M80 Series
MODELS:
M80i, M80S, M80GNZ, M80G
USER OPERATION MANUAL
All models certified to AS/NZS4601 1999 amendment 1
M80S certified to AS/NZS3749.1 2003 Class B
M80G/GNZ certified to AS/NZS3749.1 2003 Class A
These products should be installed according to the requirements of the
AS/NZS 3749.2 Installation Sta nd ar d.
Installation should only be carried out by suitably qualified persons.
References to alarm functions and siren/horn responses do not apply to model M80i.
REMOTE CONTROL
2 Supplied
BUTTON ‘THREE’
‘PANIC’
PRESS FOR 3 SECONDS TO SOUND THE
ALARM SYSTEM.
PRESS AGAIN TO CANCEL.
BUTTON ‘ONE’ THEN ‘THREE’
‘SENSOR BYPASS’
THIS DEACTIVATES ANY CO NNECTED
SENSOR.
ONLY DEACTIVATE SENSOR S TO
REDUCE THE POSSIBILITY O F FALSE
ALARMS.
TURBO TIMER
BUTTON ‘TWO’ & ‘THREE’ TOGETHER
PRESS WITH IGNI TION ON TO TURN THE
BUILT-IN TURBO TIMER ON/OFF.
See page 7
BATTERY REPLACEMENT
CR2032 LITHIUM BATTERIES ARE AVAILABLE FROM YOUR MONGOOSE
AGENT OR USUAL BATTERY OUTLET. PLEASE CHA NG E ANNUALLY OR IF
OPERATION BECOMES I NTERMITTENT.
BUTTON ‘ONE’
‘ARM or DISARM’
PRESS ONCE FOR 1SECOND
TO ARM OR DISARM T HE
SECURITY SYSTEM -
(DOORS WILL ALSO LOCK OR UNLOCK
IF THE CENTRAL LOCKING HA S BEEN
CONNECTED)
PRESS FOR 2~3 SECONDS IF TURBO
TIMER IS ON
BUTTON ‘TWO’
PRESS FOR 3 SECONDS FOR
‘AUXILIARY OUTPUT’ (EG: BOOT
RELEASE)
BUTTON ‘TWO’ THEN ‘ONE’
‘SILENT ARM or DISARM’
THIS SEQUENCE WILL SILENTLY
ARM OR DIS-ARM THE ALARM – NO SIREN
CHIRPS
CONTENTS
Automatic engine immobilisation.. 4 Arm condition memory............... 10
Arming………… …….................... 5 Noise pollution control......….…. 10
Open circuit bypass….…………… 5 Indicator flashing……………..… 11
Central locking........…............… .. 5 Dash mounted warning light….. 11
Disarming…………………………. 6 Chirp confirmation…................. 11
Security re-arm……………….….. 6 Car Finder & Panic...….......….. 12
Silent arm/disarm ……………….… 6 Boot release………….......….... 12
Bonnet, boot & doors……………… 6 Programme options..…............ 13/14
Built-in turbo timer…………………. 7 Remote controls………............ 14
2 stage impact sensor (excl’ M80i) 8 Remote code learning.............. 14/15
Glass break sensor……………….. 8 EMERGENCY OVERRIDE…… 16
Sensor disable...…………….......... 8 PIN code progr amming…….… . 17
Intrusion alert ……………….…….. 8 Testing your alarm…….………. 18
Optional extras……………………. 9
Battery back-up siren (M80S/G)... 10 Wiring , programming & warranty
Automat ic re-set………………….. 10 Proof of purchase
OPERATING YOUR VEHICLE SECURITY SYSTEM
AUTOMATIC ‘TRIPL E CIRCUIT’ ENGINE IMM O BILISATION
The engine always immobilises automatically 30 seconds after the ignition has been turned off.
When you turn the ignition OFF, the dashboard LED wil l start to fast flash for 30 seconds t o indicate
the automatic sequence has commenced. At the end of the 30 seconds, the siren will chirp once
(alarm models only), the indicators will flash once and the dashboard LED will slow flash as
confirmation of imm obi l isation.
Only the engine is immobil ised, the alarm system is not yet armed.
If an attempt is made to start the engine whilst immobilised, the siren will chirp a warning – fully
sounds if armed by remote.
ONCE IMMOBILISE D, P RES S BUTTON
ONE TO DISENGAGE THE ENG I NE IMMOBILISERS
NOTE: If the system has automat ically immobilised the engine and you now wis h to arm the security
system (& lock the doors), press button one twice.
The installer of this system will immobilise three of the following possible circuits to prevent engine
starting;
Starter motor
Ignition system
Electric fuel pump
Other engine controlling circ ui t
Ask the installer which ci rcuits are immobilised for future refer enc e.
4
ARMING
NORMAL OPERATION
Exit the vehicle and ensure all doors , bonnet & boot are closed.
