Page 1
RN330009MUK Rev2
* Register online for your 2 year guarantee. See back of this instruction book for details. (UK and Ireland customers only)
www.morphyrichards.co.uk/blog
For competitions, product hints and tips
and more join us at
www.facebook.com/morphyrichardsuk
@loveyourmorphy
IMPORTANT: To prevent limescale problems which would not be covered by
the guarantee, we recommend the use of a mix of 50% tap water and 50%
distilled or demineralised water (available from most large supermarkets).
Multi-function Steam Generator
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 1
Please read and keep these instructions for future use
Page 2
2
Personal safety
• CAUTION - HOT: Burns can
occur from touching hot
parts, hot water or steam,
or the iron rest plate.
• WARNING: Never direct steam at
electrical components or fittings. If in
doubt about the suitability of steam
for cleaning an appliance, contact
the appliance manufacturer for
advice prior to cleaning.
• WARNING: Never touch the plug or
cable with wet hands.
• WARNING: Nozzles and tools will be
hot after use. Allow to cool before
attempting to remove.
• WARNING: Do not discharge the
steam towards people or animals.
Danger of scalding.
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
•
WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
•
This appliance can be used by persons with
reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, if they have
been given supervision or instruction concerning
the use of the appliance in a safe way and
understand the hazards involved.
•
Children shall not play with the appliance.
•
Keep the appliance out of reach of children when it
is energized or cooling down.
•
The steam generator must not be left unattended
while it is connected to the supply mains.
•
The steam generator must be used and rested on
a stable surface.
•
When placing the iron on the steam generator base
or on its heel, ensure that the surface on which the
heel or base is placed is stable.
•
The steam generator is not to be used if it has been
dropped, if there are visible signs of damage or it
is leaking.
•
The filling aperture may be opened during use, due
to the design of the system.
STEAM
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 2
Page 3
3
Health and safety ................................................................................................
Electrical requirements .......................................................................................
Dual functionality ................................................................................................
Steam ironing overview / Features ....................................................................
Temperature guide ..............................................................................................
Safe working for ironing ......................................................................................
Before use ...........................................................................................................
Using the steam generator for steam ironing ....................................................
Filling ...................................................................................................................
Features ...............................................................................................................
Steam cleaning mode (certain models only) .....................................................
Steam cleaning accessories overview (certain models only) ...........................
Steam cleaning floors (certain models only) .....................................................
Using the accessories for steam cleaning (certain models only) .....................
Attachments for use with the accessory adaptor (certain models only) .........
Utility nozzle for use on the jet nozzle (certain models only) ............................
After use ..............................................................................................................
Maintenance .......................................................................................................
Emptying and storing .........................................................................................
Contact us ...........................................................................................................
Guarantee ............................................................................................................
Contents
2 & 3
3
4
4
5
6
6
6 & 7
8
8
9
9
10 & 11
12
13
13
14
14
15
15
16
• To protect against fire, electric
shock and personal injury, do not
immerse cord, plug or steam
generator in water or other liquid.
• The plug should be removed from
the wall socket after use, before
cleaning, filling or changing the
accessories, or carrying out user
maintenance.
Location
• Do not use or keep this product
outside.
• Do not store the appliance near hot
surfaces eg. ovens or heating
appliances.
Mains cable
• WARNING: A damaged or severed
mains cable fitted with a plug
should never be connected to the
mains supply. It must be
destroyed, as a damaged cable
becomes hazardous if connected
to a power socket.
• Do not let the mains lead come into
contact with the hot soleplate of the
iron.
• Do not allow the mains lead to
become strained.
Product safety
• Do not operate with a damaged
steam/supply cord or grommet, it
must be replaced by the manufacturer,
its service agent or similarly qualified
person in order to avoid a hazard.
• WARNING: Always test on an
inconspicuous area first. Never use
on materials that can not resist
high temperature, such as dralon,
natural fur etc.
•
Never modify the appliance in any
way.
