Mitsubishi GT25-05UCOV, GT25-UCOV, GT21-WUCOV User Manual

GOT2000 Series

WAR NIN G

CAUTION

CAUTION

CAUTION

CAUTION

3)

4)

1)

2)

51.5

11.5

5.1

Unit: mm (inch)

(0.45) (0.20)

(2.03)

USB Environmental Protection
Cover

User's Manual

GT25-UCOV
GT21-WUCOV
GT25-05UCOV

Thank you for purchasing Mitsubishi Electric Graphic Operation
Te rm i na l.

Prior to use, please read both this manual and detailed
manual thoroughly to fully understand the product.

MODEL GT25-UCOV-U-JE

MODEL

CODE

IB(NA)-0800501-E(2004)MEE

© 2013 MITSUBISHI ELECTRIC CORPORATION

lSAFETY PRECAUTIONSl

(Always read these precautions before using this equipment.)

Before using this product, please read this manual a nd the relevant manuals
introduced in this manual carefully and pa y full attention to safety to handle the
product correctly.
The precautions given in this manual are conc erned with this product.
In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Indicates that incorrect handling may ca use hazardous
conditions, resulting in death or seve re injury.

Indicates that incorrect handling may ca use hazardous
conditions, resulting in medium or sl ight personal injury
or physical damage.

Note that the CAUTION level may lead to a serious accident accordin g to the
circumstances.
Always follow the precautions of both levels beca use they are important to
personal safety.
Please save this manual to make it a ccessible when required and always forward it
to the end user.

[INSTALLATION PRECAUTIONS]

1D7MI2

[DISPOSAL PRECAUTIONS]

 Dispose of this product as industrial waste.

[TRANSPORTATION PRECAUTIONS]

 When fumigants that contain halogen materials such as fluo rine, chlorine,

bromine, and iodine are used for disinfectin g and protecting wooden
packaging from insects, they cause malf unction when entering our products.
Please take necessary precautions to ensur e that remaining materials from
fumigant do not enter our products, or treat packaging with methods other
than fumigation (heat method).
Additionally, disinfect and protect wood from insects before packing produc ts.

Manuals

The following shows manuals relevant to this pr oduct.

GOT2000 Series User’s Manual (Hardware)

For detailed manuals and relevant manuals, refer to the e-Manual or PDF
manuals stored in the DVD-ROM for the screen design software used.

The latest manuals are also available from MI TSUBISHI ELECTRIC FA Global
Website (www.MitsubishiElectric.com/fa).

Referenced Standard: GB/T15969.2
(Requirement of Chinese standardized law)

Packing List

After unpacking the box, check that the following products are included.

·

GT25-UCOV
GT21-WUCOV
GT25-05UCOV

Manual name Manual number (Model code )

Model Product Quantity

series USB environmental protec tion

GOT2000
cover

Fixing screw (M3 x 6) 1
GOT2000 Series USB Environmental Protection

Cover User's Manual (This manual)

SH-081194ENG (1D7MJ5)

1

1

1. OVERVIEW

This user's manual describes the USB environmental protection cover of the
GOT2000 series (hereinafter referred to as the US B environmental protection
cover).
The USB environmental protection cover is fo r protection of the USB interface.

The following table shows the USB environmental pr otection cover models and
applicable GOTs.

Model Screen sizes for the applicable GOTs

GT25-UCOV

GT21-WUCOV

GT25-05UCOV GT2705-VTBD

The USB environmental protection cover is us ed to make the USB interface
complaint with the protective structure IP67F

*1: The suffix "F" of IP67F is a symbol that indicates protection rate again st oil.

It is described in the Appendix of Japanese Industrial Standard JIS C 0920.

The following GOTs with the USB interface on their front faces

· 15" models

· 12.1" models

· 10.4" models

· 8.4" models

The following GOTs with the USB interface on their front faces

· 10.1" wide models

· 7" wide models

· GT2505-VTBD

*1

.

2. SPECIFICATIONS

The following shows the performance specifi cations of the USB environmental
protection cover.
The general specifications of the USB en vironmental protection cover are the same
as those of the GOT.
For the general specifications of the GOT, refer to the GOT2000 Series User's
Manual (Hardware).

