FX2N-32CCL-NP CC-Link SYSTEM LOCAL BLOCK
HARDWARE MANUAL
JY992D96001A
This manual contains text, diagr ams and e x planations which will guide t he reader in t he correct installat ion
and operation of the FX
2N
-32CCL-NP CC-Link SYSTEM LO CAL BLOCK. It sh ould be read and
understood before attempting to install or use the unit. Fur ther information can be found in the FX series
PLC hardware manuals.
Note’s on the symbology used in this manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the user’s personal safety and protect the integrity of the equipment.
Whenever any of the following symbols are encountered, its associated note must be read and
understood. Each of the symbols used will now be listed with a brief description of its meaning.
Hardware warnings
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property damage.
1. INTRODUCTION
The FX2N-32CCL-NP is the interface block that connects the FX series PLC to the CC-Link system.
It is connected as a local station.
Master station .................S tation which controls the remote I/O station, remote device station, and local
stations
Remote I/O station..........Remote station which handles only on/off data
Remote device station ....Remote station which handles both on/off data and numeric data
Local station. ...................Station which has a CPU and can communicate with the master station and
other local stations
Protocol interface
FX2N-232AW C-NP
R e m o te I/O s ta tio n
FX2N PLC
M aster S tation
AJ65BT-G 4
RS-422
RS-232C
Program m ing
softw are
Power supply
FX
2N
PLC
C C -Link
FX
2N
-3 2 C C L
-N P
FX2N-3 2 C C L -N P
Program cable
Program cable
1.1 Dimensions and Setting
Dimensions: mm (inches) MASS (Weight): 0.4 kg (0.88 lbs)
Number Name Description
1) LED
indicators 1
LED
name
Description
RUN
ON : Module is normal.
OFF: Watchdog timer error has occurred.
ERR.
Indicates the communication status with
the stations set in the parameters.
ON : Communication error has
occurred in all stations.
Flashing : Communication error has
occurred in some stations.
L RUN
ON : D ata link is being executed
(host station).
L ERR.
ON : Communication error has
occurred (host station).
Flashing : The settings of the switches 4)
to 7) are changed while the
power is ON.
2) Power indictor POWER ON : 24V DC is supplied from the outside.
3) LED
indicators 2
SW ERR. ON : Switch setting error has occurred. OFF ON
TEST 1
Test result indication OFF except during testTEST 2
TEST 3
LINE ERR.
ON : The cable is broken the transmission
route is affected by noise, etc.
SD ON : Data is being transmitted.
RD ON : D ata is being received.
4)
Station
number setting
switch
Sets the station number of the module. (Default setting at shipment: 00)
<Setting range>
Local station : 1 to 64
If "65" or larger number is set, the "SW" and "L ERR." LED indicators turn ON.
5) Mode setting
switch
Sets the operation status of the module. (Default setting at shipment: 0)
Number Name Description
0 Online Sets connection to data link.
1 (Unusable)
2 Offline Sets disconnection from data link.
3 (Unusable)
4 (Unusable)
5 (Unusable)
6 Hardware test
7 (Unusable) Setting error (The SW LED indicator turns ON.)
8 to A (Unusable) Used in PLC internal operations.
B to F (Unusable) Setting error (The SW LED indicator turns ON.)
6) Transmission
speed setting
switch
Sets the transmission speed of the module. (Default setting at shipment: 0)
Number Setting contents
0 156 kbps
1 625 kbps
2 2.5 Mbps
3 5 Mbps
4 10 Mbps
5 to 9 Setting error (The SW and L ERR. LED indicators turn ON.)
RUN
ERR.
L RUN
L ERR .
POW ER
SW ERR .
TEST 1
TEST 2
TEST 3
LINE ERR .
SD
RD
85(3.34)
90(3.5)
87(3.43)
9(0.35)
FX2N-3 2 C C L -N P
2-φ4.5
80(3.15)
75(2.95)
MITSUBISHI
8)
9)
10)
13)
12)
RUN
ERR.
L RUN
L ERR
SW ERR.
TEST 1
TEST 2
TEST 3
LINE ERR.
SD
RD
STATION NO.
