Mitsubishi Triton (2018), Triton (2019) Owner’s Manual

Download

Page 1

OKTE20E1

L200

Owner’s Manual

L200 - ENGLISH  OKTE20E1

Printed in the Netherlands

MITSUBISHI MOTORS

19-000228_OKTE20E1_L200_OM-Cover_eng_2019_rug-25,1mm.indd All Pages 17/06/19 16:37

Page 2

Foreword

Thank you for selecting a

MITSUBISHI L200 as your new vehicle. This owner’s manual will add to your understanding and full enjoyment of the many fine features of this vehicle. It contains information prepared to acquaint you with the proper way to operate and maintain your vehicle for the utmost in driving pleasure.

MITSUBISHI MOTORS Europe B.V. reserves the right to make changes in design and specifications and/or to make additions to or improvements in this product without obligation to install them on products previously manufactured. It is an absolute requirement for the driver to strictly observe all laws and regulations concerning vehicles.

This owner’s manual has been written in compliance with such laws and regulations, but some of the contents may become contradictory with later amendment of the laws and regulations.

Please leave this owner’s manual in this vehicle at time of resale. The next owner will appreciate having access to the information contained in this owner’s manual.

Repairs to your vehicle: Vehicles in the warranty period: All warranty repairs must be carried out by a MITSUBISHI MOTORS Authorised Service Point.

Vehicles outside the warranty period: Where the vehicle is repaired is at the owner’s discretion.

Throughout this owner’s manual the words W

ARNING and CAUTION appear. These serve as reminders to be especially careful. Failure to follow instructions could result in personal injury or damage to your vehicle.

WARNING

Indicates a strong possibility of severe personal injury or death if instructions ar

e not followed.

CAUTION

Means hazards or unsafe practices that could cause minor personal injury or damage to your vehicle.

ou will see another important symbol:

NOTE

Gives helpful information. *: Indicates optional equipment.

It may differ according to the sales classification; refer to the sales catalogue. Abbreviations used in this owner’s manual:

LHD: Left-Hand Drive RHD: Right-Hand Drive M/T: Manual Transmission A/T: Automatic Transmission

The symbol used on the vehicles:

: See owner’s manual

Information for station service

Fuel

Fuel tank capacity 75 litres

Recommended fuel

Cetane number (EN590)

51 or higher

Refer to the “General information” section for the fuel selection.

Engine oil Refer to the “Maintenance” section for the selection of engine oil.

Tyre inflation pressure Refer to the “Maintenance” section for the tyre inflation pressure.

OKTE20E1

BLO-19-000228

Page 3

Overview/Quick guide

General information

Locking and unlocking

Seat and seat belts

Instruments and controls

Starting and driving

For pleasant driving

For emergencies

Vehicle care

Maintenance

Specifications

Alphabetical index

Declaration of Conformity

OKTE20E1

Page 4

Instruments and Controls (Driver’s area)

1. Instruments p. 5-02

2. Shift paddles* p. 6-34

3. Headlamp washer switch* p. 5-68 Wiper and washer switch p. 5-64

4. Cruise control switches* p. 6-80 Speed Limiter control switches* p. 6-85

5. Multi information display switch* p. 5-04

6. Bluetooth® 2.0 interface* p. 7-74

7. Active stability control (ASC) OFF switch p. 6-76

8. Fuel tank filler door release lever* p. 2-03

9. Bonnet release lever p. 10-03

10. Electric window control switch* p. 3-21

11. Lock switch* p. 3-22

12. Lane departure warning (LDW) switch* p. 6-112

13. Forward Collision Mitigation system (FCM) and Ultrasonic misacceleration Mitigation system (UMS) ON/OFF switch* p. 6-94

14. Headlamp leveling switch p. 5-61

15. Outside rear-view mirrors switch* p. 6-09

16. Ignition switch* p. 6-12 Engine switch* p. 6-13

17. Combination headlamps and dipper switch p. 5-55 Automatic High-Beam (AHB) switch* p. 5-58 Turn-signals lever p. 5-62 Front fog lamp switch* p. 5-63 Rear fog lamp switch* p. 5-63

18. Multi Around Monitor operation switch* p. 6-128 Audio remote control switches* p. 7-75

19. Horn switch p. 5-70 Supplemental restraint system (SRS) - airbag (for driver’s seat) p. 4-24, 4-28

Instruments and Controls (Driver’s area)

1-02

OKTE20E1

Overview/Quick guide

Page 5

Instruments and Controls

LHD Type 1

1. Audio* p. 7-18, 7-39 Digital clock* p. 7-99

2. Centre ventilators p. 7-03

3. Heater*/Manual air conditioning* p. 7-05

4. Front passenger’s airbag indicator p. 4-24, 4-26

5. Supplemental restraint system (SRS) - airbag (for front passenger’s seat) p. 4-24, 4-27

6. Side ventilators p. 7-03

7. Glove box p. 7-102

8. Cigarette lighter p. 7-97

9. USB input terminal* p. 7-92

10. Key slot* p. 6-21

11. Centre console under tray p. 7-101, 7-102

12. Parking brake lever p. 6-05

13. Cup holder p. 7-104

14. Floor console box p. 7-101, 7-103 Accessory socket p. 7-98

15. Easy Select 4WD* p. 6-37

16. Gearshift lever* p. 6-29 Selector lever* p. 6-31

17. Auto Stop & Go (AS&G) OFF switch* p. 6-25

18. Rear differential lock switch* p. 6-54

19. Heated seat switch* p. 4-03

20. Hazard warning flasher switch p. 5-62

21. Rear window demister switch p. 5-68

Instruments and Controls

1-03

OKTE20E1

Overview/Quick guide

Page 6

LHD Type 2

1. Audio* p. 7-18, 7-39 Digital clock* p. 7-99 DISPLAY AUDIO*, MITSUBISHI Multi-Communication System (MMCS)*, Smartphone Link Display Audio* Refer to the separate owner’s manual

2. Rear window demister switch p. 5-68

3. Centre ventilators p. 7-03

4. Supplemental restraint system (SRS) - airbag (for front passenger’s seat) p. 4-24, 4-27

5. Side ventilators p. 7-03

6. Glove box p. 7-102

7. Hazard warning flasher switch p. 5-62

8. Front passenger’s airbag indicator p. 4-24, 4-26

9. Auto Stop & Go (AS&G) OFF switch* p. 6-25

10. Rear differential lock switch* p. 6-54

11. Cigarette lighter p. 7-97

12. USB input terminal* p. 7-92 HDMI terminal* p. 7-95

13. Heated seat switch* p. 4-03

14. Sonar switch* p. 6-117, 6-121

15. Blind Spot Warning switch* p. 6-106

16. Heated steering wheel switch* p. 5-70

17. Centre console under tray p. 7-101, 7-102

18. Parking brake lever p. 6-05

19. Cup holder p. 7-104

20. USB port (for changing)* p. 7-98

21. Floor console box p. 7-101, 7-103 Accessory socket p. 7-98

22. Off Road mode-selector* p. 6-53 Hill Descent Control switch* p. 6-70

23. Easy Select 4WD* p. 6-37 Super Select 4WD II* p. 6-46

24. Gearshift lever* p. 6-29 Selector lever* p. 6-31

25. Key slot* p. 6-21

26. Automatic air conditioning p. 7-10

Instruments and Controls

1-04

OKTE20E1

Overview/Quick guide

Page 7

RHD Type 1

1. Audio* p. 7-18, 7-39 Digital clock* p. 7-99

2. Heater*/Manual air conditioning* p. 7-05

3. Front passenger’s airbag indicator p. 4-24, 4-26

4. Hazard warning flasher switch p. 5-62

5. Cigarette lighter p. 7-97

6. USB input terminal* p. 7-92

7. Parking brake lever p. 6-05

8. Floor console box p. 7-101, 7-103 Accessory socket p. 7-98

9. Cup holder p. 7-104

10. Easy Select 4WD p. 6-37

11. Gearshift lever p. 6-29

12. Centre console under tray p. 7-101, 7-102

13. Key slot* p. 6-21

14. Rear differential lock switch* p. 6-54

15. Heated seat switch* p. 4-03

16. Glove box p. 7-102

17. Side ventilators p. 7-03

18. Supplemental restraint system (SRS) - airbag (for front passenger’s seat) p. 4-24, 4-27

19. Auto Stop & Go (AS&G) OFF switch p. 6-25

20. Centre ventilators p. 7-03

21. Rear window demister switch p. 5-68

Instruments and Controls

1-05

OKTE20E1

Overview/Quick guide

Page 8

RHD Type 2

1. Audio* p. 7-18, 7-39 Digital clock* p. 7-99 Smartphone Link Display Audio*, MITSUBISHI Multi-Communication System (MMCS)*, DISPLAY AUDIO* Refer to the separate owner’s manual

2. Automatic air conditioning p. 7-10

3. Rear window demister switch p. 5-68

4. Front passenger’s airbag indicator p. 4-24, 4-26

5. Centre console under tray* p. 7-101, 7-102

6. Gearshift lever* p. 6-29 Selector lever* p. 6-31

7. Parking brake lever p. 6-05

8. Floor console box p. 7-101, 7-103 Accessory socket p. 7-98

9. USB port (for changing)* p. 7-98

10. Cup holder p. 7-104

11. Off Road mode-selector* p. 6-53 Hill Descent Control switch* p. 6-70

12. Easy Select 4WD* p. 6-37 Super Select 4WD II* p. 6-46

13. Key slot* p. 6-21

14. Hazard warning flasher switch p. 5-62

15. Heated steering wheel switch* p. 5-70

16. Auto Stop & Go (AS&G) OFF switch p. 6-25

17. Rear differential lock switch* p. 6-54

18. Cigarette lighter p. 7-97

19. USB input terminal* p. 7-92 HDMI terminal* p. 7-95

20. Heated seat switch* p. 4-03

21. Blind Spot Warning switch* p. 6-106

22. Sonar switch* p. 6-117, 6-121

23. Glove box p. 7-102

24. Side ventilators p. 7-03

25. Supplemental restraint system (SRS) - airbag (for front passenger’s seat) p. 4-24, 4-27

26. Centre ventilators p. 7-03

Instruments and Controls

1-06

OKTE20E1

Overview/Quick guide

Page 9

Interior

Club cab

1. Inside rear-view mirror p. 6-08

2. Room lamp (front)* p. 7-99, 10-26, 10-34 Map lamps* p. 7-99, 10-26, 10-34 Sunglasses holder* p. 7-101, 7-104

3. Microphone* p. 7-75

4. Room lamp (rear) p. 7-99, 10-26, 10-34

5. Supplemental restraint system (SRS) - curtain airbag* p. 4-24, 4-31

6. Seat belts p. 4-07 Adjustable seat belt anchor p. 4-10

7. First-aid kit and warning triangle securing bands* p. 7-106

8. Jack p. 8-12

9. Jack handle p. 8-12

10. Rear seats* p. 4-04

11. Tools p. 8-13

12. First-aid kit and warning triangle securing bands* p. 7-106

13. Head restraints p. 4-05

14. Supplemental restraint system (SRS) - side airbag* p. 4-24, 4-30

15. Front seats p. 4-02

16. Supplemental restraint system (SRS) - front knee airbag (for driver’s seat)* p. 4-24, 4-27

17. Fuses p. 10-18

18. Steering wheel height and reach adjustment lever p. 6-07

19. Sun visors p. 7-96 Card holder p. 7-96 Vanity mirror p. 7-96

Interior

1-07

OKTE20E1

Overview/Quick guide

Page 10

Double cab

1. Inside rear-view mirror p. 6-08

2. ERA-GLONASS* p. 8-02 Room lamp (front) p. 7-99, 10-26, 10-34 Map lamps p. 7-99, 10-26, 10-34 Sunglasses holder p. 7-101, 7-104

3. Microphone* p. 7-75

4. Room lamp (rear) p. 7-99, 10-26,10-34

5. Supplemental restraint system (SRS) - curtain airbag* p. 4-24, 4-31

6. Seat belts p. 4-07 Adjustable seat belt anchor p. 4-10

7. Armrest p. 4-04 Cup holder p. 7-104

8. Jack p. 8-12

9. Jack handle p. 8-12

10. Tools p. 8-13

11. First-aid kit and warning triangle securing bands p. 7-106

12. Rear seats p. 4-04

13. Head restraints p. 4-05

14. Supplemental restraint system (SRS) - side airbag (for front seat)* p. 4-24, 4-30

15. Front seats p. 4-02

16. Supplemental restraint system (SRS) - driver’s knee airbag* p. 4-24, 4-27

17. Fuses p. 10-18

18. Steering wheel height and reach adjustment lever p. 6-07

19. Sun visors p. 7-96 Card holder p. 7-96 Vanity mirror p. 7-96

Interior

1-08

OKTE20E1

Overview/Quick guide

Page 11

Exterior - front

Club cab

Halogen headlamps type A Halogen headlamps type B LED headlamps type

1. Fuel tank filler door* p. 2-03

2. AdBlue™ tank filler lid p. 10-11

3. Keyless entry system* p. 3-04 Keyless operation system* p. 3-08 Locking and unlocking p. 3-15 Dead Lock System* p. 3-18

4. Outside rear-view mirrors p. 6-09

5. Side turn-signal lamps (on outside rear-view mirror)* p. 5-62, 10-25

6. Side turn-signal lamps (on fender)* p. 5-62, 10-25

7. Headlamps, high/low beam p. 5-55, 10-25

8. Position lamps/Daytime running lamps p. 5-55, 5-57, 10-25

9. Front turn-signal lamps p. 5-62, 10-25, 10-30

10. Front fog lamps p. 5-63, 10-25, 10-30

11. Headlamps, low beam p. 5-55, 10-25, 10-26

12. Headlamps, high-beam p. 5-55, 10-25, 10-26

13. Position lamps p. 5-55, 10-25, 10-29

14. Front turn-signal lamps p. 5-62, 10-25, 10-30

15. Daytime running lamps p. 5-57, 10-25, 10-30

16. Front fog lamps* p. 5-63, 10-25, 10-30

17. Headlamps, low beam p. 5-55, 10-25, 10-26

18. Headlamps, high-beam p. 5-55, 10-25, 10-26

19. Position lamps p. 5-55, 10-25, 10-29

20. Front turn-signal lamps p. 5-62, 10-25, 10-30

21. Front fog lamps* p. 5-63, 10-25, 10-30 Daytime running lamp p. 5-57, 10-25, 10-30

22. Bonnet p. 10-03 Engine compartment p. 10-02, 11-15

23. Wiper and washers p. 5-64, 10-17

24. Rain sensor* p. 5-65

25. Antenna p. 7-73

Exterior - front

1-09

OKTE20E1

Overview/Quick guide

Page 12

Double cab

Halogen headlamps type A Halogen headlamps type B LED headlamps type

1. Fuel tank filler door* p. 2-03

2. AdBlue™ tank filler lid p. 10-11

3. Outside rear-view mirrors p. 6-09

4. Locking and unlocking p. 3-15 Keyless entry system* p. 3-04 Keyless operation system* p. 3-08 Dead Lock System* p. 3-18

5. Side turn-signal lamps (on outside rear-view mirror)* p. 5-62, 10-25

6. Side turn-signal lamps (on fender)* p. 5-62, 10-25

7. Headlamps, high/low beam p. 5-55, 10-25

8. Position lamps/Daytime running lamps p. 5-55, 5-57, 10-25

9. Front turn-signal lamps p. 5-62, 10-25, 10-30

10. Front fog lamps p. 5-63, 10-25, 10-30

11. Headlamps, low beam p. 5-55, 10-25, 10-26

12. Headlamps, high-beam p. 5-55, 10-25, 10-26

13. Position lamps p. 5-55, 10-25, 10-29

14. Front turn-signal lamps p. 5-62, 10-25, 10-30

15. Daytime running lamps p. 5-57, 10-25, 10-30

16. Front fog lamps* p. 5-63, 10-25, 10-30

17. Headlamps, low beam p. 5-55, 10-25, 10-26

18. Headlamps, high-beam p. 5-55, 10-25, 10-26

19. Position lamps p. 5-55, 10-25, 10-29

20. Front turn-signal lamps p. 5-62, 10-25, 10-30

21. Front fog lamps* p. 5-63, 10-25, 10-30 Daytime running lamp p. 5-57, 10-25, 10-30

22. Ultrasonic misacceleration Mitigation System sensor* p. 6-100 Sensor system sensor* p. 6-119

23. Bonnet p. 10-03 Engine compartment p. 10-02, 11-15

24. Wiper and washers p. 5-64, 10-17

25. Sensor* [for Automatic High-Beam (AHB), Forward Collision Mitigation system (FCM) and Lane Departure Warning (LDW)] p. 5-58, 6-89, 6-112 Rain sensor* p. 5-65

26. Antenna p. 7-73

Exterior - front

1-10

OKTE20E1

Overview/Quick guide

Page 13

Exterior - rear

Club cab

1. Tyre inflation pressures p. 10-13 Changing tyres p. 8-16 Tyre rotation p. 10-15 Snow tyres p. 10-16 Snow traction device (Tyre chains) p. 10-16

2. Tail and stop lamps p. 5-55, 10-25

3. Rear turn-signal lamps p. 5-62, 10-25, 10-32

4. Reversing lamps p. 10-25, 10-32

5. Ultrasonic misacceleration Mitigation System sensor* p. 6-100 Reversing sensor system sensor* p. 6-119 Sensor system sensor* p. 6-119

6. Spare wheel p. 8-17

7. Licence plate lamps p. 5-52, 10-25, 10-33

8. Ultrasonic misacceleration Mitigation System sensor* p. 6-100 Reversing sensor system sensor* p. 6-119 Sensor system sensor* p. 6-119

9. Rear fog lamp (driver’s side)* p. 5-63, 10-25

10. Rear gate p. 3-20

11. Rear-view camera* p. 6-123

12. High-mounted stop lamp* p. 10-25

Exterior - rear

1-11

OKTE20E1

Overview/Quick guide

Page 14

Double cab

1. Tyre inflation pressures p. 10-13 Changing tyres p. 8-16 Tyre rotation p. 10-15 Snow tyres p. 10-16 Snow traction device (Tyre chains) p. 10-16

2. Tail and stop lamps p. 5-55, 10-25

3. Rear turn-signal lamps p. 5-62, 10-25, 10-32

4. Reversing lamps p. 10-25, 10-32

5. Ultrasonic misacceleration Mitigation System sensor* p. 6-100 Reversing sensor system sensor* p. 6-119 Sensor system sensor* p. 6-119

6. Spare wheel p. 8-17

7. Licence plate lamps p. 5-52, 10-25, 10-33

8. Ultrasonic misacceleration Mitigation System sensor* p. 6-100 Reversing sensor system sensor* p. 6-119 Sensor system sensor* p. 6-119

9. Rear gate p. 3-20

10. Rear fog lamp (driver’s side)* p. 5-63, 10-25

11. Rear-view camera* p. 6-123

12. High-mounted stop lamp* p. 10-25

13. Blind Spot Warning lamp* p. 6-106

Exterior - rear

1-12

OKTE20E1

Overview/Quick guide

Page 15

Quick guide

Locking and unlocking the doors

Keyless entry system*

Press the key switch, and all doors will be locked or unlocked as desired. It is also possible to operate the outside rearview mirrors. (Vehicles equipped with the mirror retractor switch) The key switch will operate within approximately 4 m from the vehicle.

