MAP77
CanBus Vehicle Security System
User Manual
MONGOOSE MAP77 CANBUS
Vehicle Security System VSS
Features:
the MAP 77 V SS i s co nt roll ed by O EM r emot e con trol s (v ehic le's
or ig in al equi pmen t
tru nk re lea se bu tton lo gic (*O EM re mote trans mitt er op erate d),
moni tori ng of all doors , tru nk, b onne t swi tches ,
veh icl e in ter ior p rote cti on wh en us ed wi th Se nsor
automatic power window roll-up (*) when the VSS is armed (comfort
function),
VSS can be arme d witho ut: int eri or s enso r pr ot ecti on (*),
ad di tion al sen sor s (* ), p ower win dow rol l-up (*),
war nin g if door / tr unk / b onn et is open when arm ing (*) (door
aja r),
sel ect ab le s ile nt / aud ibl e (* ) c onfi rma ti on o f a rm ing and
di sarm ing ,
pas sive ar min g (*) w/wo auto mati c cen tra l doo r lo cki ng (* ),
ignition safety door lock (*) - automatic central door locking / unlocking
during drive
coded / uncoded (*) emergency override procedure without remote
transmitters,
Ser vice mod e
Warn ing i f th e ala rm was tri ggere d when di sarmin g the VSS,
st ate of th e s ys te m i s m emo ri sed in no n-v ol at ile me mor y an d i s
pr ese rv ed du rin g p ow er -of f,
the so ur ce o f 5 pre vio us ala rm cycl es i s k ept in no n-vo lati le
mem ory ,
com pat ib le w ith d iffe ren t ty pes of sire ns: B asic an d Ba tter y
ba ckup si ren,
REA RMI NG fu nctio n,
VALE T mo de - Vehic le Se curit y Sy stem tem porar y dis abled ,
PAN IC inp ut (* ) - p real ar m signa lisa tion inp ut,
IMPORTANT!
The (* ) symbol describes optional fu nction/feat ure of th e VSS which
is dependent on the vehicle model and VSS configuration.
ARMING THE MAP77 VSS
Press the LOCK button on the remote - direction indicators blink and single
siren chirp (*) confirms the vehicle security system is arming and the central door
locking is locked. The LED will light constantly and after 10 seconds it will start to
blink slowly.
ARMING WITH INTERIOR MOTION DETECTOR AND ADDITIONAL SENSOR DISABLED
If the MAP77 VSS is armed with any person or animal in the vehicle, their
movement will trigger the alarm. To avoid such situation, the system can be
armed without interior motion detector and additional sensors.
To do so, before a rming the system - press a nd hold the PA button u ntil the
LED starts to blink rapidly. E xit the vehicle, close all doors and press the LOCK
button of the remote - two siren chirps confirm arming without interior motion
detector and addi tional sensor. Direction indicators blink confirms the vehicle
security system arming and the central door locking is clo sed. The LED will light
constantly and after 10 seconds it will start to blink slowly.
DISARMING AND OPENING THE CENTRAL DOOR LOCKING SYSTEM
Press the UNLOCK button of the remote - blink of the direction indicators and
double siren chirp (*) confirms disarming o f VSS and unlocking central door
locking system. The status LED will start blinking until any door is opened and
then will go off.
If the alarm was triggered during the driver’s absence, the VSS signalises it
with three siren chirps.
IMPORTANT!
If after disarming n either doors nor trunk is opened within 30 seconds the
system rearms automatically.
TRUNK RELEASE BUTTON LOGIC
In case of remote control with trunk release button TRUNK RELEASE its press will
open the boot and turn off the protection on trunk switch, interior motion detector
and additional sensor. and the sliding doors (in Van vehicles - rear left and rear
right). That state is confirmed by fast blinking of the LED. Depending on the vehicle,
closing the boot/slide doors or press of the LOCK button on the OEM remote brings
the security system again into armed state, signalised by slow LED pulses.
IMPORTANT! This feature is car dependent.
RE ARM ING
After disarm, the LED will start blinking. If neither doors nor trunk were opened
within the specified time, the disarming is treated as accidental and the VSS will
rearm again, closing the central door locking system. If any door or trunk were
opened, the rearming countdown is cancelled and the LED goes off. Rearming
time can be configured to: 30, 60 or 90 seconds.
DOOR OPEN WARNING (WHEN ARMING) - DOOR AJAR
If any doors, bonnet or trunk is not closed when arming, the VSS signalises it
with three siren chirps. The system will be armed, but the opened door / bonnet
/ trunk will not be monitored (will not trigger the alarm).
USER MANUAL
ALARMING / DISARMING THE VSS DURING THE ALARM / PREALARM
If the VSS is armed and any door, trunk or bonnet switch, additional sensor,
ultrasonic motion detector or ignition is triggered, the VSS starts a 30-second alarming
cycle - blinking the direction indicator lights and emitting sounds with electronic siren.
