Motorola AP 6522M Installation Manual

AP 6522M Access Point

INSTALLATION GUIDE

2 AP 6522M Access Point

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered
trademark of Symbol Technologies, Inc., a Zebra Technologies company.

© 2015 Symbol Technologies, Inc

.

Installation Guide 3

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.0 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3 Access Point Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Wall Mount Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.1 Wall Mount Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.2 Wall Mount Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.5 Suspended Ceiling T-Bar Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.5.1 Suspended Ceiling T-Bar Mount Procedure. . . . . . . . . . . . . . . . . . . . . . . . 12

2.6 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.0 Initial Access Point Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.1 AP 6522M Integrated Antenna Model Electrical Characteristics . . . . . . . . . . . . . 25

4.2 AP 6522M Integrated Antenna Model Physical Characteristics . . . . . . . . . . . . . . 25

4.3 Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.1 Wireless Device Country Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.1.1 Country Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.1.2 Frequency of Operation - FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.1.2 Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.2 Health and Safety Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.2.1 Warnings for Use of Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.1.2 Potentially Hazardous Atmospheres - Fixed Installations . . . . . . . . . . . . . 28

4 AP 6522M Access Point

5.1.3 Safety in Hospitals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.3 RF Exposure Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.3.1Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.4 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.5 RF Radio Frequency Requirements - FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.5.1 Radio Transmitters (Part 15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.1.2 Radio Frequency Interference Requirements - Canada . . . . . . . . . . . . . . . 31

5.6 RF CE Marking and European Economic Area (EEA) . . . . . . . . . . . . . . . . . . . . . . . . 32

5.6.1 Statement of Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.7 RF Waste electrical and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . 33

5.7.1 Turkish WEEE Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.8 Other Countries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

6.0 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

7.0 Symbol Technologies End-User Software License Agreement . . . . . . . . . 38

Installation Guide 5

!

1 Introduction

The AP 6522M Access Point, a component of the wireless controller system, links wireless 802.11abgn devices to
the controller, enabling the growth of your wireless network with a cost effective alternative to standard Access
Points. The AP 6522M Access Point provides multiple deployment options.

The AP 6522M Access Point receives all power and transfers data through the same CAT-5 or better Ethernet
cable. An 802.3af Ethernet switch or power supply (specifically rated for the AP 6522M) is required (Part No.
PWRS-14000-148R).

An AP 6522M model Access Point uses WiNG software as its onboard operating system. The Access Point’s
unique WiNG 5 software enables the Access Point to function as either a Virtual Controller AP capable of
adopting and managing up to 24 additional AP 6522M Access Points, a Standalone Access Point, or a Dependent
mode Access Point managed by its connected controller.

The AP 6522M Access Point is approved under MODEL: AP-0622.

This document is written for the qualified network device installer.

1.1 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or

equipment malfunction.

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment damage.

6 AP 6522M Access Point

1.2 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment installation before
connecting the Access Point.

• Remove jewelry and watches before installing this equipment.

• Verify the unit is grounded before connecting it to the power source.

• Verify any device connected to this unit is properly wired and grounded.

• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment
operation specifications.

1.3 Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment placement, power

drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.

1.4 Package Contents

An AP 6522M Access Point ships with the following:

• AP 6522M Access Point with internal antennas

• AP 6522M Access Point Installation Guide (This Guide)

Installation Guide 7

1.4.1 Features

• 2 RJ-45 connectors, one for 10/100/1000 Ethernet and the other for the serial/console connector

• LED indicators

• Slots for wall mounting

• Clips for mounting on a suspended ceiling T-bar (internal antenna model only) with separately orderable

accessories

The AP 6522M Access Point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and accepts

802.3af-compliant power from an external source. The illustration below is of an integrated antenna model.

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

The AP 6522M Access Point comes with dual radios supporting 802.11abgn. The Access Point contains runtime
firmware which enables the unit to boot after a power up. The runtime firmware on the Access Point and the
firmware downloaded from the connected controller can be updated via the Ethernet interface.

8 AP 6522M Access Point

2 Hardware Installation

2.1 Installation Instructions

The AP 6522M Access Point mounts either on a wall (with customer supplied M4 x 25 pan head screws and wall
anchor - or equivalent) or on a suspended ceiling T-bar. An AP 6522M is not designed for mounting on a desk.

To prepare for the installation:

1. Match the model number on the purchase order with the model numbers in the packing list and on the
case of the Access Point.

2. Verify the contents of the box include the intended AP 6522M Access Point, and the included hardware
matches the package contents on page 5.

Part Number Description

AP-6522M-66030-WR

NOTE

3. Review site survey and network analysis reports to determine the location and mounting position for the
Access Point.

4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3af power source and run the cable to the
installation site. Ensure there is sufficient slack on the cable to perform the installation steps.

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

In the above part numbers, a country code of “WR” represents a world
wide model, whereas “US” defines the model as only legally deployable
in the United States.

is recommended for Gigabit operation.

Dual 802.11n radio AP 6522M. Plastic enclosure with internal antennas.
For use in Japan only.

Installation Guide 9

2.2 Precautions

Before installing an AP 6522M model Access Point, verify the following:

• If a DC power supply is used, ensure it’s the approved power supply for the AP 6522M
(PWRS-14000-148R).

• It is recommended you do not to install the AP 6522M in wet or dusty areas.

• Verify the environment has a continuous temperature range between 0° C to 40° C.

2.3 Access Point Placement

For optimal performance, install the Access Point away from transformers, heavy-duty motors, fluorescent lights,
microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls
or floors block transmission. Install the Access Point in an open area or add Access Points as needed to improve
coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An
area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even
placement of a light bulb) provides even, efficient coverage.

Place the Access Point using the following guidelines:

• Install the Access Point at an ideal height of 10 feet from the ground.

• Orient the Access Point for optimal performance.

To maximize the Access Point’s radio coverage area, it is recommended to conduct a site survey to define and
document radio interference obstacles before installing the Access Point.

