Mitsubishi GT25-05PCO-2, GT25-05PCO, GT21-07WPCO, GT21-10WPCO, GT20-15PCO User Manual

...

GOT2000 Series

WARNING

CAUTION

WAR NING

CAUTION

Protective Cover for Oil for GT27/GT25/GT23/GT2107

User's Manual

GT20-15PCO GT25-05PCO GT20-12PCO GT25-05PCO-2 GT20-10PCO GT25T-07WPCO GT20-08PCO GT21-10WPCO GT21-07WPCO

Thank you for choosing Mitsubishi Electric Graphic Operation Terminal (GOT).

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL GT20/GT25-PCO-U-JE

MODEL

CODE

IB(NA)-0800498-E(1903)MEE

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product , please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are conc erned with this product. In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

Note that the CAUTION level may lead to a serious accident according to the circumstances. Always follow the precautions of both levels b ecause they are important to personal safety. Please save this manual to make it accessible when required and always forward it to the end user.

1D7MH8

[MOUNTING PRECAUTIONS]



Be sure to shut off all phases of the exte rnal power supply used by the system before mounting or removing the GOT main unit to/from the panel. Not doing so can cause the unit to fail or malfunction.



When mounting the GOT to the control panel, tighten the mounting screws in the specified torque range. Undertightening can cause the GOT to drop, short circuit or malfunction. Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the GOT.

[STARTUP AND MAINTENANCE PRECAUTIONS]



Daily check the protective cover for oil with eyes. When you find extreme dirt or scratches on the surface, immediately replace it with new one. Using the protective cover for oil with decreased visibility may cause malfunction.

[DISPOSAL PRECAUTIONS]

 When disposing of this product, treat it as industrial waste.

[TRANSPORTATION PRECAUTIONS]

 When fumigants that contain halogen materials such as fluo rine, chlorine,

bromine, and iodine are used for disinfectin g and protecting wooden packaging from insects, they cause malfunction when entering our products. Please take necessary precautions to ensure tha t remaining materials from fumigant do not enter our products, or treat packaging with methods other than fumigation (heat method). Additionally, disinfect and protect wood from insects before packing products.

Manuals

The following shows manuals relevant to this product.

Manual name

GOT2000 Series User's Manual (Hardware)

For detailed manuals and relevant manuals, refer to th e e-Manual or PDF manuals stored in the DVD-ROM for the screen design software used.

The latest manuals are also available from MI TSUBISHI ELECTRIC FA Global Website (www.MitsubishiElectric.com/fa).

Packing List

The following items are included.

Model Product Quantity

GT20-15PCO GT20-12PCO GT20-10PCO GT20-08PCO GT21-10WPCO GT21-07WPCO GT25-05PCO GT25-05PCO-2

Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law)

(Sold separately)

Protective cover f or oil

GOT2000 Series Protective Cover for Oil for GT27/GT25/GT23/ GT2107 User's Manual

Manual number

(Model code)

SH-081194ENG

(1D7MJ5)

(This manual)

1. OVERVIEW

This user’s manual explains GOT 2000 s eries protective cover for oil (hereinafter referred to as the protective cover for oil). Use of the protective cover for oil improves oil resistance and chemical resistance

of the GOT.

*1: It is not the one to guarantee all customer 's environments.

Moreover, it is not likely to be able to use it in the environment to which oil or the medicine splashes for a long time and the environment with which Oilmist is filled.

The following table shows the protective covers f or oil and the screen sizes for the applicable GOT

Model Screen sizes for the applicable GOTs

GT20-15PCO 15”

GT20-12PCO 12.1”

GT20-10PCO 10.4”

GT20-08PCO 8.4”

GT21-10WPCO 10.1” wide screen

GT21-07WPCO 7” wide screen

GT25-05PCO 5.7” (except GT2505)

GT25-05PCO-2 5.7” (GT2505)

GT25T-07WPCO 7” wide screen (rugged model)

2. SPECIFICATIONS

2.1 Performance specifications

The performance specifications of the protective cover for oil are indicate d below. The general specifications of the protective cover for oil a re the same as those of the GOT. For the general specifications of the GOT, refer to the GOT2000 Series User's Manual (Hardware).

Item GT20-15PCO GT20-12PCO GT20-10PCO GT20-08PCO

Level of

protection

For installing the GOT with the prot ective cover for oil, the control panel thickness must be

1.6 to 3mm because of the cover thickness. (Control panel thickness without the cover: 1.6 to 4mm)

Caution: Oil or the medicine might not be able to splash for a long time,

Material Cover: Nitrile rubber, Display: PET sheet

Weight 0.31(0.68) 0.21(0.46) 0.20(0.44) 0.16(0.35)

Item GT21-10WPCO GT21-07WPCO

Level of

Material Cover: Nitrile rubber, Display: PET sheet

Weight 0.14(0.30) 0.09(0.20)

Item GT25-05PCO GT25-05PCO-2 GT25T-07WPCO

Level of

Material Cover: Nitrile rubber, Display: PET sheet

Weight 0.09(0.20) 0.09(0.20) 0.15(0.33)

and to use it in the environment with which Oilmist is filled.