Press remote button one for approximately 1 second (2+ seconds if turbo timer on).
To confirm arming, the indicators flash once, the siren chirps once and the dashboard
warning LED, will then slow flash.
If your vehicle has central locking and i t has been connected to this security system , t he
doors will lock at the same time as arming.
If the automatic engine immobiliser has activated before you wished to arm the system, press
button one twice – once to disengage the i mmobiliser and a second tim e to fully arm (and lock the
doors if connected) and immobilise the system. Note: The system can be programmed to arm
automatically 30 sec onds aft er t he l as t door is closed. See page 12.
OPEN CIRCUIT BYPASS
If any door, the bonnet or boot is left open when you arm the system , the siren will chirp once t o
signify the system is armed and then chirp again to inform you a circuit is still open. The dash
mounted LED will flash a code for 30 seconds showing you what is open (s ee page 10). If ignored
and not closed, that circuit will not be protected. The open circuit will automatically arm upon
closure.
CENTRAL LOCKING - addi ti o n al p arts, at extra cost, may be required.
This security system has built-in relays to operate a vehicles ’ ex is t i ng cent ral l ock i ng s yst em by remot e
control. When connected, the doors will lock or unlock at the same t ime as arming or disarming.
SILENT ARM (no siren chirps)
Press button two and then, within 2 seconds , button one to silently arm the system .
The chirps may be permanently turned off via the programming options – see your installer.
5
DISARMING
Press button one on the remote control to disarm the system.
The siren will chirp twic e and the indicators will flash twice t o c onfirm disarm.
The doors will unlock if the vehic l es’ central locking is connected to t he sec uri t y system.
If a door is not opened wit hin 30 seconds, the s ystem will automatically re-arm (& re-lock
if connected to your central l ocking) . See below.
SILENT DISARM (no siren chirps)
Press button two and then, within 2 seconds , button one to silently disarm the system .
The chirps may be permanently turned off via the programming opti ons – see your installer.
AUTOMATIC SECURITY RE-ARM
The alarm will autom atical ly fully re-arm (and re-lock the doors if connec ted) if it has been di sarmed
by remote but a door has not been opened within 30 sec onds . The light s flas h once as confi rmati on
of re-arming. This feature cannot be t urned of f .
If a door, bonnet or boot is opened after disarming, t he alarm will not re-arm and t he doors will not
re-lock. However, the engine will re-i m mobilise if the ignition is not turned ON withi n 30 s econds.
IGNITION, BONNET , BOO T & DOORS – 30 second siren – 60 second li g h t flash
When armed, the siren will s ound for 30 seconds and the indic ators will flash for 60 seconds when
any of these are triggered. If a door, bonnet or boot has been opened and lef t open, the siren will
sound for 90 seconds (3 x 30 seconds) and the indicators will flash. The open circuit will then be
bypassed.
(If programmed for NSW, the si ren wil l sound once only for 30 seconds)
The system does require your vehicle to be fitted with courtesy light door switches for these to
trigger the alarm. Fitti ng or replacing door switches will incur addit i onal charges.
6
BUILT-IN TURBO TIMER
The built-in turbo timer all ows the engi ne t o continue running (if installed for this feature) for a preprogrammed time after t he igni t i on has been turned off. This feature m ay be used to all ow t he
vehicles turbo/engine to cool down. In normal driv i ng sit uations and to save fuel, the turbo timer
should not be necessary.
The timer is programmabl e f or durat ion from 1 to 5 minutes - see ‘programm i ng’ .
To enable the turbo timer feature:- with the ignition on, press rem ote buttons 2 & 3 at the same time,
siren chirps once. The tim er function will now always be ON each time the v ehi cle is us ed.
To disable the timer:- repeat t he above procedure – siren chirps twic e – timer is now off.
To stop the engine if alread y running:- press buttons 2 & 3 at the same time
NOTE: When the engine is running, arming the alarm does not immedi at el y immobi li se the engine
or turn on any sensors. An intrus i on by opening any door, bonnet or boot will imm edi ately stop and
immobilise the engine and trigger t he al arm.
To arm with timer ON:-
Ensure the vehicle is in neutral gear or ‘park’ position and the handbrak e i s appli ed.
Turn the ignition off (engine rem ai ns running if timer is ON – engine stops if timer is OF F )
Exit the vehicle ensuring all doors, bonnet & boot are closed.
Arm the alarm by the remote – requires a longer press than normal (a couple of seconds).
After the programmed time, the engine stops, the immobilisers engage and sensors arm .
WHEN NOT TO USE THE TURBO TIMER
1. When this system has not been installed t o all ow f or an engi ne t urbo
2. When people or animals are still ins i de the vehicle
3. When doors or windows are to be left open
4. Is prohibited by country or state laws or by any other authority.
5. When doing so is likely to cause a risk or danger to others or property
6. When re-fuelling
7
2 S TAGE I MPACT/SHOCK SENSOR (M80S/G)
This sensor is designed to detec t impact to the vehicle such as to the bodywork or glass. It should
not be triggered by normal wind, or roc king motions.
