CC-Link Ver.1.10
FX2N-16CCL-M CC-Link SYSTEM MASTER BLOCK
HARDWARE MANUAL
JY992D93201C
This manual contains text, diagrams and explanations which will guide the reader in the correct installation
and operation of the FX
2N
-16CCL-M CC-Link SYSTEM MASTER BLOCK. It should be read and
understood before attempting to install or use the unit. Further information can be found in the FX series
PLC hardware manuals.
Guidelines for the safety of the user and protection of the FX2N-16CCL-M CC-Link
SYSTEM MASTER BLOCK
• If in doubt at any stage during the installation of the FX2N-16CCL-M CC-Link SYSTEM MASTER
BLOCK always consult a professional electrical engineer who is qualified and trained to the local
and national standards. If in doubt about the operation or use of the FX
2N
-16CCL-M CC-Link
SYSTEM MASTER BLOCK please consult the nearest Mitsubishi Electric distributor.
• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to
understanding the text, not to guarantee operation. Mitsubishi Electric will accept no
responsibility for actual use of the product based on these illustrative examples.
• Owing to the very great variety in possible application of this equipment, you must satisfy
yourself as to its suitability for your specific application.
Note’s on the symbology used in this manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the user’s personal safety and protect the integrity of the equipment.
Whenever any of the following symbols are encountered, its associated note must be read and
understood. Each of the symbols used will now be listed with a brief description of its meaning.
Hardware warnings
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property damage.
1. INTRODUCTION
1.1 Associated Manuals
Manual name Manual number Description
2N
★
FX
-16CCL-M
User’s Manual
1S
★
FX
/FX1N/FX2N/FX
2NC
Programming Manual II
3U
FX
/FX
3UC
★
Programming Manual
1N
✩
FX
Hardware Manual
2N
✩
Hardware Manual
FX
3U
✩
FX
Series User’s
Manual
- Hardware Edition
2NC
✩
Hardware Manual
FX
3UC
✩
FX
Series User’s
Manual
- Hardware Edition
2N
✩
FX
-32CCL
User’s Manual
★
: Indispensable manual
✩
: Manual required depending on equipment used
JY992D93101
(sent separately)
JY992D88101
(sent separately)
JY997D16601
(sent separately)
JY992D89301
(packed with product)
JY992D66301
(packed with product)
JY997D16501
(sent separately)
JY992D76401
(packed with product)
JY997D28701
(sent separately)
JY992D71801
(packed with product)
Describes programming and handling of the CC-
2N
Link master block FX
-16CCL-M.
Explains the instructions available to the FX
FX
1N
/FX2N/FX
2NC
Series PLC.
Explains the instructions available to the FX
3UC
Series PLC.
FX
Describes hardware specifications, wiring and
mounting of the FX
1N
Series PLC.
Describes the contents related to the hardware
such as specifications, wiring and mounting of the
2N
Series PLC.
FX
Describes the hardware specifications, wiring and
3U
mounting of the FX
Series PLC.
Describes the hardware specifications, wiring and
2NC
mounting of the FX
Series PLC.
Describes the hardware specifications, wiring and
3UC
mounting of the FX
Series PLC.
Describes programming and handling of the CC-
2N
Link interface block FX
-32CCL.
1S
/
3U
/
1.2 Overview
The CC-Link master block FX2N-16CCL-M is a special extension block which assigns an FX Series PLC
as the master station of the CC-Link system.
1) Remote I/O stations and remote device stations can be connected to the master station (FX Series
PLC).
Master station : Station which controls the data link system
Remote I/O station : Remote station which handles only bit information
Remote device station : Remote station which handles both bit information and word information
2) By using the CC-Link interface block FX
remote device stations to configure a simple distributed system.
Partner manufacturer’s
product
2N
-32CCL, two or more FX Series PLCs can be connected as
CC-Link master block
FX
-16CCL-M
2N
Remote I/O station
Remote I/O station
FX1N/FX2N/FX
Series PLC
2NC
Remote device station
FX0N/FX1N/FX2N/FX
Series PLC
2NC
/FX3U/FX
1.3 Dimensions and Setting
Dimensions: mm (inches) MASS (Weight): 0.4 kg (0.88 lbs)
87(3.43)
MITSUBISHI
10)
85(3.34)
75(2.95)
2-f4.5
FX2N-16CCL-M
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
POWER
90(3.5)
80(3.15)
E
SW
M/S
R
PRM
R
TIME
O
LINE
R
SD
RD
/FX
3
U
/FX
3
UC
Remote device station
CC-Link interface block
3UC
FX
-32CCL
2N
24+
24-
FG
9)
8)
12)
SLD DG
DA
RUN
FX2N-16CCL-M
ERR.
MST
TEST1
1)
TEST2
STATION
L RUN
3
2
4
1
NO.
5
L ERR.
