or fall below
-4°F (-20°C).
• Lithium Ion batteries have a self discharge rate
and without use, lose about 1% of their charge per
day.
5
Getting Started
• The battery capacity is degraded if the battery is
stored for long periods while fully charged. If long
term storage is required, store at half capacity.
Activating your Mike Account
Before you can begin using your i857 handset, you
need to activate your Subscriber Identity Module
(SIM) card on The Mike Network. Your SIM card
holds the information required to enable your handset
to connect to The Mike Network. It also stores your
user information, language preference and contact
list entries.
• If you purchased your handset through an
Authorized Mike Network Dealer, your SIM should
already be active.
• If you purchased your handset at another location,
follow the “Getting Activated” instructions in the
Mike Services User’s Guide.
Powering On and Off
The first time you power your handset on, a screen
may appear asking you to update your browser
information. This means you must enable security.
To power your handset on:
1 Open the flip.
2 Press p.
6
Note: When powering on, if you press p for more
than 5 seconds, you will turn on Airplane
mode. See “Airplane Mode—Temporarily
Turning Off Calls” on page 135.
To power your handset off:
1 Open the flip.
2 Press and hold p.
If the Enter SIM PIN Code screen appears, enter
your SIM PIN. See “Entering the PIN” on page 11.
Press A under Ok.
Note: When you receive your handset, the SIM
PIN is 0000. Change your PIN to prevent
fraudulent use of the SIM card (see
“Changing the PIN” on page 12).
Finding Your Phone Number and Private ID
As your handset connects to the network, you will see
a welcome message and a connecting message.
When the idle screen appears, the handset is ready
to use.
TELUS
Finding Your Phone Number
and Private ID
My Info lets you view your phone number, Private ID,
and other handset information:
1 Press m to access the main menu.
2 Scroll to My Info.
3 Press O.
4 Scroll to see your information.
See “My Info” on page 81 for more information about
this feature.
Handset Basics
Any time your handset is powered on, the display
provides you with information and options.
The external display shows a shortened version of
the full-sized display. To see more information, open
the flip.
TELUS
The screen shown above is the idle screen. The idle
screen appears when your handset is on, but not
engaged in any activity.
status icons
text area
menu icon
display options
7
Getting Started
Text Area
This area displays menus, messages, names, phone
numbers, and other information.
Display Options
Two display options appear at the bottom of most
screens. You select a display option by pressing the
option key below it.
Menus and Lists
Your handset’s features are arranged in menus,
submenus, and lists.
To access the items in a menu or list, scroll using the
navigation key at the top of your keypad. This key lets
you scroll up, down, left, or right. Holding down the
appropriate part of the navigation key speeds up
scrolling.
In this guide, this symbol > tells you to select a menu
or list item. For example, Settings > Security
means:
1 Scroll to Settings on the main menu.
2 Press O to see the Settings screen.
3 Scroll to Security.
4 Press O to see the Security screen.
8
OK Key
Pressing O:
• Selects the highlighted menu item or list item
• Sets options
• Confirms actions
• Places and answer calls
Menu Key
Many of the handset’s features have menu options
that will change depending on the currently
highlighted menu option. These context-sensitvie
menus are available any time S appears. Press m to
access the menu.
Main Menu
All your handset’s features can be accessed through
the main menu. You can set the main menu to
appear as a list or as large icons (see “Large Dialing”
on page 92).
BrowserBrowse Mike’s Wireless
a
Java AppsJava applications on your
q
Web Services. See
page 83.
handset. See page 115.
Handset Basics
Settings Customize your handset.
b
Ring Tones Assign ring tones and turn
m
m CameraTake pictures. See
Media CenterAccess stored pictures and
c
m Mike’s Talk
Around
C VoiceRecordRecord and play audio
My InfoView personal handset
j
GPSFind your approximate
l
Contacts View, store, edit contacts.
d
See page 133.
ringer off. See page 105.
page 86.
audio recordings. See
page 94.
Launch/Exit Mike’s Talk
Around. Access Mike’s Talk
Around Setup and Help.
