Steam Generator with
Purchase spare anti-scale cartridges to keep your product performing like
new for longer. Available by calling our Spares Helpline on 0344 873 0710.
RN333300 MUK Rev3
* Register online for your 2 year guarantee. See back of this instruction book for details. (UK and Ireland customers only)
Please read and keep these instructions for future use
IMPORTANT: To reduce limescale problems which would not be covered by the
guarantee, we recommend the use of a mix of 50% tap water and 50% distilled,
deionised or demineralised water (available from most large supermarkets).
Never use battery topping up fluid or water containing any substances like
starch, sugar, fragrant additives or defrosted water from a refrigerator.
Remember to clean your steam generator and change the antiscale cartridge.
Failure to adhere to the above guidelines will invalidate your guarantee.
IF YOU HAVE ANY DIFFICULTY WITH THIS PRODUCT,
INSTEAD OF TAKING IT BACK TO THE RETAILER, TRY:
1. The instruction booklet 2. Refer to www.morphyrichards.com
3. Or call our helpline: UK: 0344 871 0944, EIRE: 1800 409 119 (For UK & Eire customers only)
Register your guarantee online: www.morphyrichards.co.uk/support
We'll keep you updated with special offers, competitions and important product information.
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 1
2
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
•
WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
•
This appliance can be used by persons with reduced
physical, sensory or mental capabilities, or lack of
experience and knowledge, if they have been given
supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards
involved.
•
Children shall not play with the appliance.
•
Keep the appliance out of reach of children when it is
energized or cooling down.
•
The steam generator must not be left unattended
while it is connected to the supply mains.
•
The steam generator must be used and rested on
a stable surface.
•
When placing the iron on the steam generator base
or on its heel, ensure that the surface on which the
heel or base is placed is stable.
•
The steam generator is not to be used if it has been
dropped, if there are visible signs of damage or it
is leaking.
•
The filling aperture may be opened during use, due
to the design of the system.
•
Do not operate with a damaged steam/supply
cord or grommet, it must be replaced by the
manufacturer, its service agent or similarly qualified
person in order to avoid a hazard.
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 2
3
Health and safety ............................................................................
Electrical requirements ...................................................................
Steam generator overview / Features ............................................
Control panel overview ...................................................................
Temperature guide ..........................................................................
Location ...........................................................................................
Before first use ................................................................................
Using the steam generator ............................................................
Features ...........................................................................................
Maintenance ....................................................................................
Emptying and storing ......................................................................
Contact us .......................................................................................
Guarantee ........................................................................................
Contents
2
3
4
5
6
6
6
7 & 8
9
9 & 10
11
11
12
Personal safety
•
CAUTION - HOT: Burns
can occur from
t
ouching hot parts, hot
water or steam, or the
i
ron rest plate.
•
WARNING: Misuse of the
appliance could cause personal
i
njury.
•
WARNING: Never direct steam at
electrical components or fittings.
I
f in doubt about the suitability of
steam for cleaning an appliance,
contact the appliance
m
anufacturer for advice prior to
cleaning.
• WARNING: Never touch the plug
or cable with wet hands.
• WARNING: Nozzles and tools will
be hot after use. Allow to cool
before attempting to remove.
• WARNING: Do not
discharge the
steam towards
people or
animals.
Danger of
scalding.
•
To protect against fire, electric
shock and personal injury, do not
immerse cord, plug or steam
generator in water or other liquid.
• The plug should be removed from
the wall socket after use, before
c
leaning, filling or changing the
accessories, or carrying out user
m
aintenance.
Location
• Do not use or keep this product
o
utside.
• Do not store the appliance near hot
s
urfaces eg. ovens or heating
appliances.
Mains cable
• WARNING: A damaged or severed
m
ains cable fitted with a plug
should never be connected to the
mains supply. It must be
destroyed, as a damaged cable
becomes hazardous if connected
to a power socket.
• Do not let the mains lead come into
contact with the hot soleplate of the
iron.
• Do not allow the mains lead to
become strained.
