(M) Logo MOTOROLA
120e CDMA
Generic User Guide
Final Approval Review
September 13, 2002
Part No. 6881043B17-O
Transcribed from Kit No. SJJN5034A
NOTICE
Motorola strives to make all our products accessible to as many
people as possible. Some features may not be accessible to everyone.
You may find that this phone has some features that are impractical
for people who are blind or visually impaired. We welcome your comments
about the accessibility of our products. Call Customer Care
1-800-331-6456, extension 255.
Transcribed and adapted by
Horizons for the Blind, Inc.
2 N. Williams St.
Crystal Lake, IL 60014
(815) 444-8800 Voice/TDD
(815) 444-8830 FAX
E-mail:
mail@horizons-blind.org
Web: horizons-blind.org
2003
###1 WELCOME
Welcome to the world of Motorola digital wireless communications!
We are pleased that you have chosen the Motorola 120e wireless phone.
Using the Alternate Format Manual:
This manual has been prepared from the original Motorola manual
SJJN5034A to offer as many options as possible for non-display use.
For these options, specific directions will be given regarding the
number of key presses to use for reaching a feature.
There are, however, some features that depend upon the display
for either use or setup. These features are designated as a DISPLAY
DEPENDENT FEATURE or DISPLAY DEPENDENT SETUP. In these cases,
directions will be given for display screen use only.
NOTE: In many cases, features that are designated as DISPLAY
DEPENDENT SETUP may be used without the display once the setup has
been completed.
KNOW YOUR PHONE
Before you start to use your phone, take time to examine it. The
phone is basically a rectangle with an antenna on the end.
Place the phone on a flat surface with the antenna at the top
right, and look over the phone. Various features are located along
the edges of the case as follows:
THE PHONE CASE:
Power Key: You will find the POWER KEY (PWR) along the curve of
the top left edge of the case.
Headset Jack: The HEADSET JACK is further around the curve under
the power key. Insert headset accessory.
Volume Keys: Continue following the case around the left edge
and you will find the VOLUME KEYS. These keys adjust earpiece and ringer
volume.
Voice Key: The VOICE KEY may be found at the right side edge,
opposite the level of the upper volume key. This key will allow you
to record voice notes, phonebook and shortcut names.
Accessory Connector Port: The ACCESSORY PORT is found at the
bottom edge of the case. Insert charger and phone accessories here.
The Battery Receptacle: The battery is placed in the back of the
phone. For details on the battery, see Installing the Battery on page
17.
THE PHONE FACE:
Earpiece: The area immediately under the front curve of the phone
is the EARPIECE. You may identify this area by the small ovals along
the surface.
Display: The smooth area near the top of the phone face is the
DISPLAY AREA. This area may arrive from the factory with a protective
plastic covering. This covering serves no function in the use of the
phone and may be removed by pulling on the tab. The small button above
the display case is a Motorola logo and this also serves no function
in the use of the phone.
The lower half of the case holds the major function areas for
operating your phone.
You will find a set of three keys beneath the display area. The
center key is the MENU key and the right and left keys are the Right
and LEFT "soft" keys.
--LEFT soft Key: Perform functions identified by left display
prompt, or use as directed in the text.
--Right soft Key: Perform functions identified by right display
prompt, or use as directed in the text.
--MENU: The MENU key is the main key for entering various menu
features.
End key: The END key is located under the LEFT soft key. It will
end phone calls and exit the menu system.
Send key: The SEND key is located under the Right soft key. It
will send and answer calls, and display recent dialed calls list.
Scroll Keys: The SCROLL KEYS are found under the MENU key. There
are two keys: an UPPER and Lower key. These keys are used to move through
menus and lists. Details for using the keys will be given within the
sections of the various features.
The bottom half of the phone face is a standard alphanumeric
keypad. From the top to the bottom, and left to right, these keys are
arranged as follows:
Microphone: The MICROPHONE is found in the area under the 0 and
Pound keys. ###2 Personal Communications Sector
600 North U.S. Highway 45
Libertyville, Illinois 60048
1-800-331-6456 (United States)
1-888-390-6456 (TTY/TDD United States)
1-800-461-4575 (Canada)
www.motorola.com (United States)
www.motorola.ca (Canada)
MOTOROLA, the Stylized M Logo and all other trademarks indicated
as such herein are trademarks of Motorola, Inc. (r) Reg. U.S. Pat.
& Tm. Off. TrueSync, Sidekick, Starfish, and the Stylized Starfish
Logo are registered trademarks of Starfish Software, Inc., a wholly
owned independent subsidiary of Motorola, Inc. All other product or
service names are the property of their respective owners.
(c) 2002 Motorola, Inc. All rights reserved.
SOFTWARE COPYRIGHT NOTICE
The Motorola products described in this manual may include
copyrighted Motorola and third party software stored in semiconductor
memories or other media. Laws in the United States and other countries
preserve for Motorola and third party software providers certain
exclusive rights for copyrighted software, such as the exclusive rights
to distribute or reproduce the copyrighted software. Accordingly, any
copyrighted software contained in the Motorola products may not be
modified, reverse-engineered, distributed, or reproduced in any manner
to the extent allowed by law. Furthermore, the purchase of the Motorola
products shall not be deemed to grant either directly or by implication,
estoppel, or otherwise, any license under the copyrights, patents,
or patent applications of Motorola or any third party software provider,
except for the normal, non-exclusive, royalty-free license to use that
arises by operation of law in the sale of a product.
