Model number: M33
CAR ALARM SYSTEM
Owner’s Operation Manual
Please read and try out all the features
For correct operation and warranty compliance,
we recommend professional installation of this
product by your authorised Mongoose dealer.
Suitable for 12volt, negative ground vehicles
Amended June 2015
BUTTON 2 ONLY
‘DISARM’ (& UNLOCK)
PRESS BUTTON TWO TO
DISARM THE ALARM SYSTEM.
(DOORS WILL ALSO UNLOCK
IF THE CENTRAL LOCKING
HAS BEEN CONNECTED)
BUTTON 4
‘PANIC’
PRESS AND HOLD TO SOUND THE
SIREN AND FLASH THE LIGHTS.
PRESS AGAIN TO CANCEL.
BUTTON 1 & 2 TOGETHER
BOOT RELEASE (CH2)
AFTER DISARM, PRESS BOTH
BUTTONS TO OPEN THE BOOT (IF
THE VEHICLE IS EQUIPPED WITH
ELECTRIC RELEASE)
ALARM REMOTE CONTROL – 2 supplied
BUTTON 1
‘ARM’ (& LOCK)
PRESS FOR 1.5 SECONDS
TO ARM THE SECURITY SYSTEM -
(DOORS WILL ALSO LOCK IF THE
CENTRAL LOCKING HAS BEEN
CONNECTED)
SENSOR DISABLE
PRESS BUTTON 2 & 3 TOGETHER
WITHIN 5 SECONDS OF ARMING
TO BYPASS THE SHOCK SENSOR
BUTTON 3
SILENT ARMING
PRESS TO ARM THE ALARM WITH
NO SIREN CHIRPS.
(DISARM IS THEN
AUTOMATICALLY SILENT)
CONTENTS
Arming the system……………………. 4 Indicator flash confirmation codes….... 7
Silent arming…………………………… 4 Siren chirp sounds……..……..……..…. 7
Defective zone bypass.……………….. 4 LED flash codes………………………… 7
Disarming the system…………………. 4 EMERGENCY OVERRIDE………… … . 8
Security re-arm.................…………….. 4 Valet mode (security system disable)… 8
Engine immobiliser…………………….. 4 Automatic arming……………………….. 8
Auto re-set…………....................…….. 5 Automatic door locking…………………. 8
Central locking…………………………. 5 Ignition safety door locking………....….. 8
Remote controls……………………….. 5 2 stage unlock…………………………… 8
Doors, bonnet & boot…………………. 5 Code learning...................................….. 9
Impact sensor …………….............…… 5 Testing your alarm……………………. … 9
Shock sensor bypass…………………. 6 Programmable options………………….. 10
Panic……...................................…….. 6 Wiring diagram…………………………… 11
Battery back-up siren…………………. 6 Warranty terms and conditions…………. 12
Arm condition memory..........…...……. 6 Proof of purchase………………………… 13
Dome light supervision option……….. 6
OPERATING YOUR VEHICLE SECURITY SYSTEM
ARMING (& LOCKING*)
Arm the system (and lock the doors*) by pressing but t on 1 on the remote control.
The indicators will f l as h once and the siren chirps once to indicate that the system is fully armed.
The dash mounted LED will light for 10 seconds as the security system checks vehicle integrity and then slow
flashes to indicat e armed mode.
SILENT ARMING
(Can be permanently silenced through programming)
Press button 3 to si l ent l y arm t he system without the siren chi rps. Disarming will t hen be automatically silent.
DEFECTIVE ZONE BYPASS
If any door, the bonnet or boot is open before arm ing the alarm , the das hboard LED wil l s tay lit as a warning. If not
closed before or after armi ng, the siren will emit a warning after a 30 second delay. The open circuit will then be
bypassed. The alarm will arm an open circuit when it is clos ed.
DISARMING (& UNLOCKING*)
– (See 2 stage unlock option page 8)
To disarm (and unlock*), press remote control but t on 2. Siren will chirp twice and the indicators will flash twice.