Keyless entry key Keyless operation key

1. LOCK switch

2. UNLOCK switch

3. Indication lamp

Refer to “Keyless entry system*” on page 3-04.

For vehicles equipped with the mirror retractor switch, the outside rear-view mirrors can be retracted and extended automatically if you press the LOCK switch (1) or UNLOCK switch (2).

Refer to “Operation of the outside rearview mirrors” on page 3-05.

Keyless operation system*

When you are carrying the keyless operation key and within the operating range, if you press the driver’s or front passenger’s door switch (A), the doors are locked/unlocked. The operating range is approximately 70 cm from the driver’s or front passenger’s door lock/unlock switch.

Refer to “Keyless operation system*” on page 3-08.

Around the driver’s seat

Quick guide

1-13

OKTE20E1

Overview/Quick guide

Page 16

1-Electric remote-controlled outside rear-view mirrors*

To adjust the mirror position

Except for vehicles equipped with the mirror retractor switch

Vehicles equipped with the mirror retractor switch

L- Left outside mirror adjustment

R- Right outside mirror adjustment

1- Up

2- Down

3- Right

4- Left

5- Mirror retractor switch*

Refer to “Outside rear-view mirrors” on page 6-09.

2-Engine switch*

If you are carrying the keyless operation key, you can start the engine. If you press the engine switch without depressing the brake pedal (A/T) or the clutch pedal (M/T), you can change the operation mode in the order of OFF, ACC, ON, OFF.

OFF- The indication lamp on the en-

gine switch turns off.

ACC- The indication lamp on the en-

gine switch illuminates orange.

ON- The indication lamp on the en-

gine switch illuminates green.

Refer to “Engine switch” on page 6-13.

3-Combination headlamps

Rotate the switch to turn on the lamps.

Type 1

OFF All lamps off

Position, tail, licence plate and instrument panel lamps on

Headlamps and other lamps go on

Type 2

Quick guide

1-14

OKTE20E1

Overview/Quick guide

Page 17

OFF All lamps off

AUTO

With the ignition switch or the operation mode is in ON, headlamps, position, tail, licence plate and instrument panel lamps turn on and off automatically in accordance with outside light level. All lamps turn off automatically when the ignition switch is turned to “OFF” position or the operation mode is put in OFF.

Position, tail, licence plate and instrument panel lamps on

Headlamps and other lamps go on

Refer to “Combination headlamps and dipper switch” on page 5-55.

3-Turn-signal lever

The turn-signal lamps flash when the lever is operated.

1. Turn-signals

2. Lane-change signals

Refer to “Turn-signal lever” on page 5-62.

4-Steering wheel height and reach adjustment

1. Release the lever while holding the steering wheel up.

2. Adjust the steering wheel to the desired position.

3. Securely lock the steering wheel by pulling the lever fully upward.

A- Locked

B- Release

*: Vehicles equipped with the

reach adjustment

Refer to “Steering wheel height and reach adjustment” on page 6-07.

Quick guide

1-15

OKTE20E1

Overview/Quick guide

Page 18

5-Wiper and washer switch

Except for vehicles equipped with rain sensor

MIST- Misting function

The wipers will operate once.

OFF- Off

INT- Intermittent (Speed sensi-

tive)

LO- Slow

HI- Fast

Vehicles with rain sensor

MIST- Misting function

The wipers will operate once.

OFF- Off

AUTO- Auto-wiper control

Rain sensor The wipers will automatically operate depending on the degree of wetness on the windscreen.

LO- Slow

HI- Fast

The washer fluid will be sprayed onto the windscreen by pulling the lever towards you.

Refer to “Wiper and washer switch” on page 5-64.

6-Electric window control*

Press the switch down for opening the window, and pull the switch for closing.

Driver’s switch LHD

Driver’s switch RHD

1. Driver’s door window

2. Front passenger’s door window

3. Rear left door window (Double cab)

4. Rear right door window (Double cab)

5. Lock switch

Lock switch

If you press the switch (5), the passenger’s switches cannot be operated. To cancel, press it once again.

Refer to “Electric window control*” on page 3-21.

Quick guide

1-16

OKTE20E1

Overview/Quick guide

Page 19

7-Fuel tank filler door release lever*

Open the fuel tank filler door. The fuel tank filler is located on the rear left side of your vehicle.

Type 1

Type 2

Refer to “Filling the fuel tank” on page 2-03.

Automatic transmission Sports Mode 6A/T

Selector lever operation

The transmission selects an optimum gear automatically, depending on the speed of the vehicle and the position of the accelerator pedal.

LHD

RHD

While depressing the brake pedal, move the selector lever through the gate.

Move the selector lever through the gate.

Selector lever positions

“P” PARK

This position locks the transmission to prevent the vehicle from moving. The engine can be started in this position.

“R” REVERSE

This position is to back up.

“N” NEUTRAL

At this position the transmission is disengaged.

“D” DRIVE

This position is for normal driving.

Refer to “Automatic transmission Sports Mode 6A/T*” on page 6-31.

Quick guide

1-17

OKTE20E1

Overview/Quick guide

Page 20

4-wheel drive operation

Driving mode

Road conditions

Dry paved road

and highway

Packed snow road Gravel road

Deep snow or

muddy r

oad

Sandy road Rocky road

Easy Select 4WD

® p. 6-37

2H 4H 4H or 4L 4H or 4L 4H or 4L 4H or 4L

Super Select 4WD

II ® p. 6-46

2H or 4H 4H 4HLc or 4LLc 4HLc or 4LLc 4HLc or 4LLc 4HLc or 4LLc

Off Road mode-se-

lector

® p. 6-53

− − GRAVEL MUD/SNOW SAND ROCK

Rear differential

lock ® p. 6-54

− − −

Active

The Off Road mode and the rear differential lock cannot be used at the same time. When the rear differential lock is set to ON, the Off Road mode turns off. In addition, when the rear differential lock is ON, the Off Road mode will be deactivated even if the Off Road mode-selector is operated.

CAUTION

When

driving off-road, confirm the conditions of the road surface and the landscape, and drive after confirming that the components of the suspension and

the bottom of the front and rear bumper do not make contact with the road surface. (Refer to “Vehicle dimensions” on page 11-04.)

Multi information display

Always stop the vehicle in a safe place before operating. The

following information is included on the multi information display: odometer, tripmeter, average fuel consumption etc.

Quick guide

1-18

OKTE20E1

Overview/Quick guide

Page 21

Type 1

1. Off Road mode indicator display* ® p. 6-53

2. Drive mode indicator display* (Vehicles with Easy Select 4WD) ® p. 6-38 (Vehicles with Super Select 4WD II) ® p. 6-46

mark display ® p. 5-07

4. Forward Collision Mitigation system (FCM) OFF indicator display* ® p. 6-94 Ultrasonic misacceleration Mitigation System (UMS) OFF indicator display* ® p. 6-105

5. Lane Departure Warning (LDW) indicator display* ® p. 6-112

6. Information screen ® p. 5-05

7. Engine coolant temperature display ® p. 5-07

8. Odometer ® p. 5-08

9. Cruise control indicator display ® p. 6-80

10. Speed limiter indicator display* ® p. 6-85

11. “

” or “ ” mark indicator

® p. 5-06

12. Gearshift indicator display (vehicles with M/T) ® p. 6-29

13. Selector lever position indicator display (vehicles with A/T) ® p. 6-33

14. Fuel remaining display ® p. 5-07

15. Outside temperature display ® p. 5-08

16. Auto Stop & Go indicator display* ® p. 6-25 Auto Stop & Go OFF indicator display* ® p. 6-29

Refer to “Multi information display” on page 5-03.

Type 2

1- Engine coolant temperature display

® p. 5-20 2- Gearshift indicator ® p. 6-29 3- Fuel remaining display ® p. 5-21 4- Information display ® p. 5-18 5- Service reminder ® p. 5-21

Refer to “Multi information display” on page 5-17.

Quick guide

1-19

OKTE20E1

Overview/Quick guide

Page 22

OKTE20E1

Page 23

Fuel selection...................................................................................... 2-02

Filling the fuel tank.............................................................................2-03

Entering or leaving the vehicle*......................................................... 2-05

Installation of accessories................................................................... 2-05

Modification/alterations to the electrical or fuel systems................... 2-06

Genuine parts...................................................................................... 2-06

Safety and disposal information for used engine oil...........................2-06

Disposal information for used batteries.............................................. 2-07

Event Data Recording......................................................................... 2-07

General information

OKTE20E1

Page 24

Fuel selection

Recommended fuel

Cetane number (EN

590) 51 or higher

CAUTION

Your vehicle is designed to use only diesel fuel that meets the EN590 standard. Use of any other type of diesel fuel (bio diesel, methylester, etc.) would adversely affect the engine’s performance and durability.

If proper “winter” fuel is not used in winter, the diesel preheat indication lamp may blink and the engine speed may not rise above the idling speed because of fuel freezing. In this case, keep the engine idling for approximately 10 minutes, then turn off the ignition switch or put the operation mode in OFF and immediately turn it on or put in ON again to confirm that the diesel preheat indication lamp is off. (Refer to “Diesel preheat indication lamp” on page 5-50)

NOTE

For diesel fuel, due to the separation of paraffin, the fluidity of the fuel decreases considerably as the temperature falls. Because of this fact there are two kinds of fuel: “summer” and “winter”. This must be considered in winter use. Select either of the two kinds of fuel in accordance with ambient temperature.

Above -5 °C: “Summer” diesel

Below -5 °C: “Winter” diesel When travelling abroad, find out in advance about the fuels served in local service stations.

Poor-quality diesel fuel can cause deposits to form in the injector, resulting in black smoke and rough idling. If these problems occur, you are advised to add a cleaning additive to the diesel fuel when you refuel the vehicle. The additive will break up and remove the deposits, thereby returning the engine to a normal condition. Be sure to use a MITSUBISHI MOTORS GENUINE DIESEL FUEL SYSTEM CLEANER. Using an unsuitable additive could make the engine malfunction. For details, please contact your MITSUBISHI MOTORS Authorized Service Point.

Graphical expression for consumer information

B7: Diesel fuel containing up to 7.0 % (V/V) Fatty Acid Methyl Esters - Eg. EN 590 compliant diesel The diesel engine are compatible with B7 type diesel (containing 7 % fatty acid methyl esters) conforming to European standards EN590.

CAUTION

Do not use more than 7 % concentration of fatty acid methyl esters (bio diesel) by volume. Use of more than 7 % concentration would adversely affect the engine’s performance and durability.

Fuel selection

2-02

OKTE20E1

General information

Page 25

Filling the fuel tank

WARNING

When handling fuel, comply with the safety regulations displayed by garages and filling stations.

Fuel is highly flammable and explosive. You could be burned or seriously injured when handling it. When refueling your vehicle, always turn the engine off and keep away from flames, sparks and smoking materials. Always handle fuel in wellventilated outdoor areas.

Before removing the fuel cap, be sure to get rid of your body’s static electricity by touching a metal part of the vehicle or fuel pump. Any static electricity on your body could create a spark that ignites fuel vapour.

Perform the whole refueling process (opening the fuel tank filler door, removing the fuel cap, etc.) by yourself. Do not let any other person come near the fuel tank filler. If you allowed a person to help you and that person was carrying static electricity, fuel vapour could be ignited.

Do not move away from the fuel tank filler until refueling is finished. If you moved away and did something else (for example, sitting on a seat) part-way through the refueling process, you could pick up a fresh charge of static electricity.

Be careful not to inhale fuel vapour. Fuel contains toxic substances.

WARNING

Keep the doors and windows closed while refueling the vehicle. If they were open, fuel vapour could get into the cabin.

If the fuel cap must be replaced, use only a MITSUBISHI MOTORS genuine part.

Fuel tank capacity

75 litres

Refueling

1. Before filling with fuel, stop the engine.

2. The fuel tank filler is located on the rear left side of your vehicle. Open the fuel tank filler door with the release lever located below the instrument panel. (Only vehicles for Type 1,

Type 1

Type 2

3. [Vehicles for Type 1, 2] Open the fuel tank filler tube by slowly turning the fuel cap anticlockwise.

Type 1

Filling the fuel tank

2-03

OKTE20E1

General information

Page 26

Type 2

1- Remove 2- Close

[Vehicles for Type 3] Open the cover (1). Insert the key in the fuel cap (2) and unlock it. Turn the fuel cap and remove it.

Type 3

CAUTION

Since the fuel system may be under pressure, remove the fuel cap slowly. This relieves any pressure or vacuum that might have built up in the fuel tank. If you hear a hissing sound, wait until it stops before removing the fuel cap. Otherwise, fuel may spray out, injuring you or others.

NOTE

While filling with fuel, hang the fuel cap on the hook (A) located on the inside of the fuel tank filler door.

Type 1

NOTE

While filling with fuel, store the fuel cap in the cap holder located on the inside of the fuel tank filler door.

Type 2

4. Insert the gun in the tank port as far as it goes.

CAUTION

Do not tilt the gun.

5. When the gun stops automatically, do not fill with fuel any more.

Filling the fuel tank

2-04

OKTE20E1

General information

Page 27

6. [Vehicles for Type 1, 2] To close, turn the fuel cap slowly clockwise until you hear clicking sounds, then gently push the fuel tank filler door closed. [Vehicles for Type 3] To close, turn the fuel cap slowly clockwise until you hear clicking sounds, then turn the key clockwise to lock the fuel cap.

Entering or leaving the vehicle*

CAUTION

To avoid slipping and damaging the painted surface, do not step on the cover of the side step (A).

Installation of accessories

We recommend you to consult your MITSUBISHI MOTORS Authorized Service Point.

CAUTION

Your vehicle is equipped with a diagnosis connector for checking and servicing the electronic control system. Do not connect a device other than a diagnosis tool for inspections and service to this connector. Otherwise, the battery could be discharged, the electronic devices of the vehicle could malfunction, or other unexpected problems could result. In addition, malfunctions caused by connecting a device other than a diagnosis tool may not be covered under warranty.

The installation of accessories, optional parts, etc., should only be carried out within the limits prescribed by law in your country, and in accordance with the guidelines and warnings contained within the documents accompanying this vehicle.

Improper installation of electrical parts could cause fire, please refer to the Modification/ alteration to the electrical or fuel systems section within this owner’s manual.

When installing the radio, for the required information (frequency, transmission output, installing procedure), consult a MITSUBISHI MOTORS Authorized Service Point. If the frequency, transmission output and installing condition are not appropriate, it can adversely affect the electronic devices and could lead to unsafe vehicle operation.

Using a cellular phone or radio set inside the vehicle without an external antenna may cause electrical system interference, which could lead to unsafe vehicle operation.

Tyres and wheels which do not meet specifications must not be used. Refer to the “Specifications” section for information regarding wheel and tyre sizes.

Important points!

Due to a large number of accessories and replacement parts of different manufactures available in the market, it is not possible, not only for MITSUBISHI MOTORS, but also for a MITSUBISHI MOTORS Authorized Service Point, to check whether the attachment or installation of such parts affects the overall safety of your vehicle.

Entering or leaving the vehicle*

2-05

OKTE20E1

General information

Page 28

Even when such parts are officially Authorized, for example by a “general operators permit” (an appraisal for the part) or through the execution of the part in an officially approved manner of construction, or when a single operation permit following the attachment or installation of such parts, it cannot be deduced from that alone, that the driving safety of your vehicles has not been affected.