Manual number: 6881043B17-O
###3 MENU MAP
Main Menu
Recent Calls
--Received Calls
--Dialed Calls
--Notepad
--Call Times
Phonebook
Datebook
Radio
Messages
--Voicemail
--Create Message
--Text Msgs
--Inbox
--Outbox
--Quick Notes
--Drafts
--Browser Alerts
Shortcuts
Voice Notes
Browser
Calculator
Games
--Settings (see page 4)
NOTE: This is the standard menu layout. You or your service
provider may have modified the menu structure or changed some feature
names. Not all features may be available for all users.
For example, the
when the FM Radio Headset accessory is plugged into the accessory
connector port on your phone. (See page 1 for a detailed phone
description.)
SHORTCUTS
Change display zoom: Press MENU, then press and hold MENU.
Lock/unlock keypad: Press MENU, STAR key.
Display my phone number: Press MENU, Pound key.
Go to dialed calls list: Press SEND.
Exit menu system: Press END. ###4 SETTINGS MENU
Ring Styles
--Style
--
--My Tones
PHONE STATUS
--My Tel. Number
--Active Line
--Battery Meter
--Other Information
BROWSER SETUP
CONNECTION
--Incoming Call
IN-CALL SETUP
Style
Detail
Radio
feature on the Main Menu is displayed only
--In-Call Timer
--Answer Options
SECURITY
--Phone Lock
--Lock Keypad
--Lock Application
--Restrict Calls
--New Passwords
LOCATION
--Location On
--911 Only
OTHER SETTINGS
--Personalize
Main Menu
Keys
Greeting
Banner
--Initial Setup
Time and Date
Auto PIN Dial
Auto Redial
Backlight
Zoom
TTY Setup
Scroll
Animation
Language
Contrast
DTMF
Master Reset
Master Clear
--Network
--Car Settings
--Headset
###5 CONTENTS
In this table of contents, the print page number is followed by
the braille page number. All page numbers in the text refer to print
page numbers.
MENU MAP ...................................................... 300
ABOUT THIS GUIDE ............................................ 10000
SAFETY AND GENERAL INFORMATION .............................. 11000
GETTING STARTED ............................................. 17000
What's in the Box? .......................................... 17000
Installing the Battery ...................................... 17000
Charging the Battery ........................................ 18000
Turning Your Phone On ....................................... 20000
Making a Call ............................................... 20000
Ending a Call ............................................... 21000
Answering a Call ............................................ 21000
Seeing Your Phone Number .................................... 21000
ABOUT YOUR PHONE ............................................ 22000
Using the Display ........................................... 22000
Zooming In and Out .......................................... 24000
###10 ABOUT THIS GUIDE
This user guide introduces you to the many features in your
Motorola wireless phone.
NAVIGATING TO A MENU FEATURE
Use the menu system to access your phone's features. This guide
shows you how to select a menu feature as follows:
NON-SCROLL NAVIGATION METHOD
To avoid scrolling through a display, detailed directions will
tell you how to reach a specific menu feature as follows:
IMPORTANT NOTE: In order to use these directions, the initial
setting for "Scroll" must be set to the "Wrap-Around" option. These
directions will not work if the "Scroll" setting is changed to
"Up/Down." See page 56 for details on the Scroll feature.
(Example)--To reach MESSAGES
START: Press MENU once: (Initial option)--
1. Press Right soft key to select.
2. The initial option offered will be
soft key to select. Text messages may then be entered by following
the display directions.
NOTE: All components of Text messaging are DISPLAY DEPENDENT.
3. Press END to return to the idle display when you have completed
the steps. Or, press END at any time to return to the idle display.
Detailed directions will not be given for features that are
DISPLAY DEPENDENT. For these features, directions will be presented
in the following manner:
Find the Feature:
Scroll menu path as follows--MENU,
This example shows that you must press MENU, scroll to and select
Messages
OPTIONAL FEATURE:
This label identifies an optional network or
subscription-dependent features that may not be offered by all service
providers in all geographical areas. Contact your service provider
for information about availability.
OPTIONAL ACCESSORY:
This label identifies an optional Motorola Original (tm)
accessory.
, then scroll to and select
Create Message
Create Message
Messages, Create Message
Messages
.
. Press Right
###11 SAFETY AND GENERAL INFORMATION
IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ THIS
INFORMATION BEFORE USING YOUR PHONE.
The information provided in this document supersedes the general
safety information contained in user guides published prior to July
2000. For information regarding radio use in a hazardous atmosphere
please refer to the Factory Mutual (FM) Approval Manual Supplement
or Instruction Card, which is included with radio models that offer
this capability.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
RF OPERATIONAL CHARACTERISTICS
Your phone contains a transmitter and a receiver. When it is ON,
it receives and transmits radio frequency (RF) energy. The phone
operates in the frequency range of 824 MHz to 849 MHz in analog and
digital mode and 1851.25 MHz to 1908.75 MHz in digital mode.
