Product Safety and RF Energy Exposure Booklet for Mobile Two-Way Radios Installed in Vehicles or as Fixed Site Control Stations
ATTENTION!
BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS.
The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002.
© Motorola, Inc. 2005 |
*6881095C99* |
|
|
8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322 |
68P81095C99-E |
|
English
RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occupational Use Requirements
NOTICE: This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use.
This 2-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material.
Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection.
All Motorola 2-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of 2-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it.
English |
2 |
|
|
Please refer to the following Web sites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits.
http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html
The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile 2-way radios before they can be marketed in the U.S. When 2-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a label directing users to specific user awareness information. Your Motorola 2-way radio has a RF exposure product label. Also, your Motorola user manual, or separate safety booklet, includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements.
Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio antenna radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode.
3 |
English |
|
|
|
|
Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:
•United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J
•American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992
•Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
•International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
•Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999
•Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard, 2003
•ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) “additional requirements for SMR, cellular, and PCS product certification.”
RF Exposure Compliance and Control Guidelines and Operating
Instructions
To control exposure to yourself and others and to ensure compliance with the RF exposure limits, always adhere to the following procedures.
•User awareness instructions should accompany device when transferred to other users.
•Do not use this device if the operational requirements described herein are not met.
•Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button or, for radios equipped with VOX, speak into the microphone. The red LED will illuminate when the radio is
English |
4 |
|
|
transmitting. To receive calls, release the PTT button, or, for radios equipped with VOX, stop talking. The red LED will extinguish when the radio stops transmitting. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance).
•Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away, as shown in Table 1, from the body of a vehicle with a properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed (according to installation instructions) externally-mounted antenna to satisfy the RF exposure requirements in the standards listed above.
NOTE: Table 1 below lists the recommended lateral distance for people in an uncontrolled environment from the body of a vehicle with an approved, properly installed transmitting antenna (i.e., monopoles over a ground plane, or dipoles) at several different ranges of rated radio power for mobile radios installed in a vehicle.
Table 1. Rated Power of Vehicle-Installed Mobile Two-Way Radio and Recommended Minimum Lateral Distance from Vehicle Body
Mobile Radio Rated |
Minimum Lateral Distance from |
Power (see Note) |
Vehicle Body |
|
|
Less than 7 watts |
8 inches (20 centimeters) |
|
|
7 to 15 watts |
1 foot (30 centimeters) |
|
|
16 to 39 watts |
2 feet (60 centimeters) |
|
|
40 to 110 watts |
3 feet (90 centimeters) |
|
|
•When a mobile radio is used in conjunction with another co-located transmitter such as a Vehicular Repeater, it is the vehicle operator’s responsibility to take appropriate steps to keep bystanders at the required separation distance from the vehicle to ensure compliance with the FCC's RF energy exposure limits for the general population. See the co-located transmitter’s user manual for more details.
5 |
English |
|
|
|
|
NOTE: If you are not sure of the rated power of your radio, contact your Motorola representative or dealer and supply the radio model number found on the radio model label. If you can not determine the rated power out, then assure 3-feet separation from the body of the vehicle. The maximum power shown on the FCC Grant may be higher than the rated power allowing for production variation.
•These mobile antenna installation guidelines are limited to metal body motor vehicles or vehicles with appropriate ground planes.
•Antennas should be installed in the center area of the roof or the trunk lid taking into account exposure conditions of backseat passengers and according to the specific instructions and restrictions in the Radio Installation Manual along with the requirements of the antenna supplier.
•Trunk lid installations are limited to vehicles with clearly defined flat trunk lids, and in some cases, to specific radio models and antennas. See the Radio Installation Manual for specific information on how and where to install specific types of approved antennas to facilitate recommended operating distances to all potentially exposed persons.
•Use only the Motorola-approved, supplied antenna or a Motorolaapproved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may result in non-compliance with RF Safety Standards.
•This radio has been tested and meets RF Safety Standards when used with the Motorola accessories supplied or designated for this product. Use of other accessories may result in non-compliance with RF Safety Standards.
•For a list of Motorola-approved antennas, visit the following Web site, which lists approved accessories for your radio model: http://www.motorola.com/cgiss/index.shtml.
English |
6 |
|
|
For additional information on exposure requirements or other training information, visit http://www.motorola.com/rfhealth.
Compliance and Control Guidelines and Operating Instructions for Mobile Two-Way Radios Installed as Fixed Site Control Stations
If mobile radio equipment is installed at a fixed location and operated as a control station or as a fixed unit, the antenna installation must comply with the following requirements in order to ensure optimal performance and compliance with the RF energy exposure limits in the standards and guidelines listed on page 4:
•The antenna should be mounted outside the building on the roof or a tower if at all possible.
•As with all fixed site antenna installations, it is the responsibility of the licensee to manage the site in accordance with applicable regulatory requirements and may require additional compliance actions such as site survey measurements, signage, and site access restrictions in order to ensure that exposure limits are not exceeded.
•For additional installation information, see the guidelines for minimum separation distances provided above in the RF Exposure Compliance and Control Guidelines and Operating Instructions section of this document.
NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. It may be necessary to conduct compatibility testing to determine if any electronic equipment used in or around vehicles or near fixed site antenna is sensitive to external RF energy or if any procedures need to be followed to eliminate or mitigate the potential for interaction between the radio transmitter and the equipment or device.
7 |
English |
|
|
|
|
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.
To avoid possible interaction between the radio transmitter and any vehicle electronic control modules, such as ABS, engine, or transmission controls, the radio should be installed only by an experienced installer and the following precautions should be used when installing the radio:
1.Refer to the manufacturer’s instructions or other technical bulletins for recommendations on radio installation.
2.Before installing the radio, determine the location of the electronic control modules and their harnesses in the vehicle.
3.Route all radio wiring, including the antenna transmission line, as far away as possible from the electronic control units and associated wiring.
Check the laws and regulations on the use of radios in the area where you drive. Always obey them.
When using your radio while driving, please:
•Give full attention to driving and to the road.
•Pull off the road and park before making or answering a call if driving conditions so require.
English |
8 |
|
|
!Do not mount or place a mobile radio in the area over an air bag
W A R N I N G or in the air bag deployment area. Air bags inflate with great force. If a radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.
Turn off your radio prior to entering any area with a potentially explosive atmosphere. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.
The areas with potentially explosive atmospheres include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted.
9 |
English |
|
|
|
|
!To avoid possible interference with blasting operations, turn off
W A R N I N G your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Obey all signs and instructions.
For radios installed in vehicles fueled by liquefied petroleum gas, refer to the (U.S.) National Fire Protection Association standard, NFPA 58, for storage, handling, and/or container information. For a copy of the LP-gas standard, NFPA 58, contact the National Fire Protection Association, One Battery Park, Quincy, MA.
English |
10 |
|
|
Folleto de normas de seguridad y de exposición a la energía de RF al usar radios bidireccionales móviles instalados en vehículos o estaciones de control en emplazamientos fijos
ATENCIÓN
ANTES DE USAR EL RADIO LEA ESTE FOLLETO, EL CUAL CONTIENE INSTRUCCIONES DE OPERACIÓN IMPORTANTES PARA SU USO SEGURO, ASÍ COMO INFORMACIÓN SOBRE LA ENERGÍA DE RF Y SU CONTROL, PARA GARANTIZAR SU CONFORMIDAD CON LOS LÍMITES DE EXPOSICIÓN A LA ENERGÍA DE RADIOFRECUENCIA ESTABLECIDOS EN LAS NORMAS NACIONALES E INTERNACIONALES APLICABLES.
La información incluida en este documento reemplaza la información de seguridad general contenida en los manuales de usuario publicados antes de febrero de 2002.
© Motorola, Inc. 2005 |
*6881095C99* |
8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322, EE.UU. |
68P81095C99-E |
|
Español
Información sobre exposición a la energía de RF y su control, e instrucciones operacionales para satisfacer los requisitos de la FCC sobre el uso como herramienta ocupacional
AVISO: Este radio está diseñado para uso en ambientes ocupacionales controlados, donde los usuarios están plenamente conscientes de la exposición a la energía de radiofrecuencia a la que están sujetos, y pueden ejercer control sobre dicha exposición para mantenerse dentro de los límites establecidos por la FCC. Esta unidad de radio NO está aprobada para la venta al público en general en el mercado de consumo masivo, ni para uso en entornos diferentes al aquí descrito.
Este radio bidireccional usa energía electromagnética en el espectro de radiofrecuencia (RF) para permitir las comunicaciones a distancia entre dos o más usuarios. El mismo emplea la energía de radiofrecuencia u ondas de radio para enviar y recibir llamadas. La energía de RF es una forma de energía electromagnética. Este tipo de energía se presenta en otras formas, entre las que se encuentran la luz solar y los rayos X. La energía de RF, sin embargo, no debe confundirse con estas otras formas de energía electromagnética que, cuando son usadas indebidamente, pueden ocasionar daños biológicos. Niveles muy elevados de rayos X, por ejemplo, pueden producir daños en tejidos y en material genético.
Expertos en las ciencias, la ingeniería, la medicina, la salud y la industria trabajan conjuntamente con diferentes organizaciones con el fin de desarrollar normas que definan límites prudentes de exposición a la energía de RF. Estas normas proporcionan los niveles recomendados de exposición a la RF, tanto para los trabajadores como para el público en general. Estos niveles recomendados de exposición a la RF incluyen márgenes de seguridad suficientemente amplios. Todos los radios bidireccionales Motorola son diseñados, fabricados y probados de manera que aseguren el cumplimiento de los niveles de exposición a la RF establecidos por los organismos públicos reguladores. Asimismo, los fabricantes recomiendan a los usuarios de radios bidireccionales seguir instrucciones de operación específicas. Estas instrucciones son importantes, ya que informan a los usuarios acerca de la exposición a la energía de RF y proporcionan procedimientos sencillos para su control.
Español |
2 |
|
|