Product safety
• WARNING: Always test on an
inconspicuous area first. Never
use on materials that can not
resist high temperature, such as
dralon, natural fur etc.
•
Never modify the appliance in any
way.
Other safety considerations
• D
o not use any chemical
detergents, perfumes, alcohol or
d
escaler etc in water.
• Repairs to electrical appliances are
only to be undertaken by trained
p
ersonnel.
• U
nprofessional repairs can be
dangerous for users.
• Use only genuine Morphy Richards
s
pare parts and accessories.
• The appliance must not be left
unattended while connected to the
s
upply mains.
• T
his appliance is intended for
domestic use only. Misuse or use
f
or commercial or any other
purpose will render the guarantee
invalid.
Electrical requirements
• Check that the voltage on the rating
plate of your appliance corresponds
with your house electricity supply
which must be A.C. (Alternating
Current).
• If the socket outlets in your home
are not suitable for the plug
supplied with this appliance, the
plug should be removed by trained
authorised personnel and the
appropriate one fitted.
• WARNING: This appliance must
be earthed.
•
Should the fuse in the mains plug
require changing, a 13 amp BS1362
fuse must be fitted.
STEAM
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 3
4
(1) Steam supply cord
(2) Cable support
(3) Iron handle
(4) Steam trigger
(5) Iron
(6) Soleplate
(7) Iron heel
(8) Control panel (see page 5)
(9) Iron rear docking hook
(10) Iron rest plate
(11) Iron-to-base lock
(12) Filling cap
(13) Detachable water tank
(14) Power cord
(15) Antiscale cartridge
(16) Antiscale cartridge drawer
(17) Base unit
(18) Cord storage clip
(19) Water tank removal tabs
Steam generator overview
1 2 43
5
6
15
16
11
13
12
1 14
109
1817 19
8
7
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 4
5
Control panel (8) overview
Select button (20)
Continue to press the select button until the
desired temperature setting is reached.
No steam indicator (21)
This illuminates when the 1 dot temperature
setting is selected. The low temperature is not
suitable for steaming.
Temperature setting indicators
(22/23/24/25)
The temperature indicators correspond with the
International Textile Care Labelling Code as shown
on the labels of your garments (see ‘Temperature
guide’ on page 6).
Steam level indicators (26/27/28)
The steam level is automatically adjusted to suit
the selected temperature setting. The steam level
indicators change when you select your desired
temperature setting.
Antiscale indicator (29)
When the antiscale cartridge requires changing,
the antiscale indicator will illuminate. This indicator
will flash if the antiscale cartridge is not fitted
properly.
Auto shut-off indicator (30)
This indicator illuminates if the appliance has
entered auto shut-off mode after not being used
for 10 minutes.
IntelliTemp setting indicator (31)
This illuminates when the product has reached the
default temperature, allowing the appliance to iron
all ironable fabrics without the temperature
needing to be adjusted.
Self Clean indicator (32)
This indicator will illuminate when the system
requires cleaning.
Low water indicator (33)
This indicator will illuminate when there is
insufficient water in the tank to produce steam.
2
0
21 22
29 30 31 3332
27
28
26
23 24 25
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 5
6
Locate the steam generator horizontally on the
iron rest plate of your ironing board (if large
enough) or on a heat resistant stand at the same
height as your ironing board or below it. Always
ensure the steam generator is on a firm surface
when ironing.
WARNING: Do not use the product on a
surface which could be damaged by heat or
steam such as a worktop or a polished wood
surface.
If in doubt, contact Morphy Richards.
Remove any protective covers from the soleplate
(6) and the base unit (17).
Unwind and straighten the power
(14) and steam
supply cords (1).
Remove the antiscale cartridge
(15) from the
antiscale cartridge drawer (16) and immerse in
water for 5 minutes for better filtration. Insert
cartridge back into the antiscale cartridge drawer.
The first time you use the iron or insert a new
cartridge, hold the trigger for up to two minutes to
pull the steam through to the soleplate.
Textiles and clothes usually carry ironing
instructions. If not, follow the temperature guide
above, but test the temperature by ironing the
hem of the garment or other discreet area first.