Other safety considerations
• Do not use any chemical
detergents, perfumes, alcohol or
descaler etc in water.
• Repairs to electrical appliances are
only to be undertaken by trained
personnel.
• Unprofessional repairs can be
dangerous for users.
• Use only genuine Morphy Richards
spare parts and accessories.
• The appliance must not be left
unattended while connected to the
supply mains.
• This appliance is intended for
domestic use only. Misuse or use
for commercial or any other purpose
will render the guarantee invalid.
Electrical requirements
• Check that the voltage on the rating
plate of your appliance corresponds
with your house electricity supply
which must be A.C. (Alternating
Current).
• If the socket outlets in your home
are not suitable for the plug
supplied with this appliance, the
plug should be removed by trained
authorised personnel and the
appropriate one fitted.
• WARNING: This appliance must be
earthed.
•
Should the fuse in the mains plug
require changing, a 13 amp BS1362
fuse must be fitted.
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 3
Page 4
4
Dual functionality
Dependant on the model, this product can be
easily used for two separate functions:
1
Steam generator iron for use with an ironing
board for ironing clothes, linen etc.
2
On certain models, a range of attachments can
be added to enable the product to be used as
a steam cleaner for cleaning floors, carpets,
work surfaces, glass and vertical or hard to
reach surfaces (see ‘Steam cleaning mode’
section, page 9).
Features
(1) Water tank
(2) Water tank filler cap
(3) Iron handle
(4) Iron steam trigger
(5) Temperature dial
(6) Soleplate
(7) Iron release button
(8) Iron steam supply cord
(9) Iron cable grommet
(10) Iron heel
(11) Temperature indicator light
(12) Locking hook
(13) Locking column
(14) Iron rest plate
(15) Iron rear docking hook
(16) Steam generator main body
(17) Control panel
(18) Power cord
(19) Water tank release button
(20) Water tank handle
(21) Cord storage groove
(22) Cord clamp
(23) Steam cord connection inlet
(24) Spring-loaded steam
connection inlet cover
(25) Iron steam cord connector
release buttons
(26) Iron steam cord connector
(27) Steam pressure indicator
(28) Power indicator
(29) Descaling indicator
(30) Low water indicator
(31) On/Off power button
(32) High steam indicator
(33) Medium steam indicator
(34) Low steam indicator
(35) Steam level selector
Steam ironing mode overview
3
4
5
6
8
10
9
1 2
2
19
20
12 13 14
21 22
15
17
23 24
26 825
18
16
27
17
7
11
21 22
23 24
2625
27
17
28
31
30
29
8
26
32
35
34
33
18
24
Steam ironing Steam cleaning
(certain models only)
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 4
Page 5
5
Heat setting markings on the temperature dial of all Morphy Richards irons match those of the International
Textile Care Labelling Code
Symbol
(120°C Max) Cool (160°C Max) Warm (210°C Max) Hot MAX setting
Control dial
positions
Do not iron
• •• •••
Fabric Nylon, Acetates,
synthetic fabrics
Wool, Polyester
mixtures
Cotton, Linen
Rayon, Rayon
mixtures
Ironing Iron on wrong side,
if moisture
required, use
damp cloth
(not Acetate)
Fabrics requiring
this setting usually
require steam
pressing.
Steaming
Without steam
Steam level setting
(see step 6 of
‘Using the Steam
Generator for
steam ironing’,
page 7)
No steam
(see ‘Dry ironing’,
page 8)
Low Medium / High High
Temperature guide
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 5
Page 6
6
Locate your steam generator horizontally on the
iron rest plate of your ironing board (if large
enough) or on a heat resistant stand at the same
height as your ironing board or below it. Always
ensure the steam generator is on a firm surface
when ironing.
WARNING: Do not use the product on a
surface which could be damaged by heat or
steam such as a worktop or a polished wood
surface.
If in doubt, contact Morphy Richards.
Remove any protective cover from the soleplate
(6) and the base unit, if any.
Unwind and straighten the power cord
(18) and
steam supply cord
(8).
