Morphy Richards IBMISCKETT User Manual

Page 1
TTrraaddiittiioonnaall aanndd JJuugg kkeettttlleess
This guarantee is valid in the UK and Ireland
only. It is in your interest to retain the retailers receipt as
proof of purchase. Please quote the following information if the product develops a fault. These numbers can be found on the base of the product.
Model No. Serial No.
If the fault develops after 28 days and within 24 months of original purchase, you should contact the helpline number quoting Model number and Serial number on the product, or write to the address below. You will be asked to return the product (in secure, adequate packaging) to the address below along with a copy of proof of purchase. Subject to the exclusions set out below (see ‘Exclusions’) the faulty appliance will then be repaired or replaced and dispatched usually within 7 working days of receipt.
If for any reason this item is replaced during the 2 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase.
To qualify for the 2 year guarantee the appliance must have been used according to the manufacturers instructions. For example kettles should have been regularly descaled or an iron cord should have been stored as recommended by the instructions.
EXCLUSIONS
Morphy Richards shall not be liable to replace or repair the goods under the terms of the Guarantee where: 1The fault has been caused or is attributable to
accidental use, mis-use, negligent use or used contrary
to the manufacturers recommendations or where the
fault has been caused by power surges or damage
caused in transit. 2 The appliance has been used on a voltage supply other
than that stamped on the products. 3 Repairs have been attempted by persons other than
our service staff (or authorised dealer). 4 Where the appliance has been used for hire purposes
or non-domestic use. 5 Morphy Richards are not liable to carry out any type of
servicing work, under the guarantee. 6 Plastic filters for all Morphy Richards kettles and coffee
makers are not covered by the guarantee.
This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer.
The After Sales Division, Morphy Richards Ltd, Mexborough, South Yorkshire, England, S64 8AJ Helpline (office hours): UK (local rate) 08450 777700, Republic of Ireland 1800 409119
TTwwoo yyeeaarr gguuaarraanntteeee
7271 UK kettles ib Rev 2 Mex 15/05/2003 13:39 Page 3
Page 2
2
IIMMPPOORRTTAANNTT SSAAFFEEGGUUAARRDDSS
Read all instructions
• Do not touch hot surfaces. Use handles or knobs.
• To protect against fire, electric shock and personal injury do not immerse cord, plugs or kettle in water or other liquid.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts and before cleaning the appliance.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Ring the helpline number for advice on examination and repair. NOTE: IF THE MAINS LEAD IS DAMAGED ON CORDLESS MODELS, ONLY THE BASE SHOULD BE RETURNED TO THE MANUFACTURER FOR REPAIR.
• The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury.
• Do not use outdoors.
• Do not let cord hang over edge of table counter or touch hot surfaces.
• Do not place on or near a hot gas or electric burner or in a heated oven.
• Disconnect the kettle from the mains supply when filling or pouring.
• Boil only as much water as you need as this saves electricity.
• Always close the lid securely before switching on - otherwise the kettle will not switch off automatically and it may spit out boiling water. For kettles with locking lids ensure lid is locked correctly
• WARNING: ON METAL KETTLES ENSURE THE LID KNOB IS LOCATED AT THE SIDE OF THE KETTLE, NOT THE FRONT OR REAR, SO THAT STEAM IS DIRECTED AWAY FROM THE HANDLE.
• WARNING: DO NOT REMOVE THE LID WHILE THE WATER IS BOILING.
• Always take care to pour boiling water slowly and carefully without tipping the kettle too fast.
• Always put in enough water to cover the element; on models with a water level gauge, this is indicated by the MIN mark.
• Ensure that the kettle is used on a firm, flat surface.
• Avoid contact with steam from the spout when the water is boiling or just after it has switched off. Take care if opening the lid for re-filling when the kettle is hot.
• Do not fill above the MAX mark on the water level gauge or inside of the kettle body.