If the sensor detects a light impact, the siren will sound a few warning chirps.
If the sensor detects a heavier impact, the analyser circuit will determine this and sound
the siren for 30 seconds and flash the lights.
The sensitivity level is set by the installer and should be at its optimum. Avoid over sensitivity as
people nearby may not respond due t o too many false alarm s. (This type of sensor may not preve nt
wheel theft, we therefore adv i se the fitment of locking wheel nuts)
GLASS BREAK SENSOR (M80G/GNZ models)
This sensor is designed to trigger the alarm by detect ing the sound of actual glass breakage. The
sensitivity level is set by the i ns taller and should be at its optimum.
SENSOR DISABLE BY REMOTE (EXCEPT M80i)
There are times when you may wish to deact ivate sensors, such as the impac t sensor, to prevent
false alarms. To turn sens ors off (any attached sens or will be disabled), but ar m the bonnet, boot
and doors and immobili se the engine, press button one followed b y button two. You will hear the
siren chirp for arming followed by a tone indic ating the sensors are turned off. The sensor is reactivated upon subsequent arming.
INTRUSION ALERT & LED DIAGNOSTICS
Upon disarming, if the s iren chirps 4 times and the indicators flash 3 times the system tells you
that it has been triggered.
The LED flash codes on page 11 show which c i rc ui t has been triggered.
8
OPTIONAL ACCESSORIES
GPS TRACKING
Mongoose can provide var ious GPS tracking options whether it is to recover a stolen vehicl e or for
vehicle and people management. Mongoose offers models that are completely controlled and
monitored by an iPhone or similar, or vi a our GPRS webs it e, provi de data a nd route loggi ng wi th ful l
reporting options.
GSM TEXT PAGER (MTP4)
If your alarm is activated or your vehicle battery runs low, the text pager will sends you an alert
message to your mobile phone.
ULTRASONIC SENSOR (MUM 80)
The ultrasonic sensor f ill the interior of your vehicle with high frequ ency sound and is designed to
trigger the alarm when the interior environment changes. Possible changes are the breaking or
removal of glass, a door being opened, or ev en strong wind through a slightly open window.
Ultrasonic’s are not rec ommended for soft top vehicles or vehicles where air movement is likely
within the vehicle.
MICROWAVE SENS OR (M M W80 D)
The microwave sensor is designed to trigger the alarm when a microwav e f i el d registers physical
movement. 2 fields are generated, one out s i de the vehicle to give perimet er prot ection, and one
inside to give interior protection.
Note: As the microwave produces circular protective fields, some areas of large vehicles may not be protected.
ELECTRONIC TILT SENSOR (MTS2000)
These sensors are designed to trigger the alarm system if it registers a tilt of the vehicle greater than 2
degrees which could occur if the vehicle is jacked up to remove the wheels.
9
BATTERY BACK-UP SIREN (M80S/G/GNZ)
These models have a battery back-up siren. Vehicle battery disconnection will cause the battery
back-up siren to sound. The siren c an be t urned of f wi t h t he special keys provided.
The siren is mounted under t he bonnet and should be situated in a plac e to protect it from heat and
water damage. Driving through deep water or puddles may cause water splashes, so caution is
advised. Please check t hat the siren has been mounted in s uch a position so as to avoi d damaging it.
If washing the engine bay, c over the siren with a plastic bag t o prevent water damage. Heat or water
damage is not covered by the warranty.
AUTOMATI C RE-SET
Upon an intrusion (ie; doo r opened and closed), the siren will s ound for 30 seconds, after which i t
will stop and reset to the arm ed pos i tion. It wil l then re-t rigger on t he next intrusion.
If a door is left open, t he siren will sound for 3 x 30 seconds and then that individual ci rcuit will be
bypassed to avoid unnecessary noise.
(NSW, one sounding only - must be manually re-set after first trigger)
ARM CONDITION MEMORY
Should the vehicle batt ery be disconnected, the system memorises the las t set position of the alarm.
If the alarm was disarm ed prior to battery disconnection, rec onnection does not cause t he alarm to
sound. If the battery was disconnected whilst the system was armed, reconnection will return the
system to the armed state.
NOISE POLLUTI ON CO NT ROL
To reduce noise nuisanc e and possible fals e alarms, the system will isolate an indi vidual circuit i f it
is triggered more than three times in succession or is left open.
(Eg: 3 x bonnet, 3 x boot, 3 x doors, 3 x ignition, 3 x impact sensor, 3 x other sensor)
Reset by remote by disarming and then re-arming. Turn ignition ON/OFF to re-set LED intrusion
codes.
