Mitsubishi Q64TD, Q64TDV-GH, Q64TD-U-H-JE User Manual
Thermocouple Input Module
Channel Isolated Thermocouple
/Micro Voltage Input Module
MITSUBISHI
General-Purpose PROGRAMMABLE LOGIC CONTROLLER
User’s Manual
(Hardware)
Q64TD
Q64TDV-GH
Thank you for purchasing the Mitsubishi general-purpose
programmable logic controller MELSEC-Q series.
Prior to use, please read this manual thoroughly and
familiarize yourself with the product
MODEL Q64TD-U-H-JE
MODEL
CODE
13JT30
IB(NA)-0800155-B(0201)MEE
© 2000 MITSUBISHI ELECTRIC CORPORATION
A - 1
SAFETY PRECAUTIONS
(Read these precautions before using.)
When using Mitsubishi equipment, thoroughly read this manual and the
associated manuals introduced in this manual. Also pay careful attention to
safety and handle the module properly.
These SAFETY PRECAUTIONS classify the safety precautions into two
categories: “DANGER” and “CAUTION”.
DANGER
CAUTION
Procedures which may lead to a dangerous condition and
cause death or serious injury, if not carried out properly.
Procedures which may lead to a dangerous condition and
cause superficial to medium injury, or physical damage
only, if not carried out properly.
Depending on circumstances, procedures indicated by CAUTION may also
be linked to serious results.
In any case, it is important to follow the directions for usage.
Store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
[DESIGN PRECAUTIONS]
DANGER
Do not write data into the "system area" of the buffer memory of intelligent
function modules. Also, do not use any "prohibited to use" signals as an
output signal to an intelligent function module from the PLC CPU.
Writing data into the "system area" or outputting a signal for "prohibited to
use" may cause a PLC system malfunction.
CAUTION
Do not bunch the control wires or communication cables with the main
circuit or power wires, or install them close to each other.
They should be installed 100 mm(3.94 inch) or more from each other.
Not doing so could result in noise that may cause malfunction.
A - 2
[INSTALLATION PRECAUTIONS]
CAUTION
Use the PLC in an environment that meets the general specifications
contained in the CPU user's manual.
Using this PLC in an environment outside the range of the general
specifications may cause electric shock, fire, malfunction, and damage to
or deterioration of the product.
When installing the module, securely insert the module fixing tabs into the
mounting holes of the base module while pressing the installation lever
located at the bottom of the module downward.
Improper installation may result in malfunction, breakdown or the module
coming loose and dropping. Securely fix the module with screws if it is
subject to vibration during use.
Tighten the screws within the range of specified torque.
If the screws are loose, it may cause the module to fallout, short circuits, or
malfunction.
If the screws are tightened too much, it may cause damage to the screw
and/or the module, resulting in fallout, short circuits or malfunction.
Switch all phases of the external power supply off when mounting or
removing the module.
Not ding so may cause electric shock or damage to the module.
Do not directly touch the conductive area or electronic components of the
module. Doing so may cause malfunction or failure in the module.
[WIRING PRECAUTIONS]
CAUTION
Always ground the FG terminal for the PLC.
There is a r isk of electr ic shock or malfunction.
When turning on the power and operating the module after wiring is
completed, always attach the terminal cover that comes with the product.
There is a risk of electric shock if the terminal cover is not attached.
Tighten the terminal screws within the range of specified torque.
If the terminal screws are loose, it may result in short circuits or malfunction.If
the terminal screws are tightened too much, it may cause damage to the screw
and/or the module, resulting in short circuits or malfunction.
Be careful not to let foreign matter such as sawdust or wire chips get inside
the module.They may cause fires, failure or malfunction.
A - 3
[WIRING PRECAUTIONS]
CAUTION
The top surface of the module is covered with protective film to prevent
foreign objects such as cable offcuts from entering the module when wiring.
Do not remove this film until the wiring is complete.
Before operating the system, be sure to remove the film to provide
adequate ventilation.
Always place the thermocouple at least 100mm (3.94inch) away from the
main circuit cables and AC control lines. Fully keep it away from highvoltage cables and circuits which include harmonics, such as an inverter's
load circuit. Not doing so will make the module more susceptible to noises,
surges and inductions.
REVISIONS
The manual number is given on the bottom right of the top cover.
Print Date
Manual Number Revision
Nov.,2000 IB (NA)-0800155-A First edition
Jan.,2002 IB (NA)-0800155-B Model Q64TDV-GH was added.
Addition
Section2.2
Correction
About the Manuals, Chapter1,
Section2.1,Chapter4,Section5.1
Section5.2
,
Section5.3,Chapter6
This manual confers no industrial property rights or any rights of any other kind, nor
dose it confer any patent licenses. Mitsubishi Electric Corporation cannot be held
responsible for any problems involving industrial property rights which may occur as
a result of using the contents noted in this manual.
© 2000 MITSUBISHI ELECTRIC CORPORATION
A - 4
CONTENTS
SAFETY PRECAUTIONS..............................................................................A-1
REVISIONS...................................................................................................A-3
CONTENTS...................................................................................................A-4
About the Manuals.........................................................................................A-5
Conformance to the EMC Directive/Low Voltage Directive............................A-5
1. OVERVIEW...................................................................................................1
2. SPECIFICATIONS.........................................................................................1
2.1 Specifications of Q64TD..........................................................................1
2.1.1 Performance specifications.............................................................1
2.1.2 Usable thermocouples and measured temperature range
accuracies.......................................................................................2
2.2 Specifications of Q64TD V -GH.................................................................3
2.2.1 Performance specifications.............................................................3
2.2.2 Usable thermocouples and measured temperature range
accuracies ......................................................................................5
2.2.3 Micro voltage input range and accuracies.......................................5
3. LOADING AND INSTALLATION....................................................................6
3.1 Handling Instructions...............................................................................6
3.2 Installation Envi ronment ..........................................................................6
4. NAMES AND SETTINGS OF THE PARTS....................................................7
5. WIRING.........................................................................................................8
5.1 Wiring Instruc tions...................................................................................8
5.2 External Wiring........................................................................................8
5.3 Intelligent Function Module Switch Setting.............................................10
6. OUTLINE DRAWINGS ................................................................................11
A - 5
About the Manuals
The following manuals are related to this product.
Referring to this list, please request the necessary manuals.
Detailed manual
Manual Name
Manual Number
(Model Code)
Thermocouple Input Module , Channel Isolated
Thermocouple/Micro Voltage Input Module User's
Manual
Q64TD/Q64TDV-GH/GX Configurator-TI (SW1D5CQTIU-E)
SH-080141
(13JR30)
Conformance to the EMC Directive/Low Voltage Directive
For details on making Mitsubishi PLC conform to the EMC directive and low
voltage instruction when installing it in your product, please see Chapter 3,
"EMC Directive and Low Voltage Instruction" of the User's Manual (Hardware)
of the PLC CPU to use.
The CE logo is printed on the rating plate on the main body of the PLC that
conforms to the EMC directive and low voltage instruction.
Loading...