It is advised to begin with ‘cool’ fabrics (see
above) and work up to higher settings. An iron
heats up quicker than it cools down so you’ll save
time and electricity.
If you turn the temperature level down from a hot
setting to a cooler setting, wait until the
temperature setting indicator
(22/23/24/25/31)
stops flashing (indicating the correct temperature
has been reached) before you continue ironing.
You can carry the appliance by the iron handle
(3)
once the iron (5) is locked to the base unit (17)
using the iron-to-base lock (11) (see ‘Storing the
steam iron’ on page 11).
Lo
catio
n
Bef
or
e first us
e
H
eat setting markings on the temperature dial of all Morphy Richards irons match those of the International
Textile Care Labelling Code
Temperature guide
S
ymbol
(
120°C Max) Cool (160°C Max) Warm (210°C Max) Hot MAX setting
Temperature level
settings
Do not iron
• •• •••
Fabric Nylon, Acetates,
synthetic fabrics
Wool, Polyester
mixtures
Cotton, Linen
Rayon, Rayon
mixtures
Ironing Iron on wrong side,
if moisture
required, use
damp cloth
(not Acetate)
Fabrics requiring
this setting usually
require steam
pressing.
Steaming
Without steam
Steam level setting
(
see step 4 of
‘Using the Steam
Generator’ on
p
age 7)
No steam
(
see ‘Dry ironing’
on page 9)
Low Medium / High High
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 6
7
Alternatively, the water tank may be filled
without removing it from the base unit (17).
Simply open the filling cap (12), and fill the
water tank with water to the max fill line.
1a) Removing and filling the water tank 1b) Filling the water tank in situ
Remove the detachable water tank (13) using the
water tank removal tabs (19), open the filling cap
(12), and fill with water to the max fill line. Replace
the water tank.
IN HARD WATER AREAS, WE RECOMMEND A
MIX OF 50% TAP WATER AND 50% DISTILLED,
DEIONISED OR DEMINERALISED WATER.
Never use battery topping up fluid or water
containing any substances like starch, sugar,
fragrant additives or defrosted water from a
refrigerator.
NOTE: Please see point 2 of ‘Exclusions’ on page 12.
Re-filling during use
If the water level is too low, the low water indicator
will illuminate and the unit will not produce steam.
If this happens, refill the detachable water tank
(13) with water.
If a different temperature than IntelliTemp
setting is required to suit the garment (see
‘Temperature guide’ on page 6), you may adjust
the temperature as follows: press the select
button (20) repeatedly until the required
temperature setting indicator (22/23/24/25) is
displayed. Pressing the select button cycles the
options as shown in the next step.
2) Default IntelliTemp Setting 3) Temperature Selection
Plug the appliance into a mains outlet to switch
the product on. A beep will be heard and the
IntelliTemp logo (31) will illuminate on the control
panel (8). The default temperature is the
IntelliTemp setting, this allows the appliance to
iron all ironable fabrics without the temperature
needing to be adjusted. However, do not iron
any fabric with this symbol . The Intellitemp
setting indicator (31) will stop flashing and
remain constant when the IntelliTemp setting is
reached.
Using the Steam Generator
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 7
8
Using the Steam Generator (continued)
The steam function is ideal for relaxing the fibres
of tougher fabrics (like jeans and linen) and getting
rid of those stubborn, hard to reach creases.
To produce a steam boost during ironing, simply
double-press the steam trigger
(4). To deactivate
the boost, press once on the steam trigger again.
The appropriate steam level indicator will flash
whilst the steam trigger is pressed, indicating that
steam is being produced.
NOTE: steam cannot be produced on the 1-Dot
setting - this is highlighted by the no steam
indicator
(21) being visible on the control panel (8)
whilst the 1-Dot setting is selected.
When using the steam function and replacing the
iron
(5) back onto the iron rest plate (10), residual
steam may create condensation on the base. This
is not the iron leaking and is normal.
ALLOW TO COOL
6) Steam boost
When you have finished ironing, disconnect the
plug from the mains outlet
.