WARNING: DO NOT IMMERSE THE KETTLE OR BASE UNIT IN WATER. WARNING: IF THIS KETTLE IS OVERFILLED BOILING WATER MAY BE EJECTED. WARNING: DO NOT TIP KETTLE BACKWARDS AS BOILING WATER MAY BE EJECTED.
• Do not hold the switch in the ON position or tamper with the switch to fix it in the ON position as this may cause steam to be ejected from around the lid and could damage the automatic switch-off mechanism.
• Do not attempt to connect any other appliance to the cordless base unit, or tamper with the connector in any way (special interlocked shutters are designed to prevent access to the live pins until the kettle is attached to the base unit).
• Do not use abrasive cleaners on the outside of the kettle - these may scratch the surface.
• Do not use the kettle for any use other than to boil water.
• Extreme caution must be used when moving an appliance containing hot water.
• Always attach plug to appliance first, then plug into the wall outlet. To disconnect, turn any control to off, then remove plug from wall socket.
Warning: Do not place the base unit onto a metal tray or metal surface whilst in use.
SAVE THESE INSTRUCTIONS
7271 UK kettles ib Rev 2 Mex 15/05/2003 13:39 Page 4
Page 3
EElleeccttrriiccaall rreeqquuiirreemmeennttss
Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating Current).
If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed and the appropriate one fitted.
Note: The plug removed from the mains lead, if severed, must be destroyed as a plug with bared flexible cord is hazardous if engaged into a live socket outlet.
WARNING: THIS APPLIANCE MUST BE EARTHED.
Should the fuse in the 13 amp plug require replacement, a BS1362 13 amp fuse must be fitted.
AAddvviiccee oonn ssccaallee
If you live in a hard water area, scale will form on the inside of your kettle during boiling. This can pour into your drink spoiling its appearance and taste. If your kettle is fitted with a limescale filter, it will retain unsightly pieces of scale within the kettle and prevent them getting into your drink.
A limescale filter will not, however, prevent scale from forming inside the kettle. Therefore, it is important that the filter and inside of the kettle be cleaned regularly, especially if you live in a hard water area. Failure to do so will reduce the kettle’s filling and pouring capability and will invalidate the guarantee. See sections on Cleaning and Descaling.
IN HARD WATER AREAS ALWAYS FILL THE KETTLE THROUGH THE SPOUT AS THIS HELPS TO FREE THE FILTER FROM LIMESCALE BUILD-UP.
IF FILLING AND POURING THROUGH THE SPOUT BECOMES SLOW, THIS IS AN INDICATION THAT THE FILTER IS READY FOR CLEANING OR DESCALING.
NOTE: Scale is a natural substance formed during the boiling of water in hard water areas and is not harmful to health. SHOULD YOU REQUIRE SERVICE, ADVICE OR REPAIRS TO YOUR APPLIANCE, PLEASE USE THE HELPLINE TELEPHONE NUMBERS ON THE FRONT OF THIS LEAFLET.
IInnssttrruuccttiioonn ffoorr uussee
CCoorrddeedd mmooddeellss
FIll the kettle with at least enough water to reach the
MIN mark. Don’t overfill it - see Important Safeguards.
Push the mains lead connector FIRMLY into the
kettle, plug in and switch on at the wall socket.
Switch the kettle on. The red neon will light up to indicate the water is starting to boil (certain models only).
When the water boils, the kettle will switch off automatically. As it does so, a drop of water may emerge from the vent in the bottom of the kettle handle. This is normal and not a fault.
If you are using the kettle for the first time, pour away the boiled water and refill.
To re-boil, switch to ON again. If the kettle has just switched off, wait a minute or so before switching it back on again.
If you do not put in enough water, or switch on the kettle when it is empty, the safety cut-out will switch off the power automatically. If this happens, wait a few minutes for the element to cool, then refill and use as normal.
CCoorrddlleessss mmooddeellss
See previous section on corded model for general instructions. The following instructions refer to models with a cordless base.