Textiles and clothes should carry ironing
instructions. If not, follow the temperature guide
on the previous page, but test the temperature by
ironing the hem of the garment or similar discreet
area first.
It is advised to begin with ‘cool’ fabrics and work
up to higher settings. An iron heats up quicker
than it cools down so you’ll save time and
electricity.
If you turn the temperature dial down from a hot
setting to a cooler setting, wait until the iron
temperature has stabilised before you continue
ironing.
NOTE: Hold the steam generator main body
(16)
with both hands when handling and moving the
unit, as the water tank (1) is detachable.
Safe working for ironing
Before use
Unlock the iron from its storage position on top
of the steam generator main body (16) by
pressing and holding the iron release button (7) this unlocks the iron, enabling you to rotate the
tip of the soleplate (6) (in an anti-clockwise
direction) out from under the locking hook (12).
Lift the iron heel (10) away from the rear docking
hook (15).
WARNING: Never press down on the locking
column
(13)
itself to unlock it, incase the iron
is already on and the soleplate is hot.
During use, the iron may be rested on the iron
rest plate (14) with the soleplate tip on top of the
locking hook and the heel slotted on to the rear
docking hook.
If steam ironing, ensure the iron steam supply
cord (8) is attached into the steam cord
connection inlet (23) on the back of the steam
generator main body (16).
The steam cord connection inlet can be found by
opening the spring-loaded steam connection
inlet cover (24).
Open the spring-loaded steam connection inlet
cover and push the steam cord connector (26)
(with the two screw heads in the casing facing
upwards) firmly into the steam cord connection
inlet until it clicks into place.
Using the steam generator for steam ironing
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 6
1
2
Page 7
7
7
Turn the temperature dial (5) to suit the garment
(see ‘Temperature guide’, page 5). The
temperature indicator light (11) illuminates until
the temperature is reached. Begin ironing when
the temperature indicator light goes out. If you
turn the temperature dial down, wait until the
temperature indicator light illuminates and then
goes off again.
The temperature indicator will cycle on and off
during ironing as it maintains its temperature.
4
Press the steam level selector button (35) to
select the desired steam level. The relevant
steam level indicator (32/33/34) will stop
flashing and illuminate constantly when the
steam level is reached.
For a strong, continuous flow of steam during
ironing, press and hold the iron steam trigger
(4)
to deliver steam through the soleplate (6).
NOTE: During use, the number displayed on the
steam pressure indicator
(27) will change. This
will not interfere with how you use the product
or how it performs.
WARNING: The steam supply cord
(8)
will get
hot during use.
Plug the appliance into a mains outlet and press
the On/Off power button (31) to activate the unit.
A buzzer will be heard, the power indicator (28)
will illuminate and the low steam indicator (34)
will flash.
Remove the detachable water tank (1) by
squeezing the water tank release button (19). Lift
the filler cap (2), and fill with water to the max fill
line. Replace the water tank.
Using the Steam Generator for steam ironing (continued)
When you have finished ironing, turn off the
appliance by pressing and holding the On/Off power
button
(31) for two seconds. A buzzer will be heard
and both the power indicator (28) and steam level
indicator (32/33/34) will be extinguished.
Disconnect the plug from the mains outlet.
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 7
3
5
4
6
4
6
7
Page 8
8
IN HARD WATER AREAS, WE RECOMMEND A
MIX OF 50% TAP WATER AND 50%
DISTILLED OR DEMINERALISED WATER.
Never use battery topping up fluid or water
containing any substances like starch, sugar,
fragrant additives or defrosted water from a
refrigerator.
Re-filling during use
If the water level is too low, the low water level
indicator (30) will illuminate, a buzzer will sound,
and the unit will not produce steam. If this
happens, disconnect the water tank (1) by
squeezing the water tank release button
(19). Lift
the filler cap (2) and refill with water to the max
fill line. Replace the water tank.