NOTE: The product may occasionally produce a
pumping sound during steam ironing. This is
normal and is caused by water being pumped
from the water tank to the steam generator. If
the pumping sound suddenly becomes louder
or the steam diminishes, check and refill the
water tank if it has become empty.
7) Switching off
IntelliTemp
setting
Dot 1 Dot 2
Dot 3Max
4) Temperature and steam level
The appropriate temperature setting indicator
(22/23/24/25/31) will flash until the desired
temperature is reached. Begin ironing when the
temperature indicator illuminates constantly. If you
turn the temperature down, wait until the temperature
indicator stops flashing before continuing ironing.
The steam level is automatically adjusted to suit the
selected temperature setting. This is denoted by the
steam level indicators (26/27/28) on the control panel
(8), which will change along with the temperature
setting indicators when you select your desired
temperature level. Press and hold the steam trigger
(4)
for constant steam.
5) Unlocking the iron
Unlock the iron (5) from its storage position on top
of the base unit
(17) by rotating the iron-to-base
lock
(11) - this enables you to lift the iron heel (7)
away from the iron rear docking hook (9).
During use, the iron may be rested on the iron rest
plate
(10) with the iron-to-base lock rotated so the
flat side is upper-most (in the unlocked position).
4
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 8
9
Dry ironing
T
o use your steam generator as a dry iron only,
follow steps 2, 3, 4 and 5 of ‘Using the Steam
Generator’ on page 7 and 8. You do not need to
p
ut water in the water tank
(
13)
.
Auto shut-off
If
the steam trigger
(4) is not used for 10 minutes,
t
he product will automatically turn off for safety
and to save energy. When this happens, the auto
shut-off indicator
(30) will flash.
To restart,
press the select button
(20) and wait
for the temperature to rise again.
NOTE: The appliance is not turned off completely
in auto shut-off mode. To switch the product off,
unplug the product from the mains outlet.
Steam function
D
uring steaming, small amounts of water may be
ejected from the soleplate
(6)
. This is normal and
can be avoided by using the steam for short
a
mou
n
ts of time and only when the iron is at the
correct temperature (the temperature setting
i
ndicator
(
22/23/24/25/31)on the control panel
s
tops flashing when ready).
S
udden jolts to the boiler unit can also cause
water droplets on the soleplate; therefore, do not
move the base unit
(17) during ironing.
We recommend for first time ironing that you
iron over an old towel.
Vertical steam
Vertical steam is useful for removing creases
from hanging clothes, curtains, upholstery, etc.
Hold the iron
(5)
between 1cm and 2cm away
from the item and press the steam trigger
(4)
twice in quick succession for a longer boost of
steam. To turn the steam boost off, press the
steam trigger again.
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
4
Fe
a
t
ure
s
The product requires an antiscale cartridge to
help reduce limescale and extend its life. The
antiscale indicator (29) will illuminate to prompt
you to replace the antiscale cartridge which is
located in the base unit (17) behind the water tank
(13). The antiscale indicator (29) will go out only
after the antiscale cartridge has been replaced.
Maintenance
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 9
10
Replacing the antiscale cartridge (15)
1
T
he appliance must be plugged in and switched
ON whilst changing the cartridge, otherwise
t
he antiscale indicator (29) will not go out.
2
Remove the water tank (13) from the base unit
(
17)by holding the tabs on the side of the water
tank and pulling the tank away from the base unit.
C
AUTION: The cartridge may be very
h
ot. Be careful when releasing the old
cartridge.
3
Grasp the grip on the front of the cartridge drawer
(16) and pull it out from the base unit. Lift the old
cartridge out of the drawer and dispose of it.
4
Remove the new anti-scale cartridge (15) from
the bag and immerse in water for 5 minutes for
better filtration.
5
Place the new antiscale cartridge into the
cartridge drawer and push the drawer back into
the base unit until it clicks into place.
6
Push the water tank back into the base unit until
it clicks into place.
7
Hold the steam trigger (4) for up to two minutes
to pull the water through the antiscale cartridge
and out through the soleplate (6) as steam.