10
INDICATOR FLASHING
When the siren sounds, the indi cators flash simultaneously.
The indicators will als o flash on arming and disarming the system.
a) 1 Flash - Armed.
b) 2 Flash - Disarmed.
c) 3 Flash - Di s arm ed and previously triggered.
d) On permanently – Open c i rc ui t after arming, or Perimeter Nite Lite i s on
DASH MOUNTED LED WARNING LIGHT
The LED shows the status of the alarm , intrusion and any open circuit when arm ing.
a) Fast flashing - 30 second countdown of automatic functions.
b) Slow flashing - system armed.
c) LE D of f - system of f, s houl d onl y oc c ur i f the vehicle battery is flat.
d) On permanently - in remote code learning mode.
e) 1 flash, pause, 1 flash, etc - bonnet is open or triggered.
f) 2 flash, pause, 2 flash, etc - boot i s open or triggered.
g) 3 flash, pause, 3 flash, etc - a door is open or triggered.
h) 4 flash, pause, 4 flash, etc - impact sensor (white sensor port) has been triggere d.
i) 5 flash, pause, 5 flash, etc - engine start attempted.
j) 6 flas h, pause, 6 flash, etc - glass break (green sensor port) triggered.
WHAT THE CHIRPS MEAN
a) 1 Chirp - Arm.
b) 1 Chirp/short siren - Indic ates an open c i rc ui t during arming.
c) 2 Chirps - Disarmed.
d) 4 Chirps - Disarming and indicates that the alarm has been triggered.
e) Continual chirps - Igniti on has been turned on when the engine is immobil ised.
11
PANIC BY REMOTE (in eit her armed or disarmed state)
In the event of personal attack, or you suspec t that your vehicle is being tampered with, the alarm
can be ‘panicked’ by pres sing butt ons one and two at the same tim e on the remot e for more than 3
seconds. The siren will s ound and the indicators will flash.
Cancel the panic, by pressi ng bot h but t ons again.
Pressing button one whils t the siren is sounding will either arm or disarm the system depending on
the prior armed/disarm ed st at e.
VEHICLE LIGHTS ON WARNING
If the lights are on when you arm the system, the siren will chirp once and then briefly produces a
different sound as a warning.
If you intended to leave the light s on, ignore this warning.
This helps to prevent your car battery going flat if you accidentally left the vehicle lights on when
exiting your vehicle.
AUXILIARY CHANNEL 2 OUT PUT (EG: BOOT RELEASE) – OPTI ON AL CONNECTION
The system has an auxiliary pulse output which can be used, for example, to control a vehicle’s
electric boot release (f the vehicle is equipped). The out put can be used for other purpos es, please
discuss with your installer. This will usually incur additional charges.
Example of remote boot release;
Press button two on the remote for 3 seconds and t he boot wil l unl ock and open
The boot trigger circuit and int eri or s ensors (if fitted) will be bypassed
Upon closing the boot the bypass ed circuits will re-arm automatically
12
PROGRAMMABLE OPTIONS
These should only be changed by your installer.
AUTOMATIC (LAST DOO R) ARMING (default = OFF) – also OFF when turbo timer is on
When programmed ON, the alarm will arm automatically 30 seconds af ter the last door is closed.
If the engine immobilises prior to the opening and closing of a door, this feature will
commence and the LED will f ast flash when you close the last door.
The doors will not lock t o prevent the keys being lock ed inside unless option 2 above is
also turned on.
AUTOMATIC DOOR LOC K (d efau lt = OFF) - also OFF when turbo timer is on
The doors will lock autom atic al l y 30 seconds after the last door is closed.
WARNING: DO NOT LEAV E THE KEYS IN THE CAR !
This feature only operates if ‘ l ast door arming’ above has been programm ed ON.
IGNITION SAFETY DOOR LOCK (default = OF F ) - also OFF when turbo timer is on
If the system has been connected to a vehicl es’ central locking, the doors will lock 3 seconds after
the ignition is switc hed ‘on’ and unloc k immediately when the ignition is turned ‘off’.
If a door is left open whilst starti ng t he engi ne t hi s feature will be bypassed.
SIREN CHIRPS (defau lt = ON)
The chirps can be permanently turned off . Only the indicat ors confi rm the arm ing and disarm ing. W e
suggest that you use the ‘silent arming by remote’ feature as an alternative to turning them off
permanently as it is des irable for the system to chirp in public pl aces to warn others that you have a
security device fitt ed to your vehi c l e.
The siren chirp for the automatic engine immobiliser cannot be turned of f .
13
NSW SIREN TIMING (default = OFF)
It is a mandatory requirement i n New S out h Wales, Australia, for vehicle al arm systems to sound the
siren for one cycle of 30 seconds only before it is re-set manually by remote control. With this
feature turned on, the indicators will flash for any subsequent trigger.