Consider also that there basically exists no liability on the part of the appraiser or the official. Maximum safety can only be ensured with parts recommended, sold and fitted or installed by a MITSUBISHI MOTORS Authorized Service Point (MITSUBISHI MOTORS GENUINE replacement parts and MITSUBISHI MOTORS accessories). The same also pertains to modifications of vehicles with respect to the production specifications. For safety reasons, do not attempt any modifications other than those that follow the recommendations of a MITSUBISHI MOTORS Authorized Service Point.

Modification/alterations to the electrical or fuel systems

MITSUBISHI MOTORS has always manufactured safe, high quality vehicles. In order to maintain this safety and quality, it is important that any accessory that is to be fitted, or any modifications carried out which involve the electrical or fuel systems, should be carried out in accordance with MITSUBISHI MOTORS guidelines.

CAUTION

If the wires interferes with the vehicle body or improper installation methods are used (protective fuses not included, etc.), electronic devices may be adversely affected, resulting in a fire or other accident.

Genuine parts

MITSUBISHI MOTORS has gone to great lengths to bring you a superbly crafted vehicle offering the highest quality and dependability.

Use MITSUBISHI MOTORS GENUINE Parts, designed and manufactured to maintain your MITSUBISHI MOTORS vehicle at top performance. MITSUBISHI MOTORS GENUINE Parts are identified by this mark and are available at all MITSUBISHI MOTORS Authorized Service Points.

Safety and disposal information for used engine oil

WARNING

Prolonged and repeated contact may cause serious skin disorders, including dermatitis and cancer.

Avoid contact with the skin as far as possible and wash thoroughly after any contact.

Keep used engine oils out of reach of children.

Modification/alterations to the electrical or fuel systems

2-06

OKTE20E1

General information

Page 29

Protect the environment

It is illegal to pollute drains, water courses and soil. Use authorized waste collection facilities, including civic amenity sites and garages providing facilities for disposal of used oil and used oil filters. If in doubt, contact your local authority for advice on disposal.

Disposal information for used batteries

Your vehicle contains batteries and/or accumulators. Do not mix with general household waste. For proper treatment, recovery and recycling of used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2006/66/EC. By disposing of these batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

Event Data Recording

This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.

The EDR in this vehicle is designed to record such data as:

How various systems in your vehicle were operating;

How far (if at all) the driver was depressing the accelerator and/or brake pedal; and,

How fast the vehicle was traveling.

These data can help provide a better understanding of the circumstances in which crashes and injuries occur.

NOTE

EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.

To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.

Disposal information for used batteries

2-07

OKTE20E1

General information

Page 30

OKTE20E1

Page 31

Keys.................................................................................................... 3-02

Key number tag...................................................................................3-02

Electronic immobilizer (Anti-theft starting system)........................... 3-03

Keyless entry system*.........................................................................3-04

Keyless operation system*..................................................................3-08

Doors...................................................................................................3-15

Central door locks............................................................................... 3-17

Dead Lock System*............................................................................ 3-18

“Child-protection” rear doors (Double cab)........................................3-19

Rear gate............................................................................................. 3-20

Manual window control*.................................................................... 3-21

Electric window control*.................................................................... 3-21

Locking and unlocking

OKTE20E1

Page 32

Keys

Key

Keyless operation key

Keyless entry key

1. Master key

2. Keyless entry key

3. Keyless operation key

4. Emergency key

WARNING

When taking a key on flights, do not press any switches on the key while on the plane. If a switch is pressed on the plane, the key emits electromagnetic waves, which could adversely affect the plane’s flight operation. When carrying a key in a bag, be careful that no switches on the key can be easily pressed by mistake.

NOTE

The key (except for the emergency key) is a precision electronic part with a built-in signal transmitter. Please observe the following in order to prevent a malfunction.

•

Do not leave in a place that is exposed to direct sunlight, for example on the dashboard.

•

Do not disassemble or modify.

•

Do not excessively bend the key or subject it to strong impacts.

•

Do not expose to water.

•

Keep away from magnetic key rings.

•

Keep away from audio systems, personal computers, TVs, and other equipment that generates a magnetic field.

•

Keep away from devices that emit strong electromagnetic waves, such as cellular phones, wireless devices and high frequency equipment (including medical devices).

NOTE

•

Do not clean with ultrasonic cleaners or similar equipment.

•

Do not leave the key where it may be exposed to high temperature or high humidity.

The engine is designed so that it will not start if the ID code registered in the immobilizer computer and the key’s ID code do not match. Refer to the “Electronic immobilizer” section for details and key usage.

If you lose one of them, contact a MITSUBISHI MOTORS Authorized Service Point as soon as possible to prevent theft.

Key number tag

The key number is stamped on the tag as indicated in the illustration.

Keys

3-02

OKTE20E1

Locking and unlocking

Page 33

Make a record of the key number and store the key and key number tag in separate places, so that you can order a key from your MITSUBISHI MOTORS Authorized Service Point in the event the original keys are lost.

Electronic immobilizer (Anti-theft starting system)

CAUTION

Don’t make any alterations or additions to the immobilizer system; alterations or additions could cause failure of the immobilizer.

The electronic immobilizer has been designed to significantly reduce the possibility of vehicle theft. The purpose of the system is to immobilize the vehicle if an invalid start is attempted. A valid start attempt can only be achieved by using a key “registered” to the immobilizer system.

NOTE

[Vehicles without keyless operation system] In the following cases, the vehicle may not be able to receive the registered ID code from the registered key and engine may not start.

•

When the key contacts a key ring or other metallic or magnetic object

•

When the key grip contacts metal of another key

NOTE

•

When the key contacts or is close to other immobilizing keys (including keys of other vehicles)

In cases like these, remove the object or additional key from the vehicle key. Then try again to start the engine. If the engine does not start, we recommend you to con-

Electronic immobilizer (Anti-theft starting system)

3-03

OKTE20E1

Locking and unlocking

Page 34

NOTE

tact a MITSUBISHI MOTORS Authorized Service Point.

[Vehicles equipped with keyless operation system] If the engine does not start, we recommend you to contact a MITSUBISHI MOTORS Authorized Service Point.

If you lose one of the master keys, the keyless entry keys or the keyless operation keys, contact a MITSUBISHI MOTORS Authorized Service Point as soon as possible. Refer to “Keys” on page 3-02. To obtain a key, take your vehicle and all remaining keys to a MITSUBISHI MOTORS Authorized Service Point. If you need an extra spare key, take your vehicle and all the keys to a MITSUBISHI MOTORS Authorized Service Point. All the keys have to be re-registered in the immobilizer computer unit. For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.

NOTE

[Vehicles equipped with keyless operation system] When the electronic immobilizer is abnormal, the warning display will appear. Put the operation mode in OFF and then start the engine again. If the warning is not cancelled, contact a MITSUBISHI MOTORS Authorized Service Point.

Keyless entry system*

Press the key switch, and all doors will be locked or unlocked as desired.

It is also possible to operate the outside rearview mirrors. (Vehicles equipped with the mirror retractor switch)

Keyless entry key Keyless operation key

1. LOCK switch

2. UNLOCK switch

3. Indication lamp

To lock

Press the LOCK switch (1). All the doors will be locked. The turn-signal lamps will blink once. When they are locked with the room lamp switch in the middle (•) position, the room lamp also blinks once.

Keyless entry system*

3-04

OKTE20E1

Locking and unlocking

Page 35

To unlock

Press the UNLOCK switch (2). All the doors will be unlocked. If the room lamp switch is in the middle (•) position at this time, the room lamp will come on for approximately 15 seconds and the turn-signal lamps will blink twice.

NOTE

For vehicles equipped with the mirror retractor switch, the outside rear-view mirrors automatically retract or extend when all the doors are locked or unlocked using the key switches of the keyless entry system. Refer to “Starting and driving: Outside rear-view mirrors” on page 6-09.

If the UNLOCK switch (2) is pressed and no door is opened within approximately 30 seconds, relocking will automatically occur.

It is possible to modify functions as follows: For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.

•

The time from pressing the UNLOCK switch (2) to the moment of automatic locking can be changed.

•

Activating the operation confirmation function (blinking of the turn-signal lamps) only during locking, or only during unlocking.

•

The confirmation function (this indicates locking or unlocking of the doors with the blink of the turn-signal lamps) can be deactivated.

NOTE

•

The number of times the turn-signal lamps are flashed by the confirmation function can be changed.

The keyless entry system does not operate in the following conditions:

•

The key is left in the ignition switch. (except for vehicles with keyless operation system)

•

The operation mode is not in OFF. (vehicles with keyless operation system)

•

The door is open.

The key switch will operate within approximately 4 m from the vehicle. However, the operating range of the key switch may change if the vehicle is located near a TV transmitting tower, power station, or radio broadcasting station.

If either of the following problems occurs, the battery may be exhausted.

•

The key switch is operated at the correct distance from the vehicle, but the doors are not locked/unlocked in response.

•

The indication lamp (3) is dim or does not come on.

For further information, please contact a MITSUBISHI MOTORS Authorized Service Point. If you replace the battery yourself, refer to “Procedure for replacing the key battery” on page 3-06.

If your key is lost or damaged, please contact a MITSUBISHI MOTORS Authorized Service Point for a replacement key.

NOTE

If you wish to add key, please contact a MITSUBISHI MOTORS Authorized Service Point. The following numbers of the keys are available.

•

Keyless entry key: up to 4 keys.

•

Keyless operation key: up to 4 keys.

Operation of the Dead Lock System*

With a vehicle that has a Dead Lock System, it is possible to set the Dead Lock System by pressing the LOCK switch (1) two times. Refer to “Dead Lock System*” on page 3-18 for details.

Operation of the outside rearview mirrors (Vehicles equipped with mirror retractor switch)

To retract

Locking the doors using the LOCK switch (1), the outside rear-view mirrors are retracted automatically.

Keyless entry system*

3-05

OKTE20E1

Locking and unlocking

Page 36

To extend

Unlocking the doors using the UNLOCK switch (2), the outside rear-view mirrors are extended automatically.

NOTE

Functions can be modified as stated below. Please consult a MITSUBISHI MOTORS Authorized Service Point.

•

Automatically extend when the driver’s door is closed, and then the following operation is performed. [Except vehicles equipped with keyless operation system] Turn the ignition switch to the “ON” position. [Vehicles equipped with keyless operation system] Put the operation mode in ON.

•

Automatically retract when the ignition switch is turned to the “LOCK” or “ACC” position or the operation mode is put in OFF or ACC, and the driver’s door is then opened.

•

Automatically extend when the vehicle speed reaches approximately 30 km/h.

NOTE

•

Deactivate the automatic extension function.

The outside rear-view mirrors can be retracted or extended by the following operations, even if changing to any of the above. After pressing the “LOCK” switch to lock the doors, if the “LOCK” switch is pressed again twice in a row within approximately 30 seconds, the outside rear-view mirrors will retract. After pressing the “UNLOCK” switch to unlock the doors, if the “UNLOCK” switch is pressed again twice in a row within approximately 30 seconds, the outside rearview mirrors will extend again.

Procedure for replacing the key battery

Before replacing the battery, remove static electricity from your body by touching a metal grounded object.

WARNING

Do not swallow a coin type battery.

WARNING

•

This product contains a coin type battery. If a coin type battery is swallowed, it can cause severe internal burns and can lead to death. There have been cases where a swallowed battery has caused severe internal burns in just 2 hours.

•

Keep new and used batteries away from children.

•

If the key case does not close securely, stop using the product and keep it away from children.

•

If you think batteries might have been swallowed or placed inside any part of a person’s body, seek immediate medical attention.

To prevent that can result in an explosion or the leakage of flammable liquid or gas.

•

Do not replace an incorrectly battery. Replace only with the same battery or an equivalent type.

•

Do not dispose of a battery into fire or incinerator, or mechanically crushing or cutting of a battery.

•

Do not use, store in or bring into a battery where it may be exposed to extremely high temperature or extremely low air pressure.

CAUTION

When the key case is opened, be careful to keep water, dust, etc. out. Also, do not touch the internal components.

Keyless entry system*

3-06

OKTE20E1

Locking and unlocking

Page 37

CAUTION

Dispose of used batteries according to regulations for the disposal of battery.

NOTE

You may purchase a replacement battery at an electric appliance store.

A MITSUBISHI MOTORS Authorized Service Point can replace the battery for you if you prefer.

1. Remove the screw (A) from the key. (Keyless entry key only)

Keyless entry key

2. Remove the emergency key from the key. (Keyless operation key only) Refer to “Emergency key” on page 3-11.

3. With the MITSUBISHI mark facing you, insert the cloth-covered tip of a straight

blade (or minus) screwdriver into the notch in the key case and use it to open the case.

Keyless entry key

Keyless operation key

NOTE

Be sure to perform the procedure with the MITSUBISHI mark facing you. If the MITSUBISHI mark is not facing you when you open the key case, the switches may come out.

4. Remove the used battery.

5. Install a new battery with the + side (B) up.

Keyless entry key

+ side

- side

Coin type battery CR1620

Keyless operation key

+ side

- side

Coin type battery CR2032

6. Close the key case firmly.

7. Attach the screw (A) removed in step 1. (Keyless entry key only)

8. Install the emergency key removed in step 2. (Keyless operation key only)

Keyless entry system*

3-07

OKTE20E1

Locking and unlocking

Page 38

9. Check the keyless entry system to see that it works.

Keyless operation system*

The keyless operation system allows you to lock and unlock the doors, start the engine and change the operation mode simply by carrying the keyless operation key with you. The switches on the keyless operation key can also be used as the key switch of keyless entry system. Refer to “Starting and stopping the engine” on page 6-17. Refer to “Keyless entry system*” on page 3-04.

The driver should always carry the keyless operation key. This key is necessary for locking and unlocking the doors, starting the engine and otherwise operating the vehicle, so before locking and leaving the vehicle, be sure to check that you have the keyless operation key.

WARNING

People with implantable cardiac pacemakers or implantable cardiovascular-defibrillators should not go near the exterior transmitters (A) or the interior transmitters (B). The radio waves used by the keyless operation system could adversely affect implantable cardiac pacemakers or implantable cardiovascular-defibrillators.

Club cab

Double cab

WARNING

When using electro-medical devices other than implantable cardiac pacemakers or implantable cardiovascular-defibrillators, contact the electro-medical device manufacturer ahead of time to determine the affects of radio waves on the devices. Electro-medical device operations could be affected by radio waves.

You can limit the possible operations of the keyless operation system in the following ways. (The keyless operation system can be used as a keyless entry system.) Please consult a MITSUBISHI MOTORS Authorized Service Point.

You can limit operations to locking and unlocking the doors.

Keyless operation system*

3-08

OKTE20E1

Locking and unlocking

Page 39

You can limit operations to starting the engine.

The keyless operation system can be disabled.

NOTE

The keyless operation key uses an ultraweak electromagnetic wave. In the following cases, the keyless operation system may not operate properly or may be unstable.

•

When there is equipment nearby that emits strong radio waves, such as: a power station, a radio/TV broadcasting station or an airport.

•

The keyless operation system is carried together with a communications device such as a cellular phone or radio set, or with an electronic device such as a personal computer.

•

The keyless operation key is touching or covered by a metal object.

•

A keyless entry system is being used nearby.

•

When the keyless operation key battery is worn out.

•

When the keyless operation key is placed in an area with strong radio waves or noise. In such cases, use the emergency key. Refer to “To lock/unlock without using the keyless operation function” on page 3-11.

NOTE

Because the keyless operation key receives signals in order to communicate with the transmitters in the vehicle, the battery continually wears down regardless of keyless operation key use. The battery life is 1 to 2 years, depending on usage conditions. When the battery wears out, replace the battery according to the description in this manual or have it replaced a MITSUBISHI MOTORS Authorized Service Point. Refer to “Procedure for replacing the key battery” on page 3-06.

Because the keyless operation key continually receives signals, strong radio wave reception could affect battery wear. Do not leave the key near a TV, personal computer, or other electronic device.

Operating range of the keyless operation system

If you are carrying the keyless operation key, enter the operating range of the keyless operation system, and press the driver’s or front passenger’s door lock/unlock switch, the ID code for your key is verified. You can lock and unlock the doors, start the engine and change the operation mode only if the ID codes of your keyless operation key and the vehicle match.

NOTE

If the keyless operation key battery is wearing out or there are strong electromagnetic waves or noise present, the operating range may become smaller and operation may become unstable.

Operating range for locking and unlocking the doors

The operating range is approximately 70 cm from the driver’s or front passenger’s door lock/unlock switch.

* : Forward direction

: Operating range

Keyless operation system*

3-09

OKTE20E1

Locking and unlocking

Page 40

NOTE

Locking and unlocking operates only when you press a door switch that detects the keyless operation key.

Operation may not be possible if you are too close to the front door, door window.

Even if the keyless operation key is within 70 cm of the driver’s or front passenger’s door lock/unlock switch, if the key is near to the ground or high up, the system may not operate.

If the keyless operation key is within the operating range, even someone not carrying the key can lock and unlock the doors by pressing the driver’s or front passenger’s door lock/unlock switch.

Operating range for starting the engine and changing the operation mode

The operating range is the interior of the vehicle.

*: Forward direction

Operating range

NOTE

Even if it is within the operating range, if the keyless operation key is in a small item holder such as the glove box, on top of the instrument panel, door pocket or in the luggage compartment, it may be impossible to start the engine and change the operation mode.

NOTE

If a keyless operation key is too close to the door or door window, it may be possible to start the engine or change the operation mode even when the key is outside the vehicle.

