Mitsubishi GT1662-VNBA, GT1675-VNBA, GT1675M-STBD, GT1695M-XTBD, GT1675-VNBD General Description Manual

GT16 General Description

WARNING

CAUTION

WAR NI NG

WAR NI NG

CAUTION

WAR NI NG

CAUTION

CAUTION

WARNING

CAUTION

WARNING

WARNING

CAUTION

CAUTION

WAR NI NG

CAUTION

CAUTION

CAUTION

Unit:mm (inch)

397(15.6)
320(12.6)

296(11.7)

320(12.6)

6(0.24)

61(2.40)

10 382(15.0) 10

281(11.1)

(0.39) (0.39)

GT1695

10(0.39)

10(0.39)

GT1695M-XTBA
GT1675M-STBA
GT1675-VNBA
GT1665M-STBA
GT1662-VNBA

Thank you for purchasing the GOT1000 Series.

Prior to use, please read both this manual and the
detailed manual thoroughly to fully understand the
product.

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant
manuals introduced in this manual carefully and pay full attention to
safety to handle the product correctly.
The precautions given in this manual are concerned with this prod­uct.
In this manual, the safety precautions are ranked as "WARNING"
and "CAUTION".

Note that the CAUTION level may lead to a serious accident
according to the circumstances.
Always follow the instructions of both levels because they are impor­tant to personal safety.
Please save this manual to make it accessible when required and
always forward it to the end user.

[DESIGN PRECAUTIONS]

 Some failures of the GOT, communication unit or cable may keep the outputs

on or off.
Some failures of a touch panel may cause malf unction of the input objects
such as a touch switch.
An external monitoring circuit should be provided to check for output signals
which may lead to a serious accident.
Not doing so can cause an accident due to false outp ut or malfunction.

 If a communication fault (including cable disconnection) occ urs during

monitoring on the GOT, communication between the GOT and PLC CPU is
suspended and the GOT becomes inoperative.
For bus connection : The CPU becomes faulty and the GOT becomes
inoperative.
For other than bus connection : The GOT becom es inoperative.
A system where the GOT is used should be confi gured to perform any
significant operation to the system by using the switc hes of a device other
than the GOT on the assumption that a GOT communi cation fault will occur.
Not doing so can cause an accident due to false outp ut or malfunction.

 Do not use the GOT as the warning device that may cause a ser ious

accident.
An independent and redundant hardware or mechanic al interlock is required
to configure the device that displays and outputs se rious warning.
Failure to observe this instruction may result in an accident due to incorrect
output or malfunction.

GT1695M-XTBD
GT1675M-STBD
GT1675-VNBD
GT1665M-STBD
GT1662-VNBD

GT1685M-STBA
GT1675M-VTBA
GT1672-VNBA
GT1665M-VTBA
GT1655-VTBD

GT1685M-STBD
GT1675M-VTBD
GT1672-VNBD
GT1665M-VTBD

MODEL GT16-U-GD-E

Model

code

1D7MP6

IB(NA)-0800544ENG-A(1410)MEE

SAFETY PRECAUTIONS

Indicates that incorrect handling may cause
hazardous conditions, resulting in death or
severe injury.

Indicates that incorrect handling may cause
hazardous conditions, resulting in medium or
slight personal injury or physical damage.

[DESIGN PRECAUTIONS]

1

2

 Incorrect operation of the touch switch(s) may lead to a serious accident if the

3

4

5

6

7

8

9

0

1

2

3

4

5

6

7

8

9

0

GOT backlight is gone out.
When the GOT backlight goes out, although the POWER LE D blinks (green/
orange) and the display section dims, the input of the touch switc h(s) remains
active.
This may confuse an operator in thinking that the GOT is in "screensaver"
mode, who then tries to release the GOT from this mode by touching the
display section, which may cause a tou ch switch to operate.
Note that the following occurs on the GOT when the b acklight goes out.

• GT1655-V: The POWER LED blinks (green/orange) and the monitor screen
appears blank.

• Models other than GT1655-V: The POWER LED blinks ( green/orange) and
the monitor screen appears dimmed.

 The display section of the GT16 is an analog-resistive t ype touch panel.

If you touch the display section simultaneously in 2 points or mor e, the switch
that is located around the center of the touched poin t, if any, may operate.
Do not touch the display section in 2 points or more simultaneously.
Doing so may cause an accident due to incorrect o utput or malfunction.

 When programs or parameters of the controller (such as a PLC) that is

monitored by the GOT are changed, be sure to reset the GOT or shut off the
power of the GOT at the same time.
Not doing so can cause an accident due to false outp ut or malfunction.

[DESIGN PRECAUTIONS]

 Do not bundle the control and communication cables with main-circui t, power

or other wiring.
Run the above cables separately from such wiring and kee p them a minimum
of 100mm apart.
Not doing so noise can cause a malfunction.

 Do not press the GOT display section with a pointed material a s a pen or

driver.
Doing so can result in a damage or failure of the dis play section.

 When the GOT is connected to the Ethernet network, the available IP

address is restricted according to the system configuration.

• When multiple GOTs are connected to the Ethernet network:
Do not set the IP address (192.168.0.18) for the GOTs and the controllers in
the network.

• When a single GOT is connected to the Ethernet n etwork:
Do not set the IP address (192.168.0.18) for th e controllers except the GOT
in the network.
Doing so can cause the IP address duplication. The duplication can
negatively affect the communication of the device with th e IP address
(192.168.0.18).
The operation at the IP address duplication depe nds on the devices and the
system.

 Turn on the controllers and the network devices to be ready for

communication before they communicate with the GOT.
Failure to do so can cause a communication err or on the GOT.

[MOUNTING PRECAUTIONS]

 Be sure to shut off all phases of the external power supply used by the

system before mounting or removing the GOT main un it to/from the panel.
Not doing so can cause the unit to fail or malfunction.

 Be sure to shut off all phases of the external power supply used by the

system before mounting or removing the communicati on unit, option function
board onto/from the GOT.
Not doing so can cause the unit to fail or malfunction.

 When installing the option function board, wear an earth band etc. to avoid

the static electricity.
Not doing so can cause a unit corruption.

 Use the GOT in the environment that satisfies the general speci fications

described in this manual.
Not doing so can cause an electric shock, fire, mal function or product
damage or deterioration.

 When mounting the GOT to the control panel, tighten the mounting screws in

the specified torque range (0.36 to 0.48 N•m) with a Phillips-head screwdriver
No.2.
Undertightening can cause the GOT to drop, short circuit or malfunction.
Overtightening can cause a drop, short circuit or malf unction due to the
damage of the screws or the GOT.

 When loading the communication unit to the GOT, fit it to the connection

interface of the GOT and tighten the mounting screws in the specified torque
range (0.36 to 0.48 N•m) with a Phillips-head screwdriver No.2.
Under tightening can cause the GOT to drop, short circuit or malfunction.
Overtightening can cause a drop, failure or malfu nction due to the damage of
the screws or unit.