Caution: Oil or the medicine might not be able to splash for a long time,

and to use it in the environment with which Oilmist is filled.

Caution: Oil or the medicine might not be able to splash for a long time,

and to use it in the environment with which Oilmist is filled.

POINT

IP67F

Unit: kg(lb)

2.2 Oil resistance, chemical resistance

The protective cover for oil is made of material s with high oil and chemical resistance so that the cover can be used in various oil and chemical atmospheres. Because oils, including cutting oils, contain a small amount of additives depending on oil products, oil resistance of the cover cannot be st ated. Prior to use the cover, test the cover in operating environments, and then check the oil and chemical resistance of the cover.

Test contents and oil resistance of cover The protective cover for oil is soaked in the following oils for 2000 hours, and then oil resistance of the cover is checke d.

Oil type Product

Water-insoluble

cutting oil

(Yushiron oil CL35)

Water-soluble

cutting oil

(Noritake cool CG-

Grinding oil

50P)

Change in

appearance and

dimension

No change No change

Adhesion

between cover

and sheet

Oil resistance

3. EXTERNAL DIMENSIONS

Protective cover for oil

GOT

314

(12.36)

233

(9.96)

(0.47)

Unit: mm (inch)

252

(9.92)

209

(9.18)

(0.47)

Dimensions GT20-15PCO GT20-12PCO GT20-10PCO GT20-08PCO

Dimensions GT21-10WPCO GT21-07WPCO

W 263(10.35) 200(7.87)

H 205(8.07) 153(6.02)

D 12(0.47) 12(0.47)

Dimensions GT25-05PCO GT25-05PCO-2 GT25W-07WPCO

W 178(7.01) 175(6.89) 225(8.86)

H 154 (6.06) 153.5(6.04) 169(6.65)

D 12(0.47) 12(0.47) 12(0.47)

409

(16.10)

314.5

(12.38)

12.5

(0.49)

372

(14.65)

261

(10.28)

(0.47)

4. INSTALLATION AND REMOVAL PROCEDURE

POINT

For attaching the protective cover for oil to the GOT already mounted on the control panel, follow the procedures as below.

• Remove the GOT from the control panel. Make sure to externa lly shut off all phases of the p ower supply and remove all cables from the GOT in advance.

• Clean dirt off surfaces of the GOT and control panel.

4.1 install the protective cover

For attaching the protective cover for oil, refer to the example of the GT2712.

1) Position the POWER LED frame of the cover to the POWER LE D on the GOT front face, and the direction of the cover is deci ded

GOT

POWER LED

POWER LED Window

2) One corner of the cover is pulled outside, and it hangs it on the corner of the front panel of GOT.

Protective cover for oil

Please do not pull the oil cover more than the necessity, and do not bend it extremely. The seat part and the rubber part in the display part might flake off.

The corner is hung.

GOT

3) From the place where the cover is hung, hang the co rner of the cover sequentially and attach the entire edge of the cover to cover rubber packing parts in the back of the front panel of the GOT. (It is the order of the arrow from A side to D side.)

The corner on the left is hung and the oil cover is hung from A side to D side on the starting point sequentially.

POINT

Please confirm all surroundings.

Whether the rubber packing part is surely covered to prev ent going into such as the liquids in the board.

Make sure that corners of protective cover for oil match those of GOT front.

4) Mount the GOT onto the control panel.

When the control panel is dirty, clean the control panel. The panel cutting dimensions and mounting screw tightening torque with the protective cover for oil are the same as those without the cover. For mounting the GOT on the control panel, refer to the GOT2000 Series User's Manual (Hardware)

GOT

Protective cover for oil

Panel cut dimensions

Mounting metal fixture

Control panel

4.2 Removing the protective cover

Perform the reverse procedure to attaching the p rotective cover for oil.

5. PRECAUTIONS FOR USE

1) The protective cover for oil is a consumabl e product. Check the cover for scratch, damage or dirt at regular intervals, and replace with new one if necessary.

2) Do not push the protective cover for oil with point ed tools, including mechanical pencils and screwdrivers. Doing so causes scratches and damages of the cove r.

3) Do not clean the protective cover for oil with bleaches, thinners, organic solvents, corrosive chemicals, and other s. Doing so causes changes in shape and color of th e cover.

4) When the protective cover for oil is attached to the GOT, do not stretch and bend the cover too much. Doing so may cause a separation between the sheet and ru bber.

