ENGLISH
DLP
MODEL
TM
DATA DISPLAY
VS-50PH50U
VS-67PH50U
VS-67PHF50U
User’s Manual
VS-67PH50U-SN
SC-067PH50U
VS-67PHF50U-SN
SC-067PHF50U
FRANÇAIS
)(
ESPAÑOL
)(
PORTUGUES
ITALIANO
Be sure to follow the directions below.
Warning:
This user’s manual is important to you. Please read it before using your product.
This user’s manual is important to you. Please read it before using your product.
For MITSUBISHI dealer
Please read Set-up and Installation Manual before installing the product.
Trademarks
This product requires special installation to prevent
toppling.
Please ask installation specialists for installation.
Don’t attempt to install the product by yourself.
SVENSKA
DEUTSCH
All brand names and product names herein are trademarks or registered trademarks of their respective companies.
• DLP and DLP logo are trademarks of Texas instruments.
EN-1
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PRODUCT IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET MUST BE INSTALLED NEAR THE EQUIPMENT AND SHOULD BE EASILY ACCESSIBLE.
EN-2
Important safeguards
Please read all these instructions regarding your
DLPTM data display and retain them for future
reference. Follow all warnings and instructions
marked on the DLPTM data display.
1. Read instructions
All the safety and operating instructions
should be read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should
be retained for future reference.
3. Warnings
All warnings on the appliance and in the
operating instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug the power cord from the wall outlet
before cleaning it. Do not use liquid aerosol
cleaners. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire,
electric shock or other personal injury.
7. Water and moisture
Do not use this product near water or in
contact with water.
8. Accessories
Do not place this product on an unstable cart,
stand, tripod, bracket or table. Use only with
a cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the
product. Any mounting of the appliance
should follow the manufacturer’s instructions
and should use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force
and uneven surfaces may cause the appliance
and cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided for ventilation, ensuring reliable operation of the product and to protect it from
overheating. Do not block these openings or
allow them to be blocked by placing the
product on a bed, sofa, rug, or bookcase.
Ensure that there is adequate ventilation and
that the manufacturer’s instructions have
been adhered to.
10. Power sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power, please consult your appliance dealer
or local power company.
11. Power-cord protection
Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them. Pay
particular attention to cords at plugs, convenience receptacles, and points where they exit
from the appliance.
12. Overloading
Do not overload wall outlets and extension
cords as this can result in a fire or electric
shock.
13. Objects and liquids
Never push objects of any kind through
openings of this product as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
14. Servicing
Do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
15. Damage requiring service
Unplug the power cord from the wall outlet
and refer servicing to qualified service personnel under the following conditions:
(a) If the power-supply cord or plug is dam-
aged.
(b) If liquid has been spilled, or objects have
fallen into the product.
(c) If the product does not operate normally
after you follow the operating instructions. Adjust only those controls that are
covered by the operating instructions. An
improper adjustment of other controls
may result in damage and may often
require extensive work by a qualified
technician to restore the product to its
normal operation.
(d) If the product has been exposed to rain or
water.
(e) If the product has been dropped or the
cabinet has been damaged.
(f) If the product exhibits a distinct change
in performance - this indicates a need for
service.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement parts specified by the manufacturer or
parts having the same characteristics as the
original part. Unauthorized substitutions
may result in fire, electric shock or other
hazards.
17. Safety check
Upon completion of any service or repair to
this product, ask the service technician to
perform safety checks determining that the
product is in a safe operating condition.
ENGLISH
EN-3
WARNING:
Unplug immediately if there is
something wrong with your product.
Do not operate if smoke, strange noise or odor
comes out of your product. It might cause fire or
electric shock. In this case, unplug immediately
and contact your dealer.
Never remove the cabinet.
This product contains high voltage circuitry. An
inadvertent contact may result in an electric
shock. Except as specifically explained in the
Owner’s Guide, do not attempt to service this
product yourself. Please contact your dealer when
you want to fix, adjust or inspect the product.
Do not modify this equipment.
It can lead to fire or electric shock.
Use the optional specified power supply
cord.
This apparatus must be grounded.
Place the product more than 5 cm (2 in.)
from the wall (except at the rear) to
prevent blocking the intake, exhaust slots
and ventilation of this product because
hot air comes out of it.
