MONGOOSE M25
PROXIMITY TRANSPONDER AUTOMATIC TRIPLE IMMOBILISER
AS/NZS STANDARDS CERTIFIED
FEATURES:
• STANDARDS CERTIFIED TO AS/NZS4601 AMENDMENT 1 2003
• 3 STAR
• PROXIMITY TRANSPONDER
• AUTOMATIC TRIPLE CIRCUIT ENGINE IMMOBILISER
• DASHBOARD MOUNTED LED STATUS INDICATOR
• USER PROGRAMMABLE TRANSPONDER TAGS WITH MORE THAN 16
MILLION CODES
• UP TO 4 TAGS CAN BE PROGRAMMED
• AUTOMATIC ARMING AFTER IGNITION OFF
• AUTOMATIC RE-ARM IF ENGINE NOT STARTED
• 4 DIGIT PIN CODED OVERRIDE
• AUDIBLE BEEPER TO CONFIRM ARM AND DISARM
OPERATION
ARMING:
The engine automatically immobilises 30 seconds after the ignition has been
turned off. This feature cannot be turned off as it is a mandatory Standards
feature.
When the ignition is turned OFF, the dashboard LED will start to fast flash for
30 seconds to indicate the automatic sequence has commenced. It then slow
flashes to confirm the vehicle is immobilised together with 1 beep.
DISARMING:
Within 20 seconds of opening the door or turning the ignition on, present the
‘tag’ in close proximity to the area where the loop antenna is positioned. This
loop antenna is usually placed around the ignition barrel behind the plastic
coverings. The LED fast flashes to confirm disarming together with 2 beeps.
AUTO RE-ARM:
If the engine is not started within 20 seconds of disarming, the M25 will reimmobilise.
ARM CONDITION MEMORY:
If the car battery is disconnected, the security system will return to the same
state, armed or disarmed upon power re-connection.
EMERGENCY OVERRIDE – 4DIGIT PIN CODED:
The system can be disarmed by your unique 4 digit PIN code shown on the ‘PIN
Code Card’ issued with this product.
KEEP THE CARD IN A SAFE PLACE – NOT IN THE VEHICLE !
TIP: Record your PIN code in your cellphone for easy recall.
Following is an example using PIN code 4525
The code is entered by turning the ignition ON or OFF in sequence with the dash
mounted LED. The sequence is printed on the rear of the PIN code card.
Turn ignition ON - LED will light permanently to commence override.
Turn ignition OFF - LED will start flashing. Count the number of flashes for the
1st number (4 in the example).
Turn ignition ON - when the LED lights the 4th time. The LED will light solid.
Turn ignition OFF - LED will start flashing again. Count the number of flashes
for 2nd number (5 in the example).
Turn ignition ON - when the LED lights the 5th time. The LED will light solid.
Continue this sequence for all numbers. The M25 disarms and the vehicle
can be started.
Note: If your PIN code contains a “0”, this equals ‘10’.
If you input an incorrect number, wait for the LED to flash 11 times before trying
again.
This product is ma nufactured, tested and certified to AS/NZS4601 amendmen t 1 2003
for Mongoose (A ustralia) Pty Ltd
www.mongoose.com.au www.mongoose.co.nz
Make & Mode l Number: Mongoo se M25.
Country of manufacture: Taiwan R.O.C.
Supply voltage: 12v DC nominal – negative ground.
Current consu mption: 0.3amp s
Suitability: All vehicles with 12 v negative ear th batteries
Date of manuf acture: Refer date code on alarm mod ule case
Whilst this security sy stem provide s a deterre nt, it may not prevent thef t or damage through wilful
criminal intent. Mongoose doe s not by inf erence, intent or any o ther means guarantee that a
vehicle fitted with one of i t’s security systems will not be stolen, broken in to, tampere d with, or
parts taken.
Mongoose does not offer nor will pay c ompensation for any loss. We recommend adequate
vehicle insuranc e and the fi tment of oth er security de vices as deemed necessary. Any loss or any
associated co sts in making the vehicle mobile due to lo ss of the transponder tags or PI N code
card are the responsibility of the vehicle o wner/driver. See warranty co nditions.
This product must be installed according to the
requirements of the AS/NZS 3749.2 Installation Standard.
Remove all wire identifiers during installation.
Remove all wire identifier labels during installation.
IMMOBILISER (TRIPLE CIRCUIT) - IMPORTANT
A current draw test must be made on the chosen circuits for immobilisation.
The maximum continuous rating of this product is 10amps per circuit – do not
exceed this rating.
Check ignition circuit when ON and with all accessories turned on.
GROUND WIRES
Connect these to 2 separate ground points ensuring a good clean contact for
each. Do not connect together at one point.
IGNITION INPUT
Connect to the ignition wire of the vehicle which has +12v on both the ‘ignition on’
and ‘crank’ switch positions
DOOR INPUT WIRE
Connect to common (-) door wire. M25 senses door open to activate the loop
antenna and for programming.
LOOP ANTENNA
Remove steering column shrouds and fix antenna around the ignition barrel.
Alternatively, the loop antenna can be hidden anywhere in the vehicle – ensure the
vehicle owner knows the location.
LED
Mount where it is visible from outside and where the driver can see it
To test tag searching range
The range of the transponder tags can be tested;
• Disarm and close the door
• Turn the ignition on/off 6 times (ignition remains off). Beeper emits four beeps.
• Within 10 seconds offer the tag to the antenna.
LED will flash when the tag is detected.
• Turn the ignition on/off to reset back to normal mode.
PROGRAMMING TOUCH KEYS (maximum 4):
The system has a code learning capacity to learn up to 4 tags (2 supplied).
• Disarm the system with an existing tag or by using the PIN override
• Open the drivers door and leave open
• Turn the ignition ON/OFF 3 times
• The LED will flash 3 times (beeper will beep 3 times) to confirm learning mode
• Within 10 seconds present the 1st tag to the antenna – LED will flash once (beeper
will beep once)
• Repeat up to 4 tags – 2 beeps for 2nd tag, 3 beeps for 3rd tag, etc
• Leave system for 10 seconds to complete the learning procedure.
MONGOOSE M25 - INSTALLATION
Fix loop antenna around
ignition barrel behind
plastic covers
MONGOOSE M25
IMMOBILI SER CIRCUIT NO’ 1
IMMOBILI SER CIRCUIT NO’ 2
IMMOBILI SER CIRCUIT NO’ 3
(+) 12V INPUT CONSTA NT – FUSED
(-) GROUND NO’ 1
(-) GROUND NO’ 2
(+) IGNITION INPUT
(-) DOOR INPUT
Loading...