2.4 Wall Mount Instructions

Wall mounting requires hanging the AP 6522M along its width or length using the two slots on the bottom of the
unit. The AP 6522M can be mounted on to any plaster, wood, or cement wall surface using customer supplied screw
hardware (M3.5 x 0.6 x 20 mm- or equivalent).

2.4.1 Wall Mount Hardware

• Two wide-shoulder Phillips pan head self-tapping screws (customer supplied)

• Two wall anchors (customer supplied)

NOTE The following screws are recommended: (ANSI Standard) #6-18 X

0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard Metric)
M3.5 X 0.6 X 20mm Type D Self-Tapping Screw.

10 AP 6522M Access Point

!

2.4.2 Wall Mount Procedure

1. Orient the case on the wall by its width or length.

CAUTION To ensure proper operation of an AP 6522M Access Point, ensure it is

mounted in the correct orientation for the desired cable routing.

2. Mark two points (for drill holes) 4.08 inches (103.7 mm) apart on a horizontal or vertical line depending on
the desired cable exit direction. If mounted on a horizontal line, the cables will exit to the left or right. If
mounted on a vertical line, the cables will exit up or down.

3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall mounting screw and
stop when there is 1mm between the screw head and the wall.

NOTE When pre-drilling a hole the recommended hole size is 2.8mm (0.11in.).

4. Attach an Ethernet cable from the Access Point to a controller with an 802.3af-compatible power source
or use the PWRS-14000-148R power supply to supply power to the AP 6522M (once fully cabled).

Installation Guide 11

!

5. Place the middle of each of the case’s mount slots over the screw heads.

6. Slide the case down along the mounting surface to hang the mount slots on the screw heads.

7. Verify the unit has power by observing that the LEDs are lit or flashing.

CAUTION If not using a 802.3af capable controller to power the AP 6522M,

ensure only the AP 6522M’s designated power supply
(PWRS-14000-148R) is used to supply power to the Access Point.
Using an incorrectly rated power supply could damage the unit and
void the product warranty. Do not actually connect to the power
source until the cabling portion of the installation is complete.

12 AP 6522M Access Point

2.5 Suspended Ceiling T-Bar Mount

Ceiling mount requires holding the AP 6522M Access Point up against a T-bar of a suspended ceiling grid and
twisting the case onto the T-bar.

2.5.1 Suspended Ceiling T-Bar Mount Procedure

1. Attach an Ethernet cable from the Access Point to a controller with an 802.3af compatible power source
or use the PWRS-14000-148R power supply to supply power to the AP 6522M (once fully cabled).

2. Align the bottom of the T-bar with the back of the case.

3. Orient the case by its length, and the length of the T-bar.

4. Rotate the case 45 degrees clockwise, or to about 10 o’clock.

5. Push the back of the case onto the bottom of the T-bar.

6. Rotate the case 45 degrees counter-clockwise. The clips click as they fasten to the T-bar.

7. Verify the unit has power by observing the LEDs.

Installation Guide 13

!

CAUTION If not using a 802.3af capable controller to power the AP 6522M,

ensure only the AP 6522M’s designated power supply
(PWRS-14000-148R) is used to supply power to the Access Point.
Using an incorrectly rated power supply could damage the unit and
void the product warranty. Do not actually connect to the power
source until the cabling portion of the installation is complete.

2.6 LED Indicators

AP 6522M Access Points have LED activity indicators on the side of the case.

The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz

802.11an (amber) radio or the 2.4 GHz 802.11bgn (green) radio.

Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green)

Unadopted Off Blink interval at 5 times a second

Normal
Operation

Firmware
Update

Sensor Mode Blink interval at 5 times a second Blink interval at 5 times a second

• If this radio band is enabled:
Blink at 5 second interval

• If this radio band is disabled:
Off

• If there is activity on this band:
Blink interval at 1 time per second

On Off

• If this radio band is enabled:
Blink at 5 second interval

• If this radio band is disabled:
Off

• If there is activity on this band:
Blink interval at 1 time per second

14 AP 6522M Access Point

3 Initial Access Point Configuration

Once the Access Point is installed and powered on, complete the following steps to get the device up and running
using the Initial Setup Wizard:

1. Attach an Ethernet cable from the Access Point to a controller with an 802.3af compatible power source
or use the PWRS-14000-148R power supply to supply power to the AP 6522M (once fully cabled).

If your host system is a DHCP server, an IP address is automatically assigned to the Access Point and can
be used for device connection. However, if a DHCP server is not available, you’ll need to derive the IP
address from the Access Point MAC address. Using this method, the last two bytes of the Access Point
MAC address become the last two octets of the IP address.

AP 6522M MAC address - 00:C0:23:00:F0:0A
AP 6522M IP address equivalent - 169.254.240.10

To derive the Access Point’s IP address using its factory assigned MAC address:

a. Open the Windows calculator be selecting Start > All Programs > Accessories > Calculator. This menu

path may vary slightly depending on your version of Windows.

b. With the Calculator displayed, select View > Scientific. Select the Hex radio button.

c. Enter a hex byte of the AP 6522M’s MAC address. For example, F0.

d. Select the Dec radio button. The calculator converts F0 into 240. Repeat this process for the last

AP 6522M MAC address octet.

2. Point the Web browser to the Access Point’s IP address. The following login screen displays:

3. Enter the default username admin in the Username field.

4. Enter the default password admin123 in the Password field.

Installation Guide 15

5. Click the Login button to load the management interface.

NOTE When logging in for the first time, you’re prompted to change the

password to enhance device security in subsequent logins.

NOTE If you get disconnected when running the wizard, you can connect again

with the Access Point’s actual IP address (once obtained) and resume the
wizard.

6. If this is the first time the management interface has been accessed, the Initial Setup Wizard
automatically displays.

The Introduction screen displays the various actions that can be performed using the wizard under the
Function Highlight field.