Dry ironing
To use your steam generator as a dry iron only,
follow steps 1, 2, 4 and 5 of ‘Using the Steam
Generator for steam ironing’ on pages 6 and 7.
You do not need to put water in the water tank or
select a steam level. Press
the iron steam trigger
(4) at least once every 10 minutes, or the product
will automatically turn off.
Auto shut-off (certain models only)
If
the steam trigger
(4) is unused for 10 minutes,
the product will automatically turn off, both for
safety and to save energy.
To restart, press the On/Off power button
(31)
(see step 2 of ‘Using the Steam Generator for
steam ironing’ on page 6) and wait for the
temperature to rise again.
Steam function
During steaming, small amounts of water may be
ejected from the soleplate
(6)
. This is normal and
can be avoided by using the steam for short
amou
nts of time and only when the iron is at the
correct temperature (the temperature indicator
light (11) on the iron goes out when ready).
Sudden jolts of the boiler unit can also cause
water droplets on the soleplate; therefore, do not
move the base unit during ironing. We
recommend for first time ironing that you iron
over an old towel.
NOTE: The product may occasionally produce a
pumping sound during steam ironing. This is
normal and is caused by water being pumped
through the steam generator.
Vertical steam
Vertical steam is useful for removing creases from
hanging clothes, curtains, wall hangings, etc.
Hold the iron between 1cm and 2cm away from
the item and press the iron steam trigger
(4)
.
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
Features
Filling
4
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 8
4
Page 9
9
IMPORTANT: Please remember that the steam cleaner operates by emitting steam at an increased
temperature of over 100oC. Always test on an inconspicuous area first. Never use it on objects or
surfaces which cannot resist this temperature, or on surfaces with coatings or polishes, or on delicate
materials such as dralon, plastic, natural fur or antique items etc.
If in doubt, check carefully on a part of the material where minor marks will not matter.
(36) Jet nozzle child lock
(37) Jet nozzle steam trigger
(38) Jet nozzle
(39) Accessory storage box lid
(40) Accessory storage rack
(41) Accessory storage box
(42) Jet nozzle steam supply cord
(43) Steam cord connector
release button (jet nozzle)
(44) Steam cord connector (jet
nozzle)
(45) Accessory adaptor
(base attachment for circular
brush attachments
(48)
and
spatula attachment
(47)
, see
page 13)
(46) Utility nozzle
(base attachment for
elasticated utility cloths
(50)
and squeegee attachment
(49)
, see page 13)
(47) Spatula attachment
(to remove stubborn
deposits, see page 13)
(48) Circular brush attachments
(for tiles, wheel trims, mirrors
etc, see page 13)
(49) Squeegee attachment
(for tiled or glass areas such
as windows or mirrors etc,
see page 13)
(50) Elasticated utility cloths
(for tiled or glass surfaces,
upholstery and bedding etc,
see page 13)
(51) Extension tubes
(52) Floorhead attachment
(for carpets or hard floors,
see pages 10 and 11)
(53) Carpet glider
(for carpets, see page 11)
(54) Micro-fibre floor cloth
tightening toggle
(55) Micro-fibre floor cloth
(for carpets or hard floors,
see page 11)
(56) Wheeled floor base
(for carpets or hard floors,
see page 11)
Steam cleaning accessories overview (certain models only)
8
26
18
24
39
41
40
4443
37
36
38
46
49
48
45
47
50
51
52
53
56
42
55
54
Steam cleaning mode (certain models only)
The accessories shown below are only available with certain
models only.
Therefore, any information relating to their use (particularly
pages 10, 11, 12 and 13) are relevant for certain models only.
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 9
Page 10
10
Steam cleaning floors (certain models only)
Ensure the jet nozzle child lock (36) is in the
locked position.
Then, attach the jet nozzle steam supply cord
(42) into the steam cord connection inlet (23) on
the back of the steam generator main body (16).
The steam cord connection inlet can be found by
opening the spring-loaded steam connection
inlet cover (24).
