M80 Series
MODELS:
M80i, M80S, M80GNZ, M80G
USER OPERATION MANUAL
All models certified to AS/NZS4601 1999 amendment 1
M80S certified to AS/NZS3749.1 2003 Class B
M80G/GNZ certified to AS/NZS3749.1 2003 Class A
These products should be installed according to the requirements of the
AS/NZS 3749.2 Installation Sta nd ar d.
Installation should only be carried out by suitably qualified persons.
References to alarm functions and siren/horn responses do not apply to model M80i.
REMOTE CONTROL
2 Supplied
BUTTON ‘THREE’
‘PANIC’
PRESS FOR 3 SECONDS TO SOUND THE
ALARM SYSTEM.
PRESS AGAIN TO CANCEL.
BUTTON ‘ONE’ THEN ‘THREE’
‘SENSOR BYPASS’
THIS DEACTIVATES ANY CO NNECTED
SENSOR.
ONLY DEACTIVATE SENSOR S TO
REDUCE THE POSSIBILITY O F FALSE
ALARMS.
TURBO TIMER
BUTTON ‘TWO’ & ‘THREE’ TOGETHER
PRESS WITH IGNI TION ON TO TURN THE
BUILT-IN TURBO TIMER ON/OFF.
See page 7
BATTERY REPLACEMENT
CR2032 LITHIUM BATTERIES ARE AVAILABLE FROM YOUR MONGOOSE
AGENT OR USUAL BATTERY OUTLET. PLEASE CHA NG E ANNUALLY OR IF
OPERATION BECOMES I NTERMITTENT.
BUTTON ‘ONE’
‘ARM or DISARM’
PRESS ONCE FOR 1SECOND
TO ARM OR DISARM T HE
SECURITY SYSTEM -
(DOORS WILL ALSO LOCK OR UNLOCK
IF THE CENTRAL LOCKING HA S BEEN
CONNECTED)
PRESS FOR 2~3 SECONDS IF TURBO
TIMER IS ON
BUTTON ‘TWO’
PRESS FOR 3 SECONDS FOR
‘AUXILIARY OUTPUT’ (EG: BOOT
RELEASE)
BUTTON ‘TWO’ THEN ‘ONE’
‘SILENT ARM or DISARM’
THIS SEQUENCE WILL SILENTLY
ARM OR DIS-ARM THE ALARM – NO SIREN
CHIRPS
CONTENTS
Automatic engine immobilisation.. 4 Arm condition memory............... 10
Arming………… …….................... 5 Noise pollution control......….…. 10
Open circuit bypass….…………… 5 Indicator flashing……………..… 11
Central locking........…............… .. 5 Dash mounted warning light….. 11
Disarming…………………………. 6 Chirp confirmation…................. 11
Security re-arm……………….….. 6 Car Finder & Panic...….......….. 12
Silent arm/disarm ……………….… 6 Boot release………….......….... 12
Bonnet, boot & doors……………… 6 Programme options..…............ 13/14
Built-in turbo timer…………………. 7 Remote controls………............ 14
2 stage impact sensor (excl’ M80i) 8 Remote code learning.............. 14/15
Glass break sensor……………….. 8 EMERGENCY OVERRIDE…… 16
Sensor disable...…………….......... 8 PIN code progr amming…….… . 17
Intrusion alert ……………….…….. 8 Testing your alarm…….………. 18
Optional extras……………………. 9
Battery back-up siren (M80S/G)... 10 Wiring , programming & warranty
Automat ic re-set………………….. 10 Proof of purchase
OPERATING YOUR VEHICLE SECURITY SYSTEM
AUTOMATIC ‘TRIPL E CIRCUIT’ ENGINE IMM O BILISATION
The engine always immobilises automatically 30 seconds after the ignition has been turned off.
When you turn the ignition OFF, the dashboard LED wil l start to fast flash for 30 seconds t o indicate
the automatic sequence has commenced. At the end of the 30 seconds, the siren will chirp once
(alarm models only), the indicators will flash once and the dashboard LED will slow flash as
confirmation of imm obi l isation.
Only the engine is immobil ised, the alarm system is not yet armed.
If an attempt is made to start the engine whilst immobilised, the siren will chirp a warning – fully
sounds if armed by remote.
