Mossloo XJ0808 User Manual
Stick-On Stand
Bluetooth® Speaker
Instruction Manual
Functions:
1.
LED Indicator
2.
Micro-USB input port
3.
ON/OFF Switch
4.
Suction cups
What’s included:
1 x Bluetooth® Speaker
1 x USB to Micro-USB Charging Cable
1 x Instruction Manual
Tech Specications
•
Playing time: up to 1 hr at max volume
•
Charging time: up to 1.5 hr
•
Pairing Name: “Stick-On BT”
Instructions:
(Be sure to fully charge the speaker before
using for the rst time).
1.
Charging the Speaker
•
Connect the provided charging cable to a
power source and to the micro USB port on
the speaker (2).
The LED indicator light will glow red when
charging and turn off when fully charged.
2.
•
•
•
*
•
3.
•
SAFETY PRECAUTIONS:
•
1.
2.
3.
4.
5.
®
Setup:
Bluetooth
Turn ON/OFF switch to ON position, LED
Indictor will then ash BLUE.
Turn on the Bluetooth function on mobile
device, Select “Stick-On” pairing name.
LED will turn solid BLUE if successfully
paired
Speaker will automatically pair if the mobile
device has been paired before.
Turn ON/OFF switch to OFF position to
turn off the device
Suction Cups:
Use the suction cups to secure the
bluetooth speaker to any at surfaced
object (e.g. Your phone or tablet)
WARNING-When using this product, basic
precautions should always be followed:
Read all the instructions before use.
Never store or use this product in
temperatures below 32°F(0°C) or above
115°F(45°C).
The unit’s full performance is achieved
only after 2 or 3 completed charge and
discharge cycles.
To reduce the risk of injury, close
supervision is necessary when the product
is used near children.
Do not expose the device to moisture.
6.
Do not use the device in excess of its
output rating. Overload outputs above
rating may result in a risk of re or injury.
7.
Do not use the device if damaged or
modied.
8.
Damaged or modied batteries may exhibit
unpredictable behavior resulting in re,
explosion or risk of injury.
9.
Do not disassemble the device. For
repairs, seek a qualied service
professional. Incorrect reassembly may
result in a risk of re or injury.
10.
Do not expose the device to re or
excessive temperature. Exposure to re
or temperatures above 104°F may cause
explosion.
11.
Ensure that qualied service professionals
use only identical replacement parts to
ensure product safety
MADE IN CHINA
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure condition
without restriction.
Loading...