Open the spring-loaded steam connection inlet
cover and push the steam cord connector (with
the two screw heads in the casing facing
upwards) firmly into the steam cord connection
inlet until it clicks into place.
Remove the iron (providing it has been allowed
to cool following any previous usage) from its
locked storage position on top of the steam
generator main body (16) (as described in step 2
of ‘Using the steam generator for steam ironing’).
Next, unplug the appliance from the mains
supply outlet.
Remove the iron steam supply cord (8) from the
steam cord connection inlet (23) by squeezing
the steam cord connector release buttons (25)
on the top and bottom of the steam cord
connector (26) and pull the ironing steam supply
cord out of the unit. Set the iron aside in a safe
place on its heel.
Attach both extension tubes
(51) together by
pushing the screw-threaded top end of one tube
onto the ‘D’ shaped bottom end of the other
tube. The upper tube has a screw-lock which
must be tightened as indicated on the tubes to
secure them together.
Attach the tube assembly to the jet nozzle
(38)
using the same method as described above.
Attach the floorhead attachment (52) to the base
of the tube assembly by pushing the screwthreaded neck of the floorhead onto the ‘D’
shaped bottom end of the lower tube. The tube
has a screw-lock which must be tightened as
indicated on the neck of the floorhead
attachment to secure them together.
IMPORTANT: Before use, hardfloors should be thoroughly swept and carpets should be thoroughly dry
vacuumed. However, we recommend that the steam cleaner is not used on:
• bare wooden floors or any surfaces where wood is exposed (as it will absorb moisture and may distort).
• damaged hardfloors or hardfloors with gaps present (as it will absorb moisture and may distort).
Also, do not steam in one place for an extended period, because the continual heat may cause damage
to carpets and laminate flooring.
Please disconnect and allow the unit to cool before changing cloths and attachments.
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 10
1
2
3
4
Page 11
11
If cleaning carpet, rest the floorhead attachment
(52) with the micro-fibre floor cloth (55) attached
into the carpet glider (53) to make it easier to
move the floorhead attachment across the
carpet.
NOTE: The carpet glider is designed to make it
easier to move the floorhead across the carpet
and is intentionally a loose fit on the floorhead.
Attach the micro-fibre floor cloth (55) to the
floorhead attachment (52), securing it in place by
tightening the toggle (54).
Steam cleaning floors (certain models only) (continued)
Fill the water tank (1). Reconnect the appliance
to the mains supply outlet. Turn the product on
and select the steam level as described in steps
3, 4 and 6 of ‘Using the steam generator for
steam ironing’, page 7.
Ensure the jet nozzle child lock
(36) is in the
unlocked position, this will allow you to use the
jet nozzle steam trigger (37) to produce steam
as required.
When you have finished steaming, turn off the
appliance as described in step 7 of ‘Using the
steam generator for steam ironing’, page 7.
To allow easy manoeuvring around the floor, rest
the steam generator main body (16) into the
wheeled floor base (56).
NOTE: The wheeled floor base is designed to
make it easier to move the steam generator
across the floor when using the floorhead
attachment and is intentionally a loose fit on the
steam generator.
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 11
5 6
7
8
Page 12
12
This function is ideal for cleaning vertical
surfaces and hard to reach places.
Attach the jet nozzle
(38) to the steam generator
main body (16) as described in steps 1 and 2 of
‘Steam cleaning floors’, page 10.
In order to use the circular brush attachments
(48) or the spatula attachment (47), the
accessory adaptor (45) must firstly be attached
onto the jet nozzle (38). This can be done by
completing the following:
Push the screw-threaded wide opening of the
accessory adaptor onto the ‘D’ shaped end of
the jet nozzle. The jet nozzle has a screw-lock
which must be tightened as indicated on the
accessory adaptor to secure them together.
Push the accessory (the circular brush
attachments
(48) or the spatula attachment (47))
onto the end of the accessory adaptor (45) by
aligning the large circular protrusion on the
accessory adaptor with the corresponding large
key-way inside the hole of the accessory, and the
smaller circular protrusion on the accessory
adaptor with the corresponding smaller key-way
inside the hole of the accessory. Then, twist the
accessory until it locks into place.