×
10
×
1
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
MODE
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
B RATE
0
2
1
3
4
156K
625K
2.5M
5M
10M
1
2
3
4
5
6
7
8
9
0
Guidelines for the safety of the user and protection of the FX2N-32CCL-NP CC-Link
SYSTEM LOCAL BLOCK
• If in doubt at any stage during the installation of the FX2N-32CCL-NP CC-Link SYSTEM LOCAL
BLOCK always consult a professional electrical engineer who is qualified and trained to the local
and national standard s. If in doubt abo ut the o peration or us e of the F X2N-32CCL-NP CC-Link
SYSTEM LOCAL BLOCK please consult the nearest Mitsubishi Electric distributor.
• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to
understanding the text, not to guarantee operation. Mitsubishi Electric will accept no
responsibility for actual use of the product based on these illustrative ex amples.
• Owing to the very great variety in possible application of this equipment, you must satisfy
yourself as to its suitability for your specific application.
Industrial
automation
Elincom
Group
EuropeanUnion: www.elinco.eu
Russia:www.elinc.ru
2N
-32CCL-NP CC-Link
2N
-32CCL-NP CC-Link
Program m ing
softw are
RS-232C
Power supply
R e m o te I/O s ta tio n
1.1 Dimensions and Setting
Dimensions: mm (inches) MASS (Weight): 0.4 kg (0.88 lbs)
85(3.34)
10)
75(2.95)
2-φ4.5
FX2N -3 2 C C L -N P
SW ERR .
LINE ERR .
12)
RUN
ERR.
L RUN
L ERR .
POW ER
90(3.5)
80(3.15)
TEST 1
TEST 2
TEST 3
SD
RD
Number Name Description
1) LED
indicators 1
RUN
ERR.
RUN
LED
name
ON : Module is normal.
OFF: Watchdog timer error has occurred.
Indicates the communication status with
the stations set in the parameters.
ON : Communication error has
Flashing : Communication error has
ON : D ata link is being executed
L RUN
L ERR
ERR.
L RUN
ON : Communication error has
L ERR.
Flashing : The settings of the switches 4)
2) Power indictor POWER ON : 24V DC is supplied from the outside.
3) LED
indicators 2
SW ERR. ON : Switch setting error has occurred. OFF ON
TEST 1
SW ERR.
TEST 3
TEST 1
TEST 2
TEST 3
LINE ERR.
LINE ERR.
SD
SD ON : Data is being transmitted.
RD
Test result indication OFF except during testTEST 2
ON : The cable is broken the transmission
RD ON : D ata is being received.
Station
4)
Sets the station number of the module. (Default setting at shipment: 00)
number setting
switch
STATION NO.
10
×
1
×
5) Mode setting
switch
<Setting range>
Local station : 1 to 64
3
4
2
1
5
If "65" or larger number is set, the "SW" and "L ERR." LED indicators turn ON.
0
6
9
7
8
3
4
2
1
5
0
6
9
7
8
Sets the operation status of the module. (Default setting at shipment: 0)
Number Name Description
0 Online Sets connection to data link.
1 (Unusable)
2 Offline Sets disconnection from data link.
3 (Unusable)
MODE
4
3
2
1
0
F
E
D
5
6
7
8
9
A
B
C
4 (Unusable)
5 (Unusable)
6 Hardware test
7 (Unusable) Setting error (The SW LED indicator turns ON.)
8 to A (Unusable) Used in PLC internal operations.
B to F (Unusable) Setting error (The SW LED indicator turns ON.)
6) Transmission
speed setting
switch
B RATE
0
156K
1
625K
2
2.5M
3
5M
4
10M
Sets the transmission speed of the module. (Default setting at shipment: 0)
Number Setting contents
0 156 kbps
1 625 kbps
3
2
1
0
9
8
2 2.5 Mbps
4
5
6
3 5 Mbps
7
4 10 Mbps
5 to 9 Setting error (The SW and L ERR. LED indicators turn ON.)
87(3.43)
9)
8)
13)
MITSUBISHI
9(0.35)
Description
occurred in all stations.
occurred in some stations.
(host station).
occurred (host station).
to 7) are changed while the
power is ON.
route is affected by noise, etc.
