Mitsubishi Electronics XD2000, XD1000 User Manual
DLP™ PROJECTOR
MODEL
XD2000U
XD1000U
User Manual
ENGLISH
XD2000
XD1000
This User Manual is important to you.
Please read it before using your projector.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning fl ash with arrowhead symbol within an equilateral triangle is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of suffi cient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specifi ed power supply cord. If
you use another power-supply cord, it may cause
interference with radio and television reception.
Use the attached RGB cable and RS-232C cable with
this equipment so as to keep interference within the
limit of a FCC Class B device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN
THE PROJECTOR IS IN THE POWER ON MODE.
CAUTION
Not for use in a computer room as defi ned in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
When using the projector in Europe:
COMPLIANCE NOTICE
This Projector complies with the requirements of the
EC Directive 89/336/EEC “EMC Directive” as amended
by Directive 92/31/EEC and 93/68/EEC, and 73/23/
EEC “Low Voltage Directive” as amended by Directive
93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside of
the buildings. All places of operation are characterised
by their connection to the public low voltage power
supply system.
WARNING
Use the attached RGB cable and RS-232C cable with
this equipment so as to keep interference within the
limits of an EN55022 Class B device.
Please follow WARNING instructions.
EN-2
Contents
Important safeguards ........................................................................................................................4
Preparing your projector ....................................................................................................................6
Using the remote control ...................................................................................................................9
Setting up your projector .................................................................................................................10
Viewing computer images ...............................................................................................................13
Viewing video images ......................................................................................................................17
Menu operation ...............................................................................................................................22
Adjusting projected images .............................................................................................................25
Advanced features ..........................................................................................................................28
Replacing the lamp .........................................................................................................................32
Troubleshooting ...............................................................................................................................34
Indicators .........................................................................................................................................37
Specifi cations ..................................................................................................................................38
ENGLISH
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10
Information for users and Annex IV.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components
which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from
your household waste.
Please, dispose of this equipment at your local community waste collection/recycling centre.
In the European Union there are separate collection systems for used electrical and electronic product.
Please, help us to conserve the environment we live in!
Declaration of Conformity
Model number : XD2000U/XD1000U
Trade name : MITSUBISHI ELECTRIC
Responsible party : Mitsubishi Digital Electronics America, Inc.
9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Telephone number : +1-(949) 465-6000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Trademark, Registered trademark
• DLP™, Digital Micromirror Device, DMD and BrilliantColorTM are all trademarks of Texas Instruments.
• Microsoft or Windows are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
• PJLink is trademark applied for registration or registered trademark of Japan Business Machine and Information
System Industries Association in Japan, the United States and other countries.
• Other brand or product names are trademarks or registered trademarks of their respective holders.
EN-3
Important safeguards
Please read all these instructions regarding your
projector and retain them for future reference. Follow
all warnings and instructions marked on the projector.
1. Read instructions
All the safety and operating instructions should be
read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the operating
instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before
cleaning it. Do not use liquid aerosol cleaners. Use
a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as such
additions may result in the risk of fi re, electric
shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in contact
with water.
8. Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended
by the manufacturer or sold with the projector.
Any mounting of the appliance should follow
the manufacturer's instructions and should use
a mounting accessory recommended by the
manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and cart
combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do not
block these openings or allow them to be blocked
by placing the projector on a bed, sofa, rug, or
bookcase. Ensure that there is adequate ventilation
and that the manufacturer's instructions have been
adhered to.
10. Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11. Power-cord protection
Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them. Pay
particular attention to cords at plugs, convenience
receptacles, and points where they exit from the
appliance. Do not put the power cord under a
carpet.
12. Overloading
Do not overload wall outlets and extension cords
as this can result in a fi re or electric shock.
13. Objects and liquids
Never push objects of any kind through openings
of this projector as they may touch dangerous
voltage points or short-out parts that could result
in a fi re or electric shock. Never spill liquid of any
kind on the projector.
14. Servicing
Do not attempt to service this projector by yourself.