When you communicate with your phone, the system handling your
call controls the power levels at which your phone transmits. The output
power level typically may vary over a range from 0.05 watts to 0.54
watts in analog mode and 0.0 watts to 0.28 watts in digital mode.
EXPOSURE TO RADIO FREQUENCY ENERGY
Your Motorola phone is designed to comply with the following
national and international standards and guidelines regarding exposure
of human beings to radio frequency electromagnetic energy: ###12
--United States Federal Communications Commission, Code of
Regulations; 47 CFR part 2 sub-part J
--American National Standards Institute (ANSI)/Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992
--Institute of Electrical and Electronic Engineers (IEEE)
C95.1-1999 Edition
--National Council on Radiation Protection and Measurements (NCRP)
of the United States, Report 86, 1986
--International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998
--Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the Frequency
Range from 3 kHz to 300 GHz, 1999
--Australian Communications Authority Radiocommunications
(Electromagnetic Radiation-Human Exposure) Standard 1999
To assure optimal phone performance and make sure human exposure
to radio frequency electromagnetic energy is within the guidelines
set forth in the above standards, always adhere to the following
procedures:
PORTABLE PHONE OPERATION AND EME EXPOSURE
ANTENNA CARE:
Use only the supplied or an approved replacement antenna
Unauthorized antennas, modifications, or attachments could damage the
phone and may violate FCC regulations.
Do NOT hold the antenna when the phone is in use
antenna affects call quality and may cause the phone to operate at
a higher power level than needed.
PHONE OPERATION:
When placing or receiving a phone call, hold your phone as you
would a wireline telephone.
BODY-WORN OPERATION:
To maintain compliance with FCC RF exposure guidelines, if you
wear a phone on your body when transmitting, always place the phone
in a Motorola-supplied or approved clip, holder, holster, case, or
body harness for this product. Use of non-Motorola-approved
accessories may exceed FCC RF exposure guidelines. If you do not use
one of the Motorola-supplied or approved body-worn accessories, and
are not using the phone held in the normal use position,
antenna is at least one inch (2.5 centimeters) from your body when
transmitting
DATA OPERATION:
When using any data feature of the phone, with or without an
accessory cable,
centimeters) from your body
APPROVED ACCESSORIES:
For a list of approved Motorola accessories, visit our website
at www.motorola.com.
ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY
NOTE: Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded, designed,
or otherwise configured for electromagnetic compatibility.
FACILITIES:
To avoid electromagnetic interference and/or compatibility
conflicts, turn off your phone in any facility where posted notices
instruct you to do so. Hospitals or health care facilities may be using
equipment that is sensitive to external RF energy.
AIRCRAFT:
When instructed to do so, turn off your phone when on board an
aircraft. Any use of a phone must be in accordance with applicable
regulations per airline crew instructions. ###14 MEDICAL DEVICES
PACEMAKERS: The Health Industry Manufacturers Association
recommends that a minimum separation of 6 inches (15 centimeters) be
maintained between a handheld wireless phone and a pacemaker.
These recommendations are consistent with the independent
research by, and recommendations of, the United States Food and Drug
Administration.
Persons with pacemakers should:
--ALWAYS keep the phone more than six inches (15 centimeters)
.
position the phone antenna at least one inch (2.5
Speak directly into the microphone
.
. Holding the
. ###13
ensure the
.
from your pacemaker when the phone is turned ON.
--NOT carry the phone in the breast pocket.
--use the ear opposite the pacemaker to minimize the potential
for interference.
--turn OFF the phone immediately if you have any reason to suspect
that interference is taking place.
HEARING AIDS: Some digital wireless phones may interfere with
some hearing aids. In the event of such interference, you may want
to consult your hearing aid manufacturer to discuss alternatives.
OTHER MEDICAL DEVICES
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately shielded
from RF energy. Your physician may be able to assist you in obtaining
this information. ###15 SAFETY AND GENERAL USE WHILE DRIVING
Check the laws and regulations on the use of phones in the area
where you drive. Always obey them.
When using your phone while driving, please:
--give full attention to driving and to the road.
--use hands-free operation, if available.
--pull off the road and park before making or answering a call
if driving conditions so require.
OPERATIONAL WARNINGS
FOR VEHICLES WITH AN AIR BAG:
Do not place a portable phone in the area over an air bag or in
the air bag deployment area. Air bags inflate with great force. If
a portable phone is placed in the air bag deployment area and the air
bag inflates, the phone may be propelled with great force and cause
serious injury to occupants of the vehicle.
POTENTIALLY EXPLOSIVE ATMOSPHERES:
Turn off your phone prior to entering any area with a potentially
explosive atmosphere, unless the phone is a model specifically
identified as being "Intrinsically Safe." Do not remove, install, or
charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury
or even death.
