INSTRUCTIONS
This guarantee is valid in the UK and Ireland only. It
is in your interest to retain the retailers receipt as
proof of purchase. Please quote the following information
if the product develops a fault.These numbers can be
found on the base of the product.
Model No. Serial No.
All Morphy Richards products are individually tested
before leaving the factory.In the unlikely event of any
appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase
for it to be replaced.
If the fault develops after 28 days and within 24
months of original purchase, you should take the
appliance to your nearest service agent.A list containing
details of your nearest service agent is included with
your appliance but please contact the helpline quoting
Model number and Serial number should you require
further assistance, Repair or replacement of the
product is subject to the following exclusions (see
Exclusions).
If you suspect a fault, follow the simple checks
detailed below before returning the appliance or calling
the helpline:
1 -Check the plug is firmly in the socket and the
supply is switched on.
2 -Make sure the socket is working by trying
another appliance.
To qualify for the 2 year parts and labour guarantee
the appliance must have been used according to the
manufacturers instructions.
EXCLUSIONS
Morphy Richards shall not be liable to replace or
repair the goods under the terms of the Guarantee
where:
1 -The fault has been caused or is attributable to
accidental use, mis-use, negligent use or used
contrary to the manufacturers recommendations or
where the fault has been caused by power surges or
damage caused in transit.
2 -The appliance has been used on a voltage supply
other than that stamped on the products.
3 -Repairs have been attempted by persons other
than our service staff (or authorised dealer).
4 -Where the appliance has been used for hire
purposes or non-domestic use.
5 -The guarantee excludes consumables.
This guarantee does not confer any rights other
than those expressly set out above and does not cover
any claims for consequential loss or damage.This
guarantee is offered as an additional benefit and does
not affect your statutory rights as a consumer.
If for any reason this item is replaced during the 2
year guarantee period, the guarantee on the new item
will be calculated from original purchase date.Therefore
it is vital to retain your original till receipt or invoice to
indicate the date of initial purchase.
The After Sales Division,Morphy Richards Ltd, Mexborough,South Yorkshire,England, S64 8AJ
Helpline (office hours): UK (local rate) 0870 0602606
2 YEAR PARTS AND LABOUR GUARANTEE
Features
Filler cap
Heater On/off button
Steam On/off button
Machine socket
‘Heater on’ indicator light
‘Steam ready’ indicator light
‘Refill’ indicator light
‘Steam’ indicator light
Carrying handle
Flexible Hose
Hose plug
Handle with remote steam control
Handle control steam switch
Locking mechanism (safety lock)
Extension tube
Release button
Variable steam knob (optional)
Standard Accessories
Cotton towel
Funnel
Large floor brush
Brush connector
Jet nozzle
Round bristle brush (metallic)
Round bristle brush (nylon)
Hand held squeegee with
big and small blades
Luxury Optional Accessories
Integrated Window cleaner
Triangular brush
Wall paper stripper
Professional Iron
Iron Pad
Important Safeguards
This product has been designed with your
safety in mind. However, for safe operation, it is
important that you observe the following points:
•To obtain best results from your steam
cleaner, please read these instructions
carefully and keep them in a safe place.
• This product conforms to the relevant
safety regulations for electrical appliances
• Use only genuine Morphy Richards spare
parts and accessories
• If the electrical cable becomes damaged, the
complete cable assembly must be replaced.
Do not attempt this task yourself, contact
your local Authorised Service Agent
• Do not discharge steam towards people.
Danger of scalding!
• Never allow children to play with
or use this appliance
• Always unplug the machine when:-
- the machine is not in use
- cleaning the machine
- filling the boiler with water
• When using the machine always keep
it horizontal
• Do not use the machine for other purposes
than it was built for
• Steam must not be directed towards
equipment containing electrical components,
such as the interior of ovens.
• Do not use any chemical detergents,
perfumes, alcohol etc in the water
• When exchanging the accessory heads
during use, please note these are hot.