ONCE IMMOBILISE D, P RES S BUTTON
ONE TO DISENGAGE THE ENG I NE IMMOBILISERS
NOTE: If the system has automat ically immobilised the engine and you now wis h to arm the security
system (& lock the doors), press button one twice.
The installer of this system will immobilise three of the following possible circuits to prevent engine
starting;
Starter motor
Ignition system
Electric fuel pump
Other engine controlling circ ui t
Ask the installer which ci rcuits are immobilised for future refer enc e.
4
ARMING
NORMAL OPERATION
Exit the vehicle and ensure all doors , bonnet & boot are closed.
Press remote button one for approximately 1 second (2+ seconds if turbo timer on).
To confirm arming, the indicators flash once, the siren chirps once and the dashboard
warning LED, will then slow flash.
If your vehicle has central locking and i t has been connected to this security system , t he
doors will lock at the same time as arming.
If the automatic engine immobiliser has activated before you wished to arm the system, press
button one twice – once to disengage the i mmobiliser and a second tim e to fully arm (and lock the
doors if connected) and immobilise the system. Note: The system can be programmed to arm
automatically 30 sec onds aft er t he l as t door is closed. See page 12.
OPEN CIRCUIT BYPASS
If any door, the bonnet or boot is left open when you arm the system , the siren will chirp once t o
signify the system is armed and then chirp again to inform you a circuit is still open. The dash
mounted LED will flash a code for 30 seconds showing you what is open (s ee page 10). If ignored
and not closed, that circuit will not be protected. The open circuit will automatically arm upon
closure.
CENTRAL LOCKING - addi ti o n al p arts, at extra cost, may be required.
This security system has built-in relays to operate a vehicles ’ ex is t i ng cent ral l ock i ng s yst em by remot e
control. When connected, the doors will lock or unlock at the same t ime as arming or disarming.
SILENT ARM (no siren chirps)
Press button two and then, within 2 seconds , button one to silently arm the system .
The chirps may be permanently turned off via the programming options – see your installer.
5
DISARMING
Press button one on the remote control to disarm the system.
The siren will chirp twic e and the indicators will flash twice t o c onfirm disarm.
The doors will unlock if the vehic l es’ central locking is connected to t he sec uri t y system.
If a door is not opened wit hin 30 seconds, the s ystem will automatically re-arm (& re-lock
if connected to your central l ocking) . See below.
SILENT DISARM (no siren chirps)
Press button two and then, within 2 seconds , button one to silently disarm the system .
The chirps may be permanently turned off via the programming opti ons – see your installer.
AUTOMATIC SECURITY RE-ARM
The alarm will autom atical ly fully re-arm (and re-lock the doors if connec ted) if it has been di sarmed
by remote but a door has not been opened within 30 sec onds . The light s flas h once as confi rmati on
of re-arming. This feature cannot be t urned of f .
If a door, bonnet or boot is opened after disarming, t he alarm will not re-arm and t he doors will not
re-lock. However, the engine will re-i m mobilise if the ignition is not turned ON withi n 30 s econds.
IGNITION, BONNET , BOO T & DOORS – 30 second siren – 60 second li g h t flash
When armed, the siren will s ound for 30 seconds and the indic ators will flash for 60 seconds when
any of these are triggered. If a door, bonnet or boot has been opened and lef t open, the siren will
sound for 90 seconds (3 x 30 seconds) and the indicators will flash. The open circuit will then be
bypassed.
(If programmed for NSW, the si ren wil l sound once only for 30 seconds)
The system does require your vehicle to be fitted with courtesy light door switches for these to
trigger the alarm. Fitti ng or replacing door switches will incur addit i onal charges.
6
BUILT-IN TURBO TIMER
The built-in turbo timer all ows the engi ne t o continue running (if installed for this feature) for a preprogrammed time after t he igni t i on has been turned off. This feature m ay be used to all ow t he
vehicles turbo/engine to cool down. In normal driv i ng sit uations and to save fuel, the turbo timer
should not be necessary.
The timer is programmabl e f or durat ion from 1 to 5 minutes - see ‘programm i ng’ .
To enable the turbo timer feature:- with the ignition on, press rem ote buttons 2 & 3 at the same time,
siren chirps once. The tim er function will now always be ON each time the v ehi cle is us ed.