NOTE: The areas with potentially explosive atmospheres referred
to above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
chemicals or particles such as grain, dust, or metal powders, and any
other area where you would normally be advised to turn off your vehicle
engine. Areas with potentially explosive atmospheres are often but
not always posted. ###16 BLASTING CAPS AND AREAS:
To avoid possible interference with blasting operations, turn
OFF your phone when you are near electrical blasting caps, in a blasting
area, or in areas posted: "Turn off two-way radio." Obey all signs
and instructions.
OPERATIONAL CAUTIONS
ANTENNAS:
Do not use any portable phone that has a damaged antenna
.
If a damaged antenna comes into contact with your skin, a minor burn
can result.
BATTERIES: All batteries can cause property damage and/or bodily
injury such as burns if a conductive material such as jewelry, keys,
or beaded chains touches exposed terminals. The conductive material
may complete an electrical circuit (short circuit) and become quite
hot. Exercise care in handling any charged battery, particularly when
placing it inside a pocket, purse, or other container with metal
objects.
###17 GETTING STARTED
WHAT'S IN THE BOX?
Your wireless phone typically comes equipped with a battery and
a charger. Other accessory options can customize your phone for maximum
performance and portability.
To purchase Motorola Original(tm) accessories, contact the
Motorola Customer Call Center at 1-800-331-6456 in the United States
or 1-800-461-4575 in Canada.
INSTALLING THE BATTERY
You must install and charge the battery to use your phone.
Your phone is designed to be used only with Motorola Original
batteries and accessories. We recommend that you store batteries in
their protective cases when not in use.
1. Remove the battery from its protective clear plastic case.
###18 2. If necessary, slide down the battery door release latch and
lift the door off of the phone.
3. Insert the battery, battery contacts first, into the top of
the battery compartment and push down.
4. Replace the battery door.
CHARGING THE BATTERY
New batteries are shipped partially charged. Before you can use
your phone, you need to install and charge the battery, as indicated
by the following instructions. Some batteries perform best after
several full charge/discharge cycles. ###19 1. Plug the travel
charger into your phone with the release tab facing up.
2. Plug the other end of the travel charger into the appropriate
electrical outlet.
3. DISPLAY FEATURE: When your phone indicates that the battery
is fully charged (
the travel charger.
NOTE: DISPLAY FEATURE--When you charge the battery, the battery
level indicator in the upper right corner of the display shows how
much of the charging process is complete. ###20 TURNING YOUR PHONE
ON
1. Press and hold PWR to turn on your phone.
2. If necessary, enter your four-digit unlock code and press OK
(Right soft key) to unlock your phone.
The unlock code is originally set to 1234. Your service provider
may change this number before you receive your phone.
MAKING A CALL
1. Press keypad keys to dial the phone number.
Tip: If you make a mistake, press DELETE (LEFT soft key) to delete
the last digit, or press and hold DELETE (LEFT soft key) to clear all
digits.
2. Press SEND to make the call ###21 ENDING A CALL
Press END to end the call.
ANSWERING A CALL
Charge Complete
), press the release tab and remove
When you receive a call, your phone rings and/or vibrates and
displays an incoming message.
--Press SEND or ANSWER (Right soft key) to answer the call.
Tip: If your phone is locked, you must unlock it to answer the
call.
DISPLAYING YOUR PHONE NUMBER
THIS IS A DISPLAY DEPENDENT FEATURE.
From the idle display:
Press MENU, Pound key to display your phone number.
###22 ABOUT YOUR PHONE
See page 1 for a detailed phone description.
USING THE DISPLAY
THIS IS A DISPLAY DEPENDENT FEATURE.
The
you are not on a call or using the menu.
Labels at the bottom corners of the display show the current soft
key functions. A MENU indicator at the bottom center of the display
indicates that you can press the MENU key to enter the main menu.
Some of the features shown in the idle display are described
below.
* Items shown with an asterisk are optional network and/or
subscription-dependent features. These features may not be offered
by all service providers in all geographical areas. Contact your
service provider for information about availability. ###23 1.
Signal Strength Indicator: Vertical bars show the strength of the
network connection. You cannot send or receive calls when the "no
signal" indicator is displayed.
* 2. Digital (D) or Analog (A) Signal Indicator: Shows whether
you are receiving a digital or analog signal.
3. In Use Indicator: Shows that a call is in progress.
* 4. Roam Indicator: Shows that your phone is seeking or using
another network system outside your home network.
* 5. Message Waiting Indicator: Appears when you receive a text
message.
* 6. Voice Message Waiting Indicator: Appears when you receive
a voicemail message.
7. Battery Level Indicator: Vertical bars show the battery charge
level. Recharge the battery when the
displayed, and/or you hear the low battery alert.
* 8. Active Line indicator: Shows the current active phone line.
9. Menu Indicator: Indicates that you can press MENU to enter
the main menu or open a feature sub-menu. ###24 10. Ring Style
Indicator: Icons show the ring style setting. Icons are DISPLAY
DEPENDENT: Consult the original print manual for an illustration of
the icons.
ZOOMING IN AND OUT
NOTE: THIS IS A DISPLAY DEPENDENT FEATURE.