See page 24.
messages. See page 127.
information, including
phone number and Private
ID. See page 81.
geographical location. See
page 120.
See page 40.
MessagesAccess messages. See
e
Call ForwardSet call forwarding options.
f
Datebook Schedule appointments.
o
MemoStore a number to access
g
Call TimersHandset usage information.
h
Recent Calls Lists recent calls. See
i
ShortcutsCreate shortcuts to
s
Profiles Groups of setting you apply
p
Call Alert Lists call alerts. See
k
page 56.
See page 49.
See page 108.
later. See page 130.
See page 53.
page 35.
screens. See page 131.
together. See page 141.
page 20.
9
Getting Started
Status Icons
Status icons appear at the top of the display. Some
appear at all times. Others appear only when your
handset is engaged in certain activities or when you
have activated certain features.
b b c d
e
fgd
o p q r s
A
B
C
mMike’s Talk Around — Your
1 2
10
Battery Strength — More bars on
the battery indicate a greater
charge.
Signal Strength — More bars next
to the antenna indicate a stronger
signal.
Phone In Use — Your handset is
active on a phone call.
Private In Use — Your handset is
active on a Private call.
Talkgroup In Use — Your handset
is active on a group call.
handset is set to Mike’s Talk Around
mode.
Active Phone Line — 1 indicates
phone line 1 is ready to make calls;
2 indicates phone line 2 is ready to
make calls.
G J
H
K
I
L
Q R M
u
w x T
y
DE
c
U
Y Z
Call Forward — Your handset is set
to forward calls. See “Call
Forwarding” on page 49.
Ringer Off — Your handset is set to
not ring. See page 105.
Speaker Off — Sounds associated
with Private calls and group calls
are set to come through the
earpiece rather than through the
speaker.
Messages — You have one or
more messages. See “Message
Center” on page 56.
Internet — You are ready to browse
the internet.
Voice Record — You have one or
more voice records stored. See
page 127.
Airplane Mode — Your handset is
set to airplane mode.
Packet Data — You are ready to
transfer packet data or are
transferring packet data.
Locating Your SIM Card
Locating Your SIM Card
Your SIM (Subscriber Identity Module) card is a small
piece of plastic located in the SIM card holder in the
back of your handset, underneath the battery.
SIM card
If your SIM card is not in the SIM card holder, it may
be in the box your handset came in, attached to the
SIM carrier. If this is the case, carefully detach your
SIM card from the surrounding plastic and insert it as
described in “Inserting Your SIM Card” on page 14.
SIM Card Security
Your SIM card stores all your Contacts information.
Since this information is stored on your SIM card, not
in your handset, you can remove the information by
removing your SIM card.
Note: Except for making emergency calls, your
handset will not function without the SIM
card.
To prevent unauthorized use of your handset, your
SIM card can be protected by a PIN that you enter
each time the handset is powered on. You can
change the PIN or turn off the requirement that it be
entered.
Note: Your PIN is set to OFF by default.
Entering the PIN
You may be required to enter a SIM PIN when you
first use your handset.
When you receive your handset, the SIM PIN is 0000.
Change your PIN to prevent fraudulent use of the
SIM card.
11
Getting Started
Important: If you enter your PIN incorrectly 5 times,
your SIM card is blocked. To unblock your
SIM card, you must contact TELUS
Mobility Client Care. See “Unblocking the
PIN”.
1 When the Enter SIM PIN Code screen appears,
enter your SIM PIN. An asterisk appears for each
character entered.
2 Press A under Ok.
Changing the PIN
1 From the main menu, select Settings > Security >
Change Password > SIM PIN.
2 At the Enter Old SIM PIN screen, enter the current
SIM PIN.
3 Press A under Ok.
4 At the Enter New SIM PIN screen, enter the new
4- to 8-digit SIM PIN.
5 Press A under Ok.
6 At the Re-enter New SIM PIN screen, re-enter the
new SIM PIN to confirm.
7 Press A under Ok.
12
Turning the PIN Requirement On and
Off
When the SIM PIN requirement is on, you are
prompted to enter your PIN each time you turn on
your handset.