• Never touch the plug or power cable with
wet hands
• Repairs to electrical appliances are only to
be undertaken by authorised service
agents. Unprofessional repairs can be
dangerous for users
Please remember that the steam cleaner
operates by emitting steam at an increased
temperature of up to 1400C. Never use it on
objects or surfaces which cannot resist this
temperature (delicate materials, Dralon,
plastic, natural fur etc). Where any doubt exists
check carefully on a part of the material where
minor marks will not matter!!!!
Electrical connection and supply
THIS APPLIANCE MUST ONLY BE USED ON
AN EARTHED SUPPLY
Check that the supply voltage details given on
the rating plate (located on the underside of the
product) are in accordance with your electricity
supply.
For Appliances with fitted plug. If the socket outlets in your home are not suitable for the plug
supplied with this appliance the plug should be
removed and the appropriate one fitted.
Please note: The plug severed from the mains
lead must be destroyed as a plug with bared
flexible cord attached is hazardous if engaged
in a live socket outlet. Should the fuse in the
13 amp plug require changing a 13 amp
BS1362 fuse must be fitted.
European conformity information
This product conforms to the following
European Directives: low voltage 73/23/EEC,
EMC 89/336/EEC and CE Marking
93/68/EEC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
18
19
20
21
22
23
25
26
24
28
29
15
30
1
2 3
27
2. Twist connector 1800, until it is in place.
(Fig F)
The fit between the connector and the
tubes and/or handle is tight to ensure no
steam leaks. It is recommended to keep
both parts lubricated to facilitate connecting
and disconnecting.
To detach the accessories, press the
release button (16) and pull the items apart.
Please note accessory heads may be hot!
Please be careful not to trap your fingers.
OPERATING YOUR STEAM CLEANER
Connect the unit to the mains and switch
on the boiler heater by pressing the on-off
button (2). The ‘heater on’ light is illuminated.
Steam will be available in approx. 10 minutes.
When the steam is ready for use the
‘steam ready’ light (6) will turn green.
Make sure that the locking mechanism
(14) on the handle has been released.
If you push the lock (14) towards the rear,
the steam switch can not be operated.
Push the lock forward so that the steam
switch is released. (Fig G)
To make steam ready press the ‘steam
on/off’ button (3) and the orange light (8)
will come on. STEAM IS NOW READY TO
BE RELEASED.
To release steam, press the handle
control switch (13). At the start, always
point the steam handle at a cloth until a
steady flow of steam comes out.
During steam release the green light will
turn off.
To stop releasing steam, simply release
the handle control switch (13).
If your steamer features a varisteam knob
(17) the steam flow can be adjusted to
specific requirements.
Turn the varisteam knob fully anticlockwise
for maximum steam and clockwise for
minimum steam flow. (Fig H)
If the ‘refill’ indicator light (7) turns red,
the boiler must be refilled.
SETTING UP YOUR STEAM CLEANER
Filling the boiler
Unscrew the filler cap (1) anti clockwise
Fill the boiler with a maximum of 1.8
litres of water by using the funnel (19)
provided (Fig A)
Do not use any detergents.
Screw the filler cap (1) clockwise until
finger tight. Do not over tighten.
Attaching Hose and Accessories
Pull down flap on the front of the
machine socket.
Insert the plug on the end of the hose (11)
into the machine socket (4) with button
side facing up, and push firmly until it
clicks into place. (Fig B)
Attach the desired accessory, i.e. large
floor brush (20), triangular nozzle (27), jet
nozzle (22), window cleaner (26), to the
extension tube (15) or directly to the
handle (12), depending on the application.
The accessories vary per machine
The round brush(es) (23 & 24) can be
attached to the jet nozzle.
To join the extension tubes together, slide
one tube into the other until it locks into
place. (Fig C)
Attach the two tubes to the handle of
the hose. Slide the handle into the
extension tube until it locks into place.
(Fig D).
