Mossloo MSL W6011Q User Manual

Light Up Logo Speaker

w/ Wireless Charging

Powerbank

Instruction Manual: 7197-29

Functions:

1.

Wireless Charging Surface

2.

Light-up panel

3.

Bluetooth LED indicator

4.

ON/OFF Button

5.

Wireless Charging LED

6.

Wireless Charging Button

7.

Powerbank LED indicator

8.

Micro-USB Input

9.

USB Output

What’s included:

1 x Bluetooth Speaker (7197-29)
1 x USB to 2Amp Micro-USB Charging Cable
1 x Instruction Manual

Tech Specications

Playing Time: up to 7hrs at max volume

•
Charge Time: 2hrs (from 0-100%)

•
Pairing Name: Light Up Speaker

•
Battery: 2000mAh

•
Micro-USB Input: 5V/2A

•
USB Output: 5V/2A

•
Wireless Output: 5V/1A 5W

•.

Instructions:

(Be sure to fully charge the speaker before

using for the rst time).

Charging the Speaker:

1.

Connect the provided charging cable to a

•
power source and to the micro USB port(8)

on the speaker.
The Powerbank LED indicator (7) will ash

•
RED when charging, and will turn solid RED

when fully charged.

Bluetooth® Setup:

2.

Press and hold ON/OFF Button(4)

•
to turn ON the speaker, Bluetooth LED

indicator(3) will ash BLUE when in
bluetooth standby mode.

Turn on the Bluetooth function on

•
mobile device, Select Light Up Speaker

pairing name. LED will turn solid BLUE if
successfully paired.

Speaker will automatically pair if the mobile

•

device has been paired before.

Press and hold ON/OFF Button(4) to turn off

•

the device.

Using the Speaker:

3.

Press the ON/OFF Button(4) button to

•

pause music and again to play.

When receiving a phone call, press the ON/

•
OFF Button(4) button to answer and again

to hang up.
Long press to reject the call.

•

Double press to redial the last call.

•

Charging mobile phones and other

4.

electronic devices:

Connect the charging cable to your mobile

•
phone/device using the appropriate

connector.

Connect the USB A Part of the cable into the

•
USB Output(9), Powerbank LED Indicator(7)

will turn RED when charging.

Remove the USB cable from your mobile

•

device when it is fully charged.

Wireless Charging Function:

5.

Press the Wireless Charging Button(6)

•

to turn on the wireless charging function.

The Wireless Charging LED(5) will glow

GREEN.

Place the wireless charging supported

•
device on the Wireless Charging Surface,
LED(5) will glow RED when device is

charging.

Long press the Wireless Charging

•

Button(6) to turn off Wireless Charging.

** Note: If the Wireless Charging LED is

ashing an unknown object is being detect­ed between the wireless charging surface
and the phone by FOD(Foreign Object
Detection). The device will not begin to
charge until object is removed.**

SAFETY PRECAUTIONS:

WARNING-When using this product, basic

•
precautions should always be followed:

Read all the instructions before use.

1.

Never store or use this product in

2.

temperatures below 32°F (0°C) or above

115°F (45°C).
Do not overcharge Phone. Unit may get

3.
hot with excessive use. Remove Phone
when it is fully charged. Never charge for
more than 7 hours at a time.

The unit’s full performance is achieved

4.

only after 2 or 3 completed charge and

discharge cycles.
Keep out of reach of children.

5.

Do not use the device in excess of its

6.
output rating. Overload outputs above
rating may result in a risk of re or injury.

Do not use the device if damaged or

7.
modied.
Damaged or modied batteries may exhibit

8.
unpredictable behavior resulting in re,
explosion or risk of injury.
Do not disassemble the device. For

9.
repairs, seek a qualied service
professional. Incorrect reassembly may
result in a risk of re or injury.
Do not expose the device to re or

10.

temperatures above 104°F may cause

explosion.
Ensure that qualied service professionals

11.

use only identical replacement parts to

ensure product safety.

Attachments on the back of your phone

12.

can impede the effectiveness of the

wireless charger, and lead to overheating.

Please remove attachments from the

phone before charging on this device.

FCC Statement:

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:
This device may not cause harmful

(1)

interference, and
This device must accept any interference

(2)

received, including interference that may

cause undesired operation.

Warning:

*

Changes or modications not expressly

approved by the party responsible for
compliance could void the user’s authority

to operate the equipment.

MADE IN CHINA