PERIMETER NITE-LITE (default = OFF)
Upon disarming, the indicators will stay permanently lit for 15 seconds to provide perimeter
illumination. Ask the inst aller to verify that the power consumption of all the indicat ors is within the
tolerance of this product- maximum 8 amps per side.
SIREN/HORN OUTPUT (default = siren)
This programme allows f or connec tion to a vehicle horn. The output is then puls ed.
DOOR DIAGNOSTICS (d efau lt = ON)
This is factory set to ON. If for exam ple a door is left open when arming, the siren chirps once for
ARM then after a short paus e, c hirps a sec ond tim e to signi fy a circ uit i s open. Som e vehic les which
have ‘dome light delay’ may give a fals e signal – this feature should then be prog ram med OFF.
TURBO TIMER RUN TIME (defau lt = 2 minutes)
This allows an engine to rem ain running from it s bu ilt-in timer. The programme allows for an engine
running time of 1, 2, 3, 4 or 5 mi nutes. This programme only adjus ts the engine running time, see
page 7 for on/off function
COURIER MODE / TURB O I NT ERFACE FUNCTION (default = O F F )
This allows the alarm to be armed with the engine running by an aftermarket turbo timer or to al l ow
for applications such as ‘courier run on’.
An alarm trigger will stop the engine immediately.
14
ROLLING CODE (RANDO M ENCRYPTION) REMOT E CONTROLS
Two remote controls are supplied with the s ystem which enabl e you to arm and disarm your s ecuri ty
system.
The remote security code of your alarm system changes each time you press the remote button.
This coding system is referred to as Rolling Code and is completely random therefore eliminating
the possibility of anyone recordi ng i t (c ode grabbi ng).
The batteries in the remote controls should be changed when you notice any of the following;
System does not respond to the remot e signal
Operation is intermittent
Reduced operating range
The remote LED fails to light
Replace batteries annually. Uses CR2032
If the remote gets wet due to submersion, immediately dismantle, remove the battery and dry as
soon as possible. If submersed in salt water, rinse in fresh water and dry.
Water ingress and any subsequent remote failure is not covered under the warranty terms.
CODE LEARNING NEW REMOTES TO YOUR ALARM
The main alarm module has a l earning capacity to memorise up to four rem ote controls.
If you wish to add further rem otes or a rem ote has t o be replaced, the new rem ot e needs t o be code
learnt into the main module. If for instance you have lost a remote and are fearful that som eone may
try to use it, the lost remote can be deleted f rom memory so it cannot be used.
An irregular or interruption to the vehicle’s power s upply may cause loss of remote memory. If your
alarm fails to respond to the remote try re-learning them, or s ee your Mongoos e dealer.
15
REMOTE CODE LEARNI NG co n t’
Disarm the system
Open the drivers door and leave open
Within 15 seconds, turn the igni t i on ON/ OF F 3 t imes, 1~1.5 second apart
The siren will chirp 3 times, the indicators will flash 3 times to conf irm you have entered
remote code learning m ode. (no c hi rps on M80i unless siren/horn c onnec ted)
Press button one on the first remote – siren will chirp once as confirmation of reception
Press button one on the second remote – siren will chirp twice as conf irm ation of reception
Repeat for up to four remotes (siren will chirp 3 times for the third and 4 times for the
fourth).
Leave the system for 10 seconds or turn t he ignit ion on to end c ode learni ng m ode. This is
confirmed by three fast c hirps and l i ght f l ashes.
NOTE: When learning a new replacement or additional remo te, the original remote(s) m ust be
re-learnt or they will be erased from mem o ry an d will not operate this system.
To delete a remote from memory:
If you lose a remote, it is recommended t hat it is deleted from m emory so someone else c annot use
it. Enter learning mode as detailed above and memorise the existing remote(s) once. The lost
remote is now deleted. When a replacem ent is obtained, learn both the existing and new remotes
into memory as detailed abov e.
16
EMERGENCY OVERRIDE – 4 DIGIT PIN CODED
If all remotes are lost or inoperable, t he system can be disarmed by
entering your the unique 4 digit P IN code issued with this product.
KEEP THE CARD IN A SAFE PLACE – NOT IN THE VE HICLE !
Following is an exampl e using PIN code 4525
The code is entered by turning the i gni t i on ON or OFF in sequence with the dash mounted LED.
1) Ignition ON - LED will light permanently to commence override.
2) Ignition OFF - LED will start flashing. Count the num ber of f l ashes for the first number.
3) Ignition ON - after 4 flashes (1
st
number of the example). The LED will light.
4) Ignition OFF - count the number of flashes.
5) Ignition ON - after 5 flashes (2
nd
number).The LED will light.
6) Ignition OFF - count the number of flashes.
7) Ignition ON - after 2 flashes (3
rd
number). The LED will light.