Some tasks may be easier with only one tube
fitted or none at all.
To connect the desired accessory directly
to the steam handle, slide the handle into
the accessory head until it locks into place.
When using the large floor brush (20) or
the triangular brush (27), the brush
connector (21) needs to be fitted to the
brush first, in order to attach the same to
the extension tube.
To fit the connector:
1. Push the connector end, holding it upside
down, fully into the brush inlet. (Fig E)
A
C
D
E
F
G
H
B
12
13
14
17
4 5
The jet nozzle can be attached either directly
to the handle or via the extension tubes.
The closer you hold the jet nozzle to the
object to be cleaned, the better the
cleaning results will be.
The round bristle brushes can be snapped
onto the end of the jet nozzle.
The nylon brush is suitable for most
cleaning applications such as: grout, tap
ware, toilets, bathrooms, fridge seals and
sliding door runners.
The metallic brush is suitable for more
stubborn dirt where a more abrasive
action will not affect the surface, such as
BBQ plates and lime scale in toilets.
Hand held squeegee with big and small blades (25)
This squeegee cannot be attached to the
extension tubes and/or steam handle
Use the jet nozzle (22) to apply steam to
the window at a distance of at least 30cm.
Squeegee the window in straight passes from
top to bottom. Wipe the blade and the bottom
edge of the window dry after each pass.
Blades on the hand-held window cleaner
can be interchanged, according to the
width of surface being cleaned.
Triangular brush (27) *
Recommended applications include
- smaller washable areas, such as:
- kitchen and bathroom surfaces
- car interiors
- upholstery
The triangular brush can be attached to
the extension tubes or directly to the
steam handle, provided that the brush
connector (21) is fitted.
Integrated Window cleaner (26) *
Fit the window cleaner to the handle
(attach extension tubes if required).
To ‘steam clean’ the surface, place the
thick rubber of the accessory head against
the glass, whilst releasing steam (13).
Keep the steam control switch (13)
pressed until the entire surface is covered
with steam.
To remove excess water turn the accessory
head around with the squeegee against
the surface. Move the squeegee in straight
passes from top to bottom. Wipe the
rubber blade and the bottom edge of the
widow dry after each pass.
Professional Iron (29) *
The high steam professional iron produces
up to 6 times more steam than a normal
domestic iron, and is up to 4 times faster.
Note: Do not stand the iron on its end,
always place it with the sole plate down on
the iron pad (30) supplied.
Firmly insert the plug of the iron into the
machine socket of the cleaner until it
locks in place.
The temperature setting on the iron needs
to be set to the correct setting for the
fabric concerned.
Press the steam on/off button (3) on the
machine. Both orange lights will come on.
The light on the iron will turn off when it
has reached the desired temperature.
When the steam is ready for use and the
iron is hot, place your thumb on the large
switch located at the top of the iron, to
release steam.
Release some steam away from the fabric
before commencing ironing until a steady
flow of steam comes out.
The iron can be used vertically to ‘steam-
iron’ curtains, dresses, etc.
Wallpaper stripper (28) *
Fit wallpaper stripper directly to the hose
handle. locking into place. Some tasks
may be easier with extension tubes fitted.
Press the steam release button (3) The
orange light will turn on.
Place the wallpaper stripper with its entire
surface on the edge of a sheet of wallpaper.
Allow the steam to penetrate until the
wallpaper is soaked through (approx.10 sec.)
Refilling
When the ‘refill’ light (7) turns red there
should be no steam available for release.
The boiler needs to be refilled:
Switch off the boiler heater by pressing
the on/off button (2)
If there is pressure in the boiler, the filler
cap (1) will revolve but a safety feature
prevents it from being unscrewed.
Release any steam pressure in the system
using the on/off switch (3) on machine
and handle (13). Switch off the steam
release button (3). The cap can then be
unscrewed.
Unplug the mains cable.
Leave the product with the filler cap off
for 10 minutes before filling.
Refill the boiler using the funnel (Fig A).