16 AP 6522M Access Point

Use the Choose One type to Setup the Access Point field options to select the type of wizard to run.
The Typical Setup is the recommended wizard. This wizard uses the default parameters for most of the
configuration parameters and sets up a working network with the least amount of manual configuration.

The Advanced Setup wizard is for administrators who prefer more control over the different
configuration parameters. A few more configuration screens are available for customization when the
Advanced Setup wizard is used.

The first page of the Initial Setup Wizard displays the Navigation Panel and Function Highlights for
the configuration activities comprising the Access Point's initial setup. This page also displays options to
select the typical or advanced mode for the wizard.

The Navigation Panel for the Typical Setup Wizard displays the basic configuration options.

A green checkmark to the left of an item in the Navigation Panel defines the task as having its minimum
required configuration set correctly. A red X defines a task as still requiring at least one parameter be
defined correctly.

7. Select Save/Commit within each page to save the updates made to that page's configuration. Select
Next to proceed to the next page listed in the Navigation Panel without saving your updates.

NOTE While you can navigate to any page in the navigation panel, you cannot

complete the Initial AP Setup Wizard until each task in the Navigation
Panel has a green checkmark.

For the purposes of this guide, use the Typical Setup (Recommended) option to simplify the process of
getting the Access Point up and running quickly with a minimum number of changes to the Access Point’s
default configuration.

Installation Guide 17

For information on using the Access Point’s Advanced Setup option, refer to the WiNG Access Point
System Reference Guide to familiarize yourself with the feature set supported by the WiNG operating

system. The guide is available at www.zebra.com/support

.

To configure the Access Point using the Typical Setup Wizard:

8. Select Typical Setup from the Choose One type to Setup the Access Point field on the Initial Setup
Wizard.

The Typical Setup Wizard displays the Access Point Settings screen to define the Access Point's
Standalone versus Virtual Controller AP functionality. This screen also enables selection of the country of
operation for the Access Point.

9. Select an Access Point Type from the following options:

• Virtual Controller AP - When more than one Access Point is deployed, a single Access Point can
function as a Virtual Controller AP. Up to 24 Access Points can be connected to, and managed by,
a single Virtual Controller AP of the same Access Point model. These connected Access Points
must be the same model as the Virtual Controller AP.

• Standalone AP - Select this option to deploy this Access Point as an autonomous fat Access Point.
A Standalone AP isn't managed by a Virtual Controller AP, or adopted by a controller

NOTE If wanting to adopt the Access Point to a controller or service platform,

use the controller or service platform’s resident UI to connect to the
Access Point, provision its configuration and administrate the Access
Point’s configuration.

.

18 AP 6522M Access Point

NOTE If designating the Access Point as a Standalone AP, it is recommended

the Access Point’s UI be used exclusively to define its device
configuration, and not the CLI. The CLI provides the ability to define more
than one profile and the UI does not. Consequently, the two interfaces
cannot be used collectively to manage profiles without an administrator
encountering problems.

10. Select the Country Code of the country where the Access Point is deployed. Selecting a proper country

is a critical task while configuring the Access Point, as it defines the correct channels of operation and
ensures compliance to the regulations of the selected country. This field is only available for the Typical
Setup Wizard.

11. Select Next to set the Access Point’s network mode.

12. The Typical Setup Wizard displays the Network Topology screen to define how the Access Point handles

network traffic.

13. Select an Access Point Mode from the available options.

Installation Guide 19

• Router Mode -In Router Mode, the Access Point routes traffic between the local network (LAN) and
the Internet or external network (WAN). Router mode is recommended in a deployment supported by
just a single Access Point.

• Bridge Mode - In Bridge Mode, the Access Point depends on an external router for routing LAN and
WAN traffic. Routing is generally used on one device, whereas bridging is typically used in a larger
density network. Select Bridge Mode when deploying this Access Point with numerous peer Access
Points supporting clients on both the 2.4GHz and 5GHz radio bands.

NOTE When Bridge Mode is selected, WAN configuration cannot be performed

and the Typical Setup Wizard does not display the WAN configuration
screen.

14. Select Next. The Typical Setup Wizard displays the LAN Configuration screen to set the Access Point's

LAN interface configuration.

20 AP 6522M Access Point

15. Set the following DHCP and Static IP Address/Subnet information for the LAN interface:

• Use DHCP - Select the checkbox to enable an automatic network address configuration using the
Access Point’s DHCP server.

• Static IP Address/Subnet - Enter an IP Address and a subnet for the Access Point's LAN interface. If

Use DHCP is selected, this field is not available. When selecting this option, define the following DHCP
Server and Domain Name Server (DNS) resources, as those fields will become enabled on the bottom

portion of the screen.

• Use on-board DHCP server to assign IP addresses to wireless clients - Select the checkbox to
enable the Access Point’s DHCP server to provide IP and DNS information to clients on the LAN
interface.

• Range - Enter a starting and ending IP Address range for client assignments on the LAN interface.
Avoid assigning IP addresses from x.x.x.1 - x.x.x.10 and x.x.x.255, as they are often reserved for
standard network services. This is a required parameter.

• Default Gateway - Define a default gateway address for use with the default gateway. This is a
required parameter.

• DNS Forwarding - Select this option to allow a DNS server to translate domain names into IP
addresses. If this option is not selected, a primary and secondary DNS resource must be specified.
DNS forwarding is useful when a request for a domain name is made but the DNS server, responsible
for converting the name into its corresponding IP address, cannot locate the matching IP address.

• Primary DNS - Enter an IP Address for the main Domain Name Server providing DNS services for
the Access Point's LAN interface.

• Secondary DNS - Enter an IP Address for the backup Domain Name Server providing DNS services
for the Access Point's LAN interface.

Installation Guide 21

16. Select Next. The Typical Setup Wizard displays the Wireless LAN Setup screen to set the Access

Point’s Wireless LAN interface configuration.

17. Set the following WLAN1 Configuration parameters:

• SSID - Configure the SSID for the WLAN.