24+
FX2N-32 C C L -N P
24-
FG
STATIO N
3
2
4
1
NO.
0
6
×10
9
7
8
3
2
4
1
0
6
1
×
9
7
SLD D G
DA
DB
8
5
4
6
3
7
2
1
0
A
F
MODE
B
E
C
D
3
2
B RATE
4
1
156K
0
0
6
9
625K
7
1
8
2.5M
2
5M
3
ON
12345678
10M
4
SW
ONOFF
1
--
2
---
3
-
HLD
4
CLR
41
5
6
-
-
7
----
8
Inside of top cover
Normal Error
ON OFF
OFF
ON OFF
OFF
ON OFF
OFF ON
ON OFF
ON OFF
RUN
ERR.
1)
L RUN
5
L ERR .
POW ER
5
2)
8
9
11)
5
7)
SW ERR .
TEST 1
TEST 2
TEST 3
3)
LINE ERR .
SD
RD
LED status
ON or
flashing
ON or
flashing
Number Name Description
7) Condition
setting switch
SW
OFF
1
2
3
HLD
CLR
4
1
5
6
4)
5)
6)
7
8
Sets the operation condition. (Default setting at shipment: All OFF)
Number Setting description Switch status
ON
ON
12345678
4
SW1 to
SW3
SW4 Input data status in data link faulty station
SW5 Number of occupied stations 4 1
SW6 to
SW8
8) Terminal block Connects dedicated CC-Link cables to enable data link. For the connection
method, refer to Section 2.3.
SLD DG DA DB
The terminals SLD and FG are connected inside.
9) Terminal block Connects the power supply to operate the master block.
24+
24-
FG
10) Extension bus
cable
11) Expansion
bus port
12) Program
port
Connects the PLC.
Connects an extension equipment.
A connector for program cable
13) DIN rail
mounting
DIN46277: DIN rail mounting groove of 35 mm (1.38") in width
groove
2. Installation and wiring
INSTALLATION PRECAUTIONS
• Use the module in the environment described in the HARDWARE MANUAL General Specification.
Do not use the PLC in a place with dust, soot, conductive dust, corrosive gas or combustible gas,
place exposed t o high temperature, c ondensation, wind or rain or place with vibration or impact.
Using the module outsid e the rang e of t he general specification may resul t in e lect rical shoc k, fire,
malfunctions, or may damage the PLC.
• When drilling screw holes or performing wiring, make sure that cutting chips, wire chips or
other foreign matter does not enter the ventilation window of the module.
Such matter may cause fire, failure or malfunction.
• When the installat ion work is completed, remove the dust protection sheet from the ventilation
window of the PLC.
If the sheet remains attached, it may cause fire, failure or malfunction.
• Securely connect extension cables to specified connectors.
Poor contact may cause malfunction.
WIRING PRECAUTIONS
• Before beginning any installation or wiring work, make sure all phases of the power supply
have been shut down from the outside.
Incomplete shutdown of the power supply phases may cause electrical shock or damage in the
module.
• Following an installation or wiring work, when turning on the power supply and operating the
PLC, make sure that the terminal cover provided as an accessory has been attached to the
module.
A missing cover may cause electrical shock.
• For the CC-Link system, use dedicated cables specified by the manufacturer.
The performance of the CC-Link system cannot be guaranteed with any cable other than the
ones specified by the manufacturer.
With wiring outside the specification range, normal data transfer cannot be guaranteed.
• Make sure to fix communication cables and power cables connected to the module by placing
them in the duct or clamping them.
Cables not placed in duct or not clamped may hang or shift, allowing them to be accidentally
pulled, which may result in malfunction or damage to the module and the cables.
• The number of times to disconnect/connect the program cable for FX
kept to a minimum.
LED status
Normal Error
ON OFF
OFF
ON or
flashing
ON OFF
OFF
ON or
flashing
ON OFF
OFF ON
ON OFF
ON OFF
RUN
ERR.
L ERR .
L RUN
POW ER
SW ERR .
TEST 1
TEST 2
TEST 3
LINE ERR .
SD
RD
×10
×
1
STATIO N
NO