Mooer R7 X2 STEREO User manual

R7 X2 STEREO

REVERB PEDAL

Precautions

PLEASE READ CAREFULLY BEFORE PROCEEDING

Power Supply

Please connect the designated AC adapter to an AC outlet of the correct

voltage. Be sure to only use an AC adapter which supplies 9V DC, 300mA.

Unplug the AC power adapter when not in use or during electrical storms.

Location

To avoid deformation, discoloration, or other serious damage, do not

expose this unit to the following conditions:

• Direct sunlight or other heat sources • Magnetic fields

• Excessively dusty or dirty locations • Strong vibrations or shocks

• High humidity or moisture

Radio Frequency Interference

Radios and televisions placed nearby may experience reception

interference. Operate this unit at a suitable distance from radios and

televisions.

Cleaning

Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth.

Do not use abrasive cleanser, cleaning alcohol, paint thinners, wax,

solvents, cleaning fluids, or chemical-impregnated wiping cloths.

Feature

● 14 different types of high-quality stereo reverb.

● Storablepresetforeacheffect can be recalled quickly.

● "INFINITE"function for endless reverb tail, a perfect choice for creating

atmosphere.

● Tap footswitch to change preset.

● Trail On function allows effects to fade out naturally. You can toggle between

ON and OFF seamlessly.

Layout

17

01

11	02
03	04
05	06
07	08
09	10

14

15	12
16	13

1.HC

Control high frequency cut of reverb. 2.2kHz for O . Frequency Range (Hz)

20kHz~2.2kHz

2.MIX

Control the mix rate of dry signal and reverb. Minimum level : 100% dry signal ,

0% reverb . Median level: 50% dry signal , 50% reverb. Maximum level(kill dry):

0%dry signal , 100% reverb.

3.LC

Control low frequency cut of reverb. 20Hz for O .Frequency Range (Hz)

20Hz~520Hz

4.DECAY

Adjusts the length of the reverb decay.

5.SAVE

Press to cycle through preset slots. Press and hold SAVE to save current audio file.

6.PRE-DLY

Control reverbpre-delay ( at the preset slot of Spring reverb the parameter

simulates the length of the spring)

7.Left footswitch LED

Indicates the on/off of the INFINITE effect. When it is on, the indicator will flash.

8.Right footswitch LED

Indicates the on/off, trail on/off of the pedal, Blue: On; Red: OFF

9.Left footswitch

In normal mode, press and hold the footswitch to activate INFINITE mode. Roll

up slots in preset select mode.

10.Right footswitch

Press to switch on/off. Roll down slots in preset select mode.

11.LED indicator

Indicates current preset bank, preset patch, changing/storing of presets.

Yellow: Preset 1~7; Purple: Preset8~14

12.INPUT (MONO) L

1/4'' mono audio input.

13.INPUT R

1/4'' mono audio input.

14.Effect list

Shows the 14 different effects name.

15.OUTPUT (MONO) L

1/4"mono audio output.

16. OUTPUT R

1/4'' mono audio input

17. DC IN

9V/300mA power supply (Center negative). Original power supply is

recommended to avoid unexpected noise.

18.Effect list

Connections

MONO setup

Guitar amplifier

Guitar

pedalboard

Left output

Left input

MONO setup on the FX LOOP of amplifier

Left output

Left input

RETURN

SEND

Guitar

Guitar amplifier

Stereo setup
Amplifier (Left)
		Guitar
Left output	Left input	pedalboard
Right output	Right input
Amplifier (Right)
FactoryReset
Stereo Setup with FX LOOP of amplifier
RETURN
		SEND
		INPUT
		RETURN
INPUT
SEND
	Guitar

Instructions

1. Select effect

(1) Normal mode. Turn on the pedal and press the SAVE button to switch between each effect.

(2) Preset rolling mode. Turn the pedal on and press TAP and BYPASS simultaneously to enter preset switching mode which will be indicated by the footswitch LED and SAVE button blinking in red. In this mode, users can roll down/up through each effect by using the TAP and BYPASS footswitches. The pedal will exit rolling mode if the pedal is idle for 3 seconds.

2. Preset saving

The LED indicator will blink slowly when any parameter has been changed. Users can press and hold the SAVE button to store changes. The LED indicator will blink quickly for a short duration to confirm saving. Alternatively, users can quickly press the SAVE button again to cancel those changes.

3. TAP TEMPO

Turn on the pedal and press the TAP footswitch several times to set up a tap tempo speed. The TAP LED indicator will show current speed by blinking.

4. Trail On/Off

After turning on the pedal, press and hold the BYPASS footswitch for 2 seconds. The BYPASS indicator will blink and change color to confirm. The blue LED indicates trail mode is on while Red indicates trail mode is off.

5. Factory reset

Unplug the power cord then press and hold the SAVE button while powering on the pedal again. The 7 LEDs will start to blink slowly. Release the SAVE button and the LED indicator will blink quickly to confirm a successful factory reset. You can unplug the power cord before releasing the SAVE button to cancel the factory reset.

* Factory reset will clear all presets stored by user.

			Effect List
Slot	LED	Reverb	Description
	Color	Name
1		Room	Warm, slow, and short reverberation of a room.
2		Hall	Long and spacious reverberation of a hall.
3			Solemn and splendid reverberation of a church. This
		Church	reverb simulates the reverberation of a empty room
			with dense surface.
4	Yellow	Cave	Dark and deep cave reverberation of a cave with
			long pre-delay. This reverb simulates the
			reverberation of a rock cave with irregul ar surface.
5		Plate	Classic clear metallic-sounding reverberation.
6		Spring	This simulates spring reverb of a old-style guitar
			amp .
7		Mod	Dynamic atmosphere modulated reverberation.
1		Studio	Reverberation of a small and medium-sized studio
			with balanced frequency response.
2		Reverse	Supernatural reverse reverberation. This reverb
			simulates reflection and inverted diffusion.
3		Warp	Pleasing and silvery modulated reverberation.
4	Purple	Shake	Modulated reverberation. This reverb simulates
			air vibration.
5		Crush	Downsampling reverberation. This reverb
			simulates the way of stars shining.
6		Shimmer	Broad and gorgeous octave reverberation.
7		Dream	The gentle rising feedback combined with slowly
			changing modulation processing creates a
			dreamlike atmosphere reverberation.

Specifications

Input: 1/4"mono audio input jack *2 (1M ohms)

Output: 1/4"mono audio output jack *2 (510 ohms)

Number of effect saving slots: 14

Power requirement: 9V power supply (center negative)

Current draw: 300mA

*Notice: Recommended to use only the original power

supply included with the pedal. Using

third-party power supplies may cause noise

or other unexpected issues.

Dimension 75x115x33mm

Weight 0.334kg

Accessories: Owner's manual Power adapter

*Disclaimer: Parameter updates will not be notified separately.

SHENZHEN MOOER AUDIO CO. LTD

6F, Unit D, Jinghang Building, Liuxian 3rd Road,

Bao’an 71 District, Shenzhen, China. 518133

Made in China