Refer all servicing to qualifi ed service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and refer
servicing to qualifi ed service personnel under the
following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen
into the projector.
(c) If the projector does not operate normally after
you follow the operating instructions. Adjust
only those controls that are covered by the
operating instructions. An improper adjustment
of other controls may result in damage and
may often require extensive work by a qualifi ed
technician to restore the projector to its normal
operation.
(d) If the projector has been exposed to rain or
water.
(e) If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change in
performance - this indicates a need for service.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specifi ed by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in fi re,
electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is in a
safe operating condition.
EN-4
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fi re or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifi cally explained in the User Manual do
not attempt to service this product by yourself. Please
contact your dealer when you want to fi x, adjust or
inspect the projector.
Do not modify this equipment.
It can lead to fi re or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged, unplug the projector and contact your dealer
for inspection. It may lead to fi re if you keep using the
damaged projector.
Do not face the projector lens to the sun.
It can lead to fi re.
Use correct voltage.
If you use incorrect voltage, it can lead to fi re.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is
operating.
It may hurt your eyes. Never let children look into the
lens when it is on.
Do not touch the air outlet grille and
bottom plate, which become hot.
Do not touch them or put other equipment in front
of the air outlet grille. The air outlet grille and bottom
plate, when heated, may cause injury or damage to
other equipment. Also, do not set the projector on the
desk which is easily affected by heat.
Do not look into the air outlet grille when
projector is operating.
Heat, dust, etc. may blow out of it and hurt your eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fi re.
Place of installation
For safety’s sake, refrain from setting the projector
at any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specifi ed below.
• Operating temperature: between +41°F (+5°C) and
+104°F (+40°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the
projector so that the projector does not overheat.
• Do not attach the projector to a place that is
unstable or subjected to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic fi eld. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free surface;
otherwise it may fall, causing serious injury to a
child or adult, and serious damage to the product.
• Do not stand the projector; it may fall, causing
serious injury and damage to the projector.
• Slanting the projector more than ±10°(right and
left) or ±30°(front and rear) may cause trouble or
explosion of the lamp. When you use the projector
in a tilted position, however, secure it to prevent it
from slipping down.
• Do not place the projector near air-conditioning
unit or heater to avoid hot air to the exhaust and
ventilation hole of the projector.
ENGLISH
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifi cations not expressly approved by Mitsubishi could void the user's authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
EN-5
Preparing your projector
Checking accessories
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in
the package.
Cables
Mini D-SUB
15-pin
Mini D-SUB
15-pin
RGB cable for PC
(246C521-10)
Audio/Video cable
(246C381-10)
USB 4-pin
(type B)
USB 4
(type A)
USB cable
(246C509-10)
-pin
Power supply parts Remote control parts
D-SUB 9-pin
D-SUB 9-pin
RS-232C cable
(246C548-10)
• Used for projector control
by computer.
Others
Remote control
cable
(246C424-10)
• Lens cap (Attached to the
projector)
• Terminal cover (750A561-10)
• Quick Start up (857D079-10)
• CD-ROM (919C151-10)
• Safety manual (871D468-10)
Power cord (two)
(246C483-10, 246C383-20)
Remote control
(290P136-20)
R6 (size-AA)
battery (two)
Important:
• The attached power cords are to be used exclusively for this product. Never use them for other products.
Inserting the batteries into the remote control
1. Remove the rear lid of the remote control.
1
3
2
CAUTION:
• Use of a battery of wrong type may cause explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
• Dispose of used batteries according to your local regulations.
• Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fi re.
• Be sure to handle the batteries according to the instructions.
• Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
• Keep batteries out of reach of children and pets.
• Remove the batteries, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in
contact with your eyes, rinse them with water and then consult your doctor.
2. Check the polarity (+), (-) of the batteries, and set them
correctly, inserting their (-) side fi rst.