Press and release MENU, then press and hold MENU to zoom in and
out on the display. Zoom in to increase text size, zoom out to display
more information.
You can also zoom in and out from the menu. See page 56.
ADJUSTING VOLUME
Press the up and down volume keys to:
--increase and decrease earpiece volume during a call
--increase and decrease the ringer volume setting when the idle
display is visible
BATTERY USE
Battery performance depends on many factors, including your
idle display
is the standard display that is displayed when
Low Battery
warning message is
wireless carrier's network configuration; signal strength; the
temperature at which you operate your phone; the features and/or
settings you select and use; and your voice, data, and other application
usage patterns. ###25 BATTERY CARE
CAUTION: To prevent injuries or burns, do not allow metal objects
to contact or short-circuit the battery terminals.
To maximize your battery's performance:
--Always use Motorola Original (tm) batteries and battery
chargers. The phone warranty does not cover damage caused from using
non-Motorola batteries and/or battery chargers.
--New batteries or batteries that have been stored for long
periods of time may require a longer charge time.
--Maintain the battery at or near room temperature when charging.
--Do not expose batteries to temperatures below -10 degrees C
(14 degrees F) or above 45 degrees C (113 degrees F). Always take your
phone with you when you leave your vehicle.
--When you do not intend to use a battery for a while, store it
uncharged in a cool, dark, dry place, such as a refrigerator.
--Over extended periods of time, batteries gradually wear down
and require longer charging times. This is normal. If you charge your
battery regularly and notice a decrease in talk time or an increase
in charging time, then it is probably time to purchase a new battery.
RECYCLE: The rechargeable batteries that power this product must
be disposed of properly and may need to be recycled. Refer to your
battery's label for battery type. Contact your local recycling center
for proper disposal methods. Never dispose of batteries in a fire
because they may explode. ###26 EXTENDING BATTERY LIFE
--Turn off the display backlight The backlight uses power. To
turn it off, see page "Initial Setup" on page 55.
--Minimize keypad-intense functions Activities that require
intensive keystroke use (such as playing a game or using messaging)
reduce your phone's talk and standby time. Lock the keypad when storing
the phone in your purse or pocket to avoid unnecessary keypad and
backlight activations. See page 139.
###27 MAKING AND ANSWERING CALLS
For basic instructions on how to make a call, end a call, and
answer a call, see pages 20-21.
REDIALING A NUMBER
If you hear an ordinary busy signal:
1. Press END to hang up.
2. Press SEND to redial the busy number.
USING AUTOMATIC REDIAL
If the network is busy, you hear a fast busy signal, and your
phone displays
With automatic redial, your phone automatically redials the
number for four minutes. When the call goes through, your phone rings
or vibrates one time, displays
the call.
You must turn on automatic redial to use the feature. See the
"Auto Redial" option on page 55. ###28 When automatic redial is
turned off, you can manually activate the feature to redial a phone
number. When you hear a fast busy signal and the display shows
Failed
--Press SEND or RETRY (Right soft key) to activate automatic
redial
USING CALLER ID
(OPTIONAL FEATURE)
Calling line identification
for incoming calls.
The phone displays the caller's name when the name is stored in
your phonebook, or
available.
RETURNING AN UNANSWERED CALL
Your phone keeps a record of your unanswered calls, and displays:
--the missed call indicator
-calls and Y is the number of missed calls with no caller ID information
1. Press VIEW (Right soft key) to display the received calls list.
2. Press SEND to select a call to return.
3. Press SEND to make the call. ###29 CALLING AN EMERGENCY NUMBER
Your service provider programs one or more emergency phone numbers,
such as 911, that you can call under any circumstances, even when your
phone is locked.
NOTE: Emergency numbers vary by country. Your phone's
preprogrammed emergency number(s) may not work in all locations, and
sometimes an emergency call cannot be placed due to network,
environmental, or interference issues.
1. Press keypad keys to dial the emergency number.
2. Press SEND to call the emergency number.
TURNING OFF A CALL ALERT
You can turn off your phone's incoming call alert before answering
:
X Missed Calls
Call Failed
Incoming Call
Y Unknown, where X is the total number of missed
.
Redial Successful
(caller ID) displays the phone number
when caller ID information is not
, and then connects
Call
the call.
--Press either volume key to turn off the alert.
CANCELING AN INCOMING CALL
While the phone is ringing or vibrating:
--Press END or IGNORE (LEFT soft key) to cancel the incoming call
###30 (OPTIONAL FEATURE)
Depending on your phone settings and/or service subscription,
the call may be forwarded to another number, or the caller may hear
a busy signal.
CALLING WITH SPEED DIAL
Each entry you store in your phonebook is assigned a unique
number. Press To speed dial a phonebook entry:
dial
1. Press keypad keys to enter the speed dial number for the entry
you want to call.
2. Press Pound key to submit the number.
NOTE: Some networks let you skip this step for speed dial numbers
1 through 99.
3. Press SEND to call the entry.
CALLING WITH ONE-TOUCH DIAL
To call phonebook entries 1 through 9, just press and hold the
one-digit speed dial number for one second.