• WLAN Type - Configure the encryption and authentication to use with this WLAN.

• No Authentication and No Encryption - Configures a network without any authentication. This
option also configures the network without encryption. This means that any data transmitted
through the network is in plain text. Any device between end points can see the information
transmitted. This is the least secure of all network configurations.

• Captive Portal Authentication and No Encryption - Configures a network that uses a RADIUS server
to authenticate users before allowing them on to the network. Once on the network, no encryption
is used for the data being transmitted through the network. Select this option to use a Web page
(either internally or externally hosted) to authenticate users before access is granted to the
network.

• PSK authentication, WPA2 encryption - Configures a network that uses PSK authentication and
WPA2 encryption. Select this option to implement a pre-shared key that must be correctly shared
between the Access Point and requesting clients using this WLAN.

18. Select Next. The Typical Setup Wizard displays the RADIUS Server Configuration screen if required.

Otherwise, the Typical Setup Wizard displays the Summary and Commit screen.

22 AP 6522M Access Point

19. Use the Radius Server Configuration screen to configure the users for the onboard RADIUS server. Use

the screen to add, modify and remove RADIUS users.

20. Select Add User to display the dialog to enter user information to add to the RADIUS server user

database.

Installation Guide 23

21. Enter the following user information:

• Username - Provide a user name used to authenticate the user.

• Password - Provide a password used to authenticate the user.

• Confirm Password - Confirm the password by entering the same password as entered in the Password
field.

• Description - Provide a description to identify the user created in the RADIUS server database.

22. To create the entry in the RADIUS server database and add another user, select Create. To create the entry
in the RADIUS server database and close the Add User dialog, select Create & Close.

23. Select Modify User on the RADIUS Server Configuration screen to modify information for an existing user
from the RADIUS database. Highlight the user entry then select Modify User.

NOTE The Username cannot be modified with this dialog.

24. Select Delete User on the RADIUS Server Configuration screen to remove information for an existing
user from the RADIUS database. Highlight the user entry and select Delete User.

25. Select Confirm on the dialog displayed. The entry for the user is removed from the RADIUS database.

26. To dismiss the dialog without adding, modifying or removing entries in the RADIUS server database, select
Cancel.

24 AP 6522M Access Point

27. Select Next. The Typical Setup Wizard displays the Summary and Commit screen to summarize the
screens (pages) and settings updated using the Typical Setup Wizard.

No user intervention or additional settings are required. Its an additional means of validating the Access
Point’s updated configuration before it’s deployed. However, if a screen displays settings not intended as
part of the initial configuration, then any screen can be selected again from within the Navigation Panel
and its settings modified accordingly.

28. If the configuration displays as intended, select Save/Commit to implement these settings to the Access
Point’s configuration. If additional changes are warranted based on the summary, either select the target
page from the Navigational Panel, or use the Back and Next buttons to scroll to the target screen.

Installation Guide 25

4 Specifications

4.1 AP 6522M Integrated Antenna Model Electrical Characteristics

An AP 6522M Integrated model Access Point has the following electrical characteristics:

Operating Current &
Voltage

12VDC, 1A (accessory power connector)
48V,0.25A (PoE connector)

4.2 AP 6522M Integrated Antenna Model Physical Characteristics

An AP6522 Integrated Antenna model Access Point has the following physical characteristics:

Dimensions 5.25 inches x 6.0 inches x 1.25 inches

13.34 cm x 15.24 cm x 3.18 cm

Housing Plastic

Weight 0.80 lbs / 0.36 kg

Operating
Temperature

Storage Temperature -40°F to 185°F/-40°C to 85°C

Operating Humidity 5 to 95% Relative Humidity non-condensing

Storage Humidity 85% Relative Humidity non-condensing

Operating Altitude
(max)

Storage Altitude
(max)

32°F to 104°F/0°C to 40°C

8,000 ft @ 28C

30,000 ft @ 12C

Electrostatic
Discharge

+/-15kV Air and +/-8kV Contact @ 50% Relative Humidity

26 AP 6522M Access Point

4.3 Radio Characteristics

The AP 6522M model Access Points have the following radio characteristics:

Operating Channels All channels from 4920 MHz to 5825 MHz except channel

52 -64
Channels 1-13 (2412-2472 MHz)
Channel 14 (2484 MHz) Japan only
Actual operating frequencies depend on regulatory approval for the

country of use.

Data Rates Supported 802.11b: 1,2,5.5,11Mbps

802.11g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps

802.11a: 6,9,12,18,24,36,48, and 54Mbps

802.11n: MCS 0-15 up to 300Mbps

Wireless Medium Direct Sequence Spread Spectrum (DSSS),

Orthogonal Frequency Division Multiplexing (OFDM)
Spatial multiplexing (MIMO)

Network Standards 802.11a, 802.11b, 802.11g, 802.3, 802.11n

Maximum Available
Transmit Power

Transmit Power
Adjustment

Maximum available conducted transmit power per chain:

2.4 GHz: 21dBm
Maximum available conducted transmit power all chains:

2.4 GHz: 24dBm
Maximum available conducted transmit power per chain:

5 GHz: 19dBm
Maximum available conducted transmit power all chains:

5 GHz: 22dBm

1dB increments

Installation Guide 27

5 Regulatory Information

This guide applies to MODEL: AP-0622 (Part Number AP-6522M).

All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be
labeled as required.

Local language translations are available at the following Website: www.zebra.com/support

Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user's authority
to operate the equipment.

Zebra devices are professionally installed, the Radio Frequency Output Power will not exceed the maximum
allowable limit for the country of operation.

Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or
attachments could cause damage and may violate regulations.

.

5.1 Wireless Device Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for
use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe.

Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at:

www.zebra.com/doc

Note: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the
United Kingdom.

Operation of the device without regulatory approval is illegal.

.

5.1.1 Country Selection

Select only the country in which you are using the device. Any other selection will make the operation of this device
illegal.