If wishing to use the utility nozzle
(46), this may be
attached to the jet nozzle using the same method
as attaching the accessory adaptor.
Using the accessories for steam cleaning (certain models only)
If additional reach is required, one or both of the
extension tubes (51) may be used between the jet
nozzle (38) and the accessory adaptor (45) or the
utility nozzle
(46).
Attach the extension tube(s) into the end of the jet
nozzle as described in step 3 of ‘Steam cleaning
floors’, page 10.
Push the screw-threaded wide opening of the
accessory adaptor or utility nozzle onto the ‘D’
shaped end of the tube. The tube has a screw-lock
which must be tightened as indicated on the
accessory adaptor or utility nozzle to secure them
together.
NOTE: steam cleaning mode has been designed
for one-handed use.
WARNING: Switch OFF and unplug before
changing accessories. After use, accessories will
be very hot, allow to cool before handling.
WARNING: Never direct steam towards people,
animals or delicate surfaces. When using in the
steam cleaning mode, only ever hold the product by
the jet nozzle handle.
Never block any nozzle, eg. by holding against a
surface being cleaned.
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 12
1
3
2
Page 13
Utility nozzle (46)
Required for using the squeegee and upholstery functions.
Push the screw-threaded wide opening of the utility nozzle onto the ‘D’ shaped end of the jet
nozzle
(38) or extension tube(s) (51). The jet nozzle or extension tube(s) have a screw-lock
which must be tightened as indicated on the utility nozzle to secure them together.
13
Utility nozzle for use on the jet nozzle (certain models only)
Attachments for use with the accessory adaptor (certain models only)
Accessory adaptor (45)
• Adaptor for other accessories.
•
Clean crevices.
•
Hard to reach places.
Spatula attachment (47)
•
Remove stubborn deposits.
• De
-ice the freezer.
Circular brush attachments (48)
•
Remove stains on tiles.
• Clean
wheel trims.
• Clean ovens
and hobs.
•
Clean grout.
45
48
Attach the squeegee attachment to the utility
nozzle (46) by inserting the lip at the front of the
utility nozzle under the small hooks at the front of
the recess in the squeegee attachment. Then
secure the back of the utility nozzle into the
locking clip on the squeegee attachment.
Remove the squeegee attachment after use by
holding the locking clip away. The utility nozzle
can now be lifted out of the squeegee
attachment.
Elasticated utility cloth (50)
Use this cloth for covering the utility nozzle (46)
to clean or freshen up:
• Glass surfaces
• Upholstery
• Bedding
43
46
Squeegee attachment (49)
Use this attachment for cleaning:
• Tiles • Shower Doors • Windows • Mirrors
WARNING: Do not use on very cold glass, as the sudden temperature change may crack the glass.
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 13
46
50
Page 14
14
Follow the two maintenance steps below after
every use.
1. Switch the cleaner off and unplug from the
socket. If the appliance was used as a steam
cleaner, place immediately on a suitable sur face
(eg. tiled floor) where the residual heat/moisture in
the floor nozzle/cloth will not affect the surface.
Wait until the cleaner has cooled down
completely.
2. Remove the detachable water tank (1) by
squeezing the water tank release button (19). Lift
the filler cap (2), and empty the water tank.
Cleaning the boiler
When the boiler requires descaling, the descaling
indicator (29) will illuminate. When this happens,
the boiler must be manually rinsed out with clean
water until all the scale is removed. The indicator
light will go out only after the scale has been
removed.
WARNING: Never remove the boiler screw
(58)
when the steam generator is hot.
1
Unplug the appliance from the mains outlet and
leave to cool for two hours.
2
Remove the detachable water tank (1).
3
Remove the iron by disconnecting the iron steam
supply cord
(8) from the steam cord connection
inlet (23) (see step 1 of ‘Steam cleaning floors
(certain models only)’, page 10).