Carry the product by all four handles,
not by two handles.
Do not use the product under the
following circumstances, which may
cause fire or electric shock.
• in a dusty or humid place
• near a heater
• in a oily, smoky or damp place
• in direct sunlight
• with high temperature, such as the closed car
• where the temperature is lower than 10˚C
(50˚F) or higher than 35˚C (95˚F)
• for VS-67PHF50U the temperature is lower
than 10˚C (50˚F) or higher than 30˚C (86˚F)
CAUTION:
Battery replacement of the optional remote
control R-XL50TX
•Improper use may result in fire, injury, or spread
dirt due to leakage, heat generation, or explosion.
• Replace all the batteries with new ones. Use two
AA batteries (R6P).
• Load the batteries with their (+) and (-) sides
correctly.
• Load the batteries from (-) sides first.
NOTE:
This symbol mark is for EU countries only.
This symbol mark is according to
the directive 2002/96/EC Article 10
Information for users and Annex IV.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and
reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed
of separately from your household waste.
Please, dispose of this equipment at your local
community waste collection/recycling centre.
In the European Union there are separate collection systems for used electrical and electronic
product.
Please, help us to conserve the environment we
live in!
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the
Department of Communications.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate
this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class A digital apparatus complies with Canadian ICES-003.
COMPLIANCE NOTICE OF EC DIRECTIVE
This data display complies with requirements of 89/336/EEC, 2006/95/EC and 93/68/EEC. The requirements of susceptibility have chosen at a level, that makes interference free operation possible in living
areas, office areas and light industry, related to indoor and outdoor operation. All places of operation are
related to the public low voltage power supply.
This is a equipment of Class A. This device could cause interferences in residential areas; in the case of
interferences it can be demand from the user to provide appropriate solutions and pay for it.
Warning:
This is class A information technology equipment. When used in a household environment, this product
may cause radio interface. In such a case, the user may be required to take suitable countermeasures.
EN-4
Specifications / Items sold separately
Model
Screen size
RGB input signal supported
Analog RGB input
Digital RGB input
Control
Power consumption
Power supply
External dimensions
(excluding protrusions)
Operating temperature and
humidity
Weight
Accessories
Terminal
Signal
Terminal
Signal
Width
Height
Depth
VS-50PH50U
50 inches (1015 x 761 mm)
Resolution: VGA . SXGA+ Horizontal: 31.5 to 78 kHz, Vertical: 49.5 to 85 Hz,
Pixel clock rate: 25 to 122 MHz
RGB signal level: 0.7 V(p-p) 75 ., Sync: TTL level (positive/negative)Sync On Green
Mitsubishi original control link: D-Sub 9-pin x 2 (input and output)
AC 100 V – 240 V 50/60 Hz 2.5 A
1016 mm (40.0 inch)
977 mm (38.5 inch)
639 mm (25.1 inch)
10˚C – 35˚C (50˚F – 95˚F)
20 % – 80 %
64 kg (141 lbs)
User’s manual,
Joint parts (8 pcs. each of hexagon socket head cap screws for M6, flat washers, and
spring washers),
Control cable,
Joint hole seal,
Plastic tie (10 pcs. for VS-67PHF50U)
1361 mm (53.6 inch)
1282.3 mm (50.5 inch)
778 mm (30.6 inch)
91 kg (201 lbs)
VS-67PH50U
67 inches (1359 x 1019 mm)
BNC x 5 (RGBHV)
DVI-D
TMDS
RS-232C: D-Sub 9-pin
195 W
VS-67PHF50U
1362 mm (53.6 inch)
1282.3 mm (50.5 inch)
848 mm (33.4 inch)
10˚C – 30˚C (50˚F – 86˚F)
20 % – 70 %
97 kg (214 lbs)
ENGLISH
Design and specifications are subject to change without notice.