8) Ignition OFF - count the number of flashes.
9) Ignition ON - after 5 flashes (4
th
number).
10) The system will now disarm an d the vehicl e can be started .
Note: If your PIN code contains a “0”, this equals ‘10’.
Should you miss the LED flashes or ent er a digi t i ncorrectly, wait for 11 flashes and sim ply repeat
the procedure from step 1).
This system will always automatically immobilise the engine ev ery time the ignition is turned off. Thi s
override sequence will have to be used until the remotes are repaired or replac ed.
17
EMERGENCY
4 DIGIT PIN CODE OVERRIDE
PLEASE KEEP THIS C ARD IN A SAFE PLACE
BUT BE READILY AVAILABLE SHOULD YO U
NEED TO USE THE OVERRIDE PROCEDURE
DO NOT LOSE THIS CARD
PIN CODE:
OVERRIDE PIN CODE P ROGR AMMI NG
Your security system is pre-programmed with a unique 4 digit PIN code as shown on the ‘PIN code
card’. You may wish to have your own code programmed to a number that is easier to remember.
Once changed, the factory setting i s p ermanently erased.
1 Disarm the system using the rem ote control.
2 Disconnect all power feeds i ncluding the central locking connections to this system for
10 seconds (or disconnect the car battery – radio pre-sets /c ode wi l l hav e t o be re-set).
3 Reconnect the power and turn the igni t i on ON t hen OFF once.
4 Open & close the door (or press door s wi t ch) 5 times and leave closed.
The siren will give one long chi rp and the l i ght s will stay on to show learning mode.
If the code is, for example, 2-3-3-4
5 Turn ignition ON.
The LED lights for 3 sec onds to show the start of the learnin g sequence. The LED will then
start to slow flash.
6 Allow the LED to flash twice for t he f i rst di gi t (2), then turn i gni t i on OF F .
The LED will light for 2 seconds to c onf i rm 1
st
digit input.
7 Turn the ignition ON and the LED s t art s t o slow f l ash again.
8 Repeat steps 6 & 7 for the 2
nd
, 3rd & 4th digits.
9 After the 4
th
digit is accepted the PIN code learning programme will cease.
(Turning OFF the igniti on & opening a door will al s o cancel this learning mode)
ARM THE SYSTEM AND TEST THE OVERRIDE PIN CODE FOR CORRECT OPERATION.
10 A mend the PIN code card with the new number, but do not l eave in the vehicle !
18
TESTING YOUR ALARM
We strongly recommend that you frequently test your alarm.
1) Without disarming the system, unlock and open a do or with the ignition ke y - the alarm should
sound, excluding model M 80i. Check all other doors, bonnet and boot by the same procedure.
2) Check the impact sensor, M80S/G, by giving the vehicle varying degrees of impact - be careful
to do this on areas of the vehicle not likely to be damaged by impact. Light impacts should
chirp the siren whilst heavier impacts should fully sound the s i ren.
3) Check the glass break sensor, M80G, by tapping the glass with a 50 cent coin. Varying
degrees of tapping should be tried to see the level of sensitivity. B e careful not to break the
glass.
4) Enter the vehicle and shut all doors, arm the s ystem by remote and tr y to start the engine to
test the engine immobil iser - i t shoul d not s tart and the siren (if fitted) should sound.
5) To test the optional ultrasonic sensors, if fitted, enter the vehicle, shut all doors and windows,
arm the system and allow it t o st abi l ise for 10~20 seconds. Now wave or clap your hands – the
alarm should sound.
6) To test the optional microwave sensor, if fitted, arm the system and wait at least 10~20
seconds for the sens or to stabilise. Moving a hand over the outside of side windows should
chirp the siren.
To test the perimeter field size, repeat this movement on the outsi de of al l glas s areas.
To test the interior, leave a window op en when arming and reach in and wave an arm around
- the siren should fully sound.
19
WIRING INFORMATION: Installation to be carri ed out by suitably qualified persons.
MAIN MODULE The wires printed for the funct ion;
1) (+) INDICATOR – 8 amp FUSED 1) ORANGE – UNLOCK – NO FUSED
2) (+) 12V FUSED 2) BLUE – UNLOCK – COMMON
3) (+) INDICATOR – 8 amp FUSED 3) BROWN – UNLOCK – NC
4) (-) DOME LIGHT 4) BLACK - GROUND WHEN ARMED
5) (+) SIREN 5) WHITE – LOCK – NC
6) (-) BONNET TRIGGER 6) GREEN – LOCK - COMMON
7) (-) BOOT TRIGGER 7) PURPLE – LOCK – NO FUSED
8) (-) GROUND 8) YELLOW - 2 STAGE UNLOCK
9) (-) GROUND
10) (+) PARK LIGHT INPUT (for lights on warning)
11) (-) Ch 2
12) (+) DOOR TRIGGER
13) (-) DOOR TRIGGER
14) (+) IGNITION FUSED
IMMOBILISER CIRCUIT #1, #2, #3 PAIRED WIRES – 2 pairs for each circuit
WIRING - use immobiliser circuit #1 for turbo timer
See next page for built-in turbo timer wiring.