The indicators will then s t ay lit f or 30 seconds to provide perim et er i l lumination.
If disarming during an alarm activation, press but ton 1 or 2 to cancel sounding, then butt on 2 t o di sarm.
SECURITY RE-ARM (& RE-LOCK)
- programmable
The alarm will autom atically re-arm if it has been disarmed by remote but t he doors have not been opened within
30 seconds. Doors also re-lock if central locking connected. LED fast flashes to signi f y countdown t o aut o re-arm.
ENGINE IMMOBIL I SER
This security system is equipped with an engine immobi l iser to prevent engine starting when the s ystem is armed.
4
AUTOMATIC RE-SET
If the alarm is triggered, the siren will sound for 60 seconds. Once it stops, the system resets to the armed
position. It will t hen re-t ri gger on the next intrusion. (Max’ 5 t ri ggers per circuit)
CENTRAL LOCKING –
(programmable for electric or vacuum locking)
This security system has bui l t-in relays to enable remote control of a v ehicles central locking systems.
Certain vehicles m ay require additional extra cost parts to enable the correct use of this feature.
CODE HOPPING REMOTE CONT RO L S
2 water resistant remot e c ontrols are supplied with the M33. Maximum 3 remotes can be used.
This coding system i s completely random therefore eliminating the possibili ty of recording it (code grabbing).
DOORS, BONNET AND BOOT PROTECTION
The siren will sound and the indicators will flash for 30 sec onds should any of these be opened when the system is
armed. The system is connected to the vehicles courtesy door light switches. These switches must function
correctly for the alarm system to operate. The fitting of door s wi t ches is not included with thi s product.
IMPACT SENSOR - 2 STAGE
The sensor is designed to det ect impacts to t he vehicle such as vi olent glass breakage. It may also be triggered
by shock waves produced from loud exhausts and heavy vehic le traffic. I t should not be triggered by normal wind
or rocking m ot ions . If the s ensor rec eiv es a l ight i m pact the s iren fas t c hirps for a few s econds as a pre-warning. It
sounds fully for 30 seconds if i t det ects a heavy impact.
The sensitivity level is adjustable by the installer. Ov er sensitivity can cause fal se alarms.
SHOCK SENSOR BYPASS
The shock sens or can be bypassed t o prevent fals e alarm s . A rm the s ystem and withi n 5 sec onds pres s UNLOCK
& MUTE at the same t i me to disable the sensor. It will be active next time the alarm is armed.
5
BOOT RELEASE BY REMOTE
If you vehicle is equipped with elec tric release of the boot, it can be connected to t his alarm system. This may
incur additional charges. Di s arm the alarm and then press but t ons 1 & 2 at the same time to open the boot.
PANIC
In the event of personal attack, the alarm can be ‘panicked’ by pressing the rear red remote control button for
more than 2 seconds.
Press any button to cancel the alarm.
ELECTRONIC BATTERY BACK-UP SIREN
This is mounted under the bonnet and must be sit uated in a place to protect i t from heat and water damage such
as driving through deep water or engine cleaning. The alarm system i s suppl ied with 2 s iren k eys. T hese are us ed
to turn off the sirens int ernal bat tery during vehicle servicing or vehicle battery replacement/disc onnection.
The keys do not deactivat e t he alarm system.
If washing the engine bay, cover the si ren wit h a plastic bag to prevent damage.
Heat or water damage is not cov ered by the warranty.
ARM CONDITION MEMORY
Should the vehicle batt ery be disconnected, the system memorises t he last set positi on of the alarm. If the alarm
was disarmed, reconnection does not cause the alarm to sound. If the battery was disconnected whilst armed,
reconnection will cause the system to trigger. To cancel, disarm with the remote control. (Vehicle battery
disconnection will c ause the opti onal battery back -up siren to s ound - this is t urned off at t he siren with the speci al
key provided)
DOME LIGHT SUPERVISION
- programmable
The system prov ides the fac ility for dome light s upervision. Upon disarm ing, the interior light will i lluminate for 30
seconds which is c anc el l ed upon igni t i on on.