• If the battery is inserted from the (+) side fi rst, inserting
the (-) side is diffi cult because the coil spring end hits on
the battery side. If the battery is forced to insert in this
way, the outer label of the battery may get ripped and it
may cause a short-circuit and heating.
3. Attach the rear lid.
Important:
• Use two size-AA batteries (R6).
• Replace the 2 batteries with new ones when the remote
control is slow to operate.
EN-6
Overview
1 2 6
Control panel
1
2
AUTO POSITION
3
COMPUTER
4
5
6
4 53
POWER
STATUS
ENTER
MENU
ZOOM/FOCUS LENS SHIFT
7 8
11
10
KEYSTONE
VIDEO
9
8
VOLUME
7
1 Speaker
2 Control panel (inside the cover)
3 Air outlet grille
4 Remote control sensor (Front)
5 Air inlet grille
6 Remote control sensor (Rear)
7 Terminal board
8 Air outlet grille
1 POWER button
2 AUTO POSITION / button
3 COMPUTER / button
4 KEYSTONE / ENTER button
5 MENU button
6 ZOOM / FOCUS button
7 LENS SHIFT button
8 VOLUME / button
9 VIDEO / button
10 POWER indicator
11 STATUS indicator
ENGLISH
Important:
• While the menu or the screen for the keystone, lens shift and zoom/focus adjustment, or password entry is being
displayed, the COMPUTER, VIDEO, AUTO POSITION and VOLUME buttons function as the , , and buttons respectively.
• While the menu is on the screen, the KEYSTONE button functions as the ENTER button.
Terminal board
2 3 4 5 6 71
9 11 13 14 16128 10 15
7 Kensington Security Lock Standard connector
8 Main power switch
O : Off I : ON
9 Power jack
10 USB terminal
11 SERIAL terminal (D-SUB 9-pin)
• Used for projector control by computer. Contact your dealer for details.
12 REMOTE IN / OUT jack
13 MONITOR OUT terminal (Mini D-SUB 15-pin)
14 AUDIO OUT terminal (Mini jack)
15 AUDIO IN-2 terminal (Mini jack)
16 VIDEO IN and AUDIO IN terminals
1 LAN terminal
• Used for projector control by computer.
2 COMPUTER / COMPONENT VIDEO DVI-D
(HDCP) terminal (DVI-D 24-pin)
3 COMPUTER / COMPONENT VIDEO IN-2 terminal
(R/PR, G/Y, B/PB, H/HV, V) (BNC)
4 COMPUTER / COMPONENT VIDEO IN-1 terminal
(Mini D-SUB 15-pin)
5 AUDIO IN-1 terminal (Mini jack)
6 Power terminal for wireless LAN unit (DC OUT
5V 1.5A MAX)
• Do not use the power terminal as a power for
other devices than the specifi ed wireless LAN unit.
(Wireless LAN unit isn’t packaged together with the
projector.)
EN-7
2
Preparating your projector (continued)
Bottom side
1
Remote control
30
10
11
12
13
14
15
1
2
3
4
5
COMPUTER
2
6
7
8
9
DVI-D(HDCP)
HOME Page Up
END Page Down
1
VIDEO S-VIDEO
AUTO POSITION
LASER
29
28
27
26
25
24
ENTER
R-CLICK
MENU
LENS SHIFTZOOM / FOCUS
KEYSTONE
VOLUME
ASPECT
PinP
EXPAND
STILL
MUTE
CE
23
22
21
20
19
18
17
1 Lamp cover
2 Adjustment feet
Caution:
Do not replace the lamp immediately after using the
projector because the lamp would be extremely hot
and it may cause burns.