To operate using the keyless operation function

Locking the doors

When you are carrying the keyless operation key, if you press the driver’s or front passenger’s door lock/unlock switch (A), within the operating range, the doors are locked. The turn-signal lamps will blink once. Also refer to “Locking and unlocking: Doors, Central door locks” on pages 3-15, and 3-17.

Keyless operation system*

3-10

OKTE20E1

Locking and unlocking

Page 41

Unlocking the doors

When you are carrying the keyless operation key, if you press the driver’s or front passenger’s door lock/unlock switch (A), within the operating range, all the doors are unlocked. If the room lamp switch is in the middle (•) position at this time, the room lamp will turn on for 15 seconds. The turn-signal lamps will blink twice. If the driver’s or front passenger’s door lock/ unlock switch is pressed and any of the doors is not opened within approximately 30 seconds, relocking will automatically occur. Refer to “Locking and unlocking: Doors, Central door locks” on pages 3-15, and 3-17.

NOTE

For vehicles equipped with the mirror retractor switch, the outside rear-view mirrors automatically retract/extend when all the doors are locked/unlocked using the keyless operation function. Refer to “Starting and driving: Outside rear-view mirrors” on page 6-09.

For vehicles equipped with the Dead Lock System, pressing the driver’s or front passenger’s door lock/unlock switch (A) two times in succession causes the Dead Lock System to be set. (Refer to “Setting the system” on page 3-18.)

The keyless operation function does not operate under the following conditions:

NOTE

•

The keyless operation key is inside the vehicle.

•

A door is open or ajar.

•

The operation mode is not in OFF.

The time between unlocking and automatic locking can be adjusted. Please consult a MITSUBISHI MOTORS Authorized Service Point.

Operation confirmation when locking and unlocking

Operation can be confirmed as shown below. However, the room lamp will illuminate only if the room lamp switch is in the middle (•) position.

When locking: The turn-signal

lamps will blink once.

When unlocking: The room lamp illu-

minates for approximately 15 seconds, the turn-signal lamps blink twice.

NOTE

Functions can be modified as stated below. For further information, please contact a

NOTE

MITSUBISHI MOTORS Authorized Service Point.

•

Activating the operation confirmation function (blinking of the turn-signal lamps) only during locking, or only during unlocking.

•

Disabling the operation confirmation function (blinking of the turn-signal lamps).

•

Changing the number of blinks for the operation confirmation function (blinking of the turn-signal lamps).

To lock/unlock without using the keyless operation function

Emergency key

The emergency key (A) can only be used to lock and unlock the door. To use the emergency key, unlock the lock knob (B) and remove it from the keyless operation key (C).

Keyless operation system*

3-11

OKTE20E1

Locking and unlocking

Page 42

NOTE

Only use the emergency key for emergencies. If the keyless operation key battery wears out, replace it as quickly as possible so that you can use the keyless operation key.

The emergency key is built in the keyless operation key.

After using the emergency key, always return it into the original position.

Locking and unlocking the door

Turning the emergency key in the forward direction locks the door, and turning it in the rear direction unlocks the door. Also refer to “Locking and unlocking: Doors” on page 3-15.

1- Lock 2- Unlock

Operation of the Dead Lock System

For vehicles equipped with the Dead Lock System, it is possible to set the Dead Lock System using the driver’s or front passenger’s door lock/unlock switch. (Refer to “Dead Lock System*” on page 3-18.)

Keyless operation system*

3-12

OKTE20E1

Locking and unlocking

Page 43

Warning activation

In order to prevent vehicle theft or the accidental operation of the keyless operation system, the buzzer and the display on the information screen in the multi information display are used to alert the driver. If a warning is activated, always check the vehicle and the keyless operation key. The warning is also displayed if there is a fault in the keyless operation system.

Item Display Buzzer Note (Solution)

Detection of failure Inner buzzer sounds once There is a fault in the keyless operation system.

Fall of battery voltage Inner buzzer sounds once The battery starts to run out, the warning is activated. (The warning is

not activated if the battery is completely dead.)

Key not detected Inner buzzer sounds once When the engine switch is turned to the ACC or ON from OFF or when

the engine is started, the warning is activated, if any of the following conditions is occurred.

Carrying another keyless operation key with a different code, or the keyless operation key could be outside the operating range.

The battery of the keyless operation key is dead.

Communication is blocked by electric wave environment.

Keyless operation key reminder

Inner buzzer sounds approximately 1 minute Outer buzzer sounds approximately 3 seconds intermittently

If the operation mode is in OFF and the driver’s door is opened with the keyless operation key in the key slot, a warning is issued and the outer buzzer sounds for approximately 3 seconds and the inner buzzer sounds for approximately 1 minute to remind you to remove the key. If the key removed from key slot, the buzzer is stopped.

Keyless operation system*

3-13

OKTE20E1

Locking and unlocking

Page 44

Item Display Buzzer Note (Solution)

Keyless operation key takeout monitoring system

Inner buzzer sounds once Outer buzzer sounds intermittently

When the vehicle is parked with the operation mode in any mode other than OFF, if you close the door after opening any of the doors and taking the keyless operation key out of the vehicle, a warning is issued until the key is detected in the vehicle.

If you take the keyless operation key out of the vehicle through a window without opening a door, the keyless operation key take-out monitoring system does not operate.

It is possible to change the setting to make the keyless operation key take-out monitoring system operate if you take the keyless operation key out from the vehicle through a window without opening a door. For further information, please contact a MITSUBISHI MOTORS Authorized Service Point.

Even if you have the keyless operation key within the engine start operating range, if the keyless operation key and vehicle ID codes cannot be matched, for example due to the ambient environment or electromagnetic conditions, the warning may be activated.

Key lock-in prevention system

Inner buzzer sounds once Outer buzzer sounds approximately 3 seconds intermittently

When the operation mode is in OFF, if you close all the doors with the keyless operation key left in the vehicle and you try to lock the doors by pressing the driver’s or front passenger’s door lock/unlock switch, a warning is issued and you cannot lock the doors.

Make sure you have the keyless operation key with you before locking the doors. Even if you leave the keyless operation key inside the vehicle, it is possible that the doors will lock depending on the surrounding environment and wireless signal conditions.

Door ajar prevention system

Inner buzzer sounds once Outer buzzer sounds approximately 3 seconds intermittently

When the operation mode in OFF, if you try to lock the doors by pressing the driver’s or front passenger’s door lock/unlock switch, with one of the doors not completely closed, a warning is issued and you cannot lock the doors.

Keyless operation system*

3-14

OKTE20E1

Locking and unlocking

Page 45

Item Display Buzzer Note (Solution)

Operation mode OFF reminder system

Inner buzzer sounds once Outer buzzer sounds approximately 3 seconds intermittently

When the operation mode is in any mode other than OFF, if you try to lock the doors by pressing the driver’s or front passenger’s door lock/ unlock switch, a warning is issued and you cannot lock the doors.

Doors

CAUTION

Make sure the doors are closed: driving with doors not completely closed is dangerous.

Never leave children in the vehicle unattended.

Be careful not to lock the doors while the key is inside the vehicle.

NOTE

To prevent the key from being locked inside the vehicle, neither the lock knob on the driver’s door nor the key can be used to lock the driver’s door when it is open.

To lock or unlock with the key

1- Lock 2- Unlock

NOTE

On vehicles with central door locks, when locking or unlocking with the key, all doors will be locked or unlocked. Refer to “Central door locks” on page 3-17.

NOTE

If the vehicle is equipped with the keyless operation system, the driver’s door can be locked or unlocked with the emergency key. Refer to “Emergency key” on page 3-11.

To lock or unlock from inside the vehicle

1- Lock 2- Unlock

Doors

3-15

OKTE20E1

Locking and unlocking

Page 46

NOTE

The driver’s door can be opened without using the lock knob by pulling on the inside door handle. On vehicles with central door locks, all other doors are unlocked at the same time.

In a vehicle that has a Dead Lock System, it is not possible to unlock the door by pushing the lock knob to the unlock side while the Dead Lock System is set. (Refer to “Dead Lock System*” on page 3-18.)

To lock without using the key

Set the inside lock knob (1) to the locked position, and close the door (2).

NOTE

The driver’s door cannot be locked using the inside lock knob while the driver’s door is opened.

To open or close the rear door (Club cab)

You can open or close the rear door while the front door is opened.

1. Open the front door wide.

2. Pull the door handle (A) of the rear door.

3. Open the rear door.

4. When closing these doors, close the front door after closing the rear door.

WARNING

When opening the rear door, confirm that the occupant of the front seat has taken off the seat belt before opening the rear door. If you open the rear door with the front seat belt being worn, the occupant of the front seat may be tightened with the locked seat belt and could result in serious injury.

When closing the rear door, make sure not being trapped your hands or your fingers in the doors.

Before driving, make sure that the rear door is securely closed. If a door is ajar, the door ajar warning lamp will illuminates. If a door is not completely closed, the rear door could open while driving and this could cause an accident such as occupants being thrown from the vehicle.

CAUTION

When opening or closing the rear door, please observe the followings. If you do not follow them, it could result in damage to your vehicle.

•

Do not open or close the rear door when the front door is not completely opened.

•

Do not open or close the rear door and the front door at the same time.

•

Do not close the rear door after closing the front door.

Doors

3-16

OKTE20E1

Locking and unlocking

Page 47

Central door locks

NOTE

Repeated continuous operation between lock and unlock could activate the central door locking systems built-in protection circuit and prevent the system from operating. If this occurs, wait approximately 1 minute before operating the central door lock system.

All of the doors can be locked and unlocked as described hereafter.

Driver’s door with key

Using the key on the driver’s door locks or unlocks.

1. Lock

2. Unlock

NOTE

If the vehicle is equipped with the keyless operation system, the driver’s door can be locked or unlocked with the emergency key. Refer to “Emergency key” on page 3-11

Driver’s door with inside lock knob

Using the door lock knob on the driver’s door locks or unlocks all doors.

1. Lock

2. Unlock

NOTE

Be careful not to lock the doors while the key is inside the vehicle when getting off the vehicle.

Vehicle-speed sensitive automatic door lock (with impactsensitive unlock mechanism)

All of the doors lock automatically when the vehicle speed exceeds approximately 15 km/h (9 mph). In addition, all of the doors unlock when a strong impact that could be very dangerous to the occupants is sustained by the collision of the vehicle. This is prepared for rescue activities when an unexpected accident occurs.

WARNING

When the vehicle-speed sensitive automatic door lock/impact-sensitive unlock mechanism may not operate in the following conditions, have the vehicle inspected at a MITSUBISHI MOTORS Authorized Service Point immediately.

•

The door does not lock automatically even when the vehicle speed exceeds approximately 15 km/h (9 mph).

•

The door unlocks automatically while driving.

•

Even when the ignition switch or the operation mode is in ON, the SRS warning lamp does not come on or it remains on.

•

The SRS warning lamp comes on while driving.

•

The central door lock system is broken down.

Central door locks

3-17

OKTE20E1

Locking and unlocking

Page 48

NOTE

Even if the vehicle suffers significant deformation from a collision etc., depending on the location and angle of the collision, as well as on the shape and condition of the other object in the collision, the doors may not unlock. The extent of deformation or damage to the vehicle does not necessarily correlate with unlocking of the doors.

These functions are activated when the vehicle is shipped from the factory. If you wish to activate or deactivate these functions, please contact a MITSUBISHI MOTORS Authorized Service Point.

Unlocking by using the ignition switch, the engine switch or the selector lever

It is possible to unlock all of the doors whenever as follows. [Vehicles with M/T] The ignition switch is turned to the “LOCK” position or the operation mode is put in OFF. [Vehicles with A/T] The selector lever is placed in the “P” (PARK) position while the operation mode is in ON. Or the operation mode is put in OFF.

These functions are deactivated when the vehicle is shipped from the factory. If you wish to activate or deactivate these functions, please contact a MITSUBISHI MOTORS Authorized Service Point.

Dead Lock System*

The Dead Lock System helps prevent theft. When the keyless entry system or the keyless operation function has been used to lock all of the doors, the Dead Lock System makes it impossible to unlock the doors using the inside lock knobs.

CAUTION

Do not set the Dead Lock System when someone is inside the vehicle. With the Dead Lock System set, it is not possible to unlock the doors using the inside lock knobs. If you erroneously set the Dead Lock System, unlock the doors using the UNLOCK switch on the key or using the keyless operation function.

Setting the system

1. Turn the ignition switch to the “LOCK” position and then remove the key (vehicles with keyless entry system), or put the operation mode in OFF (vehicles with keyless operation system).

2. Get out of the vehicle. Close all of the doors.

3. Press the LOCK switch (A) on the key, the driver’s or front passenger’s door lock/unlock switch (C) to lock all of the doors. The turn-signal lamps will blink once.

4. Press the switch again within 2 seconds. The turn-signal lamps will blink three times to show that the Dead Lock System has been set.

Keyless entry system Keyless operation

system

Dead Lock System*

3-18

OKTE20E1

Locking and unlocking

Page 49

NOTE

Pressing the LOCK switch (A) on the key once while the Dead Lock System is set causes the turn-signal lamps to blink three times, so it is possible to confirm that the Dead Lock System is set.

Cancelling the system

When the following operation is performed, the doors will unlock and the Dead Lock System will be simultaneously cancelled.

The UNLOCK switch (B) on the key is pressed.

The driver’s or front passenger’s door lock/unlock switch (C) is pressed while you are carrying the keyless operation key.

NOTE

If a door is not opened within 30 seconds of unlocking, the doors are automatically relocked and the Dead Lock System is simultaneously set again.

Even when it is not possible to use the keyless entry system or keyless operation function to unlock the doors, it is possible to use the key to unlock the driver’s door. When the key is used to unlock the driver’s door, the Dead Lock System is cancelled for only the driver’s door. If you wish to subsequently unlock all other doors, turn the ignition switch to the “ON” or “ACC” position, or put the operation mode in ON or ACC.

It is possible to adjust the time between pressing the UNLOCK switch (B) on the key or the driver’s or front passenger’s door lock/unlock switch (C) and automatic locking. For details, please contact a MITSUBISHI MOTORS Authorized Service Point.

It is possible to lock the doors and set the Dead Lock System at the same time with a single push of the LOCK switch (A) on the key, the driver’s or front passenger’s door lock/unlock switch (C). For details, please contact a MITSUBISHI MOTORS Authorized Service Point.

Testing the system

Open all of the door windows, then set the Dead Lock System. (Refer to “Setting the system” on page 3-18.)

After setting the Dead Lock System, reach into the vehicle through a window and confirm that you cannot unlock the doors using the lock knobs.

NOTE

If you need advice on how to set the Dead Lock System, please contact a MITSUBISHI MOTORS Authorized Service Point.

“Child-protection” rear doors (Double cab)

1- Lock 2- Unlock

Child protection helps prevent doors from being opened accidentally, especially when small children are in the rear seat. A lever is provided on each rear door.

“Child-protection” rear doors (Double cab)

3-19

OKTE20E1

Locking and unlocking

Page 50

If the lever is set to the locked position, the rear door cannot be opened using the inside handle. To open the rear door while the child protection is in use, pull the outside door handle. If the lever is set to the “Unlock” position, the child protection mechanism does not function.

CAUTION

When driving with a child in the rear seat, please use the child protection to prevent accidental door opening which may cause an accident.

Rear gate

CAUTION

Do not stand behind the exhaust pipe when loading and unloading luggage. Heat from the exhaust could lead to burns.

Pay attention not to catch your fingers in the rear gate.

Do not weight the rear gate.

Before driving, make sure that the rear gate is securely closed. If the rear gate opens while driving the vehicle, objects stored in the cargo area could fall out onto the road.

To open

Lift up the handle and lower the rear gate.

To close

Raise the rear gate and close with enough force to latch the assembly securely into position.

To swing down

The rear gate can be swung down in two stages except some models. To lower it to the second stage, proceed as follows:

CAUTION

On vehicles with the rear bumper, never swing down the rear gate because the rear gate could be damaged.

1. Swing open the rear gate to the first position. Then, lift it up to the position shown in the illustration while holding the wire (A).

Rear gate

3-20

OKTE20E1

Locking and unlocking

Page 51

2. Remove the wire (A) on one side while aligning the hole in the wire with the hook (B).

3. Remove the wire on the other side in the same manner, and have the rear gate swing down slowly.

CAUTION

Never close the rear gate with the wire left unhooked.

Manual window control*

1- To open 2- To close

Electric window control*

The electric windows can only be operated with the ignition switch or the operation mode in ON.

Electric window control switch

Each door window opens or closes while the corresponding switch is operated.

Driver’s switch LHD

Driver’s switch RHD

1- Driver’s door window 2- Front passenger’s door window 3- Rear left door window (Double cab) 4- Rear right door window (Double cab) 5- Lock switch

WARNING

Before operating the electric window control, make sure that nothing can get trapped (head, hand, finger, etc.).

Never leave the vehicle without removing the key.

Never leave a child (or other person who might not be capable of safe operation of the electric window control) in the vehicle alone.

Manual window control*

3-21

OKTE20E1

Locking and unlocking

Page 52

WARNING

The child may tamper with the switch at the risk of its hands or head being trapped in the window.

Driver’s switches

The driver’s switches can be used to operate all door windows. A window can be opened or closed by operating the corresponding switch. Press the switch down to open the window, and pull up the switch to close it. If the switch for the driver’s window is fully pressed down/pulled up, the door window automatically opens/closes completely. If you want to stop the window movement, operate the switch lightly in the reverse direction.

Passenger’s switches

The passenger’s switches can be used to operate the corresponding passenger’s door windows.