NOTE: The fitting of t hi s option may make the ‘s ecurity re-arm (& re-lock)’ feature inoperative.
6
INDICATOR LIGHT FLASH CONFIRMATION / CODES
This is a visual indi cation of system status.
A) 1 Flash - Armed
B) 2 Flash - Disarmed
C) On for 30 sec’ - Indicates system i s di sarmed and provides perimet er il l umination
SIREN CHIRP CODES
This is an audible indicat ion of system status.
A) 1 Chirp - Armed
B) 2 Chirps - Disarmed
C) 3 Chirps – A warning that a door, the bonnet or boot is open 30 seconds after arming
D) 3 Chirps – When disarming, a warning that t he al arm has been triggered
E) Fast chirps - Light impact detected by the shock sensor
DASH MOUNTED WARNING LIGHT - LED
Located on or near the dashboard area, the LED is a s mall flashing light t hat i ndi cates the vehicle is fitted with a
security system. The LED also tells the status of t he al arm;
A) S l ow f l as hi ng - System armed
B) Fast flashing - Countdown for automati c arming functions
B) LED off - System is off
C) Continuously lit - Valet mode or remote code learning
D) 1 flash, 1 pause - Bonnet triggered
E) 2 f l as h, 1 pause - Boot triggered
F) 3 flash, 1 pause - Door triggered
G) 4 flash, 1 pause - Igniti on t ri ggered
H) 5 flash, 1 pause - Sensor triggered
7
EMERGENCY OVERRIDE
At the time of installation a hidden push button switch was fitted, usuall y under the das hboard.
If the alarm is arm ed and fails to respond to the remote control, or you have misplac ed it, you can override the
alarm as follows;
1) Open the door with the ignition k ey - the al arm will trigger
2) Turn on the ignition and pres s the ov erride button for 3 s econds - this will canc el the alarm and put t he alarm in
valet mode – LED on constant. See below to cancel v alet mode.
VALET MODE - LED PERMANENTLY LIT
When di sarmed, turn the ignition on and press and hold the ov erride switch for 3 seconds. Siren will chirp and
lights flash once to confirm. LED will stay lit to indicate valet mode. Repeat to turn the system bac k on.
AUTOMATIC - LAST DOOR ARMING (Programmable)
The system can be programm ed to arm automaticall y 30 seconds after closing the last door (or bonnet or boot).
The LED will fast flas h during t he auto arming countdown.
IGNITION SAFETY DOOR LOCK
(Programmable)
If the central locking is c onnect ed to t his s ec urity system , the doors will automatically lock after 1 second when the
engine is started (or ignition is turned on). The doors will unlock when the ignition is turned off .
If a door is left open during engine starting, the doors will not lock but cause the indicators to flash 4 times to
indicate an open door.
2 STAGE UNLOCK
– optional connection
This alarm has the abil ity to allow you to only unlock the drivers ’ door when you disarm and then a 2
nd
press of the
disarm button on the rem ot e unl ocks the passenger doors.
This feature requires the ins taller of this product to wire your vehic le differently, so this feature must be specified
prior to installation.
8
REMOTE CONTROL CODE LE ARNING
• If you need to replace a remote control, it must be memorised to t he al arm system before it can be us ed.
• A power surge or interruption to the power supply may cause loss of memory.
• If your alarm fails to respond to the remot e t ry re-learning them.
TO MEMORISE A NEW REMOTE:
a) Disarm the system by remot e or t he override method described on the previ ous page.
b) Turn the ignition off/on 3 times leaving on third time. Siren will chirp.
c) Press the override switch for 5 seconds - si ren chirps 3 times to confirm learning mode.
d) Press button 1 twice on 1
st
remote. Siren will chirp to confirm.
e) Press button 1 twice on 2
nd
remote. Siren will chirp t o confirm.