0
6
´10
9
7
8
3
2
POWER
4
1
5
0
6
1
´
9
7
8
5
4
6
3
7
2
8
1
9
0
A
F
MODE
B
E
C
D
3
2
B RATE
4
1
5
156K
0
0
6
9
625K
7
1
8
2.5M
2
5M
3
ON
12345678
10M
4
DB
SW
ONOFF
1
--
2
---
SW
3
-
M/S
HLD
4
CLR
PRM
--
5
6
-
-
TIME
7
----
LINE
8
SD
RD
4)
2)
5)
11)
6)
7)
E
R
R
O
3)
R
9(0.35)
Number Name Description
1) LED
indicators 1
RUN
ERR.
MST
TEST 1
TEST 2
L RUN
L ERR
LED
name
RUN
ERR.
Description
ON : Module is normal.
OFF: Watchdog time error has occurred.
Indicates the communication status with the
stations set in the parameters.
ON : Communication error has
occurred in all stations.
Flashing : Communication error has
occurred in some stations.
MST ON : Set as the master station
TEST1 Test result indication
TEST2 Test result indication
L RUN
ON : Data link is being executed
(host station).
ON : Communication error has
occurred (host station).
L ERR.
Flashing : The settings of the switches 4) to
7) were changed while the power
was ON.
2) Power indictor POWER ON : 24V DC is supplied from the outside.
Inside of top cover
LED status
Normal Error
ON OFF
OFF
ON OFF
OFF except during
ON OFF
OFF
ON OFF
ON or
flashing
test
ON or
flashing
Number Name Description
3) LED
indicators 2
SW
M/S
PRM
TIME
LINE
SD
RD
SW ON : Switch setting error has occurred. OFF ON
ON : The master station is already present
M/S
E
E
R
PRM
R
R
R
O
TIME
O
R
R
LINE
in the same line.
ON : Parameter setting error has occurred.
ON : Data link watchdog timer errors has
occurred (error in all stations).
ON : The cable is broken or the
transmission route has been affected
by noise, etc.
SD ON : Data is being transmitted.
RD ON : Data is being received.
4)
Station
Sets the station number of the module. (Default setting at shipment: 00)
number setting
switch
STATION NO.
×
10
1
×
<Setting range>
2N
00 (because the FX
3
4
2
1
5
If "65" or larger number is set, the "SW" and "L ERR." LED indicators turn ON.
0
6
9
7
8
3
4
2
1
5
0
6
9
7
8
-16CCL-M is dedicated to the master station)
OFF ON
OFF ON
OFF ON
OFF ON
ON OFF
ON OFF
5) Mode setting
switch
Sets the operation status of the module. (Default setting at shipment: 0)
Number Name Description
0 Online Sets connection to data link.
MODE
4
3
2
1
0
F
E
D
1 (Unusable)
5
6
7
8
9
A
B
C
2 Offline Sets disconnection from data link.
3 Line test 1 Refer to USER’S MANUAL.
⎯
4 Line test 2 Refer to USER’S MANUAL.
Parameter
5
verification test
Refer to USER’S MANUAL.
6 Hardware test Refer to USER’S MANUAL.
7 (Unusable) Setting error (The SW LED indicator turns ON.)
8 to A (Unusable) Cannot be set because it is already used inside.
B to F (Unusable) Setting error (The SW LED indicator turns ON.)
6) Transmission
speed setting
switch
B RATE
0
156K
1
625K
2
2.5M
3
5M
4
10M
Sets the transmission speed of the module. (Default setting at shipment: 0)
Number Setting contents
0 156 kbps
1 625 kbps
3
2
1
0
9
8
2 2.5 Mbps
4
5
6
7
3 5 Mbps
4 10 Mbps
5 to 9 Setting error (The SW and L ERR. LED indicators turn ON.)
7) Condition
setting switch
ON
OFF
SW
⎯
⎯
1
⎯
⎯
2
⎯
⎯
3
HLD
CLR
4
⎯
⎯
5
⎯
⎯
6
⎯
⎯
7
⎯
⎯
8
Sets the operation condition. (Default setting at shipment: All OFF)
Number Setting description
ON
12345678
SW1 to
SW3
(Unusable) Always OFF
SW4 Input data status in data link faulty station
SW5 to
SW8
(Unusable) Always OFF
Switch status
ON OFF
Keep
(HLD)
Clear
(CLR)
8) Terminal block Connects dedicated CC-Link cables to enable data link. For the connection
method, refer to Section 2.3.
SLD DG DA DB
The terminals SLD and FG are connected inside.
M3.5 Screw
9) Terminal block Connects the power supply to operate the master block.
24+
24-
FG
10) Extension
cable
M3 Screw
Connects the PLC.
11) Next step
extension
Connects extension equipment.
connector
12) DIN rail
mounting
DIN46277: DIN rail mounting groove of 35 mm (1.38") in width
groove
Loading...