Press the switch down for opening the window, and pull up the switch for closing it.

NOTE

Repeated operation with the engine stopped will run down the battery. Operate the window switches only while the engine is running.

The rear door windows only open halfway.

Lock switch

When this switch is operated, the passenger’s switches cannot be used to open or close the door windows and the driver’s switch cannot open or close any door windows other than the driver’s door window.

To unlock, press it once again.

1- Lock 2- Unlock

WARNING

A child may tamper with the switch at the risk of its hands or head being trapped in the window. When driving with a child in the vehicle, please press the window lock switch to disable the passenger’s switches.

Timer function

The door windows can be opened or closed for 30 seconds after the engine is stopped. However, once the driver’s door or the front passenger’s door is opened, the windows cannot be operated.

Electric window control*

3-22

OKTE20E1

Locking and unlocking

Page 53

Safety mechanism (driver’s window only)

When the door window is automatically closed by pulling up the switch fully, if a hand or head is trapped in the closing window, it will lower automatically. Nonetheless, make sure that nobody puts their head or hand out of the window when closing the driver’s door window. The lowered window will become operational after a few seconds.

WARNING

If the battery terminals are disconnected or the fuse for electric window is replaced, the safety mechanism will be cancelled. If a hand or head got trapped, a serious injury could result.

CAUTION

The safety mechanism is cancelled just before the window is fully closed. This allows the window to close completely. Therefore be especially careful that no fingers are trapped in the window.

The safety mechanism is deactivated while the switch is pulled up. Therefore be especially careful that fingers are not trapped in the door window opening.

NOTE

The safety mechanism can be activated if the driving conditions or other circumstances cause the driver’s door window to be subjected to a physical shock similar to that caused by a trapped hand or head.

If the safety mechanism is activated five or more times in a row, the safety mechanism will be cancelled and the door window will not close correctly. In such a case, the following procedure should be implemented to rectify this situation. If the window is open, repeatedly raise the driver’s door window switch until that window has been fully closed. Following this, release the switch, raise the switch once again and hold it in this condition for at least 1 second, then release it. You should now be able to operate in the normal fashion.

If the battery terminals are disconnected or the fuse for electric window is replaced, the safety mechanism will be cancelled and the door window will not automatically open/ close completely. If the window is open, repeatedly raise the driver’s door window switch until the window has been fully closed. Following this, release the switch, raise the switch once again and hold it in this condition for at least 1 second, then release it. You should now be able to operate the driver’s door window in the normal fashion.

Electric window control*

3-23

OKTE20E1

Locking and unlocking

Page 54

OKTE20E1

Page 55

Seat adjustment................................................................................... 4-02

Front seats........................................................................................... 4-02

Rear seat (Club cab and Double cab)*................................................4-04

Head restraints*...................................................................................4-05

Seat belts............................................................................................. 4-07

Pregnant women restraint....................................................................4-10

Seat belt pretensioner system and force limiter system*.................... 4-10

Child restraint......................................................................................4-11

Seat belt inspection............................................................................. 4-23

Supplemental restraint system (SRS)-airbag...................................... 4-24

Seat and seat belts

OKTE20E1

Page 56

Seat adjustment

Adjust the driver’s seat so that you are comfortable and that you can reach the pedals, steering wheel, switches etc. while retaining a clear field of vision.

WARNING

Do not attempt to adjust the seat while driving. This can cause loss of vehicle control and result in an accident. After adjustments are made, ensure the seating is locked in position by attempting to move the seat forward and rearward without using the adjusting mechanism.

It is extremely dangerous to ride in the cargo area (inside or outside) of a vehicle. Also, the cargo area and rear seats should never be used as a play area by children. In a collision, people or children riding unrestrained in these areas are more likely to be seriously injured or killed.

Do not allow people or children to ride in any area of your vehicle that is not equipped with seats and seat belts, and make sure that everyone travelling in your vehicle is in a seat and wearing a seat belt, or in the case of a child is strapped in a child restraint.

WARNING

To minimize the risk of personal injury in the event of a collision or sudden braking, the seatbacks should always be in the almost upright position while the vehicle is in motion. The protection provided by the seat belts may be reduced significantly when the seatback is reclined. There is greater risk that the passenger will slide under the seat belt, resulting in serious injury, when the seatback is reclined.

Do not place objects under the seats. This could prevent the seat from locking securely, and it could lead to an accident. It may also cause damage to the seat or other parts.

CAUTION

Make sure the seat is adjusted by an adult or with adult supervision for correct and safe operation.

Do not place a cushion or the like between your back and the seatback while driving. The effectiveness of the head restraints will be reduced in the event of an accident.

The reclining mechanism of the front manual seat’s seatback is spring loaded, causing it to fold the seatback forward when the lock lever is operated. When using the lever, sit close to the seatback or hold it with your hand to control its return motion.

When sliding the seats, be careful not to catch your hand or foot.

CAUTION

When sliding or reclining the seat rearward, pay careful attention to the rear seat passengers.

Front seats

Manual type

1- To adjust forward or backward

Lift the handle and adjust the seat to the desired position, and release the handle.

2- To recline the seatback

Pull the lever up and then lean backward to the desired position, and release the lever.

3- To adjust seat cushion height (driver’s

side only) Turn the dial and adjust the seat cushion height to the desired position.

Seat adjustment

4-02

OKTE20E1

Seat and seat belts

Page 57

Power type*

1- To adjust forward or backward

Operate the switch as indicated by the arrows and adjust the seat to the desired position.

2- To recline the seatback

Operate the switch as indicated by the arrows and adjust the seatback angle to the desired position.

3- To adjust seat height

Operate the switch as indicated by the arrows and adjust the seat height to the desired position. If the entire switch is operated, then the entire seat moves.

4- To adjust seat cushion angle

Operate the switch as indicated by the arrows and adjust the seat cushion angle to the desired position.

NOTE

To prevent the battery from running down, operate the switch with the engine running.

Heated seats*

The heated seats can be operated with the ignition switch or the operation mode in ON. Operate the switch as indicated by arrows. The indication lamp (A) will illuminate while the heater is on.

1 (HI) Heater high (for quick heating).

2 Heater off.

3 (LO) Heater low (to keep the seat

warm).

CAUTION

Operate in the high position for quick heating. Once the seat is warm, set the heater to low to keep it warm. Slight variations in seat temperature may be felt while using the heated seats. This is caused by the operation of the heater’s internal thermostat and does not indicate a malfunction.

If the following types of persons use the heated seats, they might become too hot or receive minor burns (red skin, heat blisters, etc.):

•

Children, elderly or ill people

•

People with sensitive skin

•

Excessively tired people

•

People under the influence of alcohol or sleep inducing medication (cold medicine, etc.)

Do not place heavy objects on the seat or stick pins, needles, or other pointed objects into it.

Do not use a blanket, cushion, or other material with high heat insulation properties on the seat while using the heater; this might cause the heater element to overheat

Do not use benzine, kerosene, petrol, alcohol or other organic solvents when cleaning the seats. Doing so could damage not only the seat cover, but also the heater element.

If water or any other liquid is spilled on the seat, allow it to dry thoroughly before attempting to use the heater.

Turn the heater off immediately if it appears to be malfunctioning during use.

Front seats

4-03

OKTE20E1

Seat and seat belts

Page 58

Rear seat (Club cab and Double cab)*

When a person is sitting in the middle seating position of the rear seat, adjust the head restraint to height at which it lock in position. Refer to “Head restraints*” on page 4-05.

Folding the seatback forward (Double cab)

Pull up the band on the top of the seatback and fold it forward.

To return (Double cab)

Raise the seatback until it is locked securely in place. Push and pull the seatback lightly to be sure it is secure.

Folding up the seat cushion (Club cab)

The right and left seat cushions can be folded up separately. To fold the seat cushions up, raise the seat cushions. Securely retain the seat cushion by hooking the retaining band (A) onto the head restraint (B) of the rear seat.

Armrest (Double cab)

To use the armrest, fold it down.

To return to the original position, push it backward (into the seatback) until it is level with the seat.

NOTE

Do not climb or sit on the armrest. Doing so could damage the armrest.

The top surface of the armrest contains a cup holder for rear seat occupants. Refer to “Cup holder” on page 7-104.

Rear seat (Club cab and Double cab)*

4-04

OKTE20E1

Seat and seat belts

Page 59

Head restraints*

WARNING

Driving without the head restraints in place can cause you and your passengers serious injury or death in an accident. To reduce the risk of injury in an accident, always make sure the head restraints are installed and properly positioned when the seat is occupied.

Never place a cushion or similar device on the seatback. This can adversely affect head restraint performance by increasing the distance between your head and the restraint.

To adjust height

Front seats

Adjust the head restraint height so that the centre of the head restraint is as close as possible to ear level to reduce the chances of injury in the event of collision. Any person too tall for the head restraint to reach their seated ear level, should adjust the restraint as high as possible.

To raise the head restraint, move it upward. To lower the restraint, move it downward while pushing the height adjusting knob (A) in the direction of the arrow. After adjustment, push the head restraint downward and make sure that it is locked.

Rear centre seat (Double cab)

To reduce the risk of injury in an accident, pull up the head restraint to the locked position.

To raise the head restraint, move it upward.

To lower the restraint, move it downward while pushing the height adjusting knob (A) in the direction of the arrow. After adjustment, push the head restraint downward and make sure that it is locked.

Head restraints*

4-05

OKTE20E1

Seat and seat belts

Page 60

WARNING

When a person sits in the middle seating position of the rear seat, pull up the head restraint to a height at which it locks in position. Be sure to make this adjustment before starting to drive. Serious injuries could otherwise be suffered as the result of an impact.

NOTE

The head restraint height of the outer seat in the rear seat cannot be adjusted.

To remove

Lift the head restraint with the height adjusting knob (A) pushed in.

To install

Confirm that the head restraint is facing the correct direction, and then insert it into the seatback while pressing the height adjusting knob (A) in the direction indicated by the arrow. The head restraint stalk with the adjustment notches (B) must be installed in the hole with the adjusting knob (A) (except head restraints of the outer seat).

CAUTION

Confirm that the height adjusting knob (A) is correctly adjusted as shown in the illustration, and also lift the head restraints to ensure that they do not come out of the seatback.

CAUTION

The shape and size of the head restraint differs according to the seat. Always use the correct head restraint provided for the seat and do not install the head restraint in the wrong direction.

Head restraints*

4-06

OKTE20E1

Seat and seat belts

Page 61

Seat belts

To protect you and your passengers in the event of an accident, it is most important that the seat belts are worn correctly while driving. The front seat belts each have a pretensioner system. (Club cab) The front seat belts and the rear outer seat belts each have a pretensioner system. (Double cab) These belts are used the same way as a conventional seat belt. Refer to “Seat belt pretensioner system and force limiter system*” on page 4-10.

WARNING

Seat belts should always be worn by every adult who drives or rides in this vehicle, and by all children who are tall enough to wear seat belts properly. Other children should always use proper child restraint systems.

Always place the shoulder belt over your shoulder and across your chest. Never put it behind you or under your arm.

One seat belt should be used by only one person. Doing otherwise can be dangerous.

WARNING

The seat belt will provide its wearer with maximum protection if the recliner seatback is placed in fully upright position. When the seatback is reclined, there is greater risk that the passenger will slide under the belt, especially in a forward impact accident, and may be injured by the belt or by striking the instrument panel or seatbacks.

Remove any twists when using the belt.

No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack.

Never hold a child in your arms or on your lap when riding in this vehicle, even if you are wearing your seat belt. To do so risks severe or fatal injury to the child in a collision or sudden stop.

Always adjust the seat belt to a snug fit.

Always wear the lap portion of the belt over your hips.

3-point type seat belt (with emergency locking mechanism)

This type of belt requires no length adjustment. Once worn, the belt adjusts itself to the movement of the wearer, but in the event of a sudden or strong shock, the belt automatically locks to hold the wearer’s body.

NOTE

You can check if the belt locks by pulling it forward quickly.

To fasten

1. Pull the seat belt out slowly while holding the latch plate.

NOTE

When the seat belts cannot be pulled out in a locked condition, pull the belts once forcefully and then return them. After that, pull the belts out slowly once again.

2. Insert the latch plate into the buckle until a “click” is heard.

Seat belts

4-07

OKTE20E1

Seat and seat belts

Page 62

WARNING

Never wear the lap portion of the belt across your abdomen. During accidents it can press sharply against the abdomen and increase the risk of injury.

The seat belts must not be twisted when worn.

3. Pull the belt slightly to adjust slackness as desired.

To unfasten

Hold the latch plate and push the button on the buckle.

NOTE

As the belt retracts automatically, keep holding the latch plate while retracting so that the belt stows slowly. Failure to do this could damage the vehicle.

NOTE

If the seat belt (A) or ring (B) becomes dirty, the belt may not retract smoothly. If the seat belt and ring are dirty, clean them with a mild soap or detergent solution.

Seat belt reminder

For the driver and the front passenger’s seat

[Mono-colour liquid crystal display type]

For the driver

For the front passenger

*- This warning lamp shows the case

of the left-hand drive vehicles.

Seat belts

4-08

OKTE20E1

Seat and seat belts

Page 63

[Colour liquid crystal display type]

For the driver

For the front passenger

*- This warning lamp shows the case

of the left-hand drive vehicles.

If the ignition switch is turned to the “ON” position or the operation mode is put in ON while the driver’s and/or the front passenger’s seat belt is not fastened, the warning lamp comes on and the tone sounds for approximately 6 seconds to remind the driver and/or the front passenger to fasten the seat belt. If the vehicle is driven with the seat belt still unfastened, the warning lamp will blink and the tone will sound intermittently until the seat belt is fastened.

WARNING

Do not install any accessory or sticker that makes the lamp difficult to see.

NOTE

If the seat belt subsequently remains unfastened, the warning lamp and the tone will issue further warnings each time the vehicle starts moving from a stop.

For the front passenger seat, the warning function works only while a person is sitting on the seat.

When luggage is placed on the front passenger seat, a sensor in the seat cushion may, depending on the weight and position of the luggage, cause the warning tone to sound and the warning lamp to come on.

For the rear passenger’s seats*

*- This warning lamp shows the

case of the 5-passenger vehicles.

If the ignition switch is turned to the “ON” position or the operation mode is put in ON while a seat belt is not fastened, the warning lamp comes on for approximately 30 seconds to remind the rear passenger to fasten the seat belt. If the vehicle is driven with the seat belt still unfastened, the warning lamps come on for approximately another 30 seconds. (This illumination happens only the first time the vehicle starts moving with the seat belt still unfastened.) The warning lamps go off when the seat belt is fastened.

WARNING

Do not install any accessory or sticker that makes the lamp difficult to see.

NOTE

The warning lamp comes on even if no one is sitting on the rear seats.

Seat belts

4-09

OKTE20E1

Seat and seat belts

Page 64

NOTE

If a seat belt is unfastened while the vehicle is being driven, the tone sounds for approximately 1 second and the warning lamp comes on for approximately 30 seconds. At the same time, the warning lamp for the seat where the seat belt is not fastened comes on.

If the seat belts are initially fastened but a seat belt is unfastened while the vehicle is stationary and the vehicle is then driven with the seat belt still unfastened, the warning lamp comes on again for approximately 30 seconds.

Adjustable seat belt anchor

The seat belt anchor height can be adjusted. To move the anchor, pull the lock knob (A) and slide the anchor to the desired position. Release the lock knob to lock the anchor into position.

WARNING

When adjusting the seat belt anchor, set it at a position that is sufficiently high so that the belt will make full contact with your shoulder but will not touch your neck.

Pregnant women restraint

WARNING

Seat belts work for everyone, including pregnant women. Pregnant women should use the available seat belts. This will reduce the likelihood of injury to both the woman and the unborn child. The lap belt should be worn across the thighs and as snug against the hips as possible, but not across the waist. Consult your doctor if you have any additional questions or concerns.

Seat belt pretensioner system and force limiter system*

The front seat belts each have a pretensioner system and force limiter system. (Club cab) The front seat belts and the rear outer seat belts each have a pretensioner system and force limiter system. (Double cab)

Pretensioner system

When the ignition switch or the operation mode is under the following conditions, if there is a frontal impact or a side impact (vehicles equipped with SRS side airbags and SRS curtain airbags) severe enough to injure the driver and/or front passenger or when a rollover or overturning of the vehicle is detected (if so equipped), the pretensioner system will retract the respective seat belts instantaneously, thus maximizing the seat belt’s effectiveness. [Except vehicles equipped with keyless operation system] The ignition switch is in the “ON” or “START” position. [Vehicles equipped with keyless operation system] The operation mode is in ON.

WARNING

To obtain the best results from your pretensioner seat belt, make sure you have adjusted your seat correctly and wear your seat belt properly.

Pregnant women restraint

4-10

OKTE20E1

Seat and seat belts

Page 65

CAUTION

Installation of audio equipment or repairs in the vicinity of the pretensioner seat belts or floor console must be performed in line with MITSUBISHI MOTORS guidelines. It is important to do so because the work could affect the pretensioner systems.

If you need to scrap the vehicle, please consult a MITSUBISHI MOTORS Authorized Service Point. It is important to do so because unexpected activation of the pretensioner seat belts could cause injuries.

NOTE

The pretensioner seat belts will be activated if the vehicle suffers a severe impact, even if the seat belts are not worn.

The pretensioner seat belts are designed to work only once. After the pretensioner seat belts have been activated, we recommend you to have them replaced by a MITSUBISHI MOTORS Authorized Service Point.