 When mounting the option function board onto the GOT, connect it to the

corresponding connector securely and tighten the mounting screws within the
specified torque range (0.25 to 0.35 N•m) with a Phillips-head screwdriver
No.1.
Undertightening can cause malfunction due to po or contact.
Overtightening can cause malfunction due to scr ew or unit damage.

 When inserting a CF card into the GOT, push it into the insertion slot until the

CF card eject button will pop out.
If not properly inserted, a bad connection may caus e a malfunction.

 When inserting/removing a CF card into/from the GOT, turn the CF card

access switch off in advance.
Failure to do so may corrupt data within the CF card.

 When removing a CF card from the GOT, make sure to support the CF card

by hand, as it may pop out.
Failure to do so may cause the CF card to drop from the GOT and break.

[MOUNTING PRECAUTIONS]

 When installing a USB memory to the GOT, make sure to install the USB

memory to the USB interface firmly.
Failure to do so may cause a malfunction due to poor contact.

 Before removing the USB memory from the GOT, operate the utility screen

for removal. After the successful completion dialog box is displayed, remove
the memory by hand carefully.
Failure to do so may cause the USB memory to drop , resulting in a damage
or failure of the memory.

 For closing the USB environmental protection cover, fix the cover by pushing

the mark on the latch firmly to comply with the protective structure.

 Remove the protective film of the GOT.

When the user continues using the GOT with the protective film, the film may
not be removed.

 Operate and store the GOT in environments without direct sunlig ht, high

temperature, dust, humidity, and vibrations.

 When using the GOT in the environment of oil or chemicals, u se the

protective cover for oil.
Failure to do so may cause failure or malfuncti on due to the oil or chemical
entering into the GOT.

[WIRING PRECAUTIONS]

 Be sure to shut off all phases of the external power supply used by the

system before wiring.
Failure to do so may result in an electric shoc k, product damage or
malfunctions.

 Always ground the FG terminal, LG terminal, and Functional ground terminal

of the GOT power to the protective ground conductors dedicated to the GOT.
Not doing so may cause an electric shock or malfunc tion.

 When tightening the terminal screws, use a Phillips-head screwd river No.2.
 Terminal screws which are not to be used must be tightened always at torque

0.5 to 0.8 N•m.
Otherwise there will be a danger of short circuit agai nst the solderless
terminals.

 Use applicable solderless terminals and tighten them with the specified

torque.
If any solderless spade terminal is used, it may be disconnected when the
terminal screw comes loose, resulting in fail ure.

 Correctly wire the GOT power supply section after confirming the rated

voltage and terminal arrangement of the product.
Not doing so can cause a fire or failure.

 Tighten the terminal screws of the GOT power supply section i n the specified

torque range (0.5 to 0.8 N•m). Undertightening can caus e a short circuit or
malfunction.
Overtightening can cause a short circuit or mal function due to the damage of
the screws or the GOT.

 Exercise care to avoid foreign matter such as chips and wire offcuts entering

the GOT. Not doing so can cause a fire, failure or malfunction.

 The module has an ingress prevention label on its top to preven t foreign

matter, such as wire offcuts, from entering the module during wiring.
Do not peel this label during wiring.
Before starting system operation, be sure to peel this label because of heat
dissipation.

 Plug the communication cable into the connector of the connected unit and

tighten the mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or ma lfunction.
Overtightening can cause a short circuit or mal function due to the damage of
the screws or unit.

 Plug the QnA/ACPU/Motion controller(A series) bus connec tion cable by

inserting it into the connector of the connected u nit until it "clicks".
After plugging, check that it has been inserted snug ly.
Not doing so can cause a malfunction due to a contact faul t.

[TEST OPERATION PRECAUTIONS]

 Before performing the test operations of the user creation monito r screen

(such as turning ON or OFF bit device, changing the word device current
value, changing the settings or current values of the timer or counter, and
changing the buffer memory current value), read through th e manual
carefully and make yourself familiar with the oper ation method.
During test operation, never change the data of the devices which are used to
perform significant operation for the system.
False output or malfunction can cause an accident.

[STARTUP/MAINTENANCE PRECAUTIONS]

 When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfuncti on.

 Correctly connect the battery connector.

Do not perform the following actions to the battery.

• Charging, disassembling, heating, short-circuiting, or s oldering the battery,
or throwing it into the fire
Doing so will cause the battery to produce heat, explode, or ignite, resulting in
injury and fire.

 Before starting cleaning or terminal screw retightening, always switch off the

power externally in all phases.
Not switching the power off in all phases can cause a uni t failure or
malfunction.
Undertightening can cause a short circuit or ma lfunction.
Overtightening can cause a short circuit or mal function due to the damage of
the screws or unit.

[STARTUP/MAINTENANCE PRECAUTIONS]

 Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

 Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

 The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling,
motion or accidental pulling of the cables or can cause a malfunct ion due to a
cable connection fault.

 When unplugging the cable connected to the unit, do not hold and pul l the

cable portion.
Doing so can cause the unit or cable to be damaged o r can cause a
malfunction due to a cable connection fault.

 Do not drop the module or subject it to strong shock. A module damage ma y

result.

 Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the
battery.
If the battery is dropped or given an impact, dispose of it without using.

 Before touching the unit, always touch grounded metals, etc. to dis charge

static electricity from human body, etc.
Not doing so can cause the unit to fail or malfunction.

 Replace battery with GT15-BAT or GT11-50BAT by Mitsubishi electric

Co.only.
Use of another battery may present a risk of fire or exp losion.

 Dispose of used battery promptly.

Keep away from children.Do not disassemble and do not dispose of in fire.

[TOUCH PANEL PRECAUTIONS]

 For the analog-resistive film type touch panels, normally the adjustment is not

required.
However, the difference between a touched position and the object position
may occur as the period of use elapses. When any difference b etween a
touched position and the object positio n occurs,execute the touch panel
calibration.

 When any difference between a touched position and the object pos ition

occurs, other object may be activated. This may c ause an unexpected
operation due to incorrect output or malfunction.

[BACKLIGHT CHANGING PRECAUTIONS]

 Before changing the backlight, always switch off the GOT power externally in

all phases (when the GOT is connected to the bus, the PLC CPU power must
also be switched off externally in all phases) an d remove the GOT from the
control panel.
Not switching the power off in all phases may cau se an electric shock.
Not removing the unit from the control panel can cause in jury due to a drop.

 When replacing the backlight, use the gloves.

Otherwise, it may cause you to be injur ed.

 Start changing the backlight more than 5 minutes after switching the GOT

power off.
Not doing so can cause a burn due to the heat of the back light.

[DISPOSAL PRECAUTIONS]

 When disposing of this product, treat it as industrial waste .

When disposing of batteries, separate them from other wastes according to
the local regulations.
(Refer to the User's Manual for the GOT you are usin g for details of the
battery directive in the EU member states.)

[TRANSPORTATION PRECAUTIONS]

 When transporting lithium batteries, make sure to treat them based on the

transport regulations.
(Refer to the User's Manual for the GOT you are usin g for details of the
regurated models.)

 Make sure to transport the GOT main unit and/or relevant unit(s ) in the

manner they will not be exposed to the impact exceedin g the impact
resistance described in the general specifications of t he User's Manual, as
they are precision devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.