1 Laser aperture
2 Transmission window
3 Wired remote control jack
4 Indicator
5 POWER button
6 VIDEO button
7 DVI-D(HDCP) button
8 HOME button
9 END button
10 Mouse pointer
11 LENS SHIFT button
12 MENU button
13 ZOOM/FOCUS button
14 + , - (VOLUME) buttons
15 COLOR ENHANCER (CE) button
16 MUTE button (Audio/Video)
17 EXPAND button
18 STILL button
19 PinP button
20 ASPECT button
21 KEYSTONE button
22 ENTER button
23 R-CLICK button
24 Direction buttons
25 LASER button
26 AUTO POSITION button
27 Page Up/Down buttons
28 S-VIDEO button
29 COMPUTER 1, 2 buttons
30 Left click button
16
• The + and - buttons are used in the KEYSTONE adjustment and the EXPAND mode in addition to the volume control.
• The direction buttons are also used for keystone and lens shift adjustments. The and buttons are also used
for adjustment of the sub image display position in the PinP mode and zoom/focus adjustment.
• Pressing the LASER button emits a laser beam. Even when you keep holding down the LASER button, it is emitted
only one minute. To keep emitting it longer, press the LASER button again.
• You can disable the LASER button to prevent laser radiation due to misuse of the button.
How to disable the LASER button
While holding the LASER button down, press the button 3 times.
How to enable the LASER button
While holding the LASER button down, press the button 3 times.
• Whenever the batteries are replaced, the LASER button is enabled.
About the laser beam
This remote control is a Class 2 laser product. (Max. output : 1 mW, Wavelength : 620-640 nm)
Beam Divergence : 6 m distance about 10.0 mm x 10.0 mm (±6.0 mm)
CAUTION :
• Pressing the LASER button on the remote control emits a laser beam. Do not look into the laser beam directly. Do
not point the laser beam at anyone. Looking at the laser beam directly may damage eyesight.
• Use of controls or adjustments or procedures other than those specifi ed herein may result in hazardous radiation exposure.
• This remote controller cannot be repaired.
EN-8
Using the remote control
20°
20°
Operational range of the remote control
Front of projector
30°30°
Rear of projector
• Keep the remote control photo-sensor out of direct
sunlight or fl uorescent lamp light.
• Keep the remote control photo-sensor at least 2 m
away from fl uorescent lamps. Otherwise, the remote
control may malfunction.
• If there is an inverter-operated fl uorescent lamp
near the remote control, the remote control opera-
30°30°
Operate the remote
control within a distance
of 10 m from the projector,
tion may become unstable.
• When you use the remote control too close to the
remote control sensor, the remote control may not
work correctly.
pointing the light beam at
the remote control photosensor (front or rear) of
the projector.
When operating the remote control, keep the
distance from the remote control to the projector
via the screen within about 7 m. The operable
range of the remote control, however, depends
on the characteristics of the screen.
ENGLISH
Reception angle
Vertical directions
20°
5°
20°
5°
Vertical directions (ceiling mount)
20°
20°
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operation area.
• When the remote control is connected with remote control cable, it does not as a wireless remote control.
• When using the wired remote control, the laser beam may be darker. It is normal.
• When REMOTE OUT terminal on
this projector is connected to the
REMOTE IN terminal on the other
projector, the two projectors can
be controlled together by using
the remote control. (Up to two
projectors can be controlled.)
REMOTE IN
REMOTE OUT
EN-9
Setting up your projector
Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the
projection angle of the projector. (See below.)
• Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of
the screen center.
• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly refl ecting on the screen
makes the projected images whitish and hard to view.
Basic setup
Determine the distance from the screen to the projector according to the size of the images to be projected. (See
page 12.)
• Do not place this projector on a carpet or blanket because the exhaust vent and the intake vent on the bottom
surface are blocked and the inside of the projector is heated, causing a breakdown or fi re.
• Depending on the installation conditions, warm air that is emitted from the exhaust vents may fl ow into the intake
vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images.
W
A
B
A=B
Adjusting the projection angle
This projector is provided with 2 feet for adjusting
the projection angle on the bottom surface. Adjust
the projection angle depending on the position of
the projector.
Adjustment of the projection angle
For the best projection, project images on a fl at
screen installed at 90 degrees to the fl oor. If
necessary, tilt the projector using 2 adjustment feet
on the bottom of the projector.