NOTE: If no antiscale cartridge is installed, or the
antiscale cartridge is not installed correctly, the
antiscale indicator will continue to flash and the
appliance will not work correctly.
Self clean
The self clean function removes scale and
minerals which have built-up in the steam
chamber. This function must be performed every
time the self clean indicator (32) illuminates.
C
AUTION: Boiling hot water and lots of steam
will drain from the holes in the soleplate during
self clean. Position yourself comfortably near a
s
ink before you start. The self clean process
will take up to 5 minutes to complete. Do not
p
l ace the iron back on the base until the self
clean process has completed.
1
F
ill the water tank (13)(see step 1 of ‘Using the
Steam Generator’ on page 7).
2
P
ress and hold the select button (20)and steam
trigger
(4) and hold them both for 3 seconds. A
beep will be heard and the self clean indicator
(32) will flash, showing the product is ready to
begin self cleaning. Release the select button and
steam trigger.
3
Hold the iron (5) at approximately 15 centimetres
above an empty sink in the horizontal ironing
position.
4
Water containing loose scale and minerals will be
ejected through the holes in the iron’s soleplate
(6).
NOTE: Self clean cannot be aborted until the
process is complete.
5
Once self clean is complete, the iron will resume
at the previous ironing setting and your previous
temperature setting indicator (22/23/24/25/31)
will display on the control panel (8).
6
Iron over a damp cloth to remove any deposits on
the soleplate, this will also remove any water
marks that may have formed on the soleplate.
7
Turn off the product (see step 7 of ‘Using the
Steam Generator’ on page 8).
To clean a coated soleplate
Do not use scouring powder or solution as this
could cause damage to the coating.
If any man-made fibres fuse to the soleplate
(6),
set the iron at the MAX setting and pass it over a
clean piece of cotton to draw the deposit off the
surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp
cloth and mild detergent, then wipe dry.
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 10
11
A
llow the appliance to cool.
Remove the detachable water tank (13). Open the
f
iller cap (12), and empty the water tank. Once the
water tank is empty, re-attach it to the base unit
(17)
.
Storing the steam iron
Lock the iron (5) into the storage position on top
o
f the base unit (17)as follows:
1
Ensure the iron-to base lock (11) is in the
unlocked position (flat side facing upwards).
2
Push the iron heel (7) into the rear docking hook (9)
and rest the soleplate (6) on the iron rest plate (10).
3
Ensure the tip of the soleplate is pointing to the
arrow on the flat side of the iron-to-base lock. Then
rotate the iron-to-base lock through 180º around
the tip of the soleplate, securing the iron in place.
4
A
ttach the cord storage clip(18)to either side of
the base unit
(17)
by pushing the nodules on the
lower part of the clip into the holes on the
u
nderside of the base unit.
5
Straighten any kinks in the steam supply cord (1)
and the power cord (14). Next, loosely loop the
cords together in a figure 8 formation and fix them
in position in the cord storage clip
(18). Ensure
there is slack on the cables at the base unit end,
and on the steam supply cord at the cable support
(2) on the iron (5).
WARNING: Do not wrap the cables too tightly
as this can stress and damage the wires inside.
Damage to the cables caused by wrapping too
tightly will not be covered by the guarantee.
Helpline
If you are having a problem with your appliance,
please call our Helpline, as we are more likely to
be able to help than the store you purchased the
item from. Please have the product name, model
number and serial number to hand when you call
to help us deal with your enquiry quicker.
UK Helpline: 0344 871 0944
IRE Helpline: 1800 409 119
Spares: 0344 873 0710
Talk To Us
If you have any questions or comments, or want
some great tips to help you get the most out of
your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Contact us
Em
p
t
y
i
ng
a
nd
st
o
r
i
ng
cable
support
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 11
RN333300 MUK Rev3 06/18
Your standard 1 year guarante e is extend ed for an
a
dditional 12 months when you register the product within
2
8 days of purchase with Morphy Richards. If you do not
r
egister the product with Morphy Richards within 28 days,
y
our product is guaranteed for 1 year. To validate your 2
year guarantee register with us online at
www.morphyrichards.co.uk/support
Or call our customer registration line, quoting model and
serial number, these numbers can be found on the base of
the product.
