Mossloo MSL W25Q User Manual
Fleet 10W Fast Wireless
Charging Stand Kit
Instruction Manual
7141-82
1
2
Features:
Wireless Charging Surface
1.
2.
LED Indicator
Micro USB Input
3.
4.
UL Listed QC 3.0 AC Adapter
What’s included:
1 x Wireless Charging Stand
1 x Micro-USB to USB Cable
1 x Instruction Manual
1 x UL Listed QC 3.0 AC Adapter
Input: DC 5V/2A/9V/2A(MAX)
•
•
Wireless Output: 5W/7.5W/10W
INSTRUCTIONS:
Wireless Charging Function:
•
Connect the Micro-USB to USB cable(incl.)
with the AC adaptor(4) to a power source.
Once connected the LED indicator will flash
•
three times then turn into solid blue(left side）
indicating the device is on standby mode is
ready to begin charging.
•
Place the wireless charging supported
device on the charging surface(1), the
will begin to charge automatically.
device
LED indicator(on the right side) will glow
3
4
RED when device is charging.
Note: When wireless charging, if the LED
**
indicator(on the right side) is flashing RED
the device is either NOT a wireless charging
device or there is an object between the
deviceand charging surface interfering with
the charging process.
To achieve fast wireless charging,
providedQC 3.0 AC adapter is required.
SAFETY PRECAUTIONS:
WARNING-When using this product, basic
•
precautions should always be followed:
Read all the instructions before use.
1.
Never store or use this product in
2.
temperatures below 32°F (0°C) or above
115°F (45°C).
Do not overcharge your phone. The unit
3.
may become hot under excessive use.
Remove your phone once it is fully charged.
Never charge your phone for more than 7
hours at a time.
To reduce the risk of injury, close
4.
supervision is required when the product is
used near children.
Do not expose the device to moisture.
5.
Do not use the device in excess of its
6.
output rating. Overload outputs above the
7.
Do not use the device if damaged or
8.
explosion or risk of injury.
9.
Do not disassemble the device. For repairs,
Incorrect reassembly may result in a risk of
10.
or temperatures above 104°F (40°C) may
result in explosion.
To ensure product safety, ensure that
11.
identical replacement parts.
Attachments on the back of your phone can
12.
impede the effectiveness of the wireless
charger, and lead to overheating. Please
remove attachments from the phone before
charging on this device.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
inaccordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception,which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum 20cm distance between the
radiator your body: Use only the supplied antenna
MADE IN CHINA
Loading...