Use warm water to reduce heat up time
Caution: Do not pour cold water into a very
hot boiler as steam and hot water may be
blown out of the filling hole and can scald!!!
Screw the cap back on. Start operation
again (SEE OPERATION SECTION ABOVE)
Switching the unit OFF
Switch the unit off by means of switches
(2) and (3).
Remove the hose plug (11) from the unit
by pressing the button, holding down the
socket flap simultaneously.
Remove the plug from the mains socket.
Any remaining water can be left inside
the unit.
To avoid deforming the brushes (23 & 24),
ensure that the brushes are allowed to
cool down before storing.
USE OF ACCESSORIES
Steam handle (12)
To avoid spurting of heavy and moist steam it
is recommended always to attach an accessory
to the steam handle.
Large floor brush (20)
Recommended applications include:
- carpets and rugs
- sealed timber & parquetry
- ceramic tiles
- vinyl
The large floor brush can be attached to
the extension tubes or directly to the
steam handle, provided that the brush
connector (21) is fitted.
Stretch the cotton cloth lightly over the
bristles using the clips provided on the
brush head. (Fig I)
Switch on the steam and move the
cloth-covered brush gently over the surfaces to be cleaned.
Replace cloth regularly so that more dirt
can be collected and to avoid too much
moisture being applied to the floor and
leaving it very wet.
Heavily soiled areas will require more
attention to allow steam more time to act
on the dirt while lightly soiled and smooth
surfaces will only require a quick wipe.
Jet nozzle (22) and round brush (23 & 24)
Recommended applications with round
brush include:
- Hard to reach surfaces such as corners
and joints
- Toilets and sanitary installations
- Venetian blinds
Without round brush
- Defrosting freezers
- Eliminating odours and creases in clothing.
Firstly place the garment on to a clothes
hanger and spray steam at a distance of
around 10 – 20 cm.
- Removing dust from plants.
Maintain a distance of around 30 – 40 cm
to avoid burning leaves by direct contact
with steam.
I
6 7
J
Without switching it off, move the wallpaper
stripper to a new location.
Use a putty knife to lift the loosened wall
paper, and pull it off completely.
* These accessories are available as optional
extras, if not supplied with your machine.
Please contact your helpline for more
information
MAINTENANCE & TROUBLESHOOTING
Cleaning the boiler
Disconnect from mains and make sure it
is cold.
To clean the boiler, fill the boiler with water
and shake it vigorously to loosen any scale
that has settled at the bottom of the boiler.
Pour the water out of the boiler and the
scale will be flushed out.
De-scaling the boiler
In order to keep the heat-up time constant it is
recommended to de-scale your cleaner at
regular intervals.
Mix one litre of water with 0.25 litre of
vinegar and pour into the boiler with the
funnel provided.
Shake the cleaner and then allow the
mixture to work for at least one hour.
Rinse the boiler until water is clear
Trouble shooting guide
CONSUMABLES
If you experience any difficulty in obtaining
service or spare parts, please telephone our
Customer Helpline (during office hours):
UK Helpline 0870 0602606
Replacement Parts 0870 1676637
IRELAND 1800 409119
The After Sales division Morphy richards
Mexborough
South Yorkshire
S64 8AJ
FAULT POSSIBLE CAUSE SOLUTION
No steam No electrical supply Check fuse, cable plug and socket
Unit not switched on Switch on correct switch and read instructions
Switch to power remote
handle control not switched on As above
Hose connector not pushed Make sure hose connector is assembled
in properly correctly to cleaner
No water in boiler Refill with water as instructions
Very little steam Variable steam controller not open Adjust steam controller knob
Some models only
Very long heat up time Unit calcified De calcify (de-scale) unit
Loud whistling noise Pressure fault Return the product to your
accompanied by steam authorised customer service agent.
from rear of machine
If you encounter any other problems with the product, contact your local authorised customer
service agent.
P/N S8792770 03/03
Loading...