We recommend that you reserve phonebook entry 1 (speed dial number
1) for storing and dialing your voicemail number. In many cases, your
service provider has already done this for you. If necessary, see page
66 to store your voicemail number for one-touch dial access. ###31
CALLING A NUMBER IN A TEXT MESSAGE
(OPTIONAL FEATURE)
NOTE: THIS IS A DISPLAY DEPENDENT FEATURE.
To call a phone number embedded in a text message that you receive:
1. Press MENU to open the
2. Press Scroll keys to scroll to
3. Press SELECT (Right soft key) to call the number.
ADDITIONAL CALLING FEATURES
NOTE: LIST SELECTIONS ARE DISPLAY DEPENDENT.
While dialing (with digits visible in the display), open the
Dialing Menu
--Press MENU,
or recent call lists
Press MENU,
in the To field ###32 You can also call a number using these
features:
--Press and release the voice key, then say a voice name to call
a phonebook entry using voice dial
To record a voice name, see page 69.
--DISPLAY OPTION: Press MENU,
Dialed Calls, entry to call
or dialed call
to perform the following tasks:
Attach Number
Send Message
to call a missed call, or a recent received
Text Msg Menu
Call Back
to attach a number from the phonebook
to open a new text message with the number
Recent Calls, Received Calls
.
.
speed
or
###33 USING FEATURES WHILE ON A CALL
USING CALL WAITING
(OPTIONAL FEATURE)
When you are on a call, an alert tone sounds to indicate that
you have received a second call.
1. Press SEND to answer the new call.
2. Press SEND to switch back to the first call.
MAKING A THREE-WAY CALL
(OPTIONAL FEATURE)
During a call, you can call and connect a third party for a
three-way call. You cannot do this if you already have a call on hold.
1. Press keypad keys to dial the third party's number.
NOTE: On some networks, you must press SEND first.
2. Press SEND to call the number.
3. Press SEND to connect the two calls.
4. Press END to end the entire call. ###34 ADDITIONAL ON-CALL
FEATURES
--Press MUTE (Right soft key) (if available) or scroll MENU,
to mute the call
--SPEAKER (Right soft key) (if available) or scroll MENU,
Spkrphone On
DISPLAY FEATURES:
--Scroll MENU,
--Scroll MENU,
tones, for credit card or password calls
To activate DTMF tones, see the "DTMF" option on page 57.
--Scroll MENU,
received or dialed call numbers
--Scroll MENU,
--Scroll MENU,
--Scroll MENU,
activate an attached speakerphone during an active call
My Tel. Number
Send Tones
Received Calls
Messages
Datebook
Other Information
to send a number to the network as DTMF
to display or send messages
to display datebook entries
to display your phone number
or
Dialed Calls
to display phone specifications
to display recent
Mute
###35 USING THE MENU
NAVIGATING TO A FEATURE
Use these keys to move through the menu system:
LEFT SOFT KEY: Perform the function shown in the lower left corner
of the display (usually EXIT or BACK).
MENU KEY: Enter the menu system, or open a sub-menu, when the
MENU icon is available in the bottom center of the display.
END KEY: Exit the menu system without making changes, return to
the idle display.
RIGHT SOFT KEY: Perform the function shown in the lower right
corner of the display (usually SELECT the highlighted menu item).
SCROLL KEY: Scroll up or down through menus and lists.
STAR AND POUND KEYS: Cycle through and set the value of the
highlighted menu item. ###36 SELECTING A FEATURE OPTION
Some features require you to select an item from a list:
In Display:
--Press BACK (LEFT soft key) to go back to the previous screen.
--Press MENU to open the sub-menu.
--Press VIEW (Right soft key) to view details of the highlighted
item.
--Press Scroll keys to scroll up or down to highlight the item
you want.
--In a numbered list, press a number key to highlight the item.
--In an alphabetized list, press a key multiple times to cycle
through the letters on the key and highlight the closest matching list
item. ###37 ENTERING FEATURE INFORMATION
NOTE: MOST COMPONENTS OF
Some features require you to enter information:
In Display:
--Press Scroll keys to scroll down to additional items.
--Press CANCEL (LEFT soft key) to exit without making changes.
DONE appears for the LEFT soft key when you enter or edit information.
Press DONE (LEFT soft key) to save your changes.
--Press CHANGE (Right soft key) to edit the selected information.
--Enter numbers or text with the keypad.
--When an item has a list of possible values, press Star or Pound
key to scroll through and select a value.
--When an item has a list of possible numeric values, press a
number key to set the value.
--If you enter or edit information and do not want to save your
changes, press END to exit without saving. ###38 The message
center lets you compose and send text messages. A flashing cursor shows
where text will appear:
In Display:
--
--Press CANCEL (Right soft key) to exit without making changes.
--Press MENU to open the sub-menu.
--Press BROWSE (Right soft key) to view and insert quick note.
When you enter text using the standard tap method, the flashing
cursor changes to a
Flashing cursor
indicates insertion point.
block cursor
FIELD
ENTRIES ARE DISPLAY DEPENDENT.