5) Do not place or use the protective cover for oil in direc t sunshine. When the protective cover for oil gets dusts, wipe the dusts off with a damp cloth.

6) When the protective cover00000 for oil is used , the USB connector on the GOT front face cannot be used.

7) When the protective cover for oil is used, the human sensor does not correctly operate. Disable the human sensor with the utility. For the human sensor setting, refer to the GOT2000 S eries User's Manual (Hardware).

8) Do not attach and remove the protective cover fo r oil frequently. Doing so reduces oil resistance and chemical resistance.

9) It is not the one to guarantee all customer 's environments. Moreover, it is not likely to be able to use it in the environment to which oil splashes for a long time and the environment wi th which Oilmist is filled.

Warranty

Mitsubishi Electric will not be held liable for damage caused by factors found not to be the cause of Mitsubishi Electric; machine damage or lost profits caused by faults in the Mitsubishi Electric products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi Electric; damages to products other than Mitsubishi Electric products; and to other duties.

For safe use

• This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufact ured to be incorporated in a device or system used in purposes related to human life.

• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric.

• This product has been manufactured under strict quality control. However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

Country/Region Sales office/Tel

USA

Brazil

Mexico

Germany

Italy

Spain

France

Czech

Turkey

Poland

Russia

South Africa

China

Taiwan

Korea

Singapore

Thailand

Indonesia

Vietnam

India

Australia

Mitsubishi Electric Automation, Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A. Tel: +1-847-478-2100 Mitsubishi Electric do Brasil Comercio e Servicos Ltda. Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP, Brasil CEP 06401-147 Tel: +55-11-4689-3000 Mitsubishi Electric Automation, Inc. Mexico Branch Mariano Escobedo #69, Col. Zona Industrial, Tlalnepantla Edo. Mexico, C.P.54030 Tel: +52-55-3067-7511 Mitsubishi Electric Europe B.V. German Branch Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany Tel: +49-2102-486-0 Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Hertfordshire, AL10 8XB, U.K. Tel: +44-1707-28-8780 Mitsubishi Electric Europe B.V. Italian Branch Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7, Agrate Brianza (MB), Italy Tel: +39-039-60531 Mitsubishi Electric Europe B.V. Spanish Branch Carretera de Rubi 76-80-Apdo.420, 08190 Sant Cugat del Valles (Barcelona), Spain Tel: +34-935-65-3131 Mitsubishi Electric Europe B.V. French Branch 25, Boulevard des Bouvets, 92741 Nanterre Cedex, France Tel: +33-1-55-68-55-68 Mitsubishi Electric Europe B.V. Czech Branch Avenir Business Park, Radlicka 751/113e, 158 00 Praha 5, Czech Republic Tel: +420-251-551-470 Mitsubishi Electric Turkey A.S. Umraniye Branch Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey Tel: +90-216-526-3990 Mitsubishi Electric Europe B.V. Polish Branch ul. Krakowska 50, 32-083 Balice, Poland Tel: +48-12-347-65-00 Mitsubishi Electric (Russia) LLC St. Petersburg Branch Piskarevsky pr. 2, bld 2, lit “Sch”, BC “Benua”, office 720; RU-195027 St. Petersburg, Russia Tel: +7-812-633-3497 Adroit Technologies 20 Waterford Office Park, 189 Witkoppen Road, Fourways, Johannesburg, South Africa Tel: +27-11-658-8100 Mitsubishi Electric Automation (China) Ltd. No.1386 Hongqiao Road, Mitsubishi Electric Automation Center, Shanghai, China Tel: +86-21-2322-3030 SETSUYO ENTERPRISE CO., LTD. 6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan Tel: +886-2-2299-2499 Mitsubishi Electric Automation Korea Co., Ltd. 7F-9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu, Seoul 07528, Korea Tel: +82-2-3660-9530 Mitsubishi Electric Asia Pte. Ltd. 307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943 Tel: +65-6473-2308 Mitsubishi Electric Factory Automation (Thailand) Co., Ltd. 12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road, Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand Tel: +66-2682-6522 to 31 PT. Mitsubishi Electric Indonesia Gedung Jaya 11th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia Tel: +62-21-3192-6461 Mitsubishi Electric Vietnam Co., LTD. Ho Chi Minh Head Office Unit 01-04, 10th Floor, Vincom Center, 72 Le Thanh Ton Street, District 1, Ho Chi Minh City, Vietnam Tel: +84-8-3910-5945 Mitsubishi Electric India Pvt. Ltd. Pune Branch Emerald House, EL -3, J Block, M.I.D.C., Bhosari, Pune - 411026, Maharashtra, India Tel: +91-20-2710-2000 Mitsubishi Electric Australia Pty. Ltd. 348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W. 2116, Australia Tel: +61-2-9684-7777

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice. Printed in Japan, March 2019.