28 AP 6522M Access Point

5.1.2 Frequency of Operation – FCC and IC

5 GHz Only

The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz) is restricted to Indoor
Use Only; any other use will make the operation of this device illegal.

5.1.3 Industry Canada Statement:

Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful
interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning
they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or
damage to LE-LAN devices.

The professional installer should utilize the Antenna Guide at www.zebra.com/support
configuration consistent with the FCC Grant and the IC Listing. The transmitter power settings for each of the
authorized antennas are contained in the Antenna Guide.

Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles
utilisant les mêmes canaux. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux
(c.-à-d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer
du brouillage et/ou des dommages aux dispositifs LAN-EL.

L'installateur professionnel devrait utiliser les Guides d'Antenne 72E-162906-01 à: www.zebra.com
une configuration accommodante en accord avec la Subvention de FCC et la Liste d'IC. Les cadres de pouvoir de
transmetteur pour chacune des antennes autorisées sont contenus dans le Guide d'Antenne.

2.4 GHz Only

The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited
by firmware.

to ensure a compliant

pour garantir

5.2 Health and Safety Recommendations

5.2.1 Warnings for Use of Wireless Devices

Please observe all warning notices with regard to the usage of wireless devices.

5.2.2 Potetially Hazerdous Atmospheres - Fixed Installations

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc.
and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).

Installation Guide 29

5.2.3 Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When
installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely
affected.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld
wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are
consistent with independent research and recommendations by Wireless Technology Research.

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimize the potential for interference.

• If you have any reason to suspect that interference is taking place, turn OFF your device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine if the operation of your
wireless product may interfere with the medical device.

5.3 RF Exposure Guidelines

5.3.1 Safety Information

Reducing RF Exposure - Use Properly

Only operate the device in accordance with the instructions supplied.

International

The device complies with internationally recognized standards covering human exposure to electromagnetic fields
from radio devices. For information on “International” human exposure to electromagnetic fields refer to the
Declaration of Conformity (DoC) at: www.zebra.com/doc

Europe

Remote and Standalone Antenna Configurations

To comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum separation
distance of 20 cm from all persons.

.

30 AP 6522M Access Point

US and Canada

Co-located statement

To comply with FCC RF exposure compliance requirement, the antennas used for this transmitter must not be
co-located or operating in conjunction with any other transmitter/antenna except those already approved in this
filling.

Remote and Standalone Antenna Configurations

To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum separation
distance of 20 cm from all persons.

To satisfy FCC RF exposure requirements, a mobile transmitting device must operate with a minimum separation
distance of 20 cm or more from a person's body.

5.4 Power Supply

Use ONLY a LISTED Type no. PWRS-14000-148R (12VDC @ 4.16A), direct plug-in power supply, marked Class 2
(IEC60950-1, SELV).

This device can be powered from a 802.3af compliant power source which is certified by the appropriate agencies.

Use of alternative Power Supply will invalidate any approvals given to this unit and may be dangerous.

5.5 Radio Frequency Interference Requirements—FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential

radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

5.5.1 Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The use of 5 GHz WLAN's, for use in the US , have the following restrictions

• Notched Band 5.60 – 5.65 GHz

installation. This equipment generates, uses and can

Installation Guide 31

5.5.2 Radio Frequency Interference Requirements – Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with Industry Canada licence-exempt RSS standard(s) Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Cet appareil se conforme Canada et Industrie Règles de normes de RSS permis-exempt. L'opération est assujetti
au suivre deux conditions : (1) cet appareil ne peut pas causer l'intervention nuisible, et (2) cet appareil doit accepter
de l'intervention reçue, y compris l'intervention qui peut causer l'opération non désirée.

Radio Transmitters(RSS-210)

For RLAN Devices:

The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:

• Restricted Band 5.60 – 5.65 GHz

This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de
licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible
de provoquer un fonctionnement indésirable.

This radio transmitter (identify the device by certification number, or model number if Category II) has been
approved by Industry Canada to operate with the antenna types listed in the Antenna Guide at

www.zebra.com/support

with the maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in guide, having a gain greater than the maximum gain indicated for
that type, are strictly prohibited for use with this device.

Cet émetteur radio (identifient l'artifice par le nombre de certification, ou nombre modèle si la Catégorie II) a été

approuvé par l'Industrie le Canada pour opérer avec les types d'antenne énumérés dans l'Antenne Guide à

www.zebra.com/support

avec l'augmentation permise maximum et a exigé l'impédance d'antenne pour chaque
type d'antenne indiqué. Les types d'antenne non inclus dans le guide, en ayant une augmentation plus grande
que l'augmentation maximum indiquée pour ce type, sont sévèrement interdits pour l'utilisation avec cet artifice.

Label Marking: The Term "IC:" before the radio certification signifies that Industry Canada technical specifications
were met.

32 AP 6522M Access Point

5.6 CE Marking and European Economic Area (EEA)

The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions:

• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.

• France outside usage, the equipment is restricted to 2.400-2.45 GHz frequency range.

• Italy requires a user license for outside usage.

5.6.1 Statement of Compliance

Zebra hereby, declares that this device is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from www.zebra.com/doc

.

Installation Guide 33

5.7 Waste Electrical and Electronic Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For
information on how to return product, please go to: www.zebra.com/weee.

Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra
pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : www.zebra.com/weee

Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo
de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite:

www.zebra.com/weee.

Български: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на
Zebra за рециклиране. За информация относно връщането на продукти, моля отидете на адрес:

www.zebra.com/weee

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an
Zebra zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter

www.zebra.com/weee

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere
restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il
seguente sito Web: www.zebra.com/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para
reciclagem. Para obter informações sobre como devolver o produto, visite: www.zebra.com/weee

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te
worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee
terugzenden van producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Zebra w
celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej

www.zebra.com/weee.