Screen
Adjustment feet
1. Tilt up the projector to the appropriate angle.
2. Rotate the adjustment feet for fi ne adjustment.
After using the projector:
3. Put the adjustment feet back into the projector
by rotating the adjustment feet.
• You can adjust the vertical and horizontal position
of the displayed image using the LENS SHIFT button. See page 12.
Keystone adjustment
• To correct vertical and horizontal keystone distortion, press the KEYSTONE button on the projector
or the remote control to display KEYSTONE, and
adjust the image by pressing the , , or
button (or VOLUME + or - button on the remote
control).
Press the
button.
Press the
button.
Press the
(or -) button.
Press the
(or +) button.
• You can correct the vertical and horizontal keystones at the same time. However, their adjustment ranges are limited in such correction.
• When the keystone adjustment is carried out, the
adjustment value is indicated. Note that this value
doesn't mean a projection angle.
• The allowable range of the adjustment value in
the keystone adjustment varies depending on the
installation conditions.
• When the keystone adjustment takes effect, the
resolution decreases. In addition, stripes may
appear or straight lines may bend in images with
complicated patterns. They are not due to product
malfunctions.
• Noise may appear on the screen during the keystone adjustment because of the type of the video
signal being projected and the setting values of
the keystone adjustment. In such cases, set the
keystone adjustment values in the range where
the image is displayed without noise.
• When the keystone adjustment is carried out, the
image may not be displayed correctly because of
the type of input signal.
• Displayed image may be distorted during keystone
adjustment.
• For proper keystone adjustment results, reset the
lens to the factory-adjusted position using LENS
SHIFT RESET in the INSTALLATION menu before
carrying out keystone adjustment. (See page 23.)
EN-10
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installation.
For details, consult your dealer.
• The warranty on this projector does not cover any
damage caused by use of any non-recommended
ceiling mount kit or installation of the ceiling mount
kit in an improper location.
• When using the projector mounted on the ceiling,
set IMAGE REVERSE in the INSTALLATION menu to
MIRROR INVERT. See page 23.
• When the projector is mounted on the ceiling, images may appear darker than those projected in
the case of tabletop mounting. This isn't a product
malfunction.
• Ask your installation specialist to provide a breaker.
When you do not use the projector, be sure to shut
down the main power by the breaker.
• Do not install the projector where the exhaust vents
are exposed to air emitted by an air conditioning.
Such installation may cause a breakdown.
• Do not install the projector near a fi re alarm because
it emits hot air from its exhaust vents.
Caution:
• Placing the projector directly on a carpet impairs
ventilation by the fans, causing damage or failure.
Put a hard board under the projector to facilitate
ventilation.
• Place the projector at least 50 cm (or 20 inches)
away from the wall to prevent the air inlet grille and
the air outlet grilles that emit hot air from being
blocked.
• Do not use the projector in the following locations
and manners, which may cause fi re or electric
shock.
• In a dusty or humid place.
• In a sideways or upside-down position.
• Near a heater.
• In an oily, smoky, or damp place such as a kitchen.
• In direct sunlight.
• Where the temperature rises high, such as in a
closed car.
• Where the temperature is lower than +41ºF (or
+5ºC) or higher than +104ºF (or +40ºC ).
Important:
• We don’t recommend using the projector at an altitude of 1500 meters or higher. Use at an altitude of
1500 meters or higher may affect the projector’s life.
ENGLISH
Rear projection
Ask a specialist for installation. For details, consult
your dealer.
• For rear projection, set IMAGE REVERSE in the INSTALLATION menu to MIRROR. See page 23.
EN-11
Setting up your projector (continued)
Screen size and projection distance
Refer to the following table to determine the screen size.
