Morphy richards HA4009 user Manual
Important Safeguards
Two Year Guarantee
When using your hair appliance, basic safety
precautions should always be followed.
1 Read all instructions carefully.
2 Use the appliance for its intended use only.
3 To protect against the risk of electric shock,
do not immerse the appliance in water or in
any other liquids.
4 Be sure that your household voltage
corresponds to the voltage marked on the
dryer.
5 The air inlet grille should not be obstructed
when the styler is in use.
6 Always unplug your appliance when it is not
in use.
7 It is recommended that this appliance should
not be used by children.
8 Do not leave the styler switched on
whilst unattended.
9 This appliance is equipped with a swivel cord
which must if damaged, be replaced by a swivel
cord of the same type. The cord must be replaced
by Morphy Richards as special tools are required.
Wiring
This product is fitted with a 13A (BS1363) plug.
A 3 amp fuse (BS1362) must be used.
Check that the voltage on the rating plate of your
appliance corresponds with your house electricity
supply which must be A.C. (Alternating Current).
If the socket outlets in your home are not suitable for
the plug supplied with this appliance the plug should be
removed and the appropriate one fitted.
IMPORTANT : THE PLUG REMOVED FROM THE MAINS
LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG
WITH BARED FLEXIBLE CORD IS HAZARDOUS IF
ENGAGED INTO A LIVE SOCKET OUTLET.
It is in your interest to retain the retailers receipt
as proof of purchase. Please quote the model
number if the product develops a fault. This number
can be found on the handle of the product.
All Morphy Richards products are individually tested
before leaving the factory. In the unlikely event of
any appliance proving to be faulty within 28 days
of purchase it should be returned to the place of
purchase for it to be replaced.
If a fault develops after 28 days and within 24
months of original purchase, you should contact
the helpline number quoting the model number of
the product, or write to the address below. You
will be asked to return the product (in secure packaging) to the address below along with a copy of
proof of purchase.
The After Sales Division
Morphy Richards Ltd
Mexborough
South Yorkshire
England
S64 8AJ
Helpline (8:30-5:00 Mon-Thur/ 8:30-4:00 Fri)
UK (local rate) 08450 777700,
Republic of Ireland 1800 409119
Morphy Richards products are intended for household
use only. Morphy Richards has a policy of continuous
improvement in product quality and design. The
Company, therefore, reserves the right to change the
specification of its models at any time.
CP 4009 Issue 1
04.00
Imported by : Morphy Richards Ltd, Talbot Road, Mexborough, S64 8AJ
300w Hot air styler
with multi-attachments
MODEL : HA4009
Instructions & Style Guide
Thank you for buying your new 300w Essentials Hot Air
Styler from Morphy Richards. Please read these
instructions carefully before use and keep in a safe
place for future reference.
Key Features
D
tong
bristle
brush
A 300 watts.
B 4 styling attachments.
· shaper brush.
· bristle brush.
· volumiser.
· Tong.
C Curl release button for easy use.
D Control switch on main barrel for easy operation.
(2 speed/heat settings)
E Tangel free swivel cord for easy use.
F Stylish metallic finish.
G Hanging loop for easy storage.
H 2 metre salon length cable.
volumiser
C
shaper
brush
B
Styling
The vent bristle brush - can be used to shape, it is
suited to general styling and creating a textured look.
Rough dry your hair, using a Morphy Richards hairdryer,
before using your Hot Air Styler.
Set your Hot Air Styler on the highest setting. Lift a
small section of hair onto the vent bristle brush and
brush downwards, maintaining tension. Repeat on all
sections of hair until the desired result is achieved.
Using the Volumising attachment Set the Hot Air
Styler on the highest setting when the hair is at its
most wet. Place fingers of the styler to the head
allowing the roots to dry first which creates maximum
volume.
As the hair dries, lower the settings and lift the styler,
working up through the hair to create height.
Using the tong attachment - Blow dry the hair,
using a Morphy Richards hairdryer, by brushing the hair
from the roots to the ends in the direction of normal
growth, to add body. Brush into the desired shape.
Now take a section of hair. Raise the tong by pressing
the long lift button. Place the outer end of the section
of hair between the tong and barrel and lower the tong
to trap the end of the section of hair.
Rotate the handle to wind the hair outside of the tong.
Leave the tong in place for 10-15 seconds (depending
on length and thickness of hair) then unwind carefully.
Raise the tong to release the hair and leave curl in
position until it has cooled. Repeat all around head.
Using the Shaper Brush attachment - Rough dry
the hair using a Morphy Richards hairdryer. Brush into
the desired shape.
Divide the hair into sections, small sections for tighter
curls, large sections for body and curl.
To release the hair press the curl release button and
unwind the hair carefully.
Stroke the brush from the roots to the ends of each
section of hair and then rotate the handle to wind the
hair round the brush, winding inwards towards the
scalp. Leave for 20-30 seconds (depending upon the
length and thickness of hair) then unwind carefully.
Repeat all around head.
Styling Tips
Your Hot Air Styler is one of the most important beauty
aids you own, and the way you use it has a significant
impact on the look and condition of your hair.
Having shampooed your hair, ensure that it is rinsed
properly as shampoo that is left in the hair will leave it
looking dull.
To maximise shine, rinse your hair in cool water when
you have rinsed it thoroughly.
Comb your hair through with a wide toothed comb to
remove tangles before styling.
To change the attachments
Your Essentials Hot Air Styler has 4 styling attachments.
To remove an attachment pull the attachment away
from the handle. To fit a new attachment, line up the
locating slots on the attachment with the slots on the
end of the handle and push to lock in place.
Always unplug the unit before removing or fitting new
attachments.
Mains Lead
As a safety precaution and to prolong the life of your
appliance, do not wrap the mains lead around the
appliance as this will cause damage.
Loading...