 When fumigants that contain halogen materials such as fluorine, chlori ne,

bromine, and iodine are used for disinfecting and p rotecting wooden
packaging from insects, they cause malfunction when ent ering our products.
Please take necessary precautions to ensure that rem aining materials from
fumigant do not enter our products, or treat packaging with methods oth er
than fumigation (heat method).
Additionally, disinfect and protect wood from insects before packing products.

The following shows manuals relevant to this product.

Manual

Detailed Manual

Manual name

GT16 User's Manual (Hardware)
(Sold separately)

GT16 User's Manual (Basic Utility)
(Sold separately)

For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the
drawing software used.

Manual number

(Model code)

SH-080928ENG

(1D7MD3)

SH-080929ENG

(1D7MD4)

Relevant Manuals

For relevant manuals, refer to the Help or the PDF m anuals stored in the DVD­ROM for the drawing software used.

The latest manuals are also available from MITS UBISHI ELECTRIC FA Global
Website (http://www.MitsubishiElectric.co.jp/fa/).

Before using the GOT

Connect the connector of the GOT to the connector of t he battery.
For details on GT16 specifications, installing proce dure, EMC Directive, wiring,
maintenance and inspection, or checking method f or the version and the
compatible standard, refer to GT16 User's Manual (Hardware).

Packing List

The GOT product package includes the following:

© 2014MITSUBISHI ELECTRIC CORPORATION

Model name Product Quantity

GT1695M-X

GT1685M-S
GT1675M-S
GT1675M-V
GT1675-VN
GT1672-VN
GT1665M-S
GT1665M-V

GT1655-V

GOT 1

Battery (GT15-BAT) 1

Installation fitting 8

GT16 General Discription 1

GT16本体概要説明書

GOT 1

Battery (GT15-BAT) 1

Installation fitting 4

GT16 General Discription 1

GT16本体概要説明書

GOT 1

Battery (GT11-50BAT) 1

Installation fitting 4

GT16 General Discription 1

GT16本体概要説明書

1. FEATURES

(1) Improved monitoring performance and connectivity to FA devices

• GT1695M-X, GT1685 M-S, GT1675M-S, GT1675M-V, GT1665M-S,
GT1665M-V, GT1655-V: The TFT color liquid crystal display (high intensity,
wide angle view, and high definition type) provides clear full-color display
and displays small characters clearly.
(Displays digital images of BMP and other for mats in 65536 colors.)
GT1675-VN, GT1672-VN, GT1662-VN: The TFT color liquid crystal display
provides 4096 or 16 colors to offer a wide range of models that meet user
requirements.

• Provides multi-l anguage display function based on Unicode2.1 True Type
font and high-speed drawing of beautiful text.

• High speed monitori ng through high speed communication at maximum of

115.2kbps.

• High speed displ ay and high speed touch switch response.

• The operation per formance is improved by the analog touch panel.

• GT1695M-X, GT1685 M-S, GT1675M-S, GT1675M-V, GT1665M-S,
GT1665M-V: Applicable to a video/RGB unit and a multimedia u nit

(2) More efficient GOT operations including screen design, s tartup, adjustment,

management and maintenance works

• GT1695M-X, GT1685 M-S, GT1675M-S, GT1675M-V, GT1665M-S,
GT1665M-V, GT1655-V: 15MB user memory is included as standard.
GT1675-VN, GT1672-VN, GT1662-VN: 11MB user memory is included as
standard.

• Interfaces are included as standard. (Ethernet, RS-232, RS-422/485, CF
card, and USB)

• Font installation is available to increase the system fonts.

• Combined use of 4 ty pes of alarms (system alarm, user alarm, alarm
history, alarm popup display) realizes more efficient alarm notification.

• Maintenance timing r eport function is available that measures the ba cklight
energization time and notifies of maintenance time .

• The USB interface is positioned on the GOT front. This enables the system
startup to be performed more efficiently using FA device startup tool, and
eliminates the necessity of indirect wor ks (opening and closing the control
panel, cable replacement, cable rewiring) in order to imp rove the working
efficiency.

• The blown backl ight bulb can be confirmed even during screen saving, with
the blinked POWER LED at backlight shutoff detection.

(3) Enhanced support of FA device setup tools

• Transferring and monitoring sequence programs with the personal computer
connected to the GOT can be executed when connectin g to a PLC CPU
with the direct CPU connection or bus connection. (FA transparent function)

2. Part Names and Settings

Part Names and Settings of the GT16

Example)

21)

GT1695

2),3)

1)

4)

5)

19)

19)

6) 7) 8)

No. Name Description

1) POWER LED

2) Display screen Displays the Utility and the user creation sc reen.

3) Touch key

1

1

1

4) USB interface (Device)

5) USB interface (Host)

6) RS-232 interface

7) Ethernet interface

8) RS-422/485 interface

9) Power terminal

10) Extension interfac e1 For installing an exten sion unit (I/F-1)

11) Extension interface2

12) CF card interface For installing a CF card

13) CF card access LED Lit : CF card accessed , Not lit : CF card not accessed

14) CF card access switch

15) Video/RGB interface

Terminating resistor

16)
setting switch

Optional function

17)
board interface

18) Reset switch

Hole for unit

19)
installation fitting

20) Battely cover

21) Human sensor

22) Installation switch Used for OS installations at the GOT startup

*1: No video/RGB interface on the GT1675-VN, G T1672-VN, GT1662-VN, and

GT1655-V.
*2: Battery holder for the GT1665 and GT16 62.
*3: No extension interface 2 on the GT16 55.
*4: Located on the extension interface 2 o n the GT1655.
*5:Integral with the CF card interface cover for t he GT1655.
*6:No human sensor on the GT1675, GT1672, GT1665, GT 1662, and GT1655.
*7:No LG terminal on the GT1655.
*8:On the rear face of the GT1655, the functional grou nd terminal is located on the

left side of the FG terminal.

Lit in green : Power is correctly supplied , Lit in orange :
Screen saving
Blinks in orange/green : Blown back light bulb , Not lit :
Power is not supplied

For operating touch switches in the Utility and the user
creation screen

For connecting a persona l computer (Connector type: Mini­B)

For USB mouse/keyboard ,dat a transfer and storage
(Connector type: TYPE-A)

For communicating with a co ntroller or connecting a
personal computer(Connec tor type: D sub 9-pin)

For communicating with a controller or using the gateway
function (Connector ty pe: RJ-45 (modular jack))

For communicating with a controller (Connector type: 14-pin
(female))

*8

Power input terminal, LG terminal*7, FG terminal

*3

For installing an exten sion unit (I/F-2)

Used for accepting or stopping the access to the CF card
before removing the CF card from the GOT
ON :CF card being accessed (CF card removal

OFF :CF card not accessed (CF card removal possible)

For mounting the video input unit, RGB input unit, video/

*1

RGB input unit, RGB output unit, or multimedia unit

For switching on and off of the terminating resistor for the
RS-422/485 communication port

