Mongoose M40 Operating Instructions Manual

M40
Vehicle Security System
OPERATING
INSTRUCTIONS
AS/NZS4601 amendment 1 2003
& AS/NZS3749.1 2003 Class B
(when optional siren fitted)
REMOTE CONTROL KEY
2 supplied
BUTTON ONE ONLY
‘ARM’ (& LOCK)
PRESS FOR 1.5 SECONDS
TO ARM THE SECURITY SYSTEM
(DOORS WILL ALSO LOCK IF THE
CENTRAL LOCKING HAS BEEN
CONNECTED)
WHEN SIREN ADDED
SIREN WILL CHIRP ONCE TO
CONFIRM ARMING
PRESS FOR 3 SECONDS TO
BUTTON TWO ONLY
‘DISARM’ (& UNLOCK)
PRESS BUTTON TWO TO
DISARM THE ALARM SYSTEM.
(DOORS WILL ALSO UNLOCK
IF THE CENTRAL LOCKING
HAS BEEN CONNECTED)
WHEN SIREN ADDE
D
SIREN WILL CHIRP TWICE TO
CONFIRM DISARMING
BUTTON ONE
& TWO TOGETHER
SILENT ARM & AUTO SILENT DISARM
PRESS
BOTH BUTTONS TO SILENTLY ARM WITH NO CHIRPS. DISARMING IS
AUTOMATICALLY SILENT. ONLY APPLICABLE WHEN A SIREN IS ADDED.
The remote control is waterproof and also allows a modified ignition ke
y to be inserted into
the remote so it is all one piece
see last page of this manual
.
ARMING THE SYSTEM
-
BY REMOTE
The system is armed by depressing the remote control
momentarily (approx. 1~1.5 seconds).
You will notice the
vehicle
lights will flash once to indicate that the system is armed.
(The optional siren
, if fitted,
will chirp once)
The dash board warning light, LED, will slow flash to indicate armed mode. If
your vehicle has central
locking and it has been
connected to this security system, the doors will lock at the same
time as
arming.
The system will be fully armed after approximately 5 seconds.
DISARMING THE SYSTEM
-
BY REMOTE
Press the remote control to
disarm the system.
The
vehicle
lights will flash twice and the doors will unlock if wired
to the vehicle’s central locking
system. (The optional siren will chirp twice)
The dashboard LED will begin to fast flash to
indicate the system will automatically
re-arm after 30
seconds.
You must start the engine to prevent the system re
-
immobilising.
AUTOMATIC DUAL CIRCUIT ENGINE IMMOBILISATION
30 SECONDS AFTER IGNITION OFF
If the system is not manually armed by the remote control the vehicle will be automati
cally
immobilised
30 seconds after the ignition is turned off
. The dash board LED will fast flash for 30
seconds to indicate the system is in this sequence. After 30 seconds the dash board LED will slow
flash to indicate armed mode and the parking lights
will flash once. (The optional siren will chirp once)
NOTE:
As this security system is designed and certified
Standards requirements, the automatic
immobiliser cannot be programmed off.
SECURITY RE
-
ARM (& RE
-
LOCK)
The system will automatically re
-
immobil
ise after 30 seconds if it has been disarmed by remote.
Doors will also re
-
lock, if connected, if no door is opened within the 30 seconds. Opening a door will
not prevent the engine from being automatically immobilised
the engine must be started to preve
nt
this. For the security re
-
lock feature to operate, the system must have been initially set by the remote
control.
TRIGGER & 2 STAGE DISARM
When armed, if a door is opened or the ignition is switched on the
vehicle
lights will flash for 30
seconds (the
optional siren
, if fitted,
will sound).
If the system is being triggered, press the disarm button once to cancel the
trigger
.
Press a second time to disarm the system.
AUTOMATIC RE
-
SET
After the system has been triggered, it will automatically re
-
set t
o the armed position. If the
vehicle
lights flash 4 times upon disarming, this indicates the system has been triggered.
