Motorola 92FT5826 Users manual

iDEN Data Module iO1500R

Application and Integration

Developers Guide

Release 1.3 May 15, 2003

Documentation Copyrights

No duplication or distribution of this document or any portion thereof shall take place

without the express written permission of Motorola. No part of this manual may be

reproduced, distributed, or transmitted in any form or by any means, electronic or

mechanical, for any purpose without the express written permission of Motorola. To

order additional copies contact your Motorola sales representative.

68P02954C65-O

20/5/03 page 1 of 37

(

DECLARATION OF CONFORMITY

Per FCC CFR 47 part 2 Section 2.1077(a)

Responsible party name: Motorola Inc. Address: 8000 West Sunrise Boulevard,

Phone number: 1

Hereby declares that the product:

Product name: iO1500R Model Number: F2572A FCC ID:

Conforms to the following regulation:

FCC Part 15, subpart B Class B Computer Peripheral Device

Date: MAY 15, 2003

ote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Plantation, FL 33322 USA

800) 453-0920

Z492FT5826

20/5/03 page 2 of 37

DECLARATION OF CONFORMITY ..................................................................................2

Revision History .......................................................................................................................5

Purpose Of This Document......................................................................................................5

Distribution ...............................................................................................................................5

Related Documentation............................................................................................................5

Module Descriptions and Specifications.................................................................................6

iO15 Modem Product Specificationss ......................................................................6

Electrical specifications: ........................................................................................6

Environmental Specifications ................................................................................ 6

Other Specifications............................................................................................... 6

iO1500R Evaluation board ......................................................................................................7

Safety Notice - ATTENTION .................................................................................................7

FCC Regulation - Letter of Notice.............................................................................7

iO1500R Hardware Interfacing Information.........................................................................8

Mechanical Dimensions.............................................................................................8

Connector Types:.......................................................................................................9

Accessory Connector Pin Functions ........................................................................10

Status LED Indications ............................................................................................12

Voice Support ..........................................................................................................12

Design Considerations For iO1500R OEM Developers ......................................................13

Hardware Considerations.........................................................................................13

Software Considerations ..........................................................................................13

Module Software And Interface Modes ...............................................................................14

Circuit Switched Data..........................................................................................14

Packet Data ..........................................................................................................14

Managing User Image Profiles ..............................................................................................15

Warning When Switching User Image Profiles....................................................... 15

Setting The Active User Image................................................................................ 15

Properly configuring, saving, and restoring user image profiles.............................16

Changing the settings of a user image .................................................................16

Restoring the settings of a saved user image .......................................................16

How To Use Hayes Compatible Packet Data mode.............................................................17

How to use Hayes Compatible Packet Data mode (Continued) ..........................19

Other Useful AT Commands ...............................................................................19

Reset, Master Reset,Power off.................................................................................20

AT Command To RESET the iO1500R. .............................................................20

AT Command For Master Reset..........................................................................20

AT Command To Power the iO15 off. ................................................................20

SIM AT commands,.................................................................................................20

AT Command To Unlock the iO15 SIM card. ....................................................20

AT Command To enable or disable the SIM PIN lock mechanism. ...................21

Other useful iO15 AT commands ............................................................................21

Service Status Log (SSL) AT command..............................................................21

PC Applications To Control the iO1500R...............................................................22

FVN4780A - iDEN module - Packet Data Applet...............................................22

Status Program.....................................................................................................22

Configuration Program ........................................................................................22

Service Program................................................................................................... 22

iDEN data modules – Software integration..........................................................................23

20/5/03 page 3 of 37

Additional Information For Registering and Going Offline ..............................................25

Module Activation and Registration........................................................................25

To make the iO1500R module re-register perform these steps: ..........................25

Monitoring The RS232 CD pin and Going Offline: ............................................25

Packet Data Status Information Command.......................................................... 26

IP Address/ Network Entity Identifier (NEI) Command .....................................27

Summary Of AT Commands.................................................................................................28

General AT Commands..............................................................................................28

User Image Profile Management Commands..................................................................28

Hayes Compatible Packet Data Commands....................................................................28

Registration, Reset, and power off Commands................................................................28

SIM card management Commands ...............................................................................28

Network Status Commands.........................................................................................29

Appendix A: Requirements For FCC Testing .....................................................................30

20/5/03 page 4 of 37

Revision History

Date Revision Comments

May 5, 2003

1.3 Initial Release.

Purpose Of This Document

This guide is for the application developer and system integrator who plan to use the iO1500R iDEN data module in their design of an OEM product. This manual describes the requirements and interfaces for the integration of the iDEN iO1500R wireless module into OEM terminal/equipment. These requirements include instructions for FCC testing, requirements for use with wireless carriers, setup instructions, pin descriptions, available software, useful AT commands, and design considerations. This document also covers how to use the iO1500R via Hayes Compatible Packet Data mode with older legacy equipment whose software cannot support packet data.