SIREN / BONNET
GN
BONNET
BATTERY BACK-UP
GN
STANDARD
BONNET
BUILT-IN TURBO TIMER WIRING
Must use immobiliser circuit # 1 for i gnition
Ignition barrel
Ignition sense wire
+12v permanent
CUT ignition wire
Immobiliser circuit #1
Use immobiliser circuits #2 & #3 for other circuits
POWER
TRIGGER
TRIGGER
BONNET
CENTRAL LOCKING CONNECTION OPTIONS
UNLOCK
POSITIVE OR NEGA TIVE SWITCHING
.
NO
NO
LOCK
PURPLE - LOCK
WHITE - LOCK
GREEN - LOCK
ORANGE - UNLOCK
BROWN - UNLOCK
BLUE - UNLOCK
CONNECT TO G RO UND FO R NE GATIVE SWITCHING
OR
TO DOOR
PURPLE - LOCK
WHITE - LOCK
ORANGE - UNLOCK
BROWN - UNLOCK
BLUE - UNLOCK
.
+12 VOLTS (insert fuses if none supplied)
TO CAR
TO DOOR
REVERSE POLARI TY
GREEN - LOCK
ADD ON SOLENOID
GREEN - LOCK
PURPLE - LOCK
WHITE - LOCK
ORANGE - UNLOCK
BROWN - UNLOCK
BLUE - UNLOCK
+12 VOLT (insert fuses if none
supplied)
.
.
TO CDL
GREEN - LOCK
PURPLE - LOCK
WHITE - LOCK
ORANGE - UNLOCK
BROWN - UNLOCK
BLUE - UNLOCK
.
NO
NO
SINGLE WIRE SWITCHING
CDL CONTROL
TO
SWITCH
CUT FACTORY
WIRE
.
.
BLACK/YELLOW
GREEN - LOCK
PURPLE - LOCK
WHITE - LOCK
ORANGE - UNLOCK
BROWN - UNLOCK
BLUE - UNLOCK
CLOSE TO PUMP
YELLOW
BROWN
R
E
D
B
L
U
E
G
R
E
E
BLUE
GREEN
12 v
12 v
FACTORY VACUUM
VACUUM PUMP
PROGRAM ALARM
FOR 3 SECOND PULSE
NOTE2: MOST MODERN
SYSTEMS NOW USE 1
NEGATIVE SWITCHING
.
.
.
.
GROUND
USES OPEN CIRCUIT TO LOCK
AND NEGATIVE PULSE TO
PROGRAMME OPTIONS (no chirps for M80i unless siren/horn connected)
1. Ensure the drivers door is open
2. Within 15 seconds of opening the door, turn the ignition ON/OFF the number of times
relative to the programm e chart (eg: 4 t imes for ignition door lock).
3. S iren will then chirp the same number of times as the programme number and the lights
also flash the same number of t imes
4. Press button one to turn the feature "ON" - s i ren c hi rps once – lights flash once
5. Press button two to turn feature "OFF" - s iren chirps twice – lights flash twice
6. Leave system for 10 seconds - syst em f ast chirps 3 times (lights flash 3 times) to signify
end of programming
* = FACTORY DEFAULT
FEATURE
ARM BUTTON (ON)
BOOT BUTTON (OFF)
3
REMOTE CODE LEARNING
4
IGNITION DOOR LOCK
ON
OFF*
5
SIREN CHIRPS
ON *
OFF
6
TURBO RUN TIME
Each press =
1 MINUTE (max’ 5 mins)
n/a
7
LAST DOOR ARMING
ON
OFF *
8
DOOR DIAGNOSTICS
ON *
OFF
10
SIREN OR HORN
SIREN *
HORN
11
CDL PULSE
0.8 Secs *
3.5 Sec.
12
NSW SIREN TI MING
ON
OFF *
13
AUTO DOOR LOCK
ON
OFF *
14
PERIMETER NITE LITE
ON
OFF *
15
TURBO INTERFACE
ON
OFF *
WARRANTY CONDITIONS
PRODUCT WARRANTY
Mongoose warrants for a period of 60 months (5 Years) that it will make good without charge at Mongoose’s discretion, by repair or replacement
with a reasonable equivalent, any def ec t in the product providing that;
(a) the defect has been not ified as soon as it is noticed to an authorised Mongoose installation centre, distributor or agent (in the first instance t o
the original installati on c entre).
(b) the alarm is less th an 5 years of age from the date of s ale and was manufactur ed within the last 6 years.