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Zebra
k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: www.zebra.com/weee
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile.
Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: www.zebra.com/weee
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás
céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a www.zebra.com/weee
weboldalra.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för
återvinning. Information om hur du returnerar produkten finns på www.zebra.com/weee
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun
tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs
oplysningerne om returnering af produkter på: www.zebra.com/weee

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται
στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση www.zebra.com/weee στο ∆ιαδίκτυο.

.

.

.

voor meer informatie over het

.

.

.

.

.

34 AP 6522M Access Point

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati
għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur:

www.zebra.com/weee

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la
Zebra pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi: www.zebra.com/weee

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za
informacije o vračilu izdelka obiščite: www.zebra.com/weee

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené
spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją
„Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite: www.zebra.com/weee
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai
pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu, skatiet: www.zebra.com/weee
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir.
Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: www.zebra.com/weee.

.

.

.

.

.

5.7.1 TURKISH WEEE Statement of Compliance

EEE Yönetmeli?ine Uygundur

Installation Guide 35

この装置は、情報処理装置等電波障害自主規制協議会（ ＶＣＣＩ）の基準に基づくクラスB情
報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この装置がラ
ジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。

5.8 Other Countries

Japan (VCCI) - Voluntary Control Council for Interference

Korea Warning Statement for Class B

Australia

Use of 5GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65GHz.

Brazil

Declarações Regulamentares para - Brasil

Nota: A marca de certificação se aplica ao Transceptor, modelo . Este equipamento opera em caráter secundário,
isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode
causar interferência a sistemas operando em caráter primário. Para maiores informações sobre ANATEL consulte
o site: www.anatel.gov.br

Chile

Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a
radiaciones electromagnéticas.

China

36 AP 6522M Access Point

Mexico

Restrict Frequency Range to: 2.450 – 2.4835 GHz.

"La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia,
incluyendo la que pueda causar su operación no deseada."

S. Korea

For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expression should be
displayed ;

Taiw an

在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用

Ukraine

This equipment corresponds to requirements of the Technical Regulation No. 1057, 2008 on restrictions as to the
use of some dangerous substances in electric and electronic devices.

Thailand

Installation Guide 37

6 Support

If you have a problem with your equipment, contact support for your region.

Contact information is available at: www.zebra.com/support

When contacting support, please provide the following information:

• Serial number of the unit

• Model number or product name

• Software type and version number

Support responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you
purchased your product from a business partner, contact that business partner for support.

Customer Support Web Sites

The Support site, located at www.zebra.com/support
developer tools, software downloads, product manuals and online repair requests.

Manuals

www.zebra.com/support

.

provides information and online assistance including

38 AP 6522M Access Point

7 Symbol Technologies End-User Software License Agreement

This End-User Software License Agreement ("End-User License Agreement") is between Symbol Technologies Inc.
(herein "Symbol Technologies") and End-User Customer to whom Symbol Technologies' proprietary software or
Symbol Technologies Products containing embedded, pre-loaded, or installed software ("Products") is made
available. This End-User License Agreement contains the terms and conditions of the license Symbol Technologies
is providing to End-User Customer, and End-User Customer's use of the Software and Documentation. By using,
downloading or installing this software, you or the entity that you represent ("End-User Customer") are consenting
to be bound by and are becoming a party to this End-User License Agreement.

1. DEFINITIONS

“Documentation” means product and software documentation that specifies technical and performance

features and capabilities, and the user, operation and training manuals for the Software (including all
physical or electronic media upon which such information is provided).

“Open Source Software” means software with either freely obtainable source code license for
modification, or permission for free distribution.

“Open Source Software License” means the terms or conditions under which the Open Source
Software is licensed.

“Software” (i) means proprietary software in object code format, and adaptations, translations,
decompilations, disassemblies, emulations, or derivative works of such software; (ii) means any
modifications, enhancements, new versions and new releases of the software provided by Symbol
Technologies; and (iii) may contain items of software owned by a third party supplier. The term
“Software” does not include any third party software provided under separate license or third party
software not licensable under the terms of this Agreement. To the extent, if any, that there is a separate
license agreement packaged with, or provided electronically with, a particular Product that becomes
effective on an act of acceptance by the end user, then that agreement supersedes this End-User License
Agreement as to the end use of that particular Product.

2. GRANT OF LICENSE

2.1 Subject to the provisions of this End-User License Agreement, Symbol Technologies grants to End-User

Customer a personal, limited, non-transferable (except as provided in Section 4), and non-exclusive
license under Symbol Technologies’ copyrights and confidential information embodied in the Software to
use the Software, in object code form, and the Documentation solely in connection with End-User
Customer’s use of the Products. This End-User License Agreement does not grant any rights to source
code.

Installation Guide 39

2.2 If the Software licensed under this End-User License Agreement contains or is derived from Open Source

Software, the terms and conditions governing the use of such Open Source Software are in the Open
Source Software Licenses of the copyright owner and not this End-User License Agreement. If there is a
conflict between the terms and conditions of this End-User License Agreement and the terms and
conditions of the Open Source Software Licenses governing End-User Customer’s use of the Open Source
Software, the terms and conditions of the license grant of the applicable Open Source Software Licenses
will take precedence over the license grants in this End-User License Agreement. If requested by
End-User Customer, Symbol Technologies will use commercially reasonable efforts to: (i) determine
whether any Open source Software is provided under this End-User License Agreement; (ii) identify the
Open Source Software and provide End-User Customer a copy of the applicable Open Source Software
License (or specify where that license may be found); and, (iii) provide End-User Customer a copy of the
Open Source Software source code, without charge, if it is publicly available (although distribution fees
may be applicable).

3. LIMITATIONS ON USE

3.1 End-User Customer may use the Software only for End-User Customer’s internal business purposes and

only in accordance with the Documentation. Any other use of the Software is strictly prohibited and will
be deemed a breach of this End-User License Agreement. Without limiting the general nature of these
restrictions, End-User Customer will not make the Software available for use by third parties on a “time
sharing,” “application service provider,” or “service bureau” basis or for any other similar commercial
rental or sharing arrangement.