, and the soft key functions change:
In Display:
--
Block cursor
indicates current highlighted character.
After two seconds, the block cursor reverts to a flashing cursor
and moves to the next position.
--Press OK (Right soft key) to accept and store the text.
--Press DELETE (LEFT soft key) to delete the character to the
left of the insertion point.
###39 ENTERING TEXT
NOTE: ALL COMPONENTS OF TEXT MESSAGES ARE DISPLAY DEPENDENT.
Multiple text entry methods make it easy for you to enter names,
numbers, and messages on your phone.
CHOOSING A TEXT MODE
Press MENU from any text entry screen to select a text mode:
iTAP: Let the phone predict each word as you enter it. See page
44.
TAP METHOD: Enter letters, numbers, and symbols by pressing a
key one or more times. See page 40.
NUMERIC: Enter numbers only.
SYMBOL: Enter symbols only. See page 43.
BROWSE: Browse your phonebook or recent call lists to select a
name or number.
NOTE: The text mode you select remains active until you change
it by selecting another mode. ###40 USING TAP METHOD
This is the standard mode for entering text on your phone.
Press MENU from any text entry screen and select the Tap Method
menu option.
1. Press a number key one or more times to select a letter, number,
or symbol shown in the "Character Chart" on page 42.
2. Continue pressing number keys to enter the remaining
characters.
3. Press OK (Right soft key) to store the text when you are
finished. ###41 GENERAL TEXT ENTRY RULES
Press a number key repeatedly to cycle through its characters.
See "Character Chart" on page 42.
--Press a number key as many times as necessary to enter the
desired character at flashing cursor location.
--Press and hold a number key to cycle between text entry modes.
--Press Star or Pound key to move flashing cursor to the left
or right in text message.
--Use the Scroll keys to change letter in block cursor to
uppercase or lowercase.
--If you do not press a key for two seconds, the character in
the block cursor is accepted, and the cursor moves to the next position.
###42 --The first character of every sentence is capitalized unless
you manually override it. (Press Scroll keys down to force the character
to lowercase while it is highlighted by the block cursor.)
--Your phone may support multiple languages. The current language
setting determines whether a new message begins on the left or right
side of the display.
You can switch languages within a message. Press MENU to select
the text mode and language you want to use.
CHARACTER CHART
Use this chart as a guide for entering spaces, letters, numbers,
and symbols with the tap method.
1-key: Space, Period, 1, Question mark, Exclamation point, Comma,
"at" sign, Underscore, Ampersand, Tilde, Colon, Semicolon, Quotation
mark, Hyphen, Open parentheses, Close parentheses, Apostrophe, Opening
interrogation mark, Opening exclamation point, Percent sign, British
Pound-Sterling sign, Dollar sign, Yen sign, Currency symbol, Euro sign
2-ABC: a, b, c, 2, Diaeresis a, Ring a, Acute a, Grave a,
Circumflex a, Tilde a, alpha, beta, Cedilla c
3-DEF: d, e, f, 3, * Diaeresis e, Acute e, Grave e, Circumflex
e, epsilon, phi
4-GHI: g, h, i, 4, Diaeresis i, Acute i, Circumflex i, gamma,
eta, iota
5-JKL: j, k, l, 5, kappa, lambda
6-MNO: m, n, o, 6, Tilde n, Diaeresis o, Slashed o, Acute o, Grave
o, Circumflex o, Tilde o, mu, upsilon, omega
7-PQRS: p, q, r, s, 7, pi, German double-s, sigma
8-TUV: t, u, v, 8, theta, Diaeresis u, Acute u, Grave u, Circumflex
u, tau
9-WXYZ: w, x, y, z, 9, xi, psi
0-key: Plus sign, Minus sign, 0, Times sign, Asterisk, Slash,
Back slash, Open bracket, Close bracket, Equal sign, Greater than sign,
Less than sign, Number sign (Or Pound sign), Section mark
NOTE: This chart may not reflect the exact character set available
on your phone. ###43 USING SYMBOL MODE
Your phone provides an alternate way to enter symbol characters
in a message. Press MENU from any text entry screen and select the
Symbol menu option.
1. Press a number key one time to display its symbol options at
the bottom of the display. See "Symbol Chart" on page 43.
2. Press STAR or Pound key, or, press the number key multiple
times to highlight the symbol you want.
3. Press SELECT (Right soft key) to enter the symbol at the
flashing cursor location.
SYMBOL CHART
Use this chart as a guide for entering characters in symbol mode.