SRS warning

The same warning lamp/display is shared by the SRS airbags and the pretensioner seat belts. Refer to “SRS warning lamp/display” on page 4-34.

Force limiter system

In the event of a collision, each force limiter system will effectively absorb the load applied to the seat belt so as to minimize the impact to the passenger.

Child restraint

When transporting children in your vehicle, some type of child restraint system should always be used according to the size of the child. This is required by law in most countries. The regulations concerning driving with children in the front seat may differ from country to country. You are advised to comply with the relevant regulations.

WARNING

When possible, put children in the rear seat. Accident statistics indicate that children of all sizes and ages are safer when properly restrained in the rear seat rather than in the front seat.

Holding a child in your arms is no substitute for a restraint system. Failure to use a proper restraint system can result in severe or fatal injury to the child.

Each child restraint device or fixing is to be used only by one child.

WARNING

When attaching a child restraint system to the rear seat, adjust the front seat to prevent the front seatbacks from touching the child’s feet and child restraint system. Otherwise, the child could be seriously injured in the event of hard braking or a collision.

Caution for installing the child restraint on vehicles with a front passenger airbag

The label shown here is attached on vehicles with a front passenger airbag.

Child restraint

4-11

OKTE20E1

Seat and seat belts

Page 66

WARNING

Extreme Hazard! NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur.

NOTE

The labels may be in different positions depending on the vehicle model.

Use rearward facing child restraints in the rear seat or turn off the front passenger’s airbag ON-OFF switch. Refer to “To turn an airbag off” on page 4-27.

Front passenger's airbag ON

WARNING

A REARWARD FACING CHILD RESTRAINT must NOT be used in the front passenger seat if the front passenger’s airbag has not been deactivated. The force of an inflating airbag could kill or cause serious injuries to the child. A rearward facing child restraint should be used in the rear seat.

A FORWARD FACING CHILD RESTRAINT should be used in the rear seat whenever possible; if it must be used in the front passenger seat, turn off the front passenger’s airbag ON-OFF switch. Failure to do so could kill or cause serious injuries to the child.

Infants and small children

When transporting infants and small children in your vehicle, follow the instruction given below.

Instruction:

For small infants, an infant carrier should be used. For small children whose height when seated allows the shoulder belt to lie in contact with the face or the throat, a child seat should be used.

The child restraint system should be appropriate for the child’s weight and height and properly fit in the vehicle. For a higher degree of safety: THE CHILD RESTRAINT SYSTEM SHOULD BE INSTALLED IN THE REAR SEAT.

Before purchasing a child restraint system, try installing it in the seat to make sure there is a good fit. Because of the location of the seat belt buckles and the shape of the seat cushion, it may be difficult to securely install some manufacturer’s child restraint systems. If the child restraint system can be pulled forward or to either side easily on the seat cushion after the seat belt has been tightened, choose another manufacturer’s child restraint system.

Child restraint

4-12

OKTE20E1

Seat and seat belts

Page 67

WARNING

When installing a child restraint system, refer to the instructions provided by the manufacturer of the restraint system. Failure to do so can result in severe or fatal injury to the child.

After installation, push and pull the child restraint system back and forth, and side to side, to see that it is properly secured. If the child restraint system is not installed securely, it may cause injury to the child or other occupants in the case of accident or sudden stops.

When the child restraint system is not in use, keep your child restraint system fixed firmly or remove it from the vehicle in order to prevent it from being thrown around inside the vehicle during an accident.

NOTE

Depending on the seating position in the vehicle and the child restraint system that you have, the child restraint can be attached using one of the following two locations:

•

Using the lower anchorage in the rear seat ONLY if the child restraint has ISOFIX/iSize mountings (Double cab) (See page 4-21).

•

Using the seat belt (See page 4-21).

Older children

Children who have outgrown the child restraint system should be seated in the seat and wear combination lap shoulder belt. The lap portion of the belt should be snug and positioned low on the abdomen so that it is below the top of the hip-bone. Otherwise, the belt could intrude into the child’s abdomen during an accident and cause injury.

Child restraint

4-13

OKTE20E1

Seat and seat belts

Page 68

Suitability for various ISOFIX positions (Double cab)

Mass group Size class Fixture

Vehicle ISO-

FIX positions*

Recommended Child

Restraint Systems*

UN-R44 Approval

No.

UN-R129 Approval

No.

Rear outboard

Carrycot

F ISO/L1 X — — —

G ISO/L2 X — — —

0 - Up to 10 kg E ISO/R1 IL — — —

0+ - Up to 13 kg

E ISO/R1 IL — — —

— ISO/R2X IL — — —

D ISO/R2 IL, IL#

BABY-SAFE i-SIZE:

MZ315055

BABY-SAFE i-SIZE

FLEX BASE:

MZ315056

— E1-000008

C ISO/R3 IL — — —

I - 9 kg to 18 kg

— ISO/R2X IL — — —

D ISO/R2 IL — — —

C ISO/R3 IL — — —

B ISO/F2 IUF — — —

B1 ISO/F2X IUF, IL# DUO plus: MZ313045 E1-04301133 —

A ISO/F3 IUF — — —

II & III - 15 kg to 36 kg

— — IL# KIDFIX XP:

MZ315025

E1-04301304 —

*1: Vehicles with ISOFIX marking and i-SIZE marking (Refer to “Lower anchorage location” on page 4-20.) *2: MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.

Child restraint

4-14

OKTE20E1

Seat and seat belts

Page 69

For detailed information, consult your MITSUBISHI MOTORS Authorized Service Point.

CAUTION

When installing a child restraint system, remove the head restraint from the seat.

When attaching a child restraint system to the rear seat, adjust the front seat to prevent the front seatbacks from touching the child’s feet and child restraint system.

“BABY-SAFE i-SIZE” and “BABY-SAFE i-SIZE FLEX BASE” are designed for children 40-83 cm in height.

Definition of characters to be inserted in the table above:

IUF- Suitable for ISOFIX forward restraint child restraint systems of universal category approved for use in the mass group.

IL- Suitable for ISOFIX child restraint systems of semi-universal category approved for use in the mass group.

IL# - Suitable for particular ISOFIX child restraint systems of MITSUBISHI MOTORS GENUINE Parts. See the above table of “Recommended Child Restraint Systems”

X- ISOFIX position not suitable for ISOFIX child restraint systems in this mass group.

i-Size child restraint system (Double cab)

Seating Position*

Recommended Child

Restraint Systems*

UN-R129 Approval

No.

Front passenger Second outboard Rear centre

i-Size child restraint

system

X i-U X

BABY-SAFE i-SIZE:

MZ315055

BABY-SAFE i-SIZE

FLEX BASE:

MZ315056

E1-000008

*1: Vehicles with i-Size marking. (Refer to “Lower anchorage location” on page 4-20.) *2: MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.

For detailed information, consult your MITSUBISHI MOTORS Authorized Service Point.

Child restraint

4-15

OKTE20E1

Seat and seat belts

Page 70

CAUTION

“BABY-SAFE i-SIZE” and “BABY-SAFE i-SIZE FLEX BASE” are designed for children 40-83 cm in height, and up to 13 kg in weight.

Definition of characters to be inserted in the table above:

i-U- Suitable for i-Size “universal” child restraint system forward and rearward facing.

X- Seating position not suitable for i-Size “universal” child restraint systems.

Suitability for various seating positions Club cab

Mass group

Seating position

Recommended Child

Restraint Systems

UN-R44

Approval No.

UN-R129

Approval No.

Front passenger

Rear Out-

board

Activated air-

bag

Deactivated

airbag

0 - Up to 10 kg X U X — — —

0+ - Up to 13 kg

X U, L# X

BABY-SAFE i-SIZE:

MZ315055

— E1-000008

I - 9 kg to 18 kg X U, L# X DUO plus: MZ313045 E1-04301133 —

II & III - 15 kg to 36 kg

U*3, L#

KIDFIX XP:

MZ315025

E1-04301304 —

: MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.

For detailed information, consult your MITSUBISHI MOTORS Authorized Service Point.

: The front passenger’s airbag is deactivated by using the front passenger’s airbag ON-OFF switch.

: Do not remove the head restraint when installing a booster cushion.

Child restraint

4-16

OKTE20E1

Seat and seat belts

Page 71

CAUTION

When installing a child restraint system, remove the head restraint from the seat. However, do not remove the head restraint when installing a booster cushion (see 4-22.)

When installing a child restraint system (Mass group II & III) on the front passenger seat, please move the seatbacks position to 2 steps rearward from upright position.

“BABY-SAFE i-SIZE” is designed for children 40-83 cm in height.

Definition of characters to be inserted in the table above:

U- Suitable for “universal” category restraints approved for use in this mass group.

L#- Suitable for particular child restraint systems of MITSUBISHI MOTORS GENUINE Parts. See the above table of “Recommended Child Restraint Systems”.

X- Seating position not suitable for children in this mass group.

Double cab

Mass group

Seating position

Recommen-

ded Child

Restraint

Systems

UN-R44

Approval No.

UN-R129

Approval No.

Front passenger

Rear Out-

board

Rear centre

Activated air-

bag

Deactivated

airbag

0 - Up to 10 kg X U U U — — —

0+ - Up to 13 kg

X U, L# U, L# U, L#

BABY-SAFE

i-SIZE:

MZ315055

— E1-000008

I - 9 kg to 18 kg X U, L# U, L# U, L#

DUO plus: MZ313045

E1-04301133 —

: MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.

For detailed information, consult your MITSUBISHI MOTORS Authorized Service Point.

: The front passenger’s airbag is deactivated by using the front passenger’s airbag ON-OFF switch.

: Do not remove the head restraint when installing a booster cushion.

Child restraint

4-17

OKTE20E1

Seat and seat belts

Page 72

Mass group

Seating position

Recommen-

ded Child

Restraint

Systems

UN-R44

Approval No.

UN-R129

Approval No.

Front passenger

Rear Out-

board

Rear centre

Activated air-

bag

Deactivated

airbag

II & III - 15 kg to 36 kg

U*3, L# U*3, L#

KIDFIX XP:

MZ315025

E1-04301304 —

: MITSUBISHI MOTORS Europe B.V. reserves the right to changes without any prior announcement.

For detailed information, consult your MITSUBISHI MOTORS Authorized Service Point.

: The front passenger’s airbag is deactivated by using the front passenger’s airbag ON-OFF switch.

: Do not remove the head restraint when installing a booster cushion.

CAUTION

When installing a child restraint system, remove the head restraint from the seat. However, do not remove the head restraint when installing a booster cushion (see 4-22.)

Do not attach a child restraint system with support leg to the rear centre seat.

When installing a child restraint system (Mass group II & III) on the front passenger seat, please move the seatbacks position to 2 steps rearward from upright position.

When attaching a child restraint system to the rear seat, adjust the front seat to prevent the front seatbacks from touching the child’s feet and child restraint system.

Pull down the head restraint of the child restraint after the child gets down from the child restraint when you use the “KIDFIX XP” in the rear seat to prevent the head restraint of the child restraint from touching the rear glass. And make sure the head restraint is adjusted and properly positioned when the child sits in the child restraint system.

“BABY-SAFE i-SIZE” is designed for children 40-83 cm in height.

Definition of characters to be inserted in the table above:

U- Suitable for “universal” category restraints approved for use in this mass group.

L#- Suitable for particular child restraint systems of MITSUBISHI MOTORS GENUINE Parts. See the above table of “Recommended Child Restraint Systems”.

X- Seating position not suitable for children in this mass group.

Child restraint

4-18

OKTE20E1

Seat and seat belts

Page 73

Booster seat Club cab

Seating position

Front passenger

Rear outboard

Activated airbag

Deactivated Airbag

Booster fixture X B2, B3 X

: The front passenger’s airbag is deactivated by using the front passenger’s airbag ON-OFF switch.

CAUTION

When installing a child restraint system, remove the head restraint from the seat.

Definition of characters to be inserted in the table above:

B2 - Suitable for ISO/B2 booster fixture

B3 - Suitable for ISO/B3 booster fixture

X- Seating position not suitable for booster seats

Double cab

Seating position

Front passenger

Rear outboard Rear centre

Activated airbag

Deactivated Airbag

Booster fixture X B2, B3 B2, B3 X

: The front passenger’s airbag is deactivated by using the front passenger’s airbag ON-OFF switch.

Child restraint

4-19

OKTE20E1

Seat and seat belts

Page 74

CAUTION

When installing a child restraint system, remove the head restraint from the seat.

Definition of characters to be inserted in the table above:

B2 - Suitable for ISO/B2 booster fixture

B3 - Suitable for ISO/B3 booster fixture

X- Seating position not suitable for booster seats

Installing a child restraint system to the lower anchorage (ISOFIX/i-Size child restraint mountings) and tether anchorage (Double cab)

Lower anchorage location

Your vehicle’s rear seat is fitted with lower anchorages for attaching a child restraint system with ISOFIX/i-Size mountings.

Type 1 (ISOFIX marking)

Type 2 (i-size marking)

Tether anchorage location

There are 2 child restraint anchorage points on the vertical panel, located behind the rear seat.

These are for securing a child restraint system tether strap to each of the 2 rear seating positions in your vehicle.

*: Front of the vehicle

Child restraint

4-20

OKTE20E1

Seat and seat belts

Page 75

WARNING

Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses, or for attaching other items or equipment to the vehicle.

Child restraint system with ISOFIX/i-Size mountings (Double cab)

The child restraint system is designed only for seats that incorporate lower anchorages. Retain the child restraint system using the lower anchorages. It is not necessary to retain the child restraint system using the vehicle’s seat belts.

A- Child restraint system connectors

To install

1. Remove any foreign material in or around the connectors and ensure the vehicle seat belt is in its normal storage position.

2. Remove the head restraint from the location in which you wish to install a child restraint. Refer to “Head restraints*” on page 4-05.

3. Push the child restraint system’s connectors (A) into the lower anchorages (B) in accordance with the instructions provided by the child restraint system’s manufacturer.

A- Connector

B- Lower anchorage If your child restraint system has a support leg, make sure that there is a sup-

port leg at the stable position on the floor. If your child restraint system with a tether strap, perform the step 4 through 8. If your child restraint system without a tether strap, perform the step 8.

4. Drop the child restraint’s tether strap (C) down from the clearance between the rear seatback and back panel trim.

Child restraint

4-21

OKTE20E1

Seat and seat belts

Page 76

5. Tip the armrest forward. Open the two fasteners (D) that are located in the space where the armrest are stowed.

6. Open the inner cover.

7. Put your hand in the opening of the two fasteners, attach the tether strap hook (E) to the tether anchorage (F), and securely tighten the tether strap.

NOTE

If it is difficult to latch the tether strap hook, turn the hook sideways.

8. Push and pull the child restraint system in all directions to be sure it is firmly secured.

To remove

Remove the child restraint system in accordance with the instructions provided by the child restraint system’s manufacturer.

Installing a child restraint system to a 3-point type seat belt (with emergency locking mechanism)

Installation:

1. Put a child restraint system on the seat in which you wish to install it and remove the head restraint from the seat. Refer to “Head restraints*” on page 4-05.

CAUTION

Do not remove the head restraint when installing a booster cushion.

2. When installing a child restraint system in the front passenger seat, adjust seat slide to its most rearward position.

Child restraint

4-22

OKTE20E1

Seat and seat belts

Page 77

3. Route the belt through the child restraint according to the child restraint system manufacturer’s instructions, then insert the latch plate into the buckle.

4. Remove all slack by using the locking clip (A).

5. If your child restraint system has a support leg, make sure that there is a support leg at the stable position on the floor.

6. Before putting the child in the restraint, push and pull the child restraint in all directions to be sure it is secure. Do this before each use.

WARNING

For some types of child restraint, the locking clip (A) should be used to help avoid personal injury during a collision or sudden manoeuvre. It must be fitted and used in accordance with the child restraint manufacturer’s instructions. The locking clip must be removed when the child restraint is removed.

Seat belt inspection

Check the belts for cuts, worn or frayed webbing and for cracked or deformed metallic parts. Replace the belt assembly if it is defective.

WARNING

We recommend you to have all seat belt assemblies including retractors and attaching hardware inspected after any collision. We recommend that seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly.

WARNING

Do not attempt to repair or replace any part of the seat belt assemblies; we recommend you to have this work done by a MITSUBISHI MOTORS Authorized Service Point. Incorrect repair or replacement could reduce the effectiveness of the belts and could result in serious injury in the event of a collision.

Once the pretensioner has been activated, it cannot be re-used. It must be replaced together with the retractor.

Do not insert any foreign objects (pieces of plastic, paper clips, buttons, etc.) in the buckle or retractor mechanism. In addition, do not modify, remove or install the seat belt. Otherwise, the seat belt may not be able to provide adequate protection in a collision or other situation.

Seat belt inspection

4-23

OKTE20E1

Seat and seat belts

Page 78

WARNING

A dirty belt should be cleaned with neutral detergent in warm water. After rinsing in water, let it dry in the shade. Do not attempt to bleach or re-dye the belts because this will affect their characteristics.

Supplemental restraint system (SRS)-airbag

The information for SRS airbags includes important information concerning the driver’s and front passenger’s airbags, the driver’s knee airbag, the side airbags and the curtain airbags.

The SRS driver’s and front passenger’s airbags are designed to supplement the primary protection of the driver and front passenger side seat belt systems by providing those occupants with protection against head and chest injuries in certain moderate-to-severe frontal collisions.