3.2 End-User Customer will not, and will not allow or enable any third party to: (i) reverse engineer,

disassemble, peel components, decompile, reprogram or otherwise reduce the Software or any portion to
a human perceptible form or otherwise attempt to recreate the source code; (ii) modify, adapt, create
derivative works of, or merge the Software with other software; (iii) copy, reproduce, distribute, lend, or
lease the Software or Documentation to any third party, grant any sublicense or other rights in the
Software or Documentation to any third party, or take any action that would cause the Software or
Documentation to be placed in the public domain; (iv) remove, or in any way alter or obscure, any
copyright notice or other notice of Symbol Technologies’ proprietary rights; (v) provide, copy, transmit,
disclose, divulge or make the Software or Documentation available to, or permit the use of the Software
by any third party or on any machine except as expressly authorized by this Agreement; or (vi) use, or
permit the use of, the Software in a manner that would result in the production of a copy of the Software
solely by activating a machine containing the Software. End-User Customer may make one copy of
Software to be used solely for archival, back-up, or disaster recovery purposes; provided that End-User
Customer may not operate that copy of the Software at the same time as the original Software is being

40 AP 6522M Access Point

operated. End-User Customer may make as many copies of the Documentation as it may reasonably
require for the internal use of the Software.

3.3 Unless otherwise authorized by Symbol Technologies in writing, End-User Customer will not, and will not

enable or allow any third party to: (i) install a licensed copy of the Software on more than one unit of a
Product; or (ii) copy onto or transfer Software installed in one unit of a Product onto another device.

3.4 If End-User Customer is purchasing Products that require a site license, End-User Customer must

purchase a copy of the applicable Software for each site at which End-User Customer uses such
Software. End-User Customer may make one additional copy for each computer owned or controlled by
End-User Customer at each such site. End-User Customer may temporarily use the Software on portable
or laptop computers at other sites. End-User Customer must provide a written list of all sites where
End-User Customer uses or intends to use the Software.

4. TRANSFERS

4.1 End-User Customer will not transfer the Software or Documentation to any third party without Symbol

Technologies’ prior written consent. Symbol Technologies’ consent may be withheld at its discretion and
may be conditioned upon transferee paying all applicable license fees and agreeing to be bound by this
End-User License Agreement.

5. OWNERSHIP AND TITLE

5.1 Symbol Technologies, its licensors, and its suppliers retain all of their proprietary rights in any form in

and to the Software and Documentation, including, but not limited to, all rights in patents, patent
applications, inventions, copyrights, trademarks, trade secrets, trade names, and other proprietary rights
in or relating to the Software and Documentation. No rights are granted to End-User Customer under this
Agreement by implication, estoppel or otherwise, except for those rights which are expressly granted to
End-User Customer in this End-User License Agreement. All intellectual property developed, originated,
or prepared by Symbol Technologies in connection with providing the Software, Products, Documentation
or related services remains vested exclusively in Symbol Technologies, and End-User Customer will not
have any shared development or other intellectual property rights.

Installation Guide 41

6. CONFIDENTIALITY

6.1 End-User Customer acknowledges that the Software contains valuable proprietary information and trade

secrets and that unauthorized dissemination, distribution, modification, reverse engineering,
disassembly or other improper use of the Software will result in irreparable harm to Symbol
Technologies for which monetary damages would be inadequate. Accordingly, End-User Customer will
limit access to the Software to those of its employees and agents who need to use the Software for
End-User Customer’s internal business

7. MAINTENANCE AND SUPPORT

7.1 No maintenance or support is provided under this End-User License Agreement. Maintenance or support,

if available, will be provided under a separate Software maintenance and support agreement.

8. LIMITED WARRANTY AND LIMITATION OF LIABILITY

8.1 Unless otherwise specified in the applicable warranty statement, the Documentation or in any other

media at the time of shipment of the Software by Symbol Technologies, and for the warranty period
specified therein, for the first 120 days after initial shipment of the Software to the End-User Customer,
Symbol Technologies warrants that the Software, when installed and/or used properly, will be free from
reproducible defects that materially vary from its published specifications. Symbol Technologies does
not warrant that End-User Customer’s use of the Software or the Products will be uninterrupted or
error-free or that the Software or the Products will meet End-User Customer’s particular requirements.

8.2 SYMBOL TECHNOLOGIES’ TOTAL LIABILITY, AND END-USER CUSTOMER’S SOLE REMEDY, FOR ANY

BREACH OF THIS WARRANTY WILL BE LIMITED TO, AT SYMBOL TECHNOLOGIES’ OPTION, REPAIR OR
REPLACEMENT OF THE SOFTWARE OR PAYMENT OF END-USER CUSTOMER’S ACTUAL DAMAGES UP
TO THE AMOUNT PAID TO SYMBOL TECHNOLOGIES FOR THE SOFTWARE OR THE INDIVIDUAL
PRODUCT IN WHICH THE SOFTWARE IS EMBEDDED OR FOR WHICH IT WAS PROVIDED. THIS
WARRANTY EXTENDS ONLY TO THE FIRST END-USER CUSTOMER; SUBSEQUENT TRANSFEREES MUST
ACCEPT THE SOFTWARE “AS IS” AND WITH NO WARRANTIES OF ANY KIND. SYMBOL
TECHNOLOGIES DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR
PURPOSE.

8.3 IN NO EVENT WILL SYMBOL TECHNOLOGIES BE LIABLE FOR SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF USE, TIME OR DATA,
INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS, OR SAVINGS, TO THE FULL EXTENT SUCH MAY

42 AP 6522M Access Point

BE DISCLAIMED BY LAW, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE
LIMITATIONS IN THIS PARAGRAPH WILL APPLY NOTWITHSTANDING ANY FAILURE OF ESSENTIAL
PURPOSE OF ANY LIMITED REMEDY.