Option
• Remote control for wireless and wired use : R-XL50TX
• Lamp for replacement : S-PH50LA
• Power cord (North America) : JC-PC3MA (125 V 10 A)
• Power cord (Europe) : JC-PC3ME (250 V 10 A)
• Power cord (China) : JC-PC3MC (250 V 10 A)
• Screen unit : SC-067PH50B (VS-67PH50U)
SC-067PHF50B (VS-67PHF50U)
EN-5
Lamp replacement
This product is equipped with the lamp to display images generated by DLPTM chip. This lamp is a
consumable and it may lose its intensity or burn out during use. When the lamp intensity decreases, this
product detects such decrease and switches the lamp to the built-in spare lamp automatically. (This
function is called automatic lamp changer.) While the spare lamp is in use, a mark “ ” blinks on the
screen. (When the spare lamp burns out, a blue light blinks on the screen and “1” is displayed on the
status display on the rear terminal panel.) When the spare lamp burns out, contact your MITSUBISHI
dealer for replacement of the lamp and the adjustments for ensuring the same level of image quality as
that before lamp replacement (such as the screen frame adjustment, CSC adjustment, and gradation
adjustment).
Do not attempt to replace the lamp and carry out the adjustments by yourself.
This product uses a lamp that contains mercury. Disposal of the lamp or the product with the lamp may be
regulated due to environmental considerations. For disposal or recycling infomation, please contact your
local authorities or Electronic Industries Alliance : www.eiae.org.(For US only)
Troubleshooting
Please check the following before contacting your dealer for service. Errors in signals are apt to be taken
for problems in the product.
RemediesProblems
No image appears
on the screen.
Hue of the image is
not appropriate.
• Check the power cord is connected firmly.
• Check the correct input signals are selected for the terminals of the
external devices.
• Check the external devices are connected to the terminals firmly.
• Check the external devices are turned on.
• Check the appropriate signal is input from the external devices to the
product.
• Check the signal connection between the external device and the
product.
EN-6
Troubleshooting (continued)
Problems Remedies
A blue light blinks
on the screen,
without image
display.
• When the lamp burns out or a failure occurs in the product, a blue light blinks on the screen. In
such a case, check the state of the blinking blue light and the state of the status display on the
rear terminal panel (except VS-67PHF50U) according to the following table.
State of the
blinking
blue light
State of the
status
display
STATUS
STAND BY
STATUS
STAND BY
STATUS
The lamp has burnt out, or the lamp drive circuit has
failed.
Contact your MITSUBISHI dealer.
The lamp has not been installed or not been installed
properly.
Contact your MITSUBISHI dealer.
Causes and solutions
VS-50PH50U
VS-67PH50U
ENGLISH
VS-67PHF50U
The lamp has burnt out
or not been installed or
not been installed
properly, or the lamp
drive circuit has failed.
Contact your
MITSUBISHI dealer.
Light on for
1 second, off
for 1 second
Light on for
5 seconds, off
for 1 second
Light on for
1 second, off
for 5 seconds
STAND BY
Displays number
2, 3, 4, 5 or 6.
STATUS
STAND BY
STATUS
STAND BY
STATUS
STAND BY
STATUS
STAND BY
STATUS
STAND BY
STATUS
STAND BY
Displays number
1, 2, 3, 4 or 5.
STATUS
STAND BY
The cover of the lamp changer is open.
Contact your MITSUBISHI dealer.
The color wheel has failed.
The lamp changer has failed.
Contact your MITSUBISHI dealer.
The power circuit has failed.
Contact your MITSUBISHI dealer.
The lamp power control circuit has failed.
Contact your MITSUBISHI dealer.
The cooling fan has failed.
Contact your MITSUBISHI dealer.
The image processing circuit has failed.
Contact your MITSUBISHI dealer.
The color wheel has
failed.
Contact your
MITSUBISHI dealer.
The power circuit, cooling
fan, or image processing
circuit has failed.
Contact your
MITSUBISHI dealer.
• VS-67PHF50U
During image
display, text is
displayed on the
screen.
OVER TEMP
CHECK FILTER
• The ambient temperature may be too high, or the filter may be clogged.
Confirm the display on the screen and take the required measures.
Causes and solutionsState of the word
OVER TEMP
OVER TEMP
CHECK FILTER
White text, lit
Red text, flashing
White text, lit
The ambient temperature has risen or the filter has become clogged.
Contact your MITSUBISHI dealer.
The ambient temperature has risen abnormally or the filter has become clogged.
Stop the operation immediately and contact your MITSUBISHI dealer.
The filter must be inspected.
Contact your MITSUBISHI dealer.
EN-7
Mitsubishi Electric Corporation
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
Printed in Japan
871D430D80
Loading...