Mitsubishi Electronics WB-PA5 Installation Manual

MANUFACTURED FOR:

Installation Instructions

Wind Baffle Part # WB-PA2

1. Remove 5 screws holding fan guard in place.

2. Slide fan guard into wind baffle lining up the stopper tabs.

3. Position wind baffle/fan guard and line up with pre-punched holes.

4. Install all 5 screws and tighten securely. Repeat with all baffles.

Note: When two fan outdoor unit is used, two wind baffles are required.

Install lower baffle first for easier installation.

WARNING! MOVING PARTS. INCORRECT HANDLING COULD LEAD TO DEATH OR INJURY!

IMPORTANT! Outdoor Unit should be installed with back coil surface facing a wall or oriented

so the wind does NOT blow directly on to the back coil surface. Do not install this product

where there is any obstacle at either side or above the outdoor unit. If the discharge air is

obstructed the air may be short cycled.

Steps:

ENSURE BAFFLE OUTLETS WILL NOT BE BLOCKED OR OBSTRUCTED !

5. Attach the safety string to the lower left inside of baffle using the pre-punched hole and the provided 10-24 screw and nylon lock nut. Attach the other end to the closest

existing cabinet screw. Repeat with all baffles.

Installation Instructions

Wind Baffle Part # WB-PA2

1. Remove 5 screws holding fan guard in place.

2. Slide fan guard into wind baffle lining up the stopper tabs.

3. Position wind baffle/fan guard and line up with pre-punched holes.

4. Install all 5 screws and tighten securely. Repeat with all baffles.

Note: When two fan outdoor unit is used, two wind baffles are required.

Install lower baffle first for easier installation.

STEP 1 STEP 2

STEP 3 STEP 4

WARNING! MOVING PARTS. INCORRECT HANDLING COULD LEAD TO DEATH OR INJURY!

IMPORTANT! Outdoor Unit should be installed with back coil surface facing a wall or oriented

so the wind does NOT blow directly on to the back coil surface. Do not install this product

where there is any obstacle at either side or above the outdoor unit. If the discharge air is

obstructed the air may be short cycled.

Steps:

ENSURE BAFFLE OUTLETS WILL NOT BE BLOCKED OR OBSTRUCTED !

5. Attach the safety string to the lower left inside of baffle using the pre-punched hole and the provided 10-24 screw and nylon lock nut. Attach the other end to the closest

existing cabinet screw. Repeat with all baffles.

MITSUBISHI ELECTRIC US, INC.

Wind Bafe

WB-PA5

for use with:

PUY/Z-A24/30/36NHA4/NHA6; PUY/Z-A42NHA4/NHA5 PUZ-HA30/36NA4; PUMY-P36/48NHMU; PUY/Z-A24/A30NHA7

Outdoor Units

INSTALLATION MANUAL

For safe and correct use, please read this installation manual thoroughly before installing the advanced wind bafes.

FOR INSTALLER

WARNING! MOVING PARTS. INCORRECT HANDLING COULD LEAD TO DEATH OR INJURY!

IMPORTANT! Outdoor Unit should be installed with back coil surface facing a wall or oriented so the wind

does NOT blow directly on to the back coil surface. Do not install this product where there is any obstacle at

either side or above the outdoor unit. If the discharge air is obstructed the air may be short cycled.

STEPS:

1. Remove four(4) or ve(5) screws holding fan guard in place.

2. Slide fan guard into wind bafe lining up the stopper tabs.

3. Position wind bafe/fan guard and line up with pre-punched holes.

4. Install all four(4) or ve(5) screws and tighten securely. Repeat with all bafes.

ENSURE BAFFLE OUTLETS WILL NOT BE BLOCKED OR OBSTRUCTED !

Note: When two fan outdoor unit is used, two wind bafes are required. Install lower bafe rst for easier installation.

English

STEP 1 STEP 2

stopper

stopper or wire tab

This product is designed and intended for use in commercial and

light-industrial environment.

Please be sure to put the contact address/telephone number on

this manual before handing it to the customer.

Manufactured for MITSUBISHI ELECTRIC US, INC.

www.mitsubishielectric-usa.com

Toll Free: 800-433-4822

Wind Bafe WB-PA5 Installation Instructions, February 2017