9. TERM AND TERMINATION

9.1 Any use of the Software, including but not limited to use on the Products, will constitute End-User

Customer’s agreement to this End-User License Agreement. End-User Customer’s right to use the
Software will continue for the life of the Products with which or for which the Software and
Documentation have been provided by Symbol Technologies, unless End-User Customer breaches this
End-User License Agreement, in which case this End-User License Agreement and End-User Customer’s
right to use the Software and Documentation may be terminated immediately by Symbol Technologies. In
addition, if Symbol Technologies reasonably believes that End-User Customer intends to breach this
End-User License Agreement Symbol Technologies may, by notice to End-User Customer, terminate
End-User Customer’s right to use the Software.

9.2 Upon termination, Symbol Technologies will be entitled to immediate injunctive relief without proving

damages and, unless End-User Customer is a sovereign government entity, Symbol Technologies will
have the right to repossess all copies of the Software in End-User Customer’s possession. Within thirty
(30) days after termination of End-User Customer’s right to use the Software, End-User Customer must
certify in writing to Symbol Technologies that all copies of such Software have been returned to Symbol
Technologies or destroyed.

10. UNITED STATES GOVERNMENT LICENSING PROVISIONS

10.1 This Section applies if End-User Customer is the United States Government or a United States

Government agency. End-User Customer’s use, duplication or disclosure of the Software and
Documentation under Symbol Technologies’ copyrights or trade secret rights is subject to the restrictions
set forth in subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights clause
at FAR 52.227-19 (JUNE 1987), if applicable, unless they are being provided to the Department of
Defense. If the Software and Documentation are being provided to the Department of Defense, End-User
Customer’s use, duplication, or disclosure of the Software and Documentation is subject to the restricted
rights set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013 (OCT 1988), if applicable. The Software and Documentation may or may not
include a Restricted Rights notice, or other notice referring to this End-User License Agreement. The
provisions of this End-User License Agreement will continue to apply, but only to the extent that they are

Installation Guide 43

consistent with the rights provided to the End-User Customer under the provisions of the FAR and DFARS
mentioned above, as applicable to the particular procuring agency and procurement transaction.

11. GENERAL

11.1 Copyright Notices

. The existence of a copyright notice on the Software will not be construed as an
admission or presumption that public disclosure of the Software or any trade secrets associated with the
Software has occurred.

11.2 Compliance with Laws

. End-User Customer acknowledges that the Software is subject to the laws and
regulations of the United States and End-User Customer will comply with all applicable laws and
regulations, including export laws and regulations of the United States. End-User Customer will not,
without the prior authorization of Symbol Technologies and the appropriate governmental authority of
the United States, in any form export or re-export, sell or resell, ship or reship, or divert, through direct or
indirect means, any item or technical data or direct of indirect products sold or otherwise furnished to
any person within any territory for which the United States Government or any of its agencies at the time
of the action, requires an export license or other governmental approval. Violation of this provision is a
material breach of this Agreement.

11.3 Third Party Beneficiaries

. This End-User License Agreement is entered into solely for the benefit of
Symbol Technologies and End-User Customer. No third party has the right to make any claim or assert
any right under this Agreement, and no third party is deemed a beneficiary of this End-User License
Agreement. Notwithstanding the foregoing, any licensor or supplier of third party software included in
the Software will be a direct and intended third party beneficiary of this End-User License Agreement.

11.4 Waiver. No waiver of a right or remedy of a Party will constitute a waiver of another right or remedy of
that Party.

11.5 Assignments

. Symbol Technologies may assign any of its rights or sub-contract any of its obligations
under this End-User License Agreement or encumber or sell any of its rights in any Software, without
prior notice to or consent of End-User Customer.

11.6 Causes of Action

. End-User Customer must bring any action under this End-User License Agreement
within one year after the cause of action arises except that warranty claims must be brought within the
applicable warranty period.

11.7 Entire Agreement and Amendment
agreement regarding End-User Customer’s use of the Software and may be amended only in a writing
signed by both parties, except that Symbol Technologies may modify this End-User License Agreement as
necessary to comply with applicable laws and regulations.

. This End-User License Agreement contains the parties’ entire

44 AP 6522M Access Point

11.8 Governing Law. This End-User License Agreement is governed by the laws of the the State of Delaware
in the United States to the extent that they apply and otherwise by the internal substantive laws of the
country to which the Software is shipped if End-User Customer is a sovereign governmental entity. The
terms of the U.N. Convention on Contracts for the International Sale of Goods do not apply. In the event
that the Uniform Computer information Transaction Act, any version of this Act, or a substantially similar
law (collectively “UCITA”) becomes applicable to a Party’s performance under this Agreement, UCITA
does not govern any aspect of this End-User License Agreement or any license granted under this
End-User License Agreement, or any of the parties’ rights or obligations under this End-User License
Agreement. The governing law will be that in effect prior to the applicability of UCITA.

11.8 Dispute Resolution
from or in connection with this End-User License Agreement shall be submitted to the sole and exclusive
forum of the state and federal courts sitting in New Castle County, Delaware (the "Delaware Courts"),
and each Party irrevocably submits to the jurisdiction of the Delaware Courts for the litigation of such
disputes. Each Party hereby irrevocably waives, and agrees not to assert in any suit, action or proceeding
brought in the Delaware Courts, any claim or defense that the Party is not subject to the jurisdiction of
the Delaware Courts, that the Delaware Courts are an inconvenient forum, or that the Delaware Courts
are an improper venue.

. Unless End-User Customer is a sovereign governmental entity, any dispute arising

Installation Guide 45

46 AP 6522M Access Point

Installation Guide 47

Zebra Technologies Corporation.
475 Half Day Road, Suite 500, Lincolnshire, IL 60069 USA

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol
Technologies, Inc., a Zebra Technologies company.

© 2015 Symbol Technologies, Inc.

MN001464A01 Revision B April 2015