The SRS driver’s knee airbag (if so equipped) is designed to supplement the primary protection of the driver’s seat belt system. It can reduce the forward movement of the driver’s lower legs and provide increased overall body protection in certain moderateto-severe frontal collisions.

The SRS side airbags (if so equipped) are designed to supplement properly worn seat belts and provide the driver and front passenger with protection against chest injuries in certain moderate-to-severe side impact collisions.

The SRS curtain airbags (if so equipped) are designed to supplement properly worn seat belts and provide the driver and passengers on the front seat and rear outboard seat with protection against head injuries by deploying the curtain airbag on the side impacted in moderate-to-severe side impact collisions.

The SRS is NOT a substitute for the seat belts. To ensure the maximum protection during all types of collisions and accidents, all occupants, including the passengers as well as the driver, must wear their seat belts.

NOTE

The ERA-GLONASS (if so equipped) is designed to operate when any of the airbags deploy. Refer to “ERA-GLONASS*” on page 8-02

How the Supplemental Restraint System works

The SRS includes the following components:

1. Airbag module (Driver)

2. Front passenger’s airbag indicator

3. Airbag module (Passenger)

4. Driver’s knee airbag module*

5. Front passenger’s airbag ON-OFF switch

6. Side airbag modules*

7. Curtain airbag modules*

Supplemental restraint system (SRS)-airbag

4-24

OKTE20E1

Seat and seat belts

Page 79

Only when the ignition switch or the operation mode is under the following conditions, the airbags will operate. [Except vehicles equipped with keyless operation system] The ignition switch is in the “ON” or “START” position. [Vehicles equipped with keyless operation system] The operation mode is in ON. When the airbag control unit detects a rollover of the vehicle, the curtain airbags will be deployed. (if so equipped) The airbags deployment produces a sudden, loud noise, and releases some smoke and powder, but these conditions are not injurious, and do not indicate a fire in the vehicle. People with respiratory problems may feel some temporary irritation from chemicals used to produce the deployment; open the windows after airbag deployment, if safe to do so. The airbags deflate very rapidly after deployment, so there is little danger of obscured vision.

CAUTION

Airbags inflate at an extremely rapid speed. In certain situations, contact with inflating airbags can result in abrasions, bruises, light cuts, and the like.

WARNING

IT IS VERY IMPORTANT TO BE PROPERLY SEATED. A driver or front passenger too close to the steering wheel or instrument panel during airbag deployment can be killed or seriously injured. Airbags inflate very fast, and with great force. If the driver and front passenger are not properly seated and restrained, the airbags may not protect you properly, and could cause serious or fatal injuries when they inflate.

Do not sit on the edge of the seat, or sit with your lower legs too close to the instrument panel, or lean head or chest close to the steering wheel or instrument panel. Do not put feet or legs on or against the instrument panel.

Place all infants and small children in the rear seat and properly restrained using an appropriate child restraint system. The rear seat is the safest place for infants and children.

WARNING

Infants and small children should never be unrestrained, stand up against the instrument panel or be held in your arms or on your lap. They could be seriously injured or killed in a collision, including when the airbag inflates. They should be properly seated in an appropriate child restraint system. See the “Child restraint” section of this owner’s manual.

Supplemental restraint system (SRS)-airbag

4-25

OKTE20E1

Seat and seat belts

Page 80

WARNING

Older children should be seated, properly wearing the seat belt, with an appropriate booster seat if needed.

Caution for installing the child restraint on vehicles with front passenger’s airbag

The label shown here is attached on vehicles with front passenger’s airbag.

WARNING

Extreme Hazard! NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur.

NOTE

The labels may be in different positions depending on the vehicle model.

Front passenger’s airbag ONOFF switch

The front passenger’s airbag ON-OFF switch can be used to disable the front passenger’s airbag. If you have a child restraint system that cannot be fitted to any seat other than the front passenger seat, be sure to turn OFF the front passenger’s airbag ON-OFF switch before using it. (Refer to “To turn an airbag off” on page 4-27) The front passenger’s airbag ON-OFF switch is located as shown in the illustration.

Front passenger’s airbag indicator

The front passenger’s airbag indicator is located in the instrument panel.

Type 1

Type 2

The both indicator normally comes on when the ignition switch is turned to the “ON” position or the operation mode is put in ON, and goes off a few seconds later. When the front passenger’s airbag ON-OFF switch is turned OFF, the OFF indicator will stay on to show that the front passenger’s airbag is not operational. When the front passenger’s airbag ON-OFF switch is turned ON, the OFF indicator goes off, and the ON indicator comes on for approximately 1 minute to show that the front passenger’s airbag is operational.

Supplemental restraint system (SRS)-airbag

4-26

OKTE20E1

Seat and seat belts

Page 81

WARNING

Do not fit any accessory that makes the indication lamp impossible to see, and do not cover the indication lamp with a sticker. You would not be able to verify the status of the passenger airbag system.

To turn an airbag off

WARNING

To reduce risk of serious or fatal injury:

•

Always turn the ignition switch to the “LOCK” position or put the operation mode in OFF, before operating the front passenger’s airbag ON-OFF switch. Failure to do so could adversely affect the airbag performance.

•

Wait at least 60 seconds to operate the front passenger’s airbag ON-OFF switch after turning the ignition switch to the “LOCK” position or putting the operation mode in OFF. The SRS airbag system is designed to retain enough voltage to deploy the airbag.

•

Always remove the key from the front passenger’s airbag ON-OFF switch after operating that switch. Failure to do so could lead to improper position of the front passenger’s airbag ON-OFF switch.

WARNING

•

Do not turn OFF the front passenger’s airbag ON-OFF switch except when a child restraint system is fitted to the front passenger seat.

•

If the OFF indicator does not come on when the front passenger’s airbag ONOFF switch is turned OFF, do not fit a child restraint system to the front passenger seat. We recommend you to have the system inspected by a MITSUBISHI MOTORS Authorized Service Point.

•

If the OFF indicator remains on when the front passenger’s airbag ON-OFF switch is turned ON, do not allow anyone to sit on the front passenger seat. We recommend you to have the system inspected by a MITSUBISHI MOTORS Authorized Service Point.

To turn an airbag off, follow these steps:

1. Insert the key into the front passenger’s airbag ON-OFF switch, and turn it to the “OFF” position.

2. Remove the key from the front passenger’s airbag ON-OFF switch.

3. Turn the ignition switch to the “ON” position or put the operation mode in ON. The front passenger’s airbag OFF indication lamp will stay on.

AHA109190

Type 1

Type 2

The front passenger’s airbag is now deactivated and will not deploy until switched on again.

Driver’s and front passenger’s airbag system

The driver’s airbag is located under the padded cover in the middle of the steering wheel. The front passenger’s airbag is contained in the instrument panel above the glove box.

Supplemental restraint system (SRS)-airbag

4-27

OKTE20E1

Seat and seat belts

Page 82

The driver’s airbag and the front passenger’s airbag are designed to inflate at the same time even if the passenger seat is not occupied.

Driver’s knee airbag system*

The driver’s knee airbag is located under the steering wheel. The driver’s knee airbag is designed to deploy at the same time as the driver’s front airbag.

Deployment of front airbags and driver’s knee airbag

The front airbags and driver’s knee airbag ARE DESIGNED TO DEPLOY when…

The front airbags and driver’s knee airbag are designed to deploy when the vehicle suffers a moderate to severe frontal impact. The typical condition is shown in the illustration.

1- Head-on collision with a solid wall at

speed of approximately 25 km/h (16 mph) or higher

2- Moderate-to-severe frontal impact with-

in the shaded area between the arrows

The front airbags and driver’s knee airbag will deploy if the severity of impact is above the designed threshold level, comparable to an approximately 25 km/h (16 mph) collision when impacting straight into a solid wall that does not move or deform. If the severity of the impact is below the above threshold level, the front airbags and driver’s knee airbag may not deploy. However, this threshold speed will be considerably higher if the vehicle strikes an object that absorbs the impact by either deforming or moving (for example, another stationary vehicle, pole or a guard rail). Because frontal collisions can easily move you out of position, it is important to always properly wear your seat belts. Your seat belts will help keep you a safe distance from the steering wheel and instrument panel during the initial stages of airbag deployment. The initial stage of airbag inflation is the most forceful, and can possibly cause serious or fatal injuries. Moreover, the seat belts in your vehicle are your primary means of protection in a collision. The SRS airbags are designed to provide additional protection. Therefore, for your safety and the safety of all occupants, be sure to always properly wear your seat belts.

Supplemental restraint system (SRS)-airbag

4-28

OKTE20E1

Seat and seat belts

Page 83

The front airbags and driver’s knee airbag MAY NOT DEPLOY when…

With certain types of frontal collisions, the vehicle’s body structure is designed to absorb the shock to help protect the occupants from harm. (The vehicle body’s front area may deform significantly as it absorbs the impact.) Under such circumstances, the front airbags and driver’s knee airbag may not deploy irrespective of the deformation and damage to the vehicle body. Examples of some typical conditions are shown in the illustration.

1- Collision with a utility pole, tree or other

narrow object

2- Vehicle slides under the rear body of a

truck

3- Oblique frontal impacts

Because the front airbags and driver’s knee airbag do not protect the occupant in all types of frontal collisions, be sure to always properly wear your seat belts.

The front airbags and driver’s knee airbag ARE NOT DESIGNED TO DEPLOY when…

The front airbags and driver’s knee airbag are not designed to deploy in conditions where they cannot typically provide protection to the occupant. Such conditions are shown in the illustration.

1- Rear end collisions 2- Side collisions 3- Vehicle rolls onto its side or roof

Because the front airbags and driver’s knee airbag do not protect the occupant in all types of collisions, be sure to always properly wear your seat belts.

The front airbags and driver’s knee airbag MAY DEPLOY when…

The front airbags and driver’s knee airbag may deploy if the bottom of the vehicle suffers a moderate-to-severe impact (undercarriage damage). Examples of some typical conditions are shown in the illustration.

1- Collision with an elevated median/island

or kerb

2- Vehicle travels over a deep hole/pothole 3- Vehicle drives down a steep slope and

hits the ground

Supplemental restraint system (SRS)-airbag

4-29

OKTE20E1

Seat and seat belts

Page 84

Because the front airbags and driver’s knee airbag may deploy in certain types of unexpected impacts as shown in the illustration that can easily move you out of position, it is important to always properly wear your seat belts. Your seat belts will help keep you a safe distance from the steering wheel and instrument panel during the initial stages of airbag deployment. The initial stage of airbag inflation is the most forceful and can possibly cause serious or fatal injuries if you contact it at this stage.

WARNING

Do not attach anything to the steering wheel’s padded cover, such as badges or accessories. It might strike and injure an occupant if the airbag inflates.

Do not set anything on, or attach anything to, the instrument panel above the glove box. It might strike and injure an occupant if the airbag inflates.

WARNING

Do not attach accessories to, or put them in front of, the windscreen. These objects could restrict the airbag inflation, or strike and injure an occupant if the airbags inflate.

Do not attach additional keys or accessories (hard, pointed or heavy objects) to the ignition key. Such objects could prevent the driver’s knee airbag from inflating normally or could be propelled to cause serious injury if the airbag inflates.

Do not attach accessories to the lower portion of the driver’s side instrument panel. Such objects could prevent the driver’s knee airbag from inflating normally or could be propelled to cause serious injury if the airbag inflates.

WARNING

Do not put packages, pets or other objects between the airbags and the driver or front passenger. It could affect airbag performance, or could cause injury when the airbag inflates.

Right after the airbag inflation, several airbag system components will be hot. Do not touch these components. There is a danger of being burnt.

The airbag system is designed to work only once. Once the airbags have deployed, they will not work again. They must promptly be replaced and we recommend you to have the entire airbag system inspected by a MITSUBISHI MOTORS Authorized Service Point.

Side airbag system*

The side airbags (A) are contained in the driver and front passenger seatbacks.

Supplemental restraint system (SRS)-airbag

4-30

OKTE20E1

Seat and seat belts

Page 85

The side airbag is designed to inflate only on the side of the vehicle that is impacted, even with no passenger in the front seat.

The label shown here is attached to the seatbacks with a side airbag.

Curtain airbag system*

The curtain airbags are contained in the front pillars and roof side rail. The curtain airbag is designed to inflate only on the side of the vehicle that is impacted, even with no passenger in the front seat or rear seat. Also, when the airbag control unit detects a rollover of the vehicle, the curtain airbags will deploy.

Deployment of side airbags and curtain airbags*

The side airbags and curtain airbags ARE DESIGNED TO DEPLOY when...

The side airbags and curtain airbags are designed to deploy when the vehicle suffers a moderate-to-severe side impact to the middle of the passenger compartment. The typical condition is shown in the illustration.

1. Moderate to severe impact to the middle of the vehicle body’s side structure

2. When the vehicle detects a rollover of the vehicle (curtain airbag only)*

Supplemental restraint system (SRS)-airbag

4-31

OKTE20E1

Seat and seat belts

Page 86

The seat belts in your vehicle are your primary means of protection in a collision. The SRS side airbags and curtain airbags are designed to provide additional protection. Therefore, for your safety and the safety of all occupants, be sure to always properly wear your seat belts.

The side airbags and curtain airbags MAY NOT DEPLOY when...

With certain types of side collisions, the vehicle’s body structure is designed to absorb the shock to help protect the occupants from harm. (The vehicle body’s side area may deform significantly as it absorbs the impact.) Under such circumstances, the side airbags and curtain airbags may not deploy irrespective of the deformation and damage to the vehicle body. Examples of some typical conditions are shown in the illustration.

1. Side impacts in an area away from the passenger compartment

2. Motorcycle or other similar small vehicle collides with the side of vehicle

3. Collision with a utility pole, tree or other narrow object

4. Oblique side impacts

5. Vehicle rolls onto its side or roof

Because the side airbags and curtain airbags do not protect the occupant in all types of side collisions, be sure to always properly wear your seat belts.

The side airbags and curtain airbags ARE NOT DESIGNED TO DEPLOY when...

The side airbags and curtain airbags are not designed to deploy in conditions where they cannot usually provide protection to the occupant. Typical conditions are shown in the illustration.

1. Head-on collisions

2. Rear end collisions

3. Pitch end over end*

Supplemental restraint system (SRS)-airbag

4-32

OKTE20E1

Seat and seat belts

Page 87

Because the side airbags and curtain airbags do not protect the occupant in all types of collisions, be sure to always properly wear your seat belts.

WARNING

The side airbags and curtain airbags are designed to supplement the driver and passenger seat belts in certain side impacts. Seat belts should always be worn properly, and the driver and passenger should sit well back and upright without leaning against the window or door.

The side airbag and curtain airbag inflate with great force. The driver and passenger should not put their arms out of the window, and should not lean against the door, in order to reduce the risk of serious or possible fatal injury from the deploying side airbag and curtain airbag.

WARNING

Do not allow any rear seat occupant to hold onto the seatback of either front seat, in order to reduce risk of injury from the deploying side airbag. Special care should be taken with children.

Do not place any objects near or in front of the seatback of either front seat. They could interfere with proper side airbag inflation, and also could cause injury if thrown free by side airbag deployment.

Do not place stickers, labels or additional trim on the seatback of either front seat. They could interfere with proper side airbag inflation.

Do not install seat covers on seats with side airbags. Do not re-cover seats that have side airbags. This could interfere with proper side airbag inflation.

Do not attach a microphone (B) or any other device or object around the part where the curtain airbags (A) activate such as on the windscreen, side door glass, front and rear pillars and roof side or assist grips. When the curtain airbags inflate, the microphone or other device or object will be hurled with great force or the curtain airbags may not activate correctly, resulting in death or serious injury.

WARNING

Do not put a hanger or any heavy or pointed object on the coat hook. If the curtain airbag was activated, any such item could be propelled away with great force and could prevent the curtain airbag from inflating correctly. Hang clothes directly on the coat hook (without using a hanger). Make sure there are no heavy or sharp objects in the pockets of clothes that you hang on the coat hook.

Do not allow a child to lean against or close to the front door even if the child is seated in a child restraint system. The child’s head should also not lean against or be close to the area where the side airbag and curtain airbag are located. It is dangerous if the side airbag and curtain airbag inflate. Failure to follow all of these instructions could lead to serious or fatal injury to the child.

Supplemental restraint system (SRS)-airbag

4-33

OKTE20E1

Seat and seat belts

Page 88

WARNING

We recommend work around and on the side airbags and curtain airbags system to be done by a MITSUBISHI MOTORS Authorized Service Point.

SRS warning lamp/display

Type 1

Type 2

There is a Supplemental Restraint System (“SRS”) warning lamp on the instrument panel. The system checks itself every time the ignition switch is turned to the “ON” position or the operation mode is put in ON. The SRS warning lamp will come on for several seconds and then go out. This is normal and means the system is working properly.

If there is a problem involving one or more of the SRS components, the warning lamp will come on and stay on. At the same time, the warning display will appear on the information screen in the multi information display (Type 1 only). The SRS warning lamp/display is shared by the SRS airbag and the seat belt pretensioner system.

WARNING

If any of the following conditions occur, there may be a problem with the SRS airbags and/or seat belt pretensioners, and they may not function properly in a collision or may suddenly activate without a collision:

•

Even when the ignition switch or the operation mode is in ON, the SRS warning lamp does not come on or it remains on.

•

The SRS warning lamp and/or the warning display comes on while driv-

ing. The SRS airbags and seat belt pretensioners are designed to help reduce the risk of serious injury or death in certain collisions. If either of the above conditions occurs, immediately have your vehicle checked by a MITSUBISHI MOTORS Authorized Service Point.