Item Description

Protective structure*1 IP67F

Weight 0.005 kg

*1: The USB interface is IP67F-rated when the USB environme ntal protection

cover is installed to the GOT.
To conform to IP67F, close the USB environmental protection cover by pushing
in the [PUSH] mark or [PULL] mark firmly to lock the cover.
(The USB interface is IP2X-rated when the USB environmental protection cover
is open.)

3. EXTERNAL DIMENSIONS

3.1 GT25-UCOV

1)

2)

3)

66.1
(2.60)

4)

15.7

(0.62)

No. Name Description

1) Hinge

2) Hinge projection Hinge projection to be fitted in the GOT guid ing hole

3) Packing Packing for protecting the USB interface

4) Latch

7

(0.28)

Hinge for opening or closing the USB environmental
protection cover

Latch for fixing or opening the USB environmental
protection cover

Unit: mm (inch)

3.2 GT21-WUCOV

No. Name Description

1) Hinge

2) Hinge projection Hinge projection to be fitted in the GOT guiding hole

3) Packing Packing for protecting the USB interface

4) Latch

Hinge for opening or closing the USB environmental
protection cover

For locking or unlocking th e USB environmental
protection cover

3.3 GT25-05UCOV

1)

2)

3)

71

(2.80)

4)

15.5

(0.61)

No. Name Description

1) Hinge

2) Hinge projection Hinge projection to be fitted in the GOT guiding hole

3) Packing Packing for protecting the USB interface

4) Latch

7

(0.28)

Hinge for opening or closing the USB environmental
protection cover

Latch for fixing or opening the USB environmental
protection cover

Unit: mm (inch)



Make sure to securely fix the USB environmental protection cover onto the GOT using
fixing screws and tighten the screws in the specified torque of 0.36 N•m to 0.48 N•m.
Loose tightening may cause the USB environmental protection cover to drop off and/
or the GOT to fail or malfunction.
Overtightening may damage and drop screws and/or the USB environmental
protection cover.



When closing the USB environmental protection cover, fix the cover to the GOT by
pushing the [PUSH] or [PULL] mark on the latch firmly to comply with the protective
structure.

4. INSTALLATION AND REMOVAL

4.1 Installing the USB Environmental Protection
Cover

4.1.1 GT25-UCOV, GT25-05UCOV

The installation procedure for the USB environmental protection cover is explained
using GT2712.

1) Get up the hinge of the USB environmental protecti on cover.

2) Align the hinge projection of the USB environmental protection cover on the
guiding hole of the GOT.

Put a supplied fixing screw through the hinge h ole of the USB environmental

protection cover.

Fixing screw

3) Tighten the fixing screw in the specified torque range (0.36 N•m to 0.48 N•m) to

fix the cover to the GOT.

4) When you do not use the USB interface, close the USB environmental
protection cover by pushing in the [PUSH] mark on the c over firmly.

5) To use the USB interface, open the USB environmental protection cover by
pushing the [PUSH] mark on the cover.

4.1.2 GT21-WUCOV

The installation procedure for the USB environmental protection cover is explained
using GT2510-WX.

1) Get up the hinge of the USB environmental protecti on cover.

2) Align the hinge projection of the USB environmental protection cover on the
guiding hole of the GOT.

Put a supplied fixing screw through the hinge h ole of the USB environmental

protection cover.

Fixing screw

3) Tighten the fixing screw in the specified torque range (0.36 N•m to 0.48 N•m) to

fix the cover to the GOT.

4) When you do not use the USB interface, close the USB environmental
protection cover by pushing in the [PULL] mark on t he cover firmly.
When you close the USB environmental protection c over, make sure that the
latch is fully retracted into the cover body.
Otherwise, the USB environmental protection cove r may get damaged.

5) To use the USB interface, unlock the USB environmental protection cover by
sliding its latch and then open the cover.

4.2 Removing the USB Environmental
Protection Cover

Perform the reverse procedure of installation for removing the USB environmental
protection cover.

5. PRECAUTIONS FOR USE

1) When the USB environmental protection cover is closed, the USB interface is
IP67F-rated.

In this case, the USB environmental protection c over must be locked into

position by pushing in the [PUSH] mark or [PULL] ma rk firmly.

2) The USB environmental protection cover is a consumable product.

Check the cover periodically. When the cover has damage, heavy soil, a nd

others, replace the cover.