After filling with water, take the kettle to the base unit, hold the kettle level, then gently, but firmly, push the rear of the kettle to engage the base unit connector. Plug in and switch on at the wall socket.
IMPORTANT: Ensure that the kettle has switched off automatically, or is switched off manually, before removing it from the base unit.
To remove the kettle from the base unit, switch off at the wall socket, grasp the handle and hold the kettle level while lifting it clear of the base unit. Take extra care if the kettle is filled to MAX.
If you are using the kettle for the first time, pour away the boiled water and refill.
WARNING: THE KETTLE MUST ONLY BE USED WITH THE BASE UNIT PROVIDED AND SHOULD NOT BE ON THE BASE UNIT WHEN BEING FILLED WITH WATER.
WARNING: THE JUG KETTLE CORDLESS BASE UNIT IS A SEALED UNIT: IF THE MAINS LEAD OR OTHER PART BECOME DAMAGED, THE CORDLESS BASE SHOULD BE DISCARDED AND REPLACED.
3
7271 UK kettles ib Rev 2 Mex 15/05/2003 13:39 Page 5
Page 4
4
MMiinnii jjuugg mmooddeellss
The mini jug can be used on voltages between 110V and 240V AC only. Ensure the correct plug adaptor is used when operating in a country not using the UK 13 amp socket system. If in doubt consult a competent electrician.
Note: If using the jug on a 110 volt supply, the water will take considerably longer to boil.
MMooddeellss wwiitthh ddeessccaallee nneeoonn
These models are fitted with 2 indicator neons for your benefit.
Red neon: This indicates when the element is energised. When the water boils and the element switches off, the neon will go out.
Orange neon: This indicates that either the kettle is in need of descaling or that the kettle has been switched on without water in.
If the orange neon comes on due to scale build-up on the element (this will happen frequently if you live in a hard water area) follow the descaling instructions in this leaflet.
If the orange neon comes on due to lack of water in the kettle, wait a few minutes for the kettle to cool, refill with cold water and use as normal.
GGeenneerraall cclleeaanniinngg
In order to maintain the pouring and boiling performance of your kettle, it is important to clean and wash out the interior of the kettle regularly, particularly in hard water areas. This also applies to the filter, if fitted. Please also refer to section on Descaling.
To flush scale deposits from the interior of the kettle, fill with cold water through the spout and empty out through the spout with filter removed. The interior may also be wiped carefully using a soft clean damp cloth.
Wipe the outside of the kettle with a soft damp cloth only, avoiding electrical connections.
FFiilltteerr rreemmoovvaall aanndd cclleeaanniinngg
((cceerrttaaiinn mmooddeellss oonnllyy))
WARNING: ALLOW KETTLE TO COOL COMPLETELY BEFORE REMOVING FILTER.
FFiilltteerr JJuugg KKeettttlleess
To remove the filter, open the lid and lift the filter vertically from its location using the tab provided.
To refit the filter, position between the 2 side wall guides and press down firmly. Ensure the filter is correctly located into the central guide.
NOTE: UNLESS THE FILTER IS FITTED CORRECTLY, THE KETTLE LID MAY NOT CLOSE AND LOCK SECURELY.
FFiilltteerrmmaasstteerr TTrraaddiittiioonnaall KKeettttllee
To remove filter, pull top of filter forwards from under handle front and lift.
Refit the filter by pushing down firmly into spout until the filter latches into position under handle front.
CClleeaanniinngg tthhee ffiilltteerr
Once removed from the kettle, clean the filter by brushing gently with a small soft brush under water. Any hard deposits of scale may be removed by de-scaling. Do not use a sharp object which may damage the filter mesh.