For installing the opti onal function board

*4

Hardware reset switch (Inoperative in the bus connection or
with the bus connection unit installed)

Hole for inserting the unit installation fitting

*2*5

Houses the battery

*6

Sensor that detects human movement

9)

prohibited)

GOT
Rear face

19)

17) 16)

10) 11)

22)

12)

13)

14)

20)

15)

18)

3. Specifications

3.1 General Specifications

Item Specifications

Display
section

Operating

Zone

ambient

d'affichage

temperature

*1

Other than
the display

Température
ambiante de

section

fonctionnem

Autre que la

*1

ent

zone
d'affichage

Storage ambient
temperature

Operating ambient
humidity

Storage ambient humidity 10 to 90% RH, non-condensing

Compliant
with JIS B

intermittent

Vibration resistance

Shock resistance

Operating atmosphere

Operating altitude
Installation location Inside control panel
Overvoltage category
Pollution degree
Cooling method Self-cooling
Grounding Grounding with a resistan ce of 100Ω or less

*1: When mounting a multimedia unit (GT 16M-MMR), MELSECNET/H

communication unit (GT15-J71LP23-25, GT15-J7 1BR13), or CC-Link
communication unit (GT15-J61BT13), the operating ambient temp erature must
be reduced 5 °C against the maximum values describe d in general
specifications.

Lors du montage d'un module multimédia (GT16M-MMR), du module de

communication MELSECNET/H (GT15-J71LP23-25, GT15-J71BR13) ou du
module de communication CC-Link (GT15-J61BT13), la température ambiante
de fonctionnement doit être réduite de 5°C par rapport aux valeurs maximales
décrites dans les spécifications générales.

*2: Do not use or store the GOT under pr essure higher than the atmospheric

pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a
malfunction.
When an air purge is made inside the control panel by adding pressure, there
may be a clearance between the surface sheet and the screen making it difficult
to use the touch panel, or the sheet may come off.

*3: This indicates the section of the power supply to which the equipment is

assumed to be connected between the public electric al power distribution
network and the machinery within the premises.
Category II applies to equipment for which electrical powe r is supplied from
fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.

*4: This index indicates the degree to which conductive material is generated in the

environment where the equipment is used.
In pollution degree 2, only non-conductive pollu tion occurs but temporary
conductivity may be produced due to condensa tion.

Point

Refer to GT16 User's Manual for details of the performance specifications of each GOT.

3502 and

vibration

IEC 61131-

2

continuous

vibration

Compliant with JIS B 3502 and IEC 61131-2 147 m/s2(15G),

No greasy fumes, corrosive gas, flammable gas, excessive

conductive dust, and direct sunlight (Same as storage

*2

*3

*4

3.2 Power Supply Specifications

The following indicates the power supply s pecifications for GT16.

Note

Operation at momentary failure

• If an instantaneous power failure occurs in the power supply and continues for more
than the permissible period, the GOT will be reset.

• Make sure to power on the unit more than 5 seconds after power-off.

3.2.1 For GOTs powered from the 100 to 240VAC
power supply

Item

Input power supply volta ge 100 to 240VAC (+10%, -15%)
Input frequency 50/60Hz 5%

Input max. apparent power

Power consumption 64W or less 46W or less 39W or less

At backlight off 38W or less 32W or less 30W or less

Inrush current 28A or less (4ms) (maximum load)

GT1695M-XTBA GT1685M-STBA

(maximum load)

0 to 50

0 à 50

0 to 55

0 à 55

-20 to 60

10 to 90% RH, non-condensing

Frequency Accelera tion

5 to 8.4Hz - 3.5mm

Under

8.4

to150Hz

Under

3 times each in X, Y and Z direct ions

150VA

9.8m/s2-

5 to 8.4Hz - 1.75mm

to 150Hz

4.9m/s2-

8.4

atmosphere)

2000 m (6562 ft) max.

II or less
2 or less

Specifications

110VA

(maximum load)

Half-

Sweep

amplitude

count

10 times

each in X,

Y and Z

directions

GT1675M-STBA
GT1675M-VTBA

GT1675-VNBA

GT1672-VNBA
GT1665M-STBA
GT1665M-VTBA

GT1662-VNBA

100VA

(maximum load)

-

Item

Allowable momentary power
failure time

Noise immunity

Dielectric withstand voltage 1500VAC for 1 minute across power terminals and earth

Insulation resistance

Applicable wire size 0.75 to 2[mm

Applicable solderless terminal

Applicable tightening torque
(Terminal block terminal screw)

GT1695M-XTBA GT1685M-STBA

1,500Vp-p noise voltag e, 1 s noise width (when
measuring with a noise si mulator under 25 to 60Hz
noise frequency)

10MΩ or more across power termin als and earth by a
500V DC insulation resistance te ster

Solderless terminal for M3 screw RAV1.25-3, V2-S3.3,

3.2.2 For GOTs powered from the 24VDC power
supply

Item

Input power supply
voltage

Power
consumption

At backlight off 30W or less 26W or less 27W or less 14W or less

Inrush current

Allowable
momentary power
failure time

Noise immunity

Dielectric withstand
voltage
Insulation
resistance

Applicable wire size 0.75 to 2[mm

Applicable
solderless terminal

Applicable
tightening torque
(Terminal block
terminal screw)

GT1695M-

XTBD

60W or less 40W or less 38W or less 16W or less

12A or less

(75ms)

(maximum

load)

500Vp-p noise voltage, 1 s nois e width (when measuring with a
noise simulator under 25 to 60Hz noise frequency)

500VDC for 1 minute across power terminals and earth

10MΩ or more across power terminals and earth by a 500V DC
insulation resistance test er

Solderess terminal for M3 screw RAV1.25-3, V2-S3.3, V2-N3A, FV2-

3.3 External Dimensions

GT1675,GT1672

10(0.39)

199 (7.83)

6(0.24)

10(0.39)

GT1655

10(0.39)10(0.39)

120(4.72)

56 (2.20)

6

(0.24)

214 (8.43)

135(5.31)

60(2.36)

303 (11.93)

252 (9.92)

222 (8.74)

288 (11.34)

167(6.57)
116(4.57)

116(4.57)

152(5.98)

49

Unit: mm (inch)

Unit: mm (inch)

Specifications

20 ms or less (100VAC or more)

V2-N3A, FV2-N3A

0.5 to 0.8[N•m]

Specifications

GT1675M-STBD
GT1675M-VTBD

GT1685M-

12A or less (55ms) (maximum

GT1685

10(0.39)

227(8.94)

10(0.39)

GT1665,GT1662

(1.93)

GT1675-VNBD
GT1672-VNBD

STBD

GT1665M-STBD
GT1665M-VTBD

GT1662-VNBD

DC24V (+25%, -20%)

load)

10 ms or less

N3A

0.5 to 0.8[N•m]

242(9.53)

6(0.24)

56(2.20)

10(0.39)175 (6.89)

190 (7.48)

6(0.24)

10(0.39)

56 (2.20)

316(12.44)
240(10.35)

240(9.84)

301(11.85)

175.5 (6.91)

175.5 (6.91)

2

]

Unit: mm (inch)

241 (9.49)

226 (8.90)

GT1675M-STBA
GT1675M-VTBA

GT1675-VNBA

GT1672-VNBA
GT1665M-STBA
GT1665M-VTBA

GT1662-VNBA

2

]

GT1655-VTBD

67A or less
(1ms)
(maximum
load)

52(2.05)

Unit: mm (inch)

52

(2.05)

4. EMC AND LOW VOLTAGE DIRECTIVE

For the products sold in European countries, the conformance to the
EMC Directive, which is one of the European Directives, has been a
legal obligation since 1996. Also, conformance to the Low Voltage.
Directive, another European Directives, has been a legal obligation since

1997.
Manufacturers who recognize their products must conform to the EMC
and Low Voltage Directive are required to declare that their products
conform to these Directives and put a "CE mark" on their products.