To disable the timer:- repeat t he above procedure – siren chirps twic e – timer is now off.
To stop the engine if alread y running:- press buttons 2 & 3 at the same time
NOTE: When the engine is running, arming the alarm does not immedi at el y immobi li se the engine
or turn on any sensors. An intrus i on by opening any door, bonnet or boot will imm edi ately stop and
immobilise the engine and trigger t he al arm.
To arm with timer ON:-
Ensure the vehicle is in neutral gear or ‘park’ position and the handbrak e i s appli ed.
Turn the ignition off (engine rem ai ns running if timer is ON – engine stops if timer is OF F )
Exit the vehicle ensuring all doors, bonnet & boot are closed.
Arm the alarm by the remote – requires a longer press than normal (a couple of seconds).
After the programmed time, the engine stops, the immobilisers engage and sensors arm .
WHEN NOT TO USE THE TURBO TIMER
1. When this system has not been installed t o all ow f or an engi ne t urbo
2. When people or animals are still ins i de the vehicle
3. When doors or windows are to be left open
4. Is prohibited by country or state laws or by any other authority.
5. When doing so is likely to cause a risk or danger to others or property
6. When re-fuelling
7
2 S TAGE I MPACT/SHOCK SENSOR (M80S/G)
This sensor is designed to detec t impact to the vehicle such as to the bodywork or glass. It should
not be triggered by normal wind, or roc king motions.
If the sensor detects a light impact, the siren will sound a few warning chirps.
If the sensor detects a heavier impact, the analyser circuit will determine this and sound
the siren for 30 seconds and flash the lights.
The sensitivity level is set by the installer and should be at its optimum. Avoid over sensitivity as
people nearby may not respond due t o too many false alarm s. (This type of sensor may not preve nt
wheel theft, we therefore adv i se the fitment of locking wheel nuts)
GLASS BREAK SENSOR (M80G/GNZ models)
This sensor is designed to trigger the alarm by detect ing the sound of actual glass breakage. The
sensitivity level is set by the i ns taller and should be at its optimum.
SENSOR DISABLE BY REMOTE (EXCEPT M80i)
There are times when you may wish to deact ivate sensors, such as the impac t sensor, to prevent
false alarms. To turn sens ors off (any attached sens or will be disabled), but ar m the bonnet, boot
and doors and immobili se the engine, press button one followed b y button two. You will hear the
siren chirp for arming followed by a tone indic ating the sensors are turned off. The sensor is reactivated upon subsequent arming.
INTRUSION ALERT & LED DIAGNOSTICS
Upon disarming, if the s iren chirps 4 times and the indicators flash 3 times the system tells you
that it has been triggered.
The LED flash codes on page 11 show which c i rc ui t has been triggered.
8
OPTIONAL ACCESSORIES
GPS TRACKING
Mongoose can provide var ious GPS tracking options whether it is to recover a stolen vehicl e or for
vehicle and people management. Mongoose offers models that are completely controlled and
monitored by an iPhone or similar, or vi a our GPRS webs it e, provi de data a nd route loggi ng wi th ful l
reporting options.
GSM TEXT PAGER (MTP4)
If your alarm is activated or your vehicle battery runs low, the text pager will sends you an alert
message to your mobile phone.
ULTRASONIC SENSOR (MUM 80)
The ultrasonic sensor f ill the interior of your vehicle with high frequ ency sound and is designed to
trigger the alarm when the interior environment changes. Possible changes are the breaking or
removal of glass, a door being opened, or ev en strong wind through a slightly open window.
Ultrasonic’s are not rec ommended for soft top vehicles or vehicles where air movement is likely
within the vehicle.
MICROWAVE SENS OR (M M W80 D)
The microwave sensor is designed to trigger the alarm when a microwav e f i el d registers physical
movement. 2 fields are generated, one out s i de the vehicle to give perimet er prot ection, and one
inside to give interior protection.
Note: As the microwave produces circular protective fields, some areas of large vehicles may not be protected.
ELECTRONIC TILT SENSOR (MTS2000)
These sensors are designed to trigger the alarm system if it registers a tilt of the vehicle greater than 2
degrees which could occur if the vehicle is jacked up to remove the wheels.
9
Loading...