Distribution

This manual will be distributed to the developer on a CD or will be obtainable from the iDEN Developers web site. This document will refer to related documents and software, which can aid the OEM designer in integrating the iO1500R into their product.

Module Descriptions and Specifications

The iO1500R module for iDEN is a wireless subscriber device for providing packet data and circuit data connectivity over the iDEN 800MHz infrastructure. The module is supported by PC applications for installation, monitoring, service and development for the OEM and the system integrator.

iO1500R Module Product Specificationss

Electrical specifications:

Frequency TX 806-825 MHz RX 851-870 MHz TX Output Power Average 0.6 watts at nominal 3.6V & 25 °C Input Voltage 3.6VDC +/- 5 % ripple 50mv Current Consumption Standby Current avg. 20mA

Tx Current in slot Avg. 1:6 1000mA Max

Rx Current in slot Avg. 1:6 100 mA Max Tx. Modulation Circuit Data / Voice Quad -16 QAM; Packet Data Quad-64 QAM, Quad-16 QAM and QPSK; Trans. ACCPR -60 dB @ 25 KHz

-74.5 dB @ 1000 KHz Static Rx Sensitivity -111 dBm @ -10% BER

Environmental Specifications

Operating Temp -25°C to 60°C Storage Temp -40°C to 85°C Humidity: 95% RH @ 50°C , non condensing Vibration: Sine TIA/EIA 603 Para. 3.3.4 Shock TIA/EIA 603 Para. 3.3.5

Other Specifications

Size 85.6 X 57.7 X 6.0mm Weight 30 grams

For module description, features and specifications refer to the iO1500R brochure or get the information from the WEB at http://ml800.motorola.com/ => iO1500R.

=>Module Modems

20/5/03 page 6 of 37

iO1500R Evaluation board

The evaluation board helps the developer and system integrator to start development of the software before their terminal hardware is ready. The developer can connect a PC to the evaluation board and communicate with the iO1500R that is registered to the system and work over the iDEN infrastructure. For more information see the OEM Evaluation Board User Guide 68P02954C85-O.

Safety Notice - ATTENTION

This iDEN iO1500R Module is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet (Motorola Publication part number 6881095C99) to ensure compliance with RF energy exposure limits.

FCC Regulation - Letter of Notice

As you know, the iO1500R RF module that we are supplying to you for incorporation into Final Products are components that, when connected to the power supply, internal signaling, and antenna in a Final Product can receive and transmit module signals.

In the United States, the Federal Communications Commission requires that many module transmitting devices obtain approval before being offered on the market, unless the device is exempt. While the iO1500R has been designed to meet applicable FCC requirements, provided in the code of Federal Regulation 47CFR part II subpart J and 47CFR part 90 subpart S, the Final Product's compliance with the FCC's requirements, including RF energy exposure requirements, must reflect product usage, positioning of the iO1500R within the product, the type of antenna used, the location of the antenna, and other factors that may vary with the design and nature of the Final Product. Therefore, compliance with such FCC requirements can only be determined by an assessment of the Final Product.

It is important that any manufacturer to whom you resell the iO1500R for use in a final product also recognize that they will have the responsibility for taking all necessary steps to ensure that the Final Product meets any applicable FCC requirements and for obtaining any necessary approval from the FCC for sale and operation of the Final Product. To the extent that this may require testing and assessment of the Final Product, this will be the responsibility of the manufacturer.

To the extent that this may require development of user information or guidance to be provided to each purchaser of the Final Product, this will also be the responsibility of the manufacturer.

Information covering the FCC tests that are required is located in Appendix A.

Please provide a copy of this reminder to every manufacturer to whom you resell these products.

20/5/03 page 7 of 37

iO1500R Hardware Interfacing Information

Mechanical Dimensions

20/5/03 page 8 of 37

Connector Types:

The unit has two connectors:

• RF output connector MMCX Jack (female) 50 Ohm. This will accept the

RG 178-11 MMCX-50-1-1 Plug (male) or RG 316-11 MMCX-50-2-3 (male).

 The Data Interface connector is a MOLEX 30-pin ZIF connector,

MOLEX part #: 52892-3090.

Motorola Part #: 0909059E06.

OEM developers must also use this 30-wire flex cable to interface to the

connector:

AXON Cable Part#: FFC0.50A30/0035L3-3-06-06SBBB.

Motorola Part #: 3086229J04.