Front projection Front projection, ceiling mounting
W
H
H1 H2
L
W1W1
H1H2
H
L
L
W
W1W1
L
When the aspect ratio of the screen is 4:3
Screen size
4:3 Diagonal size Height (H) Width (W) Min. Max. (H1) (H2) width (W1)
inch cm inch cm inch cm inch m inch m inch cm inch cm inch cm
40 102 24 61 32 81 54 1.4 74 1.9 12 30 2 6 3 8
60 152 36 91 48 122 82 2.1 112 2.8 18 46 3 9 5 12
80 203 48 122 64 163 110 2.8 150 3.8 24 61 4 11 6 16
100 254 60 152 80 203 138 3.5 189 4.8 30 76 6 14 8 20
150 381 90 229 120 305 208 5.3 284 7.2 45 114 8 21 12 30
200 508 120 305 160 406 279 7.1 380 9.7 60 152 11 28 16 41
250 635 150 381 200 508 349 8.9 476 12.1 75 191 14 36 20 51
300 762 180 457 240 610 419 10.6 571 14.5 90 229 17 43 24 61
• The above fi gures are approximate and may be slightly different from the actual measurements.
• The lens movable range shows distances from the factory default position.
Projected distance (L) Lens movable range
LENS SHIFT button
To adjust the positions of the projector and the screen, use LENS SHIFT button.
1. Press the LENS SHIFT button.
2. Press the , , or button to move the image position.
Every time the button is pressed, the image moves down.
Every time the button is pressed, the image moves up.
Every time the button is pressed, the image moves to the right.
Every time the button is pressed, the image moves to the left.
• When you hold down these buttons for 2 seconds or longer, the displayed image moves fast in the corresponding
directions.
• Be careful not to be caught in the opening in the lens while the lens is moving.
EN-12
Viewing computer images
A. Connecting the projector to a computer
Preparation:
• Make sure that the power of the projector and that of the computer are turned off.
• When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor.
COMPUTER IN/COMPONENT
VIDEO IN-1
1
COMPUTER IN/COMPONENT
VIDEO IN-2
424); $2$**8 8
1
DVI-D (HDCP)
1
2
2
2
to monitor port
RGB cable
8 **8 $2
to DVI
DVI cable
$
); 42
to monitor port
(5 BNC)
4
For analog connection:
(For using the COMPUTER/COMPONENT VIDEO IN-1
terminal.)
1. Connect one end of the supplied RGB cable to the
COMPUTER IN/COMPONENT VIDEO IN-1 terminal of the
projector.
2. Connect the other end of the RGB cable to the monitor
port of the computer.
• When viewing images supplied from an analog-connected
computer, press the COMPUTER button on the remote
control.
For analog connection:
(For using the COMPUTER/COMPONENT VIDEO IN-2
terminal.)
1. Connect one end of a commercially BNC cable to the
COMPUTER IN/COMPONENT VIDEO IN-2 terminal of the
projector.
2. Connect the other end of the BNC cable to the 5 BNC
terminals of the monitor port of the computer.
For digital connection:
1. Connect one end of a commercially available DVI cable to
the DVI-D (HDCP) terminal of the projector.
2. Connect the other end of the DVI cable to the DVI terminal
of the computer.
• When viewing images supplied from a digital-connected
computer, press the DVI-D(HDCP) button on the remote
control.
• Turn on the main power switch of the projector before
starting the computer.
ENGLISH
For audio connection:
1. Connect one end of a commercially available PC audio
cable to the AUDIO IN-1/2 terminal of the projector.
Computer
2. Connect the other end of the PC audio cable to the audio
output terminal of the computer.
• This projector uses stereo pin jack for its audio input. Check
the type of the audio output terminal of the connected
1
AUDIO IN
PC audio cable (option)
2
AUDIO OUT
to audio output
terminal
computer and prepare a proper cable for connection. Some
computers don't have the audio output terminal.
• Speaker output is mono.
• Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending
on the type of the computer to be connected.
• Use of a long cable may decrease the quality of projected images.
• Images may not be projected correctly, depending on the type of the connected computer.
• When DVI-D signal is input, some signal setting menus are unavailable.
• Also read the instruction manual of the equipment to be connected.
• Contact your dealer for details of connection.
EN-13
Loading...