• Authorized representative in Europe
Authorized representative in Europe is shown below.
Name :Mitsubishi Elec tric Europe BV
Address :Gothaer strase 8, 40880 Ratingen, Germany

4.1 Requirements to Meet EMC Directive

EMC Directives are those which require "any strong electromagnetic
force is not output to the external.:Emission (electromagnetic
interference)" and "It is not influenced by the electromagnetic wave from
the external.: Immunity (electromagnetic sensitivity)".
Items4.1.1 through4.1.3 summarize the precautions to use GOT and
configure the mechanical unit in order to match the EMC directives.
Though the data described herein are produced with our best on the

basis of the requirement items and standards of the restrictions gathered
by Mitsubishi, they do not completely guaranteed that all mechanical unit
manufactured according to the data do not always match the above
directives. The manufacturer itself which manufactures the mechanical
unit must finally judge the method and others to match the EMC
directives.

4.1.1 EMC directive

The standards of the EMC Directive are shown below.

Applied

standard

EN61131-2
: 2007

*1: The GOT is an open type device (device ins talled to another device) and must

Test standard Test details Standard value

Electromagnetic

*1

*1

emissions from the

*1

product are
measured.

Electromagnetic
emissions from the

*1

product to the power
line is measured.

Immunity test in
which static
electricity is applied
to the cabinet of the
equipment.

Immunity test in
which field is
irradiated to the
product.

Immunity test in
which burst noise is
applied to the power
line and signal lines.

Immunity test in
which lightening

*1

surge is applied to
the product.

Immunity test in
which a noise
inducted on the
power and signal
lines is applied.
Test for checking
normal operations
under the
circumstance
exposed to the
ferromagnetic field
noise of the power
supply frequency
(50/60Hz).

Test for checking
normal operations
at instantaneous
power failure.

CISPR16-2-3
Radiated noise

CISPR16-2-1
Conducted noise

IEC61000-4-2
Electrostatic
immunity

IEC61000-4-3
Radiated
electromagnetic
field AM modulation

IEC61000-4-4
Fast transient burst

*1

noise

IEC61000-4-5
Surge immunity

IEC61000-4-6
Conducted RF
immunity

IEC61000-4-8
Power supply
frequency magnetic
field immunity

EN61000-4-11
EN61000-4-29
Instantaneous
power failure and
voltage dips
immunity

be installed in a conductive control panel.
The above test items are conducted in the condition where the GOT is installed
on the conductive control panel and combined with the Mitsubishi PLC.

30M-230MHz QP:
30dB V/m (30m in
measurement range)
230M-1000MHz QP:
37dB V/m(30m in
measurement range)

150k-500kHz QP:79dB,
Mean: 66dB
500k-30MHz QP:73dB,
Mean: 60dB

4kV Contact discharge
8kV Aerial discharge

80-1000MHz:10V/m

1.4-2GHz:3V/m

2.0-2.7GHz:1V/m
80%AM modulation@1kHz
Power line:2kV
Digital I/O(24V or high er): 1kV
(Digital I/O(24V or less))> 250V
(Analog I/O, signal lines)> 250V
AC power type

Power line (between line and
ground): 2kV
Power line (between lines)
: 1kV
Data communication port
: 1kV

DC power type

Power line (between line and
ground) : 0.5kV

Power line (between lines)

: 0.5kV

Data communication port

: 1kV

Power line: 10V
Data communication port: 1 0V

30 A/m

AC power type

0.5 cycle 0% (interval 1 to 10s)
250/300 cycle 0%
10/12 cycle 40%
25/30 cycle 70%

*2, *3

*2, *3

*2

*2

*2: QP (Quasi-Peak): Quasi-peak value, Mean: Average value
*3: The above test items are conducted in the foll owing conditions.

30M-230MHz QP : 40dB V/m (10m in measurement range)
230M-1000MHz QP : 47dB V/m (10m in measurement range)

4.1.2 Control panel

The GOT is an open type device (device installed to another device) and
must be installed in a conductive control panel.
It not only assure the safety but also has a large effect to shut down the
noise generated from GOT, on the control panel.
(1) Control Panel

(a) The control panel must be conductive.
(b) When fixing a top or bottom plate of the control panel wit h bolts,

do not coat the plate and bolt surfaces so that they will come into
contact.
And connect the door and box using a thick grounding cable in
order to ensure the low impedance under high frequency.

(c) When using an inner plate to ensure electric conductivity with the

control panel, do not coat the fixing bolt area of the inner plate
and control panel to ensure conductivity in the largest area as
possible.

(d) Ground the control panel using a thick grounding cable in order to

ensure the low impedance under high frequency.

(e)The diameter of cable holes in the control panel must be 10cm

(3.94in.). In order to reduce the chance of radio waves leaking out,
ensure that the space between the control panel and its door is
small as possible.
Paste the EMI gasket directly on the painted surface to seal the
space so that the leak of electric wave can be suppressed.

Manufacturer Series model name

KITAGAWA INDUSTRIES CO., LTD. UC series (Recommended Product)

Our test has been carried out on a panel having the damping
characteristics of 37dB max. and 30dB mean (measured by 3m
method with 30 to 300MHz).

(2) Connection of power and ground wires

Ground and power supply wires for the GOT must be connected as
described below.
(a) Provide a grounding point near the GOT. Short-circuit the LG and

FG terminals of the GOT (LG: line ground, FG: frame ground)
and ground them with the thickest and shortest wire possible
(The wire length must be 30cm (11.81in.) or shorter.)
The LG and FG terminals function is to pass the noise generated
in the PC system to the ground, so an impedance that is as low
as possible must be ensured. As the wires are used to relieve the
noise, the wire itself carries a large noise content and thus short
wiring means that the wire is prevented from acting as an
antenna.
Note) A long conductor will become a more efficient antenna at
high frequency.

(b) The earth wire led from the earthing point must be twisted with

the power supply wires.
By twisting with the earthing wire, noise flowing from the power
supply wires can be relieved to the earthing. However, if a filter is
installed on the power supply wires, the wires and the earthing
wire may not need to be twisted.

4.1.3 Noise filter (power supply line filter)

The noise filter (power supply line filter) is a device effective to reduce
conducted noise. Except some models, installation of a noise filter onto
the power supply lines is not necessary. However conducted noise can
be reduced if it is installed. (The noise filter is generally effective for
reducing conducted noise in the band of 10MHz or less.) Usage of the
following filters is recommended.