Repeat this procedure if you have a third remote. Turn ignition off to complete the learning sequence.
Note: If you lose a remote, re-learning t he existing remote will eras e the one that is lost.
TESTING YOUR ALARM
We strongly recommend that you test your alarm f requently. It takes only a short time and is very important to
maximis e t he prot ection of your vehicle.
1. Arm the system . Unlock the door with the igni t i on key and open the door. The alarm should activate. Check all
the other doors , bonnet and boot by the same procedure.
2. Engine immobil i ser. Open the drivers window. Arm the alarm. Without opening a door, reac h i n and t ry to st art
the engine. It should not st art.
3. Shock sens or. Check the shock sensor by giving the vehicle varying degrees of i mpact.
4. Remote controls. Do not get them wet, drop them on a hard surface or tamper with the i nternals. To ensure
correct operation at all times, replace the battery every 12 months or sooner if you notice operating range is
reducing.
9
PROGRAMMABLE FEATURES
• Turn ignition on
• Press override butt on 5 t i mes – siren chirps to confirm program mode
• Press override the number of times in the c hart bel ow
• Press the rem ot e but ton to change a feature
Sequence
Feature
Button 1
Button 2
1
Last door auto arming
Off *
On 2 Ignition door lock
On
Off *
3
Auto re-arm after rem ot e di s arm
Off *
On 4 Unlock output (wire #14)
Single pulse *
Double pulse
5
Siren chirps
On *
Off 6 Perimeter night light
On
Off *
7
CDL pulse length
1 second *
3 seconds
8
Arm when ACC on #
Off *
On
*Default setting # This feature allows for add-on turbo timers
Jumper on side of modul e – 2 stage unlock – see page 8
Open = Drivers door unlock s on 1
st
press – press again to unloc k passenger doors
Closed = All doors unlock at the same time
Amendment to M33 Owner’ s operator manual – June 2015
10
WIRING DIAGRAM Installation to be carried out by suitably qualified persons.
Top Row
1 Red (+) Constant 12v pow er
2 Orange/white (+) Li ght flash output x 2
3 Blue/white (+) 2
nd
unlock output
4 No connection
4 Grey (-) Ground when armed
6 No connection
7 Orange Unlock N/C
8 Blue Unlock common
9 Brown Unlock N/O
10 Purple Lock N/C
11 Green Lock com m on
Bottom Row
12 Brow n/white (+) Siren output
13 Black (-) Ground
14 No connection
15 Red/white (-) Boot trigger input
16 Black/ w hit e (+) Dome light output
17 Green/red (+) Door trigger input
18 Yellow (+) Igni tion input
19 Blue/white (-) Bonnet trigger input
20 Pink (-) Boot release
21 Green/w hite (-) Door trigger input
22 White Lock N/O
ANTENNA – DO NOT CUT – SHORTEN - CURL
2ndSENSOR P ORT FOR
OPTIONAL SENSORS
PLUG-IN SHOCK SENSOR
L.E.D.
OVERRIDE SWITCH
JUMPER FOR 2 STA GE UNLOCK
Red +12v
Black (-)
Bl ue T rig ger (-)
Wh ite Pre -i ntrus ion (-)
1 12
2 13
3 14
4 15
5 16
6 17
7 18
8 19
9 20
10 21
11 22
Red +12v
Black (-)
Bl ue T rig ger (-)
Wh ite Pre -i ntrus ion (-)
ENGINE IMMOBILISER RELAY
GREY WIRE
OF M33
87
85
86
30
87a
+12V
IGN/ACC
INTERUP TED
CIRCUIT
IGN’ SWIT CH
CUT
CHOOSE STA RTER –IGNITION –FUEL PUMP
Si ren Wi re s
Red - +12v constant
Black – Ground
Bl ue – (-) trigger
White – (+) trigg er
WARRANTY CONDITIONS
Mongoose warrants that it will make good without charge, by repair or replacement with a reasonable equiv alent, at Mongoose’s discretion,
any defect in the product, excluding def ec t in installation, submitted for claim for a period of ONE year from date of sale provided t hat;
(a) the defect has been notified t o an aut hor is ed Mongoose ins t al lation centre, distributor or agent ( in t he first instance to the original ins t al lation
centre).