1-key: Space, Period, 1, Question mark, Exclamation point, Comma,
"at" sign, Underscore, Ampersand, Tilde, Colon, Semicolon, Quotation
mark, Hyphen, Open parentheses, Close parentheses, Apostrophe, Opening
interrogation mark, Opening exclamation point, Percent sign, British
Pound-Sterling sign, Dollar sign, Yen sign, Currency symbol, Euro sign
2-key: "At" sign, Underscore, Back slash
3-key: Slash, Colon, Semi=colon
4-key: Quote mark, Ampersand, Apostrophe ###44 5-key: Open
parentheses, Close parentheses, Open bracket, Close bracket, Open
brace, Close brace
6-key: Open interrogation sign, Open exclamation sign, Tilde
7-key: Less than sign, Greater than sign, Equal sign
8-key: Dollar sign, British Pound sterling sign, Yen sign
9-key: Pound sign, Percent sign, Asterisk
0-key: Plus sign, Minus sign, Multiplication sign, Asterisk,
Forward slash, Equal sign, Greater than sign, Less than sign, Pound
sign, Section mark
USING iTAP (tm) SOFTWARE PREDICTIVE TEXT ENTRY METHOD
iTAP (tm) software provides a predictive text entry method that
lets you enter a word using one keypress per letter.
Press MENU from any text entry screen and select the iTAP menu
option.
Enter Words
1. Press a number key one time to enter the first letter of the
word.
The letters associated with the key are shown at the bottom of
the display.
2. Press number keys (one per letter) to enter the rest of the
word.
Alternative words and letter combinations are shown at the bottom
of the display. The word choices are updated with each keypress. ###45
3. Press Star or Pound key to highlight the word you want.
4. Press SELECT (Right soft key) to enter the word at the flashing
cursor location. A space is automatically inserted after the word.
For example, to spell the word "act," press 2, 2, 8. The display
shows:
--Flashing cursor indicates insertion point.
--Press DELETE (LEFT soft key) to clear the last letter.
--Press Scroll key to scroll to and display additional word
choices.
--Press SELECT (Right soft key) to insert the highlighted word.
Enter Novel Words:
You may enter a word that the iTAP software does not recognize.
If the word you want is not displayed:
1. Press DELETE (LEFT soft key) one or more times to delete letters
until you see a letter combination that matches the start of the word.
###46 2. Press Star or Pound key to highlight the letter or letter
combination.
3. Press SELECT (Right soft key), then press Star key to shift
the text entry cursor to the left and "lock" the selected word portion.
4. Continue to enter letters and highlight letter combinations
to spell the word.
Punctuation:
Press 1 or 0 to enter punctuation or other characters as shown
in the "Character Chart" on page 42.
Capitalization:
The first word of a sentence is automatically capitalized, with
following words in lowercase.
Press Scroll keys up or down to change the words to initial
character capitalized, all uppercase characters, or all lowercase
characters. ###47 Enter Numbers:
1. Enter the first digit and then highlight it to put the iTAP
software in number entry mode.
2. Press number keys to add digits to the number.
3. Press SELECT (Right soft key) to enter the number at the
flashing cursor location.
Delete Letters and Words:
Place the cursor to the right of the text that you want to delete,
and then do the following:
Press DELETE (LEFT soft key) to delete one letter at a time.
Press and hold DELETE (LEFT soft key) to delete the entire
message.
###48 MENU FEATURE DESCRIPTIONS
This chapter describes all of your phone's features in order of
the menu map shown on pages 3-4.
MAIN MENU
NOTE: In the descriptions below, items will be shown under their
MAIN MENU directory. Detailed directions for reaching non-display
features will be shown on indicated pages. If no page number is given,
detailed directions for non-display features will be shown along with
the feature description.
Items below are in order of their appearance in the MAIN MENU
system. Sub-menus and sub-sub-menus are shown under the Main Menu
entry.
MAIN MENU
RECENT CALLS
NOTE: LIST SELECTIONS ARE DISPLAY DEPENDENT.
--RECEIVED CALLS: MENU,
Recent Calls, Received Calls
Display a list of recently received calls. See page 60.
--DIALED CALLS: MENU,
Recent Calls, Dialed Calls
Display a list of recently dialed calls. See page 60.
--NOTEPAD: MENU,
Recent Calls, Notepad
Call or store the last number entered on the keypad. See page
62.
--CALL TIMES (OPTIONAL FEATURE): MENU,
Recent Calls, Notepad
Display call timers that track time spent on your last call,
dialed calls, received calls, all calls since reset, and all calls
total. See page 62.
PHONEBOOK
MENU,
Phonebook
NOTE: MOST COMPONENTS OF
FIELD
ENTRIES ARE DISPLAY DEPENDENT.
Store names and numbers as entries in your phonebook, then call
numbers by selecting them from the phonebook list. See page 65. ###49
DATEBOOK
MENU,
Datebook
NOTE: ALL COMPONENTS OF THIS FEATURE ARE DISPLAY DEPENDENT.
Use the datebook calendar to schedule and review your appointments.
See page 74.
RADIO
MENU,
Radio
Listen to FM radio stations with the optional Motorola Original
(tm) FM Stereo Radio Headset accessory. This menu feature is displayed
only when the FM Stereo Radio Headset is plugged into the accessory
connector port on your phone. See page 79.
MESSAGES (OPTIONAL FEATURE)
MENU,
Messages
NOTE: MOST COMPONENTS OF THIS FEATURE ARE DISPLAY DEPENDENT *
* See information on Voicemail below.
Adjust message settings, display and manage the various types
of messages your phone can receive and/or send:
Loading...
+ 71 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.