Note: If a SIM PI N is required, your handset will
not function until the SIM PIN is entered,
except for making emergency calls.
When the PIN requirement is off, your handset can
be used without entering a PIN.
Important: When the SIM PIN requirement is off, the
1 From the main menu, select Settings > Security >
SIM PIN.
personal data on your SIM card is not
protected. Anyone can use your handset
and access your personal data.
2 Select On or Off.
3 Enter the current SIM PIN.
4 Press A under Ok.
Unblocking the PIN
If you enter your PIN incorrectly 5 times, your SIM
card is blocked. To unblock your SIM card, you must
contact your TELUS Mobility Client Care to get a PIN
Unblock Key (PUK).
SIM Card Security
Important: If you unsuccessfully enter the PUK code
10 times, your SIM card is permanently
blocked and must be replaced. If this
happens, all data is lost. You will get a
message to contact TELUS Mobility Client
Care. Except for making emergency calls,
your handset will not function with a
blocked SIM card.
To unblock the PIN:
1 Press * # m 1.
2 At your TELUS Mobility representative’s request,
provide the information needed to give you a PUK
code.
3 Select Unblock PIN.
4 Enter the PUK code.
5 Enter a new 4- to 8-digit SIM PIN.
6 Re-enter your SIM PIN.
If you entered the codes properly, SIM Unlocked
appears on the display.
Inserting and Removing Your SIM Card
Important: Do not touch the gold-colored areas of
Switching SIM Cards
When you move your SIM card from one handset to
another, your Contacts information will not be erased
as the information is stored in the SIM. If you remove
your SIM card and use it with another handset, or use
another SIM card with your handset, the following
information is erased:
• The recent calls list
• Call forwarding settings
• Net alerts
• MMS messages
• Options set using the MMS Setup menu
• Pictures and audio recordings in the media center,
except those that are forward locked
• Information stored in Memo
• 3 most recent GPS Enabled locations
• Voice records
• Voice names
• Datebook events
• Options set using the Personalize menu
your SIM card.
13
Getting Started
Inserting Your SIM Card
1 With your handset powered off, remove the back
cover and battery.
2 Slide the latch towards the right to open the SIM
card holder.
latch
14
3 Open the SIM card holder.
4 Carefully slide your SIM card into the SIM card
holder.
SIM Card Security
5 Close the SIM card holder.
6 Slide the latch towards the left to close the SIM
card holder.
Removing Your SIM Card
Important: To avoid loss or damage, do not remove
1 With your handset powered off, remove the back
cover and battery. See “Removing the Battery” on
your SIM card from your handset unless
absolutely necessary.
page 5.
2 Slide the latch towards the right to open the SIM
card holder.
latch
3 Open the SIM card holder.
15
Getting Started
4 Carefully slide your SIM card out of the SIM card
holder.
5 Close the SIM card holder.
6 Slide the latch towards the left to close the SIM
card holder.
Note: Protect your SIM card as you would any
delicate object. Store it carefully.
Antenna
The retractable antenna on your i857 handset is
designed to be extended during calls.
16
To extend the antenna, pull gently on the rounded tip
until the antenna is fully extended and clicks into
position.
When finished with a call, retract the antenna by
pushing gently on the rounded tip until the antenna
clicks into place.
To optimize your handset’s performance, extend the
antenna when you make or receive a call, and avoid
touching the antenna with any body part.
Important: Failure to fully extend or retract the
antenna until the antenna clicks into place
causes severely degraded performance,
which may result in missed calls, dropped
calls, or garbled audio.
Accessories
Your handset comes with a battery and a charger.
To order additional accessories, log on to our Web
site at www.telusmobility.com or contact your Mike
Dealer.
For More Information
If you have questions about your i857i857 handset,
contact your Mike Dealer or TELUS Mobility Client
Care.
Accessories
17
Mike’s Direct Connect
Service
There are two ways of communicating over Mike’s
Direct Connect service:
• one-to-one using a private call
• one-to-many in a group call
Both of these methods are very similar to two-way
radio, and at a fraction of the cost of traditional
cellular. Mike’s Direct Connect also offers the Call
Alert feature, which gives recipients a notice, similar
to a ringer, that you would like to speak to them.