(b) the alarm is less 12 months old from the date of s ale and was manufac t ur ed wi t hi n t he las t 2 years.
(c) the alarm has been installed according to our wr itten instructions
(d) provision of proof of pur c has e and war r anty registration on request.
(e) an authorised installation centr e has det er mined t hat the defect complained of is one of workmanship and not c aus ed by;
(I) misuse or abuse such as misdirected current, water or fluid damage
(ii) operation of alarm after it is known to be defective
(iii) accident or deliberate act
(iv) alteration or modificat ion of the alarm, or its components, by any party not authorised by Mongoose
(v) the fitting of par ts or accessories not supplied or approved of by Mongoose
(vi) any work carried out on t he alar m by someone other than an aut hor i s ed Mongoose installation centre
(vii) any consequential damage
(viii) if the alarm is installed by anyone other than an approved installer a limited parts only 6 month warranty may apply
Warrant y for the installation is borne by the original installing agent only. This will be chargeable if not returned to the original installer.
Whilst every care is taken by our installers in f itting the alarm, Mongoose takes no responsibility for any damage caused to a vehicle in the installation process.
Responsibility is borne by the installer and any claims directed to them.
Exclusions from this warranty are;
(I) alarms operated outside the original country of purchase (v) faults associated with the installation
(ii) batteries, i.e.; as fitted to the remote controls (vi) mobile service costs for repairs
(iii) normal wear and tear (vii) labour cos ts for repairs
(iv) transportat ion of r epair s or r eplac ement par ts etc. to rectification centres
THIS WARRANTY IS NOT TRANSFERABLE
DISCLAIMER:
Vehicle security systems are theft det er r ents only.
Mongoose does not by inference, intent or any other means guarantee that a vehicle fitted with one of our security systems will not be stolen, broken into,
tampered with, or parts tak en.
We recommend fully comprehensive vehicle insurance and home and contents insurance and to fit other security devic es s uc h as additional alarm sensors and
locking wheel nuts if the vehicle has expensive wheels and tyres.
12
PROOF OF PURCHAS E
PLEASE RETAIN FOR YOUR RECORDS
OWNERS NAME:………………………………….. VEHICLE MAKE:…………………..…………..
ADDRESS:…………………………………………….. VEHICLE MODEL:……………………….………
……….……….……………………………... VEHICLE REG’ NO:………………………………
TELEPHONE NO:…………………………………….. ALARM MODEL NO:…M33….………………….
ALARM PURCHASED FROM:…………………..…..
Dealer
DATE PURCHASED:.………………………….…….
INSTALLED BY:..………………………………..……
DATE INSTALLED:………………………….……….
INSTALLER SIGNATURE:…………………..………
OWNERS SI GNATURE:……………………….. ……
Please complete the abov e detail s, detach from this manual and keep in a saf e place. T hese details should be presented
to your Mongoose dealer in the unlikel y event that you require this pr oduct to be repaired under the terms of the ‘product
warranty’. Refer ‘ W arr anty Conditions’ . Failur e to prov ide this ‘ Proof of Purchase’ may result in recti fic ation charges being
made. If you sell the vehicle within the warranty term, please pass this on to the new owner.
Manufactured for: Mongoose (Australia) Pty Ltd
Make & Model Number: Mongoose M33 Series
Country of manufacture: China
Supply voltage: 12v DC nominal – negative ground
Current consumption: 0.3amps
Suitability: All vehicles with 12v negative earth batteries
Date of manufacture: Refer date code on alarm module case
Mongoose (Australia) Pty Limited
Sydney, Brisbane
www.mongoose.com.au
Mongoose (New Zeala nd) Lim ited
Auckland
www.mongoose.co.nz
Loading...