ARM CONDITION MEMORY
Should the vehicle battery be disconnected, the system memorises the last set position of the system.
If the syste
m was disarmed and the engine not immobilised prior to battery disconnection,
reconnection does not immobilise the vehicle until reset by the ignition being turned ON then OFF.
If the battery was disconnected whilst the system was armed, reconnection will
return the system to
the armed state and then immediately trigger.
PARK LIGHTS FLASHING
(connection to the indicators may infringe your warranty)
The park lights flash to confirm the arming and disarming of the system. They will also flash if the
system i
s triggered whilst the system is armed. The park light output is fuse protected to prevent the
module being shorted.
PARK LIGHT CONFIRMATION / CODES
This is a visual indication of system status.
1 Flash
-
Armed by remote.
2 Flashes
-
Disarmed.
3 Fl
ashes
-
Armed by remote with a door left open.
4 Flashes
-
Disarmed but system was triggered.
Flashes for 30 seconds
-
System triggered.
DASH MOUNTED WARNING LIGHT
-
LIGHT EMITTING DIODE (LED)
Located on or near the dashboard area, the status LED i
s a small
blue
flashing light that indicates the
vehicle is fitted with a security system. This LED needs to be visible
from outside the vehicle as a
theft deterrent
.
A) Slow flashing
-
system armed.
B) LED off
-
system disarmed.
C)
Fast flashin
g-30 second immobilisation or auto re
-
arm countdown.
EMERGENCY OVERRIDE
4 DIGIT PIN CODED
The system can be disarmed by entering your the unique 4 digit PIN
code shown on the ‘PIN Code Card’ issued with this product.
KEEP THE CARD IN A SAFE P
LACE
NOT IN THE VEHICLE !
Following is an example using PIN code
4525
Unlock
,
enter the
vehicle
and close all doors, then
the code
isinput
by turning the ignition ON or OFF in sequence with the
alarms
dash mounted
LED.
1.
Ignition ON
-
LED will light permanently to commence override.
2.
Ignition OFF
-
LED
will start flashing. Count the number of flashes for the first number.
3.
Ignition ON
-
after4flashes (1
st
number of the example)
. The LED will light.
4.
Ignition OFF
-
count the number of flashes
.5.Ignition ON
-
after
5
flashes (2
nd
number).The LED wi
ll light.
6.
Ignition OFF
-
count the number of flashes
.
7.
Ignition ON
-
after2flashes
(3rdnumber). The LED will light.
8.
Ignition OFF
-
count the number of flashes
.9.I
gnition ON
-
after5flashes (4
th
number).
10.
The system will now disar m and the veh
icle can be started
.
Note: If your PIN code contains a “0”, this equals ‘10’.
Should you miss the LED flashes or enter a digit incorrectly, wait for 11 flashes and simply repeat the procedure
from step 1).
This override sequence will have to be used to start the engine if your remote controls are not
available or inoperative.
MONGOOSE
EMERGENCY
4 DIGIT PIN CODE OVERRIDE
PLEASE KEE P THIS CARD I N A SAFE PLACE
BUT BE READILY AVAIL ABLE SHOULD YO U
NEED TO USE THE OVE RRIDE P RO
CEDURE
DO NOT LOSE THIS CARD
PIN CODE:
INSTALLATION
For full Standards compli
ance, this product must be carried out by authorised installers to
comply with the AS/NZS 3749.2
-
1997 Standard or any updated versions.
The main module has concealed plugs with only black wires emitting from it. Th
e w
ires are labeled for
the function;
1
LIGHT
-
(+) 12V OUTPUT TO PARKING LIGHTS
2
DOOR TRIGGER (‘+’ OR ‘
-
‘ SELECTABLE BY JUMPER J5. FACTORY SET TO ‘
-‘)3(-
) NEGATIVE GROUND x 2
4
(+) 12V FUSED CONSTANT POWER
5
(+) 12V IGNITION INPUT WIRE (ALSO +12V BACK
-
UP FOR IMMOB
ILISATION)
6(-
) GROUND WHEN ARMED
7(-
) LOCK, LOW CURRENT (0.3 SEC PULSE
OPEN JUMPER J5 FOR 4.0 SEC)
8(-
) UNLOCK, LOW CURRENT (0.3 SEC PULSE
OPEN JUMPER J5 FOR 4.0 SEC)
9
(+) OPTIONAL SIREN OUTPUT
10
IMMOBILISER CIRCUIT NO’ 1 (BLACK TAPED TOGETHER)
11
IMMOBILISER CIRCUIT NO’ 2 (BLACK TAPED TOGETHER)
12
DUMMY IMMOBILISER CIRCUIT NO’ 3 (CLEAR TAPED TOGETHER)
13
LED
REMOTE ‘CODE LEARNING’
The main alarm module has
a learning capacity to memorise up to four remote controls.
If you wish to add further remotes, or a remote has to be replaced, the new remote needs to be
memorised into the main module. If for instance you have lost a remote and are fearful that s
omeone
may try to use it, the lost remote can be deleted from memory so it cannot be used.
To learn a remote or add an additional remote:
Disarm the system
Open the drivers door and leave open
Turn the ignition ON/OFF 3 times within 5 seconds (ignition re
mains off)
The park lights will flash 3 times (and if fitted, the siren will chirp 3 times) and the dashboard
LED will light permanently to confirm you have entered remote code learning mode.
Press button one on the first remote
lights will flash once (o
ptional siren chirps once) as
confirmation of reception
Press button one on the second remote
lights will flash twice (optional siren chirps twice) as
confirmation of reception
Repeat for up to four remotes
(lights flash three times for the 3
rd
remote an
d four times for the 4th)
Leave the system for 10 seconds or turn ignition ON to complete the process. This is confirmed
by 3 fast light flashes (and 3 chirps if siren connected) and LED off.
NOTE: When learning a new replacement or additional remote, the
original remote(s) must
be re
-
learnt or they will be erased from memory and will not operate this system.
To delete a lost remote from memory:
Enter learning mode as detailed above. Memorise existing remote once. The lost remote is now
deleted. When a rep
lacement is obtained, learn both the existing and new remotes into memory as
detailed above.
WARRANTY CONDITIONS
PRODUCT WARRANTY
Mongoose warrants for a period of 36 months that it will make good without charge at Mongoose’s discretion, by repair or repl
acement with a reasonable
equivalent, any defect in the product providing that;
(a) the defect has been notified as soon as it is noticed to an authorised Mongoose installation c entre, distributor or agent (in the first instance to
the original inst
allation centre).
(b) the alarm is less than 3 years of age from the date of sale and was manufactured within the last 4 years.
(c) the alarm has been installed by an approved Mongoose installation agent
(d) it has been installed according to the AS/NZS 37
49.2 Installation Standards and/or to our written instructions.
(d) provis ion of proof of purchase stating where it was purchased and by whom it was installed.
(e)
if the alarm is installed by anyone other than an approved Mongoose installer a 12 month
par
ts only
warranty applies
(f) an authoris ed installation centre has determined that the defect complained of is a genuine product defect and not caused by;
(I) incorrect installation or any other consequential damage caused by the vehicle or other vehi
cle parts
(ii) operation of alarm after it is known to be defective
(iii)
alteration or modific ation ofthe alarm or its components
(iv)
the fitment of additional security parts or accessories not supplied by or approved of by Mongoos e
(vi) any work carried o
ut on the alarm by someone other than an authorised Mongoose installation centre
(vii) misuse, acc ident, deliberate act or abuse (eg: misdirected electrical current, ingress of water or fluid, vehicle damage)
Exclusions
;
(I) removal & refitting costs
of parts and/or accessories
(ii) mobile service costs
(iii) batteries, i.e. remote controls
(iv) normal wear and tear
(v) alarms operated outs ide the original country of purchase
(vi) freight costs of parts to rectification centres
(vii)
transport costs of getting a vehicle to a repair centre
(viii) c onsequential cos ts of vehicle non
-
operation where the remote controls or PIN codecard are lost, not available, or an inability to use
INSTALLATION WARRANTY
Warranty for the installation i
s borne by the original installing agent only.