One-to-One Private Calls
Making Private Calls
1 If the flip is open, enter the Private ID you want to
call. -or-
If the flip is closed, select the number as you would
when making a phone call.
2 Press and hold the PTT button on the side of your
handset. Begin talking after your handset emits a
chirping sound.
3 Release the PTT button to listen.
Tip:To let someone know that you want to talk to
him or her on a Private call, send a call alert.
See “Call Alerts” on page 20.
Every Private ID number contains 3 parts — an area
ID, a fleet ID, and a member ID — with asterisks
between each of these parts. For example:
999*999*9999.
When you place a Private call, you must enter the
entire Private ID number including the asterisks.
When you store a Private ID number in Contacts,
include the asterisks with the entire Private ID
number in case you travel with your handset, or
another Private ID user, outside of your network.
From the Keypad
To enter the Private ID you want to call, press the
numbers on the keypad.
If you make a mistake:
• To clear a digit, press A under Delete.
• To clear all digits, press and hold A under Delete.
• To insert or delete a digit anywhere in the string of
digits you have entered, scroll left or right.
• To cancel, press e.
18
From the Recent Calls List
The recent calls list stores the last 20 calls you made
or received.
To select a Private ID from the recent calls list as the
number you want to call:
1 From the idle screen, scroll down. -or-
From the main menu, select Recent Calls.
2 Scroll to the name or Private ID number you want
to call.
From Contacts
If you have Private IDs stored in Contacts, you can
use these numbers to make calls. For information on
entering numbers into Contacts, see “Creating
Entries” on page 41.
Calling from the Contacts List
1 From the main menu, select Contacts.
2 Scroll to the name or Private ID number you want
to call.
Tip: T o find Contact s entries faster , use the keypad
to enter the first letter of the name.
3 Place the call now. -or-
With the Contacts type field highlighted, scroll left
or right to display the Contacts type for the number
you want to call.
If you are making a Private call, your handset places
the call to the Private ID stored in the Contacts entry,
even if the Private ID icon is not displayed.
Calling from a Contacts Entry
1 From the main menu, select Contacts.
2 Scroll to the name or Private ID number you want
to call.
3 Press A under View. -or-
If View is not one of your options: Press m. Select
View.
4 Place the call now. -or-
Scroll to view more numbers. When you place the
call, it is made to the number displayed.
Receiving Private Calls
When you receive a Private call, your handset emits
a chirping sound or vibrates.
To answer a Private call:
1 Wait for the caller to finish speaking.
2 Press and hold the PTT button on the side of your
handset. Begin talking after your handset emits a
chirping sound.
19
Mike’s Direct Connect Service
3 Release the PTT button to listen.
One Touch PTT
One Touch PTT sets your handset to call the most
recent Private ID on the recent calls list, or to a
Private ID you choose, every time you press the PTT
button. See “Setting One Touch PTT” below.
Setting One Touch PTT
One Touch PTT sets your handset to call the most
recent Private ID on the recent calls list, or to a
Private ID you choose, every time you press the PTT
button.
To set your handset to call the most recent Private ID
on the recent calls list:
1 From the main menu, select Settings > 2-Way
Radio > One Touch PTT.
2 Scroll to Last Call.
3 Press A under Select.
To set your handset to call a Private ID you choose:
1 From the main menu, select Settings > 2-Way
Radio > One Touch PTT.
2 Scroll to Assign Number.
3 Press A under Change.
4 To enter the number you want your handset to call
every time you press the PTT button:
20
Enter the number using your keypad. -or-
Press A under Search. Select Contacts, Recent
Calls, or Memo. Enter the number from Contacts,
the recent calls list, or Memo, as you would when
making a call.
Tip: If you are entering a Talkgroup number, enter
# before the number.
5 Press A under Ok.
To turn off One Touch PTT:
1 From the main menu, select Settings > 2-Way
Radio > One Touch PTT.
2 Scroll to Off.
3 Press A under Select.
Call Alerts
Sending a call alert lets the recipient know that you
want to talk to him or her on a Private call.