Model name FN343-3/01 FN660-6/06 ZHC2203-11

Manufacturer SCHAFFNER SCHAFFNER TDK

Rated current 3A 6A 3A

Rated voltage 250V

The precautions required when installing a noise filter are described
below.

(1) Do not install the input and output cables of the noise filter together

to prevent the output side noise will be inducted into the input side
cable where noise has been eliminated by the noise filer.

Input side

(power supply side)

Filter

• I nstalling the input and output cables
together will cause noise induction.

Induction

Output side

(device side)

Input side

(power supply side)

Filter

Output side

(device side)

• Separate the input cable from the output
cable.

(2) Connect the noise filter's ground terminal to the control panel with

the shortest cable as possible (approx. 10cm (3.94 in.) or less).

4.2 Requirements for Compliance with the Low
Voltage Directive

The Low Voltage Directive requires each device which operates with
power supply ranging from 50VAC to 1000V and 75VDC to 1500V to
satisfy necessary safety items.
In the Sections from 4.2.1 to 4.2.5, cautions on installation and wiring of
the GOT to conform to the Low Voltage Directive requires are described.
We have put the maximum effort to develop this material based on the
requirements and standards of the Directive that we have collected.
However, compatibility of the devices which are fabricated according to
the contents of this manual to the above Directive is not guaranteed.
Each manufacturer who fabricates such device should make the final
judgement about the application method of the Low Voltage Directive
and the product compatibility.

4.2.1 Standard subject to GOT

Standard applied to GOT : EN61131-2 Programmabl e controllers - Equipment

requirements and tests

EN60950-1 Safety of In formation Technology Equipment

4.2.2 Power supply

The insulation specification of the GOT was designed assuming
installation category II. Be sure to use the installation category II power
supply to the GOT.
The installation category indicates the durability level against surge
voltage generated by lightning strike.
Category I has the lowest durability; category IV has the highest
durability.

Category ICategory IICategory IIICategory IV

Category II indicates a power supply whose voltage has been reduced
by two or more levels of isolating transformers from the public power
distribution.

Installation category

4.2.3 Control panel

Because the GOT is open type equipment (device designed to be stored
within another device), be sure to use it only when installed in a control
panel.

(1) Shock Protection

In order to prevent those who are unfamiliar with power facility,
e.g., an operator, from getting a shock, make sure to take the
following measures on the control panel.
(a) Store the GOT within the control panel locked, and allow only

those who are familiar with power facility to unlock the panel.

(b) Build the structure in order that the power supply will be shut off

when the control panel is opened.

(2) Dustproof and waterproof features

The control panel also provides protection from dust, water and
other substances. Insufficient ingression protection may lower the
insulation withstand voltage, resulting in insulation destruction.
The insulation in the GOT is designed to cope with the pollution
level 2, so use in an environment with pollustion level 2 or better.

Pollution level 1: An environm ent where the air is dry and conductive

Pollution level 2: An environm ent where conductive dust does not

Pollution level 3: An environment where conductive dust exits and

Pollution level 4: Continuous con ductivity may occur due to rain, snow,

dust does not exist.

usually exist, but occasional temporary condu ctivity
occurs due to the accumulated dust.
Generally, this is the level for inside the control panel
equivalent a control room or on the floor of a typical
factory.

conductivity may be generated due to t he accumulated
dust.
An environment for a typical factory floor.

etc. An outdoor environment.

4.2.4 Grounding

The following are applicable ground terminals. Use them in the grounded
state.
Be sure to ground the GOT for ensuring the safety and complying with
the EMC Directive.

Functional grounding : Improves the noise resistance.

4.2.5 External wiring

(1) External devices

When a device with a hazardous voltage circuit is externally
connected to the GOT, select a model which complies with the
Low Voltage Directive's requirements for isolation between the
primary and secondary circuits.

(2) Insulation requirements

Dielectric withstand voltages are shown in the following table.
Reinforced Insulation Withstand Voltage
(Installation Category II, source : IEC664)

Rated voltage of hazardous

voltage area

150 VAC or below 2500V

300 VAC or below 4000V

Surge withstand voltage (1.2/50 s)

5. INSTALLATION

5.1 Control Panel Inside Dimensions for
Mounting GOT

Install the GOT on the control panel out of the way for the equipment
inside the control panel. Do not install the GOT and the unit in prohibited
areas for the installation.

Point

Applicable cable
Some cables may need to be longer than the specified dimensions when connecting to the
GOT. Therefore, consider the connector dimensions and bending radius of the cable as
well for installation.

5.2 Panel Cutting Dimensions

Make an installation hole on the control panel with the dimensions shown
below.
Make space of 10mm above and below the hole respectively for the
installation fittings.

A

5.3 Mounting Position

When mounting the GOT, the following clearances must be maintained
from other structures and devices.
Depending on the units and cables connected to the GOT, clearances
more than the described dimensions can be required.
Therefore, consider the connector dimensions and bending radius of the
cable as well for installation.
For the lead-in allowance for cables at the bottom of the GOT, refer to
the GT16 User’s Manual (Hardware) .

According to the dimensions in the following table, leave clearances
between the GOT and the other devices. The values enclosed in square
brackets apply to the case where no other equipment generating
radiated noise (such as a contactor) or heat is installed near the GOT.
However, keep the ambient temperature of the GOT to 55°C or lower.

*Panel thickness : 2 to 4 mm (0.08 to 0.16 inch)

GT1695M-X

B

GT1685M-S

GT1675M-S
GT1675M-V
GT1675-VN
GT1672-VN
GT1665M-S
GT1665M-V
GT1662-VN

GT1655-V

GOT

A[mm] (inch)

383.5 (15.10)

+2 (0.08)
0 (0)

302 (11.89)

+2 (0.08)
0 (0)

289 (11.38)

+2 (0.08)
0 (0)

227 (8.94)

+2 (0.08)
0 (0)

153(6.02)

+2 (0.08)
0 (0)

B

C

DE

A

Panel thickness: 2 to 4mm

(0.08 to 0.16 inch)

B[mm] (inch)

282.5 (11.12)

+2 (0.08)
0 (0)

228 (8.98)

+2 (0.08)
0 (0)

200 (7.87)

+2 (0.08)
0 (0)

176 (6.93)

+2 (0.08)
0 (0)

121(4.76)

+2 (0.08)
0 (0)

GT1665M-S
GT1665M-V
GT1662-VN

50(1.97) or

more
[36(1.42)
or more]

73(2.87) or

more

50(1.97) or

more

*1

*2

*3

*2*3

*3

*2

50(1.97) or

more
[36(1.42)
or more]

Unit : mm(inch)

GT1675M-S

Item

GOT only

Bus connection unit
is fitted
Serial
communication unit
fitted
RS-422 Conversion
unit is fitted
CC-Link
communication unit
(GT15-J61BT13)
fitted

MELSECNET/H
communication unit
(coaxial) fitted

MELSECNET/H
communication unit
(optical) fitted

CC-Link IE
Controller Network
communication unit
fitted

CC-Link IE Field

A

Network
communication unit
fitted
Video input unit

*4

fitted
RGB input unit

*4

fitted
Video/RGB input unit

*4

fitted
RGB output unit

*4

fitted
Multimedia unit

*4

fitted

Printer unit fitted

CF card unit

CF card extension
unit

Sound output unit

B

(When the CF card is
not used)

C

(When the CF card is
used)

D

E

*1: This value differs depending on the cable used.