20/5/03 page 9 of 37

Accessory Connector Pin Functions

PIN # PIN NAME DIRECTION DESCRIPTION Notes

RS232_RX OUT RS232 Signal 3V Max

RS232_TX IN RS232 Signal 3V Max

RS232_DTR IN RS232 Signal 3V Max

RS232_DCD OUT RS232 Signal 3V Max

RS232_GND IN Signal Ground

RS232_RTS IN RS232 Signal 3V Max

RS232_CTS OUT RS232 Signal 3V Max

RS232_DSR OUT RS232 Signal 3V Max

RS232_RI OUT RS232 Signal 3V Max

EXT_MIC IN Audio input to iO1500R FUTURE USE

AUDIO_COMMON IN Analog Ground FUTURE USE

AUDIO_OUT OUT iO1500R Audio Out FUTURE USE

OPT_SELECT_1 I/O (22K pull-up) iO1500R configuration Control Signal

OPT_SELECT_2 I/O (22K pull-up) iO1500R configuration Control Signal

MUX_CNTL IN (69K pull-down) Logic “0” (Mfgr.use) Control Signal

OPTION_3V OUT Regulated 3.0V Output

OEM ON-OFF IN (15K pull-down) Power On/Off External On/Off

3.6V±5% Max

MOD IN (22K pull-down) Programming signal 3V Max

BAT_VCC IN 3.6V iO1500R Power

RED_LED OUT Out-Of-Rrange indication 3V±2.5%

GREEN_LED OUT In-Range indication 3V±2.5%

BAT_GND IN Ground

20/5/03 page 10 of 37

Detailed Pins Descriptions

RS232 Standard Interface 8-Wire Or 4-Wire (Pin 1 through Pin 9)

This is a 3V DCE RS-232 interface. For ±9V use, OPTION_3V (Pin16) can supply power to an external level shifter IC like MAX3238E. The 9-volt external level shifter output can be connected to a PC COM port.

Audio Interface (Pins 10, 11 and 12)

These are future options of the iO1500R to provide audio communication.

Opt_Select_1 and Opt_Select_2 (Pin 13, Pin 14)

The option select lines set the communication state of the module. To support RS232 communication, the option select lines must be connected at one of three modes: “11” – Default mode via internal 22K pull up resistors. “01” – Option select 1 is externally pulled to ground. Diode – Anode to Pin 13 and cathode to Pin 14.

MUX_CNTL (Pin 15)

To use RS232, this pin must be held at logic low (facilitated by internal 69K pull down resistor).

OPTION_3V (Pin 16)

A regulated 3V output from the iO1500R with a maximum drive of 30 mA. This can be used to drive an external RS232 transceiver IC. Voltage is active only

when the OEM is ON.

OEM On-Off (Pin 17)

Used to power up and power down the iO1500R OEM. This is the recommended method for turning the iO1500R on and off and in vehicle applications it can be used as an ignition sense to power up. When this pin is connected to ground, the OEM will turn OFF. When this Pin is connected to BAT_VCC 3.6V, the OEM will turn ON.

MOD (Pin 18) This pin is internally pulled down via 22K resistor. Motorola recommends routing the MOD signal to an external connector. Should iO1500R software need to be updated, this pin must be available externally, or the flash cannot be programmed, and the iO1500R module will have to be removed from the product to reprogram it. Mod pulled to 3V at power up sets programming mode.

BATT_VCC (Pins 19 through 23) This is the 3.6 V iO1500R power supply. All should be driven by the same

source. Power: 3.6V ±5 % max., ripple 50mV. Input current: Avg. 1A, peak 2.5A.

Out-Of-Range indication, RED LED (Pin 24)

This OUTPUT is the Out Of Range Connection Status. It is a switched 3V output voltage with a maximum drive of 10 mA.

Solid Red light - OUT OF RANGE – iO1500R not connected to the iDEN network. Blinking Red light – iO1500R is registering or connecting to the iDEN network.

In-range indication-GREEN LED (Pin 25)

20/5/03 page 11 of 37

This OUTPUT is the In-Range Connection Status. It is a switched 3V output voltage with a maximum drive of 10 mA.

Blinking Green light - IN RANGE - the OEM is connected to the iDEN network. Solid Green light – The iO1500R is in use.

BAT_GND (Pins 26 through 30)

These pins are the ground return lines for the iO1500R and should be connected together with the same ground reference as the 3.6 V power supply for the iO1500R.

Status LED Indications

An on board single LED will be used for multi-purpose status indications as follows:

User Mode

LED State Indication

Alternating Red & Green

Flashing Red

Steady Red

Flashing Yellow

Flashing Green

Steady Green

A fatal error was detected during power-up:

- Flashstrap Fatal Error.

- Invalid Battery. Registering - your PC Card is registering to your carrier’s network. Please wait. No service -your PC Card can't register. It will continue trying to every two minutes as long as it is turned on. Unit registered - no packet data service. In service - your PC Card has successfully completed Packet Data registration. In use - your PC Card is currently being used

Voice Support

Audio input and output are supported on iO1500R:

• Audio input (from mic) on Zif connector pin 10

• Audio output (to speaker) on Zif connector pin 12

• PTT is supported via option select lines (Zif pins 13 and 14) Pulling both Opt

Select lines to ground indicates PTT to radio. Audio output impedance is 100-ohm. External Audio PA (high input impedance) is required. Nominal output is 64mVrms @ 1KHz. Audio input impedance is >39K-ohm. The audio source is expected to have output impedance of 100 ohms. Nominal audio input is 43.5mVrms. @ 1KHz

20/5/03 page 12 of 37

+ 25 hidden pages