NOTE

On vehicles equipped with the ERA-GLONASS, if the ERA-GLONASS system operates, the SRS warning lamp illuminates.

SRS servicing

WARNING

We recommend any maintenance performed on or near the components of the SRS to be performed by a MITSUBISHI MOTORS Authorized Service Point. Improper work on the SRS components or wiring could result in inadvertent deployment of the airbags, or could render the SRS inoperative; either situation could result in serious injury.

Do not modify your steering wheel, seat belt retractor or any other SRS components. For example, replacement of the steering wheel, or modifications to the front bumper or body structure can adversely affect SRS performance and lead to possible injury.

If your vehicle has sustained any damage, we recommend you to have the SRS inspected to ensure it is in proper working order.

Supplemental restraint system (SRS)-airbag

4-34

OKTE20E1

Seat and seat belts

Page 89

WARNING

On vehicles with the side airbags, do not modify your front seats, centre pillar and centre console. It can adversely affect SRS performance and lead to possible injury.

If you found any tear, scratch, crack or damage to the portion where the airbag is stored, you should have the SRS inspected by a MITSUBISHI MOTORS Authorized Service Point.

NOTE

If your vehicle has to be scrapped, do this in line with the local legislation and contact a MITSUBISHI MOTORS Authorized Service Point to safely dismantle the airbag system.

Supplemental restraint system (SRS)-airbag

4-35

OKTE20E1

Seat and seat belts

Page 90

OKTE20E1

Page 91

Instruments..........................................................................................5-02

Multi information display - Type 1.....................................................5-03

Multi information display - Type 2.....................................................5-17

Indication lamp, warning lamp, and information screen

display list (multi information display - Type 1)............................5-25

Indication and warning lamps (multi information display -

Type 2)............................................................................................5-49

Indication lamps..................................................................................5-50

Warning lamps.................................................................................... 5-51

Information screen display (Vehicles equipped with the

multi information display - Type 1)................................................5-53

Combination headlamps and dipper switch........................................ 5-55

Headlamp levelling switch..................................................................5-61

Turn-signal lever................................................................................. 5-62

Hazard warning flasher switch............................................................5-62

Fog lamp switch..................................................................................5-63

Wiper and washer switch.................................................................... 5-64

Rear window demister switch............................................................. 5-68

Heated steering wheel*....................................................................... 5-70

Horn switch.........................................................................................5-70

Instruments and controls

OKTE20E1

Page 92

Instruments

Type 1

Type 2

1- Tachometer

The tachometer indicates the engine speed (r/min). The tachometer helps you to obtain more economical driving and also warns you of excessive engine speeds (Red zone).

2- Multi information display (Type 1: Col-

our liquid crystal display type) ® p. 5-03 Information screen display list (Type 1) ® p. 5-26 Multi information display (Type 2: Mono-colour liquid crystal display type)

® p. 5-17 3- Speedometer (km/h or mph + km/h) 4- Rheostat illumination button (Type 1)

® p. 5-02 5- Multi information display switch (Type

2) ® p. 5-18

CAUTION

When driving, watch the tachometer to make

sure that the engine speed indication does

not rise into the red zone (excessive engine

rpm).

Meter illumination control Type 1

Each time you press the rheostat illumination button, there is a sound and the brightness of the instruments changes.

1- Brightness level 2- Rheostat illumination button

NOTE

You can adjust to 8 different levels respectively for when the position lamps are illuminated and when they are not.

If the vehicle is equipped with the automatic lamp control, when the lamp switch is in a position other than the “OFF” position, the meter illumination switches automatically to the adjusted brightness, depending on the brightness outside the vehicle.

Instruments

5-02

OKTE20E1

Instruments and controls

Page 93

NOTE

The brightness level of the instruments is stored when the ignition switch is turned off or the operation mode is put in OFF.

If you press and hold the button for about 2 seconds or more when the position lamps are illuminated, the brightness level changes to the maximum level. Pressing and holding the button for about 2 seconds or more again returns the brightness level to the previous level.

Multi information display Type 1

Always stop the vehicle in a safe place before operating. The following information is included on the multi information display: warnings, odometer, tripmeter, average and momentary fuel consumption, average speed etc.

[When the ignition switch or the operation mode is OFF]

mark display ® p. 5-07

2- Information screen ® p. 5-05

Interrupt display screen ® p. 5-06 3- Odometer ® p. 5-08 4-

“ ” or “ ” mark indicator ® p. 5-06

[When the ignition switch or the operation mode is ON]

1- Off Road mode indicator display*

® p. 6-53

2- Drive mode indicator display* (Vehicles

with Easy Select 4WD) ® p. 6-43 (Vehicles with Super Select 4WD II) ® p. 6-49

mark display ® p. 5-07

4- Forward Collision Mitigation system

(FCM) OFF indicator display* ® p. 6-94 Ultrasonic misacceleration Mitigation System (UMS) OFF indicator display* ® p. 6-105

Multi information display - Type 1

5-03

OKTE20E1

Instruments and controls

Page 94

5- Lane Departure Warning (LDW) indica-

tor display* ® p. 6-112 6- Information screen ® p. 5-05 7- Engine coolant temperature display

® p. 5-07 8- Odometer ® p. 5-08 9- Cruise control indicator display

® p. 6-80

10- Speed limiter indicator display*

® p. 6-84

11-

“

” or “ ” mark indicator ® p. 5-06

12- Gearshift indicator display (vehicles

with M/T) ® p. 6-29

13- Selector lever position indicator display

(vehicles with A/T) ® p. 6-33

14- Fuel remaining display ® p. 5-07 15- Outside temperature display ® p. 5-08 16- Auto Stop & Go indicator display*

® p. 6-25

Auto Stop & Go OFF indicator display*

® p. 6-28

NOTE

The fuel units, outside temperature units,

display language, and other settings can be

changed.

Refer to “Changing the function settings” on

page 5-13.

Multi information display switch

Each time the multi information display switch is operated, the buzzer sounds and the multi information display changes between information such as warnings, tripmeter, average and momentary fuel consumption, distance range etc. It is also possible to change elements such as the language and units used on the multi information display by operating the multi information display switch.

NOTE

Each time the multi information display back switch is operated, the buzzer sounds and the multi information display return to the position before pressing the multi information display switch.

Multi information display - Type 1

5-04

OKTE20E1

Instruments and controls

Page 95

Information screen (when the ignition switch or the operation mode is OFF)

Each time you lightly press the multi information display switch, the display screen switches in the following order.

*1: When there is no warning display *2: When there is a warning display

Tripmeter ® p. 5-08

Tripmeter

® p. 5-08

3- Auto Stop & Go (AS&G) monitor*

® p. 5-12

ECO score display ® p. 5-12 4- Service reminder ® p. 5-09 5- Redisplay of a warning display screen

® p. 5-06

Information screen (when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON)

When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the display screen switches in the following order.

*: When the inspection time has arrived

1. Screen when the ignition switch or the operation mode is OFF

2. System check screen ® p. 5-10

3. Screen when the ignition switch or the operation mode is ON

4. Service reminder ® p. 5-09

Information screen (when the ignition switch or the operation mode is ON)

Each time you lightly press the multi information display switch, the display screen switches in the following order.

*1: When there is no warning display *2: When there is a warning display

Tripmeter ® p. 5-08

Multi information display - Type 1

5-05

OKTE20E1

Instruments and controls

Page 96

Tripmeter ® p. 5-08

3- Driving range display ® p. 5-10

ECO drive assist display ® p. 5-12

4- Average fuel consumption display

® p. 5-11 ECO drive assist display ® p. 5-12

5- Average speed display ® p. 5-11

Momentary fuel consumption display ® p. 5-11

6- Auto Stop & Go (AS&G) monitor*

® p. 5-12 ECO score display ® p. 5-12

7- 2WD/4WD operation indicator display*

(Vehicles with Easy Select 4WD) ® p. 6-43 (Vehicles with Super Select 4WD II)

® p. 6-49 8- Service reminder ® p. 5-09 9- Function setting screen ® p. 5-13

10- Redisplay of a warning display screen

® p. 5-06

NOTE

While driving, the service reminder are not

displayed even if you operate the multi in-

formation display switch. Always stop the

vehicle in a safe place before operating.

NOTE

While driving, the function setting screen is not displayed even if you operate the multi information display switch. Always stop the vehicle in a safe place before operating and firmly apply the parking brake and put the gearshift lever into the “N” (Neutral) position (M/T) or the selector lever into the “P” (PARK) position (A/T). Refer to “Changing the function settings” on page 5-13.

When there is information to be announced, such as a system fault, the buzzer sounds and the screen display is switched. Refer to “Interrupt display screen” on page 5-06.

Interrupt display screen

Warning display

When there is information to be announced, such as a system fault, the buzzer sounds and the information screen is switched to the warning display screen. Refer to the warning list and take the necessary measures. Refer to “Warning display list” on page 5-26. When the cause of the warning display is eliminated, the warning display goes out automatically.

To return to the screen displayed before the warning display

Even if the cause of the warning display is not eliminated, you can return to the screen that was displayed before the warning display. If you press the multi information display switch, the display screen switches to the screen that was displayed before the warning display and the

mark (A) is displayed.

If you want to switch the display

Warning display screens with a “ ” or “ ” mark displayed in the upper right of the screen can be switched. If you want to switch the display, press the multi information display switch as follows. “

”: Press lightly. “ ”: Press for approximately 2 seconds or more.

Multi information display - Type 1

5-06

OKTE20E1

Instruments and controls

Page 97

Redisplay of a warning display screen

When the mark is displayed, if you lightly press the multi information display switch a few times, the warning display screen you switched from is redisplayed.

Other interrupt displays

The operation status of each system is displayed on the information screen. Refer to the appropriate page in the warning display list for further details. Refer to “Other interrupt displays” on page 5-45.

mark display

This is displayed when you press the multi information display switch and return from the warning display screen to the previous screen. This mark is also displayed if there is another warning other than the one displayed. When the cause of the warning display is eliminated, the

mark goes out automatical-

ly.

NOTE

When the mark is displayed, the warning display screen can be redisplayed on the information screen. Refer to “Information screen (when the ignition switch or the operation mode is OFF)” on page 5-05. Refer to “Information screen (when the ignition switch or the operation mode is ON)” on page 5-05.

Engine coolant temperature display

This indicates the engine coolant temperature. If the coolant becomes hot, “ ” will blink. Pay careful attention to the engine coolant temperature display while you are driving.

CAUTION

If the engine is overheating, “ ” will blink. In this case, the bar graph is in the red zone. Immediately park the vehicle in a safe place and take the required measures. Refer to “Engine overheating” on page 8-09.

Fuel remaining display

This displays the amount of fuel remaining.

F (1) - Full E (0) - Empty

NOTE

It may take several seconds to stabilise the display after refilling the tank.

If fuel is added with the ignition switch or the operation mode is in ON, the fuel gauge may incorrectly indicate the fuel level.

The arrow (A) indicates that the fuel tank filler door is located on the left side of the body.

Multi information display - Type 1

5-07

OKTE20E1

Instruments and controls

Page 98

Fuel remaining warning display

When the fuel is reduced to approximately 10 litres, the information screen switches to the interrupt display of the fuel remaining warning display, and the “ ” mark (B) on the fuel remaining display flashes slowly (approximately once per second). After a few seconds, the information screen returns from the fuel remaining warning display to the previous screen. If the remaining fuel level is reduced further, the information screen switches to the fuel remaining warning display and the “

” mark (B) on the fuel remaining display flashes quickly (approximately twice per second).

CAUTION

Do not drive with an extremely low fuel level; running out of fuel could cause damage to the fuel system.

NOTE

On inclines or curves, the display may be incorrect due to the movement of fuel in the tank.

Outside temperature display

This shows the temperature outside the vehicle.

NOTE

The display setting can be changed to the preferred units (°C or °F). Refer to “Changing the function settings” on page 5-13.

Depending on factors such as the driving conditions, the displayed temperature may vary from the actual outside temperature.

Odometer

The odometer indicates the distance travelled.

Tripmeter

The tripmeter indicates the distance travelled between two points.

Example usage of tripmeter and tripmeter

It is possible to measure two currently travelled distances, from home using tripmeter

and from a particular point

on the way using tripmeter .

To reset the tripmeter

To return the display to 0, hold down the multi information display switch for approximately 2 seconds or more. Only the currently displayed value will be reset.

Example If tripmeter

is displayed, only tripmeter

will be reset.

NOTE

When disconnecting the battery terminal, the memory of tripmeter and are

cleared, and the display returns to “0”.

Multi information display - Type 1

5-08

OKTE20E1

Instruments and controls

Page 99

Service reminder

Displays the approximate time until the next periodic inspection recommended by MITSUBISHI MOTORS. “---” is displayed when the inspection time has arrived.

NOTE

Depending on the vehicle specifications, the displayed time until the next periodic inspection may differ from that recommended by MITSUBISHI MOTORS. In addition, the display settings for the next periodic inspection time can be modified. To modify the display settings, have it adjusted at a MITSUBISHI MOTORS Authorized Service Point. For more details, contact a MITSUBISHI MOTORS Authorized Service Point.

1. Displays the time until the next periodic inspection.

NOTE

The distance is shown in units of 100 km (100 miles). The time is shown in units of months.

2. This informs you that a periodic inspection is due. Consult a MITSUBISHI MOTORS Authorized Service Point. At that time, when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON, the warning display is displayed for a few seconds on the information screen.

3. After your vehicle is inspected at a MITSUBISHI MOTORS Authorized Service Point, it displays the time until the next periodic inspection.

To reset

The “---” display can be reset while the ignition switch or the operation mode is in OFF. When the display is reset, the time until the next periodic inspection is displayed and the warning display is no longer displayed when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON.

1. When you lightly press the multi information display switch a few times, the information display switches to the service reminder display screen.

2. Press and hold the multi information display switch for approximately 2 seconds or more to display “ ” and make it flash. (If there is no operation for approximately 10 seconds with flashing, the display returns to the previous screen.)

Multi information display - Type 1

5-09

OKTE20E1

Instruments and controls

Page 100

3. Lightly press the multi information display switch while the icon is flashing to change the display from “---” to “CLEAR”. After this, the time until the next periodic inspection will be displayed.

CAUTION

The customer is responsible for making sure that periodic inspection and maintenance are performed. Inspections and maintenance must be performed to prevent accidents and malfunctions.

NOTE

“---”display cannot be reset when the ignition switch or the operation mode is in ON.

NOTE

When “---” is displayed, after a certain distance and a certain period of time, the display is reset and the time until the next periodic inspection is displayed.

If you accidentally reset the display, consult a MITSUBISHI MOTORS Authorized Service Point.

System check screen

When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the system check screen is displayed for approximately 4 seconds. If there is no fault, information screen (when the ignition switch or the operation mode is ON) is displayed. If there is a fault, the screen changes to warning display. Refer to “Warning display list” on page 5-26.

NOTE

The system check screen display varies depending on the customer’s equipment.

Driving range display

This displays the approximate driving range (how many more kilometres or miles you can drive). When the driving range falls below approximately 50 km (30 miles), “---” is displayed. Refuel as soon as possible.

NOTE

The driving range is determined based on the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a rough guideline.

When you refuel, the driving range display is updated. However, if you only add a small amount of fuel, the correct value will not be displayed. Fill with a full tank whenever possible.

On rare occasions, the value displayed for the driving range may change if you are parked on an extremely steep incline. This is due to the movement of fuel in the tank and does not indicate a malfunction.

Multi information display - Type 1

5-10

OKTE20E1

Instruments and controls

Mitsubishi Triton (2018), Triton (2019) Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Foreword

Information for station service

Table of contents

Instruments and Controls (Driver’s area)

Instruments and Controls

Interior

Exterior - front

Exterior - rear

Quick guide

Locking and unlocking the doors

Keyless entry system*

Keyless operation system*

Around the driver’s seat

1-Electric remote-controlled outside rear-view mirrors*

2-Engine switch*

3-Combination headlamps

3-Turn-signal lever

4-Steering wheel height and reach adjustment

5-Wiper and washer switch

6-Electric window control*

7-Fuel tank filler door release lever*

Automatic transmission Sports Mode 6A/T

Selector lever operation

Selector lever positions

“P” PARK

“R” REVERSE

“N” NEUTRAL

“D” DRIVE

4-wheel drive operation

Multi information display

Type 1

Type 2

General information

Fuel selection

Filling the fuel tank

Fuel tank capacity

Refueling

Entering or leaving the vehicle*

Installation of accessories

Important points!

Modification/alterations to the electrical or fuel systems

Genuine parts

Safety and disposal information for used engine oil

Protect the environment

Disposal information for used batteries

Event Data Recording

Locking and unlocking

Keys

Key number tag

Electronic immobilizer (Anti-theft starting system)

Keyless entry system*

To lock

To unlock

Operation of the Dead Lock System*

To retract

To extend

Procedure for replacing the key battery

Keyless operation system*

Operating range of the keyless operation system

Operating range for locking and unlocking the doors

To operate using the keyless operation function

Locking the doors

Unlocking the doors

Operation confirmation when locking and unlocking

To lock/unlock without using the keyless operation function

Emergency key

Locking and unlocking the door

Operation of the Dead Lock System

Warning activation

Doors

To lock or unlock with the key

To lock or unlock from inside the vehicle

To lock without using the key

To open or close the rear door (Club cab)

Central door locks

Driver’s door with key