Please contact your local Mitsubishi Electr ic System & Service Co., Ltd.
The value indicated in the table is a reference value.

*2: This value is for use of the coaxial cable 3C-2V (JIS C 3501).

For specifications of the cable, refer to the GOT1000 Series Connection
Manual for GT Works3 and a controller used.

*3: This value differs depending on the cable used .

If the bending radius of the cable used is greater than the value specified
above, apply the value of the cable used.

*4: The unit cannot be used for the GT1675-V, GT1672-V, GT1662-V, and

GT1655-V.

*5: Dimension when no battery is used.

If a battery is used, the dimension when a CF card is used is required.

Point

Refer to GT16 User’s Manu al (Hardware) for details of the Control Panel Ins ide
Temperature and Mounting Angle, Installation Procedure of each GOT.

GT1695M-X GT1685M-S

50(1.97) or more

[20(0.79) or more]

50(1.97) or

more

50(1.97) or more [20(0.7 9) or more]

50(1.97) or

more
[20(0.79)
or more]

50(1.97) or more [20(0.79) or more]

50(1.97) or more [20(0.7 9) or more]

50(1.97) or more [20(0.79) or more]

50(1.97) or more [20(0.79) or more]

50(1.97) or more [20(0.79) or more]

50(1.97) or more [20(0.79) or more]

50(1.97) or more [20(0.79) or more]

50(1.97) or more

[20(0.79) or more]

50(1.97) or more [20(0.7 9) or more]

GT1675M-V
GT1675-VN
GT1672-VN

50(1.97) or

more
[26(1.02)
or more]

51(2.01) or

63(2.48) or

more

more

50(1.97) or

50(1.97) or

more

more

[24(0.94)

[33(1.30)

or more]

or more]

50(1.97) or

more
[26(1.02)
or more]

80 (3.15) or more [20 (0.79) or more]

50(1.97) or more [20(0. 79) or more]

100(3.94) or more [20 (0.79) or more]

GT1655-V

61(2.40) or

more

50(1.97) or

more

49(1.93) or

more

-

50(1.97) or

more

[24(0.94)

or more]

64(2.52) or

more

79(3.11) or

more

57(2.24) or

more

-

-

-

-

-

50(1.97) or

more

[29(1.14)

or more]

50(1.97) or

more

[20(0.79)

or more]

50(1.97) or

moreExternal I/O unit

50(1.97) or

more

[20(0.79)
or more]
100(3.94)

or more

Unité : mm (pouce)

GT1675M-S

GT1665M-S

GT1675M-V

GT1665M-V

GT1675-VN

GT1662-VN

GT1672-VN

50 (1,97)

50 (1,97)

ou plus

ou plus

[26 (1,02)

[36 (1,42)

ou plus]

ou plus]

51 (2,01)

63 (2,48)

ou plus

50 (1,97)

ou plus

[33 (1,30)

ou plus]

50 (1,97)

ou plus

[26 (1,02)

ou plus]

73 (2,87)

ou plus

50 (1,97)

ou plus

*1

*2

*3

*2*3

*3

*2

50 (1,97)

ou plus

[36 (1,42)

ou plus]

ou plus

50 (1,97)

ou plus

[24 (0,94)

ou plus]

80 (3,15) ou plus [20 (0,7 9) ou plus]

50 (1,97) ou plus [20 (0,7 9) ou plus]

100 (3,94) ou plus [20 (0, 79) ou plus]

GT1655-V

61 (2,40)

ou plus

50 (1,97)

ou plus

49 (1,93)

ou plus

-

50 (1,97)

ou plus

[24 (0,94)

ou plus]

64 (2,52)

ou plus

79 (3,11)

ou plus

57 (2,24)

ou plus

-

-

-

-

-

50 (1,97)

ou plus

[29 (1,14)

ou plus]

50 (1,97)

ou plus

[20 (0,79)

ou plus]

50 (1,97)

ou plus

50 (1,97)

ou plus
[20 (0,79)
ou plus]

100 (3,94)

ou plus

*5

*4

GT1695M-X GT1685M-S

50 (1,97) ou plus [20

(0,79) ou plus]

50 (1,97)

ou plus

50 (1,97) ou plus [20 (0,79) ou plus]

50 (1,97)

ou plus

[20 (0,79)

ou plus]

50 (1,97) ou plus [20 (0,79) ou plus]

50 (1,97) ou plus [20 (0,79) ou plus]

50 (1,97) ou plus [20 (0,79) ou plus]

50 (1,97) ou plus [20 (0,79) ou plus]

50 (1,97) ou plus [20 (0, 79) ou plus]

50 (1,97) ou plus [20 (0,79) ou plus]

50 (1,97) ou plus [20 (0,79) ou plus]

50 (1,97) ou plus [20

(0,79) ou plus]

50 (1,97) ou plus [20 (0,79) ou plus]

5. INSTALLATION

5.1 Dimensions intérieures du tableau de
commande pour le montage du GOT

Installez le GOT sur le tableau de commande en laissant de l'espace
pour le dispositif à l'intérieur du tableau de commande. N'installez pas le
GOT et le module dans des zones où l'installation est interdite.

Point

Câble applicable
Certains câbles peuvent être plus longs que les dimensions spécifiées lors de la
connexion au GOT. Par conséquent, prenez également en compte les dimensions du
connecteur et le rayon de co urbure du câble pour l'installation.

5.2 Cotes de découpe du panneau

Faites un trou d'installation sur le tableau de commande avec les
dimensions indiquées ci-dessous.
Laissez un espace de 10mm au-dessus et sous le trou respectivement
pour les attaches de montage.

5.3 Position de montage

Lors du montage du GOT, laissez les espaces suivants pour les autres
structures et dispositifs.
En fonction des modules et des câbles connectés au GOT, il peut être
nécessaire de laisser des espaces plus importants que les dimensions
indiquées.
Par conséquent, prenez également en compte les dimensions du
connecteur et le rayon de courbure du câble pour l'installation.
Pour connaître l'espace à laisser pour les câbles sous le GOT, référez­vous au manuel GT16 User’s Manual (Hardware).

*5

Laissez les espaces entre le GOT et les autres dispositifs en fonction
des dimensions contenues dans le tableau suivant. Les valeurs entre
parenthèses s'appliquent au cas où aucun dispositif générant des
émissions sonores (comme un contacteur) ou de la chaleur n'est installé
près du GOT.
Toutefois, maintenez la température ambiante du GOT à 55°C ou moins.