The period and terms of warranty are determined by the installation agent and should be verified with them.
Rectification work required to correct an installation fault carried out by anyone other than the or
iginal installation agent will incur their charges.
Authorisation to have this work carried out and agreement to have any costs refunded should be obtained from the original installation agent prior to
work commencing.
Whilst every care is taken in fitting
the sec urity system, Mongoose accepts no responsibility for any damage caused to a vehicle in the installation
process. Responsibility is borne by the installer.
THIS W ARRANTY IS ONLY TRANSFERABLE AS PRESCRIBED AS BELOW
a)
If the vehicle is s old with this
product, the new owner receives the balance of any warranty period remaining.
b)
If the original owner has thes ystem re
-
installed into an alternative vehicle by an authorise Mongoose ins tallation centre, the owner receives
the remaining period of warranty.
If re-installed by an unauthoris ed person, this warranty ceases.
This product is manufactured, tested and certified to the joint
Australian and New Zealand Standards AS/NZS4601 1999 amendment 1 2003
& AS/NZS3749.1 2003 Class B when fitted with a compl
iant siren.
Manufactured for: Mongoose (Australia) Pty Ltd
Make : Mongoose
Model : M40
(MX40MKII)
Country of manufacture: Taiwan R.O.C.
Supply voltage: 12v DC nominal
negative ground
Current consumption: 0.3amps (excluding any optional access
ories)
Suitability: All vehicles with 12v negative earth batteries
Date of manufacture: Refer date code on module case
Whilst this security system provides a deterrent, it may not prevent theft or damage through wilful
crimi
nal intent. Mongoose does not by inference, intent or any other means guarantee that a vehicle
fitted with one of it’s security systems will not be stolen, broken into, tampered with, or parts taken.
Mongoose does not offer nor will pay compensation for an
y loss. We recommend adequate vehicle
insurance and the fitment of other security devices as deemed necessary.
The loss and any associated costs of replacing the remote controls and/or PIN code card in making
the vehicle mobile are the responsibility of th
e vehicle owner/driver.
PROOF OF PURCHASE
DO NOT LEAVE THIS INFORMATION IN THE VEHICLE
OWNERS NAME:………………………………………..
VEHICLE MAKE:………………………………..…..
ADDRESS:……………………………………………..
VEHICLE MODEL:………………………..………
……….……………………………………….
VEHICLE REG’ NO:…………………….
.……….
PIN CODE:…………………………………………
TELEPHONE NO:……………………………………..
ALARM MODEL NO:…..
M40
……
………….
….
ALARM PURCHASED FROM:…………….…….…..
Dealer stamp
DATE PURCHASED:.……………………………..….
INSTALLED BY:..…………………………….…..……
DATE INSTALLED:…
…………………………..…….
INSTALLER SIGNATURE:……………………………
OWNERS SIGNATURE:………………………………
Please complete the above details, detach from this manual and keep in a safe place. These details should be presented to your Mongoose
dealer in the unlikely event that yo
u require this product to be repaired under the terms of the ‘product warranty’. Refer ‘Warranty Conditions’.
Failure to provide this ‘Proof of Purchase’ may result in rectification charges being made. If you sell the vehicle within the warranty term, plea
se
pass on this on to the new owner.
A modifiedignition key can be insert6edinto the remotecontrol as shown in the photographs below.
A removable blanking plate in the remote is the template for cutting the ignition key.
Mongoose (Australia) Pty Limited
Sydney, Brisbane
Mongoose (New Zealand) Limited
Auckland
For service
, please contact the
Mongoose
dealer who installed this product
;
Loading...