Red ‘on’ neon
Orange ‘descale’ neon
RReemmoovviinngg ffiilltteerr
7271 UK kettles ib Rev 2 Mex 15/05/2003 13:39 Page 6
Page 5
5
DDeessccaalliinngg
IF YOU LIVE IN A HARD WATER AREA, SCALE WILL FORM ON THE INSIDE OF YOUR KETTLE AND ITS ELEMENT. THIS COULD CAUSE THE KETTLE TO MALFUNCTION AND MAY DAMAGE THE ELEMENT INVALIDATING THE WARRANTY. IT IS ESSENTIAL THAT REGULAR DESCALING TAKES PLACE AS FOLLOWS:
Soft scale may be removed by brushing the cool element regularly. Remove hard scale using either a proprietary descaling product suitable for plastic kettles (following the instructions carefully), or citric acid crystals. We recommend using citric acid crystals as follows:
Boil 1 litre of water, then unplug the kettle (remove the cordless kettle from the base unit) and stand it in an empty sink or bowl. Add 50gm of citric acid crystals to the water gradually, then leave the kettle to stand. DO NOT USE A MORE CONCENTRATED SOLUTION. If the filter requires descaling this may be achieved by dropping it into the citric acid solution within the kettle (certain models only).
As soon as the effervescence subsides, empty the kettle and rinse it thoroughly with cold water.
Wipe the outside of the kettle thoroughly with a damp cloth to remove all traces of acid which may damage the finish.
Ensure that the electrical connections are completely dry before using the kettle.
Citric acid crystals are available from most pharmacies.
Failure to descale will invalidate the guarantee.
SSaaffeettyy iinn tthhee kkiittcchheenn
Morphy Richards is concerned that accidents involving kettles or their mains lead can cause death or serious injury through scalding. We therefore offer the following advice in the hope that it will prevent such accidents occurring.
BBooiilliinngg wwaatteerr
•Boiling water is used so often in the home: tea
and coffee making, cleaning, cooking, warming-
up. This means that your kettle is a potential
mobile accident area.
•Always locate your kettle away from the edge
of a worktop. Do not let the mains lead hang
over the edge of a worktop where a child
could reach it.
• Do not let the lead run across an open space
e.g. between a low socket and table.
• Do not let the lead run across a cooker or
toaster or other hot area which might damage
the cable.
• Do not place the kettle where the mains lead
connector could fall into the kitchen sink.
CChhiillddrreenn
Your own and other children are vulnerable in the kitchen particularly when unsupervised and if appliances are being used or cooking is being carried out. Teach children to be aware of dangers in the the kitchen, warn them of the dangers of reaching up to areas where they cannot see properly or should not be reaching.
OOtthheerr aapppplliiaanncceess
Remember other products can cause serious injury in the kitchen.
• Deep fat fryers or frying pans contain hot oil
at a temperature far higher than boiling water.
• Irons are very hot and can cause serious
injury if knocked by a child from an
unattended ironing board.
• Irons have long mains cables which can fray -
look after your cable.
• Saucepans where possible should be placed on
back cooker rings: turn the saucepan handle
away from the edge of your cooker.
AAcccciiddeennttss
If a scald occurs run cold water over the affected area immediately. Do not stop to remove clothing, get medical help quickly.
7271 UK kettles ib Rev 2 Mex 15/05/2003 13:39 Page 1
Page 6
Morphy Richards Limited, Mexborough, South Yorkshire, England S64 8AJ
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and design.
The Company, therefore, reserves the right to change the specification of its models at any time.
Filtermaster jug kettles 4323X
Filter Plus jug kettles 4344X/4345X
Jug kettles 4302X/4303X
Jug kettles 4325X/4305X/4304X
Jug kettles 4301X
Marlin jug kettles 4378X/4379X
Mini Jug kettles 4327X
Filtermaster traditional kettles 4332X/4333X
Plastic traditional kettles 4335X
Traditional stainless steel kettles 4338X/4339X
Stainless steel maxi kettles 43395
Product Series model number
08/16160/0 Rev 3
440-8053-01 Rev 3
June 2000
7271 UK kettles ib Rev 2 Mex 15/05/2003 13:39 Page 2
Loading...