4
Hold the steam generator main body (16) firmly
with both hands and shake well.
5
Turn the steam generator main body upside-down
and pull back the boiler cap (59). Unscrew the
boiler screw
(58) with the boiler key (57), which is
attached to the underside of the steam generator
main body. If the screw is a bit too tight to undo,
try using a large screwdriver or a socket and
wrench set for more leverage.
6
Hold the steam generator main body over the
sink, turn it the correct way up to empty all water
and loose scale from the boiler into the sink.
7
Using clean water, refill and empty the boiler
repeatedly until all scale has been rinsed out.
8
Replace the boiler screw, ensuring it is tightened
fully. Replace the boiler cap, boiler key, water tank
and iron to the base unit.
WARNING: Ensure the boiler is empty before
replacing the boiler screw.
9
The descaling indicator will extinguish the next
time you use the product. Please wait for up to
one minute whilst it pumps water and registers
that the boiler has been cleaned.
To clean a coated soleplate (6)
Do not use scouring powder or solution as this
could cause damage to the coating.
If any man-made fibres fuse to the soleplate, set
the iron at the MAX position and pass it over a
clean piece of cotton to draw the deposit off the
surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp
cloth and mild detergent, then wipe dry. Abrasive
cleaners should not be used.
Cleaning the cloths (certain models only)
The micro-fibre floor cloth (55) and the
elasticated utility cloths (50) can be machine
washed (40ºC max). For heavy soiling, soak the
cloths in warm water and detergent or a mild
stain remover.
IMPORTANT: Do not use bleach or fabric
softener.
Allow cloths to completely dry before storing.
Replacement cloths can be purchased by calling
our UK helpline directly on: 0844 873 0726 or
logging onto www.morphyrichards.com.
Maintaining the attachments (certain
models only)
Dirt and blockages should be regularly removed
from the attachments to help prolong their usage.
After use
Maintenance
57
58 59
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 14
57
58 59
Page 15
15
Allow the appliance to cool.
Remove the detachable water tank
(1) by
squeezing the water tank release button (19). Lift
the filler cap
(2), and empty the water tank. Once
the water tank is empty, re-attach it to the steam
generator main body (16).
If the steam generator is not going to be used for
a long time, also empty the boiler as instructed,
(see ‘Cleaning the boiler’, page 14).
To store, pull the cord clamp (22) outwards. Wrap
the power cord (18) and iron steam supply cord (8)
around the base unit in the cord storage groove (21).
Secure the cord in place with the cord clamp. Avoid
kinking of cables, particularly at the exit from the
steam generator main body
(16)
.
IMPORTANT: Do not pull too tightly on the iron
cable grommet (9), or the iron steam supply
cord (8) where it joins the iron steam cord
connector (26), when wrapping the power cord
(18) around the steam generator main body
(16). Damage to cables caused by wrapping
too tightly will not be covered by the
guarantee.
Storing the steam iron
Lock the iron into the storage position on top of
the steam generator main body by pushing the
soleplate down on the locking column
(13) whilst
pushing the iron heel (10) onto the rear docking
hook (15). The iron should now be at a slight
diagonal on the iron rest plate. Pivot the tip of the
soleplate (6) under the locking hook (12) and off
the locking column. The spring-loaded locking
column will now spring up, securing the iron in
place.
Attach the iron steam supply cord
(8) into the
steam cord connection inlet (23) on the back of
the steam generator main body (16), as described
in step 1 of ‘Using the steam generator for steam
ironing’, page 6.
Storing the accessories (certain models
only)
Store all accessories in the accessory storage
rack (40) and place into the accessory storage
box (41) and fit the lid (39) securely to the box.
Helpline
If you are having a problem with your appliance,
please call our Helpline, as we are more likely to
be able to help than the store you purchased the
item from.
Please have the product name, model number
and serial number to hand when you call to help
us deal with your enquiry quicker.