When you send a call alert, the recipient’s handset
emits a series of beeps and displays your name or
Private ID.
The recipient can:
• Answer — begin a Private call with the sender
• Queue — store the call alert to the call alert queue,
which is a list of call alerts
Using the Call Alert Queue
• Clear — dismiss and delete the call alert
Sending Call Alerts
1 Enter the Private ID you want to send to, as you
would when making a Private call.
2 Press A under Alert. Ready to Alert appears on
the display.
3 Press the PTT button until Alert Successful
appears on the display.
Receiving Call Alerts
When you receive a call alert, you must answer,
queue, or clear it. You cannot receive phone calls or
Private calls until you do.
To answer a call alert, press the PTT button to
make a Private call to the sender.
To queue a call alert, press A under Queue.
To clear a call alert, press A under Clear.
Using the Call Alert Queue
When you queue a call alert, it remains in the call
alert queue until you respond to it, or delete it.
Viewing Call Alerts
1 From the main menu, select Call Alert.
2 Scroll through the list.
Viewing Date and Time
To view the date and time a call alert was received:
1 From the main menu, select Call Alert.
2 Scroll to the call alert you want information on.
3 Press m.
4 Select View.
Responding to Call Alerts in the Queue
After you queue a call alert, you can respond to it by
making a Private call to the sender or sending a call
alert to the sender. This call alert is then removed
from the queue.
Making a Private Call to the Sender
1 From the main menu, select Call Alert.
2 Scroll to the call alert you want to respond to.
3 Press the PTT button to begin the call.
Sending a Call Alert to the Sender
1 From the main menu, select Call Alert.
2 Scroll to the call alert you want to respond to.
3 Press A under Alert. Ready to Alert appears on
the display.
4 Press and hold the PTT button until Alert
Successful appears on the display.
21
Mike’s Direct Connect Service
Note: Answering a call alert from the recent call list
does not remove it from the call alert queue.
Deleting Call Alerts
To delete a call alert from the queue:
1 From the call alert queue, scroll to the call alert you
want to delete.
2 Press m.
3 Select Delete.
4 Press A under Yes to confirm.
To delete all call alerts from the queue:
1 From the call alert queue, press m.
2 From the call alert menu, select Delete All.
3 Press A under Yes to confirm.
Sorting Call Alerts
To sort call alerts by the order they were received:
1 From the main menu, select Call Alert.
2 Press m.
3 Select Sort By.
4 Scroll to First on Top or Last on Top.
5 Press A under Select.
22
One-to-Many Group Calls
A group call is a type of dispatch call made to all
members of a Talkgroup at once. A Talkgroup is a
group of Private IDs.
To receive group calls made to a Talkgroup, you
must join the Talkgroup. See “Joining a Talkgroup”.
Joining a Talkgroup
Your Mike sales representative creates Talkgroups
for you and assigns each Talkgroup to a Talkgroup
number. You can choose a name for each of your
Talkgroups when you create entries for them in
Contacts.
To receive group calls made to a Talkgroup, you
must join the Talkgroup. You can belong to only one
Talkgroup at a time. When you join a new Talkgroup,
you no longer belong to your previous Talkgroup.
To join a Talkgroup:
1 Press #. Then enter the Talkgroup number using
the keypad. -or-
Choose the Talkgroup name from Contacts or
recent calls list.
2 Press A under Join.
Making Group Calls
1 Press #. Then enter the Talkgroup number using
the keypad. -or-
Choose the Talkgroup name from Contacts or
recent calls list.
2 Proceed as if making a Private call.
Receiving Group Calls
To answer a group call:
Proceed as if answering a Private call. Only one
person at a time may speak on a group call.
Turning off Group Calls
To control whether you hear group calls to your
Talkgroup:
1 From the main menu, select Settings > 2-Way
Radio > Tkgrp Silent.
2 Press A under Change.
3 Scroll to On if you do not want to hear group calls
to your Talkgroup. -or-
Scroll to Off if you want to hear group calls to your
Talkgroup.
4 Press A under Select.
One-to-Many Group Calls
23
Loading...
+ 142 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.