From triggering of the alarm till disarming the system with remote the LED blinks quickly,
2 times faster than in untriggered armed mode. After 30 seconds, the system stops the
alarm cycle. Further triggering of sensors starts another alarm cycle. Every input can
cause up to 4 alarm cycles and then it is blocked.
During alarm cycle, pressing LOCK button ends the alarm, b ut the v ehicle
remains locked and the VSS remains armed. During alarm cycle, pressing
UNLOCK button stops the alarm, disarms the VSS and opens the vehicle. If the
PREALARM function is present, the device signals prealarm triggering by 4 siren c
hirps.
EMERGENCY DISARMING OF THE SECURITY SYSTEM
MAP77 CAN has a procedure of emergency disarming the security system in
case the remote control is inoperative or not available (not working or lost).
In order to disarm the system with PIN code:
1. Open the door with the key (the alarm will sound).
2. Turn the ignition on.
3. Press the PA button number of times equal to the first digit of your PIN
code (intervals between pressing of PA button have to be less than 2 seconds).
4. Wait 2 seconds - the VSS confirms entering of PIN code digit via 1
second LED blink.
5. Repeat steps 3-4 for each of the remaining 3 digits of your PIN code.
If the PIN code is correct the alarm will disarm itself
The default PIN is 1111. The code can be individually programmed for a given
car by installer during installation procedure.
PASSIVE ARMING (*) / AUTOMATIC CENTRAL DOOR LOCKING (*)
On a demand, the passive arming (*) with or without automatic central door
locking (*)can be enabled. Passive arming function arms (switches on) the VSS
automatically.
With the ignition off, opening and closing driver's door starts the timer of
passive arming procedure. it is signalled by a single siren chirp. 12sec. later, the
alarm arms automatically, signalling it with LED, siren chirp (*) and hazard lights.
The central door locks remain u nlocked driver can still get i nto the vehicle.
Passive arming can be stopped if the UNLOCK button is pressed in the 12sec.
period after closing driver's door. Cancel of passive arming is signalled by
double siren chirp - passive arming will not occur.
If the automatic central door locking (*) is enabled, the door locking occurs
8sec. after passive arming of the VSS and is signalled by single siren chirp.
During that 8 seconds period between pa ssive arming and automatic
locking, press of the LOCK button locks the vehicle (confirmed by single siren
chirp); press of the UNLOCK button disarms the VSS, unlocks the vehicle and
cancel the passive arming.
The sequence of events (first passive arming with chirp, then automatic
central door locking) prevents from locking the keys inside vehicle.
CODED PA BUTTON AUTHORISATION
N
The coded PA button authorisation procedure is common for authorising the
immobiliser function and anti-hijack function. If both functions are active, it is
enough to enter the code once - both immobiliser and anti-hijack will be
authorised. The number of tries is not limited.
LED signals that the immobiliser/antiihijack function is active.
Press the PA button number of times equal to the first digit of your
PIN code.
- after first press of PA button the LED goes off and stops signalling active state
of immobiliser/anti-hijack function.
- intervals between pressing of PA button have to be less than 2 seconds
Wait approx. 2 seconds - the VSS confirms entering the digit of PIN
code with short blink of LED.
Within 3 seconds, start entering 2nd digit of code with PA button.
Repeat the steps for digits 3 and 4.
If the PIN code entered is correct the LED will light-up for 2 seconds,
confirming the authorisation of immobiliser/anti-hijack function.
If the code was not correct, after 3 seconds the LED starts to display
the active state of immobiliser/anti-hijack function.
In case of mistake, wait 4 seconds until the LED starts to display the
active state of immobiliser/anti-hijack function and then start the sequence
from the beginning.
VAL ET MOD E
In case the car has to be left in a workshop, there is a possibility to set the VSS
in so-called valet mode. The staff of the service does not n eed to be informed
about the VSS, because it is disabled and thus, the alarm, the ANTI-HIJACK and
the IMMOBILISER functions do not work. The vehicle in valet mode is not
protected and the engine can always be started.
When entering valet mode, the VSS has to be disarmed and the ANTI-HIJACK
and IMMOBILISER functions have to be authorised.
Entering valet mode
1. Turn the ignition on.
2. Press the PA button 7 times (pause between press should be less
than 1 second).
3. The single blink of LED and 4 siren chirps confirm entering the valet mode.
Leaving valet mode
1. Press the PA button 7 times. (The ignition does not have to be on)
In valet mode, every attempt to arm the system with the remote or resetting
the power supply to the VSS is signalled with 4 siren chirps. The LED is constantly
off. If the OEM remote is used, only the central door locking i s closed, but the
VSS remains disarmed.
E
Loading...