UK 0344 871 0242
IRE 1800 409 119
N.B. Each qualifying product needs to be registered with
M
orphy Richards individually.
Please note that the 2 year guarantee is only available in
the UK and Ireland. Please refer to the 1 year guarantee
f
or more information.
It is important to retain the retailer’s receipt as proof of
purchase. Staple your receipt to this back cover for future
reference.
Please quote the following information if the product
develops a fault. These numbers can be found on the base
of the product.
Model no.
Serial no.
All Morphy Richards products are individually tested before
leaving the factory. In the unlikely event of any appliance
proving to be faulty within 28 days of purchase, it should
be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months of
original purchase, you should contact the Helpline number
quoting Model number and Serial number on the product,
or write to Morphy Richards at the address shown.
You may be asked to return a copy of proof of purchase.
Subject to the exclusions, the faulty appliance will then be
repaired or replaced as appropriate and dispatched usually
within 7 working days of receipt.
If, for any reason, this item is replaced or repaired during
the 1 year guarantee period, the guarantee on the new
item will be calculated from origin al purchase date.
Therefore it is vital to retain your original till receipt or
invoice to indicate the date of initial purchase.
To qualify for the 1 year guarantee, the appliance must
have been used according to the instructions supplied.
For example, water should be emptied after each use.
M
orphy Richards shall not be liable to replace or repair the
g
oods under the terms of the guarantee where:
1 The fault has been caused or is attributable to accidental
use, misuse, negligent use or used contrary to the
manufacturer’s recommendations or where the fault has
been caused by power surges or damage caused in transit.
2 The fault has been caused by using water other than that
recommended by Morphy Richards.
3 The fault is caused by limescale build-up.
4 T
he cables are damaged due to wrapping too tightly or
excessive kinking.
5 The appliance has been used on a voltage supply other
than that stamped on the products.
6 R
epairs have been attempted by persons other than our
s
ervice staff (or authorised dealer).
7 T
he appliance has been used for hire purposes or non
d
omestic use.
8 The appliance is second hand.
9 Morphy Richards reserves the right not to carry out any
type of servicing under the guarantee at its discretion.
• This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for
consequential loss or damage. This guarantee is offered
as an additional benefit and does not affect your statutory
rights as a consumer. Morphy Richards products are
intended for household use only. See usage limitations
within the location safety instructions.
Morphy Richards has a policy of continuous improvement
in product quality and design. The company, therefore
reserve s the right t o change th e specification of
its models at any time.
For electrical prod ucts sold within the
Europea n Commu nity. At th e end of the
electrical products useful life, it should not be
disposed of with household waste.
Please recycle where facilities exist. Check
with your Local Authority or retailer fo r
recycling advice in your country
Exclusions
Registering your 2 year
guarantee
Your 1 year guarantee
Disclaimer
The After Sales Division
Morphy Richards Ltd
Mexborough, South Yorkshire,
England, S64 8AJ
IF YOU ARE HAVING A PROBLEM
WITH ONE OF OUR PRODUCTS,
CALL OUR HELPLINE:
UK: 0344 871 0944
EIRE: 1800 409 119
SPARES: 0344 873 0710
Purolite® MB400
Causes serious eye irritation
Causes mild skin irritation.
Wash hands thoroughly after handling
Wear protective gloves / protective clothing / eye
protection / face protection.
First A id me asure s
If in eyes, rinse cautiously with water for several
minutes. Remove contact lenses if present and easy
to do, continue rinsing. If eye irritation persists, Get
medical advice / attention.
Polystyrene sulphonic acid
Polyvinyl benzyl trimethyl ammonium hydroxide
Max 30% by vol.
Fill Weight <100g
CAS 69011-20-7
CAS 69011-18-3
WARN ING
ANTI SCALE REFILL
RN333300 MUK Rev3.qxp_IB 05/06/2018 09:37 Page 12
Loading...