A

*Épaisseur du panneau : 2 à 4mm ou moins

GT1695M-X

B

GT1685M-S

GT1675M-S
GT1675M-V
GT1675-VN
GT1672-VN
GT1665M-S
GT1665M-V
GT1662-VN

GT1655-V

GOT

A [mm] (pouce)

383.5 (15.10)

+2 (0.08)
0 (0)

302 (11.89)

+2 (0.08)
0 (0)

289 (11.38)

+2 (0.08)
0 (0)

227 (8.94)

+2 (0.08)
0 (0)

153(6.02)

+2 (0.08)
0 (0)

B[mm] (pouce)

282.5 (11.12)

+2 (0.08)
0 (0)

228 (8.98)

+2 (0.08)
0 (0)

200 (7.87)

+2 (0.08)
0 (0)

176 (6.93)

+2 (0.08)
0 (0)

121(4.76)

+2 (0.08)
0 (0)

B

C

DE

A

Épaisseur du panneau : 2 à 4mm

(0,08 à 0,16 pouce)

Article

GOT uniquement

Unité de connexion de
bus encastrée

Module de
communication série
encastré

Unité de conversion
RS-422 encastrée

Module de
communication CC­Link (GT15-J61BT13)
encastré

Module de
communication
MELSECNET/H
(coaxial) encastré

Module de
communication
MELSECNET/H
(optique) encastré

Module de
communication réseau
de contrôleur CC-Link
IE encastré

Module de

A

communication réseau
de champ CC-Link IE
encastré

Module d'entrée vidéo

*4

encastré
Module d'entrée RGB

*4

encastré
Module d'entrée vidéo/

RGB encastré
Module de sortie RGB

*4

encastré
Module multimédia

*4

encastré

Imprimante encastrée

Module de carte CF

Module d'extension de
carte CF

Module d'E/S externe
Module de sortie

acoustique

B

(Quand la carte CF
n'est pas utilisée)

C

(Quand la carte CF est
utilisée)

D
E

*1 : Cette valeur diffère selon le câble utilisé.

Contactez le bureau local Mitsubishi Electric System & Service Co., Ltd.
La valeur indiquée dans le tableau est une référence.

*2 : Cette valeur est utilisée pour le câble coaxial 3C-2V (JIS C 3501).

Pour connaître les spécifications du câble , référez-vous au GOT1000
Series Connection Manual for GT Works3 and a controller used.

*3 : Cette valeur diffère selon le câble utilisé.

Si le rayon de courbure du câble utilisé est supérieur à la val eur spécifiée
ci-dessus, appliquez la valeur du câble utilisé.

*4 : Le module ne peut pas être utilisé pour les modèles GT1675-V, GT1672-V,

GT1662-V et GT1655-V.

*5 : Dimension quand aucune batterie n'est utilisée.

Si une batterie est utilisée, il est néces saire d'utiliser la dimension quand
une carte CF est utilisée.

Point

Référez-vous au manuel GT16 User’s Manual (Hardware) pour obtenir des
détails sur la température intérieure et l'angle de m ontage du tableau de
commande et sur la procédure d'installation de chaque GOT.

6. MAINTENANCE AND INSPECTION

Refer to the GT16 User's Manual (Hardware) for maintenance and
inspection for the GOT.

Warra nty

Mitsubishi will not be held liable for damage caused by factors found
not to be the cause of Mitsubishi; machine damage or lost profits
caused by faults in the Mitsubishi products; damage, secondary
damage, accident compensation caused by special factors
unpredictable by Mitsubishi; damages to products other than
Mitsubishi products; and to other duties.

For safe use

• This product has been manufactured as a general-purpose part for
general industries, and has not been designed or manufactured to
be incorporated in a device or system used in purposes related to
human life.

• Before using t he product for special purposes such as nuclear
power, electric power, aerospace, medicine or passenger
movement vehicles, consult with Mitsubishi.

• This product has been manufactured under strict quality control.
However, when installing the product where major accidents or
losses could occur if the product fails, install appropriate backup or
failsafe functions in the system.

Country/Region Sales office/Tel

U.S.A Mitsubishi Electric Automation Inc.
500 Corporate Woods Parkway Vernon Hills, IL 60061, U.S.A.
Tel : [phone]
Brazil MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda.
Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar
Paraiso, Sao Paulo, SP Brazil
Tel : [phone]
Germany Mitsubishi Electric Europe B.V. German Branch
Gothaer Strasse 8 D-40880 Ratingen, GERMANY
Tel : [phone]
U.K Mitsubishi Electric Europe B.V. UK Branch
Travellers Lane, Hatfield, Hertfordshire., AL10 8XB, U.K.
Tel : [phone]
Italy Mitsubishi Electric Europe B.V. Italian Branch
Centro Dir. Colleoni, Pal. Perseo-Ingr.2
Via Paracelso 12, I-20041 Agrate Brianza., Milano, Italy
Tel : [phone]
Spain Mitsubishi Electric Europe B.V. Spanish Branch
Carretera de Rubi 76-80,
E-08190 Sant Cugat del Valles, Barcelona, Spain
Tel : [phone]
France Mitsubishi Electric Europe B.V. French Branch
25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France
Tel : [phone]
South Africa Circuit Breaker Industries Ltd.
Private Bag 2016, ZA-1600 Isando, South Africa
Tel : [phone]
Hong Kong Mitsubishi Electric Automation (Hong Kong) Ltd.
10th Floor, Manulife Tower, 169 Electric
Road, North Point, Hong Kong
Tel : [phone]
China Mitsubishi Electric Automation (China) Ltd.
4/F Zhi Fu Plazz, No.80 Xin Chang Road,
Shanghai 200003, China
Tel : [phone]
Taiwan Setsuyo Enterprise Co., Ltd.
6F No.105 Wu-Kung 3rd.Rd, Wu-Ku Hsiang,
Taipei Hsine, Taiwan
Tel : [phone]
Korea Mitsubishi Electric Automation Korea Co., Ltd.
1480-6, Gayang-dong, Gangseo-ku Seoul
157-200, Korea
Tel : [phone]
Singapore Mitsubishi Electric Asia Pte, Ltd.
307 Alexandra Road #05-01/02,
Mitsubishi Electric Building, Singapore 159943
Tel : [phone]
Thailand Mitsubishi Electric Automation (Thailand) Co., Ltd.
Bang-Chan Industrial Estate No.111 Moo 4, Serithai Rd,
T.Kannayao, A.Kannayao, Bangkok 10230 Thailand
Tel : [phone]
Indonesia P.T. Autoteknindo Sumber Makmur
Muara Karang Selatan, Block A/Utara
No.1 Kav. No.11 Kawasan Industri Pergudangan
Jakarta - Utara 14440, P.O.Box 5045 Jakarta, 11050 Indonesia
Tel : [phone]
India Messung Systems Pvt, Ltd.
Electronic Sadan NO:III Unit No15, M.I.D.C Bhosari,
Pune-411026, India
Tel : [phone]
Australia Mitsubishi Electric Australia Pty. Ltd.
348 Victoria Road, Rydalmere, N.S.W 2116, Australia
Tel : [phone]

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry
of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice.
Printed in Japan, October 2014.