Warranty

Mitsubishi Electric will not be held liable for damage caused by
factors found not to be the cause of Mitsubishi Electric; machine
damage or lost profits caused by faults in the Mitsubishi Electric
products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi Electric;
damages to products other than Mitsubishi Electric products; and to
other duties.

For safe use

• This product has been manufactured as a general-purpose part for
general industries, and has not been designed or manufactured to
be incorporated in a device or system used in purposes related to
human life.

• Before using the product for special purposes such as nuclear
power, electric power, aerospace, medicine or passenger
movement vehicles, consult with Mitsubishi Electric.

• This product has been manufactured under strict quality control.
However, when installing the product where major accidents or
losses could occur if the product fails, install appropriate backup or
failsafe functions in the system.

Country/Region Sales office/Tel

USA Mitsubishi Electric Automation, Inc.

Brazil Mitsubishi Electric do Brasil Comercio e Servicos Ltda.

Mexico Mitsubishi Electric Automation, Inc. Mexico Branch

Germany Mitsubishi Electric Europe B.V. German Branch

UK Mitsubishi Electric Europe B.V. UK Branch

Italy Mitsubishi Electric Europe B.V. Italian Branch

Spain Mitsubishi Electric Europe B.V. Spanish Branch

France Mitsubishi Electric Europe B.V. French Branch

Czech Mitsubishi Electric Europe B.V. Czech Branch

Turkey Mitsubishi Electric Turkey A.S. Umraniye Branch

Poland Mitsubishi Electric Europe B.V. Polish Branch

Russia Mitsubishi Electric (Russia) LLC St. Petersburg Branch

South Africa Adroit Technologies

China Mitsubishi Electric Automation (China) Ltd.

Taiwan SETSUYO ENTERPRISE CO., LTD.

Korea Mitsubishi Electric Automation Korea Co., Ltd.

Singapore Mitsubishi Electric Asia Pte. Ltd.

Thailand Mitsubishi Electric Factory Automation (Thailand) Co., Ltd.

Indonesia PT. Mitsubishi Electric Indonesia

Vietnam Mitsubishi Electric Vietnam Company Limited

India Mitsubishi Electric India Pvt. Ltd. Pune Branch

Australia MITSUBISHI ELECTRIC AUSTRALIA PTY. LTD.

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry
of Economy, Trade and Industry for service transaction permission.

500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A.
Tel: [phone]

Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP, Brazil
Tel: [phone]

Boulevard Miguel de Cervantes Saavedra 301, Torre Norte Piso 5, Ampliacion Granada,
Miguel Hidalgo, Ciudad de Mexico, Mexico, C.P.11520
Tel: [phone]

Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany
Tel: [phone]

Travellers Lane, UK-Hatfield, Hertfordshire, AL10 8XB, U.K.
Tel: [phone]

Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7,
20864 Agrate Brianza (MB), Italy
Tel: [phone]

Carretera de Rubi, 76-80-Apdo. 420, E-08190 Sant Cugat del Valles (Barcelona), Spain
Tel: [phone]

25, Boulevard des Bouvets, 92741 Nanterre Cedex, France
Tel: [phone]

Pekarska 621/7, 155 00 Praha 5, Czech Republic
Tel: [phone]

Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey
Tel: [phone]

ul. Krakowska 48, 32-083 Balice, Poland
Tel: [phone]

Piskarevsky pr. 2, bld 2, lit "Sch", BC "Benua", office 720; 195027 St. Petersburg, Russia
Tel: [phone]

20 Waterford Office Park, 189 Witkoppen Road, Fourways, South Africa
Tel: [phone]

Mitsubishi Electric Automation Center, No.1386 Hongqiao Road, Shanghai, China
Tel: [phone]

6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan
Tel: [phone]

7F to 9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu,
Seoul 07528, Korea
Tel: [phone]

307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943
Tel: [phone]

12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road,
Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand
Tel: [phone] to 31

Gedung Jaya 8th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia
Tel: [phone]

11th & 12th Floor, Viettel Tower B, 285 Cach Mang Thang 8 Street, Ward 12,
District 10, Ho Chi Minh City, Vietnam.
Tel: [phone]

Emerald House, EL-3, J Block, M.I.D.C., Bhosari, Pune - 411026, Maharashtra, India
Tel: [phone]

348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W 2116, Australia
Tel: [phone]

Specifications subject to change without notice.
Printed in Japan, April 2020.