(c) the alarm has been i ns t al led by an approved Mongoose installation agent
(d) it has been installed according to the AS/NZS 3749.2 Installation Standards and/or to our written instructions.
(d) provision of pro of of purchase stating where it was purchased and by whom it was installed.
(e) if the alarm is installed by anyone other than an approved Mongoose installer a 12 month par t s only warranty appli es
(f) an authorised inst allation centre has determined that the defect complained of is a genuine product defect and not caused by;
(I) incorrect installation or any other consequential dam age c aused by the vehi c le or ot her vehicle parts
(ii) operation of alarm after it is know n t o be defective
(iii) alteration or modification of the alarm or its components
(iv) the fitment of additional sec ur ity parts or accessor ies not supplied by or a pproved of by Mongoos e
(vi) any work car r ied out on the alarm by some one other than an author ised Mongoose installation centre
(vii) misuse, ac c ident, deliberate ac t or abuse (eg: misdirect ed electrical curr ent, ingress of water or fluid, vehicle damage)
Exclusions;
(I) removal & refitting cos ts of parts (ii) mobile service costs
(iii) batteries, i.e. r em ote controls (iv) normal wear and tear
(v) alarms operated out s ide the original country of purchase (vi) freight costs of parts to rectification cent r es
(vii) transport c os ts of getting a vehicle to a r epair c entre
(viii) consequential costs of vehicle non-operation where the remote controls or PIN code card are lost, not available, or an ina bility to use
INSTALLATION WARRANTY
Warranty for the instal lation is borne by the ori ginal installing agent only.
The period and terms of war ranty are deter min ed by the installation agent and should be ver ified with them.
Rectification work required to correct an ins tallation fault carr ied out by anyone oth er than the original inst al lation agent will inc ur their charges.
Authorisation to have this work carried out and agreement to have any costs refunded should be obtained from the original instal l at i on agent prior
to work commencing.
Whilst every care is taken in fitting the sec ur ity system, Mongoos e ac c ept s no responsibility for any damage caused to a vehicle in the install at ion
process. Respons ibility is borne by the installer.
THIS WARRANTY IS ONLY TRANSFERABLE AS PRESCRIBED AS BELOW
a) If the vehicle is s old with this product, the new owner receives the balance of the warrant y but up to a period of 3 years.
b) If the original owner has the system re -ins talled into an alternative vehicle by an aut horise Mongoose inst allation centre, the owner
receives the remai ning period of warranty. If r e-ins talled by an unauth or ised person, this w ar r anty ceases.
The Mongoose M80 models are manufactured, tested and certified to
the Australian and New Zealand Standards for vehicle security systems.
Manufactured for: Mongoose (Australia) Pty Ltd
Make & Model Number: Mongoose M80 Series
Country of manufacture: Taiwan R.O.C.
Supply voltage: 12v DC nominal – negative ground
Current consumption: 14~22mAmp (depending on alarm accessories)
Suitability: All vehicles with 12v negative earth batteries
Date of manufacture: Refer date code on alarm module case
AS/NZS3749.1 2003 Class A & B definition: includes control equipment including setting and
unsetting facilities, all sensors, warning devices and provision for immobilisation of the vehicle.
Whilst this security system provides a deterrent, it may not prevent theft or damage through
wilful criminal inte nt .
Mongoose do es not by infer ence, i ntent or any ot her means guara ntee that a vehi cle fi tted with
one of it’s security systems will not be stolen, broken into, tampered with, or parts taken.
Mongoose does not offer nor will pay compensation for any loss. We recommend adequate
vehicle insurance and the fitment of other security devices as deemed necessary.
The loss and any associated costs of replacing the remote controls and/or PIN code card in
making the vehicle mobile (or towage) are the responsibility of the vehicle owner/driver.
PROOF OF PURCHASE
PLEASE RETAIN
OWNERS NAME:…………………………………….. VEHICLE MAKE:…………………………..
ADDRESS:…………………………………………….. VEHICLE MODEL:…………………………
……….………………………………………. VEHICLE REG’ NO:……………………….
TELEPHONE NO:…………………………………….. ALARM MODEL NO:……………………….
ALARM PURCHASED F ROM:……………..
Dealer
DATE PURCHASED:.……………………….
INSTALLED BY:..……………………………
DATE INSTALLED:………………………….
INSTALLER SIGNATURE:…………………
OWNERS SIGNATURE:……………………
Please complete the above details , detach from this manual and keep in a safe place. These details
should be presented to your Mongoose dealer in the unl ikely event that you require this product to be
repaired under the term s of the ‘product warranty’. Ref er ‘Warranty Condit ions’. Fail ure to provide thi s
‘Proof of Purchase’ m ay result in rectification charges being made. If you sell the vehicle within the
warranty term, please pass on thi s on to the new owner.
www.mongoose.com.au
www.mongoose.co.nz
Loading...