UK Helpline: 0844 871 0960
IRE Helpline: 1800 409 119
Spares: 0844 873 0726
Talk To Us
If you have any questions or comments, or want
some great tips to help you get the most out of
your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Contact us
Emptying and storing
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 15
Page 16
RN330009MUK Rev2 12/13
Your standard 1 year guarantee is extended for an
additional 12 months when you register the product within
28 days of purchase with Morphy Richards. If you do not
register the product with Morphy Richards within 28 days,
your product is guaranteed for 1 year. To validate your 2
year guarantee, register with us online at
www.morphyrichards.co.uk
Or call our customer registration line
UK 0844 871 0962
IRE 1800 409 119
N.B. Each qualifying product needs to be registered with
Morphy Richards individually.
Please note that the 2 year guarantee is only available
in the UK and Ireland. Please refer to the 1 year guarantee
for more information.
To qualify for the 1 year guarantee, the appliance must
have been used according to the instructions supplied.
It is important to retain the retailer’s receipt as proof of
purchase. Staple your receipt to this back cover for future
reference.
Please quote the following information if the product
develops a fault. These numbers can be found on the base
of the product.
Model no. Serial no.
All Morphy Richards products are individually tested before
leaving the factory. In the unlikely event of any appliance
proving to be faulty within 28 days of purchase, it should
be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months (2
years if registered) of original purchase, you should contact
the Helpline number quoting Model number and Serial
number on the product, or write to Morphy Richards at the
address shown.
You may be asked to return a copy of proof of purchase.
Subject to the exclusions set out below (see Exclusions),
the faulty appliance will then be repaired or replaced and
dispatched usually within 7 working days of receipt.
If you suspect a fault, follow the simple checks detailed
below before retrying the appliance or calling the helpline.
• Check the steam outlet is not blocked.
• Check the plug is firmly in the socket.
• Check the socket is working by trying another appliance.
• Check the fuse in the plug.
If, for any reason, this item is replaced during the 1 year
guarantee period, the guarantee on the new item will be
calculated from original purchase date. Therefore it is vital
to retain your original till receipt or invoice to indicate the
date of initial purchase.
This appliance is intended for domestic use only. Misuse
or use for commercial or any other purpose will render the
guarantee invalid.
Morphy Richards shall not be liable to replace or repair the
goods under the terms of the guarantee where:
1 The fault has been caused or is attributable to accidental
use, misuse, negligent use or used contrary to the
manufacturer’s recommendations or where the fault has
been caused by power surges or damage caused in transit.
2 The fault is caused by limescale build-up.
3 The cables are damaged due to wrapping too tightly or
excessive kinking.
4 The appliance has been used on a voltage supply other
than that stamped on the products.
5 Repairs have been attempted by persons other than our
service staff (or authorised dealer).
6 The appliance has been used for hire purposes or non
domestic use.
7 The appliance is second hand.
8 Morphy Richards reserves the right not to carry out any
type of servicing under the guarantee at its discretion.
9 The guarantee excludes consumables such as cloths and
brushes.
• This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for
consequential loss or damage. This guarantee is offered
as an additional benefit and does not affect your statutory
rights as a consumer. Morphy Richards products are
intended for household use only. See usage limitations
within the location safety instructions.
Morphy Richards has a policy of continuous improvement
in product quality and design. The company, therefore
reserves the right to change the specification of
its models at any time.
For electrical products sold within the
European Community. At the end of the
electrical products useful life, it should not be
disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority
or retailer for recycling advice in your country.
Exclusions
Registering your 2 year
guarantee
Your 1 year guarantee
Disclaimer
The After Sales Division
Morphy Richards Ltd
Mexborough,
South Yorkshire,
England, S64 8AJ
IF YOU ARE HAVING A PROBLEM
WITH ONE OF OUR PRODUCTS,
CALL OUR HELPLINE:
UK: 0844 871 0960
EIRE: 1800 409 119
SPARES: 0844 873 0726
RN330009MUK Rev2_Instruction Book 11/12/2013 14:57 Page 16
Loading...