VII. GOVERNING LAW:.................................. 193
VIII. For Australia Only.................................... 193
178
10
Declaration of Conformity
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
Declaration of Conformity
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Motorola Solutions, Inc.
Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.
Phone Number: 1-800-927-2744
Hereby declares that the product:
Model Name: APX 8000H
conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a)
English
Class B Digital Device
11
English
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. This device complies with
Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules and Industry Canada license-exempt RSS standard. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
•
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio or TV technician for help.
12
English
Important Safety Information
RF Energy Exposure and Product Safety
Guide for Portable Two-Way Radios
ATTENTION!
This radio is restricted to Occupational use only. Before
using the radio, read the RF Energy Exposure and Product
Safety Guide for Portable Two-Way Radios which contains
important operating instructions for safe usage and RF
energy awareness and control for Compliance with
applicable standards and Regulations.
For a list of Motorola Solutions-approved antennas,
batteries, and other accessories, visit the following website:
http://www.motorolasolutions.com
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is
not more than that necessary for successful
communication.
This radio transmitter has been approved by Industry
Canada to operate with Motorola Solutions-approved
antenna with the maximum permissible gain and required
antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
13
English
Notice to Users (FCC and
Industry Canada)
This device complies with Part 15 of the FCC rules and
Industry Canada's license-exempt RSS's per the following
conditions:
•This device may not cause harmful interference.
This device must accept any interference received,
•
including interference that may cause undesired
operation.
•Changes or modifications made to this device, not
expressly approved by Motorola Solutions, could void
the authority of the user to operate this equipment.
14
Software Version
All the features described in the following sections are
supported by the software version R18.00.00 or later.
See Accessing the Radio Information
determine the software version of your radio.
Check with your dealer or system administrator for more
details of all the features supported.
on page 172 to
English
15
English
Computer Software
Copyrights
The Motorola Solutions products described in this manual
may include copyrighted Motorola Solutions computer
programs stored in semiconductor memories or other
media. Laws in the United States and other countries
preserve for Motorola Solutions certain exclusive rights for
copyrighted computer programs including, but not limited
to, the exclusive right to copy or reproduce in any form the
copyrighted computer program. Accordingly, any
copyrighted Motorola Solutions computer programs
contained in the Motorola Solutions products described in
this manual may not be copied, reproduced, modified,
reverse-engineered, or distributed in any manner without
the express written permission of Motorola Solutions.
Furthermore, the purchase of Motorola Solutions products
shall not be deemed to grant either directly or by
implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Motorola
Solutions, except for the normal non-exclusive license to
use that arises by operation of law in the sale of a product.
16
Documentation Copyrights
No duplication or distribution of this document or any
portion thereof shall take place without the express written
permission of Motorola Solutions. No part of this manual
may be reproduced, distributed, or transmitted in any form
or by any means, electronic or mechanical, for any purpose
without the express written permission of Motorola
Solutions.
English
17
English
Disclaimer
The information in this document is carefully examined, and
is believed to be entirely reliable. However, no
responsibility is assumed for inaccuracies. Furthermore,
Motorola Solutions reserves the right to make changes to
any products herein to improve readability, function, or
design. Motorola Solutions does not assume any liability
arising out of the applications or use of any product or
circuit described herein; nor does it cover any license under
its patent rights, nor the rights of others.
18
English
Getting Started
How to Use This Guide
This User Guide covers the basic operation of the APX
Portables
However, your dealer or system administrator may have
customized your radio for your specific needs. Check with
your dealer or system administrator for more information.
Notations Used in This Manual
Throughout the text in this publication, you will notice the
use of Warning, Caution, and Notice. These notations are
used to emphasize that safety hazards exist, and the care
that must be taken or observed.
.
WARNING:
An operational procedure, practice, or condition and
so on, which may result in injury or death if not
carefully observed.
CAUTION:
An operational procedure, practice, or condition and
so on, which may result in damage to the equipment
if not carefully observed.
NOTICE:
An operational procedure, practice, or condition and
so on, which is essential to emphasize.
The following special notations identify certain items.
ExampleDescription
Home button
or
Phon
Buttons and keys are shown in bold
print or as an icon.
Menu entries are shown similar to
the way they appear on the display
of the radio.
This means “Press the right side of
the 4-Way Navigation Button”.
Radio Care
Proper radio usage and care assures efficient operation
and long life for the product.
The following are recommendations and warnings when
using the radio
19
A
English
CAUTION:
•Your radio has a vent port that allows for
pressure equalization in the radio. Never poke
this vent with any objects, such as fingernails,
needles, tweezers, or screwdrivers. This could
create leak paths into the radio and the radio’s
submergibility will be lost.
•Your radio is designed to be submerged to a
maximum depth of 2 meters, with a maximum
submersion time of 4 hours. Exceeding either
maximum limit may result in damage to the
radio.
•Elastomer seals used in portable radios can age
with time and environmental exposure.
Therefore, Motorola Solutions recommends that
radios be checked annually as a preventive
measure in order to assure the waterseal
integrity of the radio. Motorola Solutions details
the disassembly, test, and reassembly
procedures along with necessary test equipment
in the radio service manual.
If the radio battery contact recess is exposed to
•
water without the battery attached, dry and clean
the radio battery contacts before attaching a
battery to the radio. Turn the radio over with the
battery contact recess facing down and shake
the radio so any trapped water can escape. The
battery contacts must be dry before attaching a
battery or a short circuit of the contacts could
occur.
•If the radio side accessory connector contacts
are exposed to water without an accessory or
accessory connector cover attached, clean and
dry this area to prevent foreign material build up
20
English
or contact corrosion. These can prevent reliable
accessory interconnect to the radio.
•Accessory connector cover must be attached to
the radio side accessory connector if an
accessory is not attached to the radio.
If the radio is submerged or exposed to a high
•
force water spray, such as from a hose, remove
the side accessory connector or accessory
connector cover immediately and check to make
sure no water was forced into the accessory
connector/radio interface. Rinse and dry the area
and re-attach the accessory or accessory
connector cover if leakage occurs.
•If the radio is exposed to a corrosive
environment, such as salt water or corrosive
gases or liquids, rinse and clean the radio
immediately to prevent damage to radio
materials, especially plated surfaces. Refer to
Cleaning Your Radio on page 21 for detailed
instructions. Remove the battery and the
antenna before cleaning if exposed to corrosive
environments.
•If the radio has been submerged in water, shake
the radio well so that any water that may be
trapped inside the speaker grille and microphone
port can be removed. Otherwise, the water will
decrease the audio quality of the radio.
•Do not disassemble the radio. This could
damage radio seals and result in leak paths into
the radio. Any radio maintenance should be
performed only by a qualified radio technician.
•Underwriter Laboratory (UL) certified radios
should only be opened and serviced by UL
approved service centers. Opening or repairing
at unauthorized locations will invalidate the
radio’s hazardous location rating.
•Do not pound, drop, or throw the radio
unnecessarily.
•When charging the radio using a wall mounted
charger, the radio must be turned off. Otherwise,
the Man Down Alert and Emergency may be
accidentally triggered.
Cleaning Your Radio
CAUTION:
Do not use solvents or disinfectants to clean your
radio as these chemicals may permanently damage
the radio housing, seals, and adhesives.
21
English
To clean the external surfaces of your radio, follow the
procedure described next.
1 Combine one teaspoon of mild dishwashing
detergent to one gallon of water (0.5% solution).
2 Apply the solution sparingly with a stiff, non-metallic,
shortbristled brush, making sure that excess
detergent does not get entrapped near the
connectors, controls, or crevices. Rinse and then dry
the radio thoroughly with a soft, lint-free cloth.
3 Clean battery contacts with a lint-free cloth to
remove dirt or grease.
Radio Service and Repair
Proper repair and maintenance procedures will assure
efficient operation and long life for this product. A Motorola
Solutions maintenance agreement will provide expert
service to keep this and all other communication equipment
in perfect operating condition.
A nationwide service organization is provided by Motorola
Solutions to support maintenance services. Through its
maintenance and installation program, Motorola Solutions
makes available the finest service to those desiring reliable,
continuous communications on a contract basis.
For a contract service agreement, please contact your
nearest Motorola Solutions service or sales representative,
or an authorized Motorola Solutions dealer.
Additional Performance
Enhancement
The following performance enhancements are some of the
latest creations designed to enhance the security, quality,
and efficiency of the radios.
ASTRO 25 Enhanced Data
ASTRO 25 Enhanced Data is optimized to handle different
message sizes and variable update rates from different
applications of the radio. Add Enhanced Data to the
Integrated Data system with a software installation to
improve data channel efficiency and enable denser network
traffic.
22
English
Dynamic System Resilience (DSR)
DSR ensures the radio system is seamlessly switched to a
backup master site dynamically in case of system failure.
DSR also provides additional indication such as failure
detection, fault recovery, and redundancy within the system
to address to the user in need. Mechanisms related to the
Integrated Voice and Data (IV&D) or data centric are all
supported by DSR.
CrossTalk Prevention
This feature prevents crosstalk scenarios from happening,
especially when a wideband antenna is used. This feature
allows the adjustment of the internal SSI clock rate of the
radio. This subsequently reduces the possibility of radio
frequency interfering spurs and prevents the issues of
crosstalk.
Encrypted Integrated Data (EID)
EID provides security encryption and authentication of
IV&D data bearer service communication between the
radio and the Customer Enterprise Network.
SecureNet
SecureNet allows user to perform secured communications
on an Analog or Motorola Data Communication (MDC)
channel. The MDC Over-the-Air Rekeying (OTAR) feature
will allow users to perform OTAR activities on an MDC
channel.
P25 Digital Vehicular Repeater System
(DVRS)
Motorola Solutions offers an MSI Certified APX compatible,
3rd Party, P25 Digital Vehicular Repeater System (DVRS)
that provides low cost portable radio coverage in areas
where only mobile radio coverage is available and portable
radio coverage is either intermittent or non-existent.
Conventional Talkgroup and Radio
Scan Enhancements
A few enhancements have been made to the Conventional
Talkgroup at the system. These enhancements improve the
Scan feature operation significantly when multiple agencies
are using a single conventional radio frequency channel.
These enhancements allow users to use Selective Squelch
to operate on only the subset of talkgroups that are
23
English
relevant to the users rather than all talkgroups on the
channel. These Scan improvements have been made to
eliminate the audio holes that were present and to turn on
the busy LED when activity is present on the channel.
Mixed Vote Scan and Standard Conventional Scan
configurations are supported. Priority Operation is also
supported.
Up to 30 different talkgroups can be supported using
conventional channels. A maximum of four talkgroups can
be supported when Vote Scan channels are being used.
Smart PTT is supported with this enhancement as Smart
PTT prevents users from transmitting while other users are
on the channel.
NOTICE:
User Selectable Talkgroups are not compatible with
this Conventional Talkgroup Enhancement.
What Your Dealer/System
Administrator Can Tell You
Check with your dealer or system administrator for the
correct radio settings, if the radio is to be operated in
extreme temperatures (less than -30 °C or more than +60
°C).
You can consult your dealer or system administrator about
the following:
•Is your radio programmed with any preset conventional
channels?
Which buttons have been programmed to access other
•
features?
•What optional accessories may suit your needs?
NOTICE:
Specifications may vary for different radio models.
Check with your dealer or system administrator for
more information.
24
English
Preparing Your Radio for
Use
This section provides simple instructions to prepare your
radio for use.
Charging the Battery
WARNING:
To avoid a possible explosion:
not replace the battery in any area labeled
•Do
hazardous atmosphere.
•Do not discard batteries in a fire.
The Motorola Solutions-approved battery shipped with your
radio is uncharged. Prior to using a new battery, charge it
for a minimum of 16 hours to ensure optimum capacity and
performance. For a list of Motorola Solutions-authorized
batteries and chargers available for use with your radio,
see Accessories on page 177.
NOTICE:
When charging a battery attached to a radio, the
radio must be turned off.
To charge the battery, place the battery (with or
without the radio) in a Motorola Solutions-approved
charger.
The LED on the charger indicates the charging
progress; see the Charger User Guide.
Attaching the Battery
If your radio is preprogrammed with volatile-key retention,
the encryption keys are retained for approximately 30
seconds after battery removal. Check with your dealer or
system administrator for more information.
You can view the status of the battery if the radio is using
an IMPRES battery. See IMPRES Battery Annunciator on
page 171 for more information.
25
English
NOTICE:
User is notified if radio detects non-Motorola
Solutions battery upon powering up, charging, or
removing from the charger. This feature is
applicable for IMPRES and Non-IMPRES battery.
When the radio is attached with the non-Motorola
Solutions battery, a tone sounds, display shows
Unknown Battery temporarily, and battery indicator
is not shown in the radio display. Battery menu
screen displays Unknown Battery permanently and
IMPRES battery information is not shown on the
radio display.
1 Slide the battery into the radio frame until the side
latches click into place.
2 To remove the battery, turn the radio off. Squeeze
the release latches at the bottom of the battery
until the battery releases from the radio and remove
the battery from the radio.
26
A
Attaching the Antenna
Ensure the radio is turned off before attaching the antenna.
1 Set the antenna in the receptacle.
English
3 To remove the antenna, turn the antenna
counterclockwise.
NOTICE:
When removing the antenna, ensure that the
radio is turned off.
2 Turn the antenna clockwise to attach to the radio.
27
C
B
A
English
Removing and Attaching the
Accessory Connector Cover
The accessory connector is on the antenna side of the
radio. It is used to connect accessories to the radio.
NOTICE:
To prevent damage to the connector, shield it with
the connector cover when not in use.
1 To remove the accessory connector cover, rotate the
thumbscrew counterclockwise until it disengages
from the radio.
NOTICE:
If the thumbscrew is too tight, use an Allen
wrench at to loosen it first.
2 Rotate and lift the connector cover to disengage it
from the radio.
3 To attach the accessory connector cover, insert the
hooked end of the cover into the slot above the
connector.
4 Press the top of the cover downward to seat it in the
slot.
28
5
Once in place, tighten by rotating the thumbscrew
clockwise by hand.
Using the Carry Holder
1 Position the radio within the carry holder with the
main speaker facing outward.
English
3 To remove the radio from the carry holder, place the
tip of your fingers on the ledge of the carry holder.
2 Slide the radio down into the carry holder until it
clicks in place.
29
English
4 Push at the bottom of the radio until the radio is
released from it.
Turning On the Radio
1 Rotate the On/Off/Volume Control Knob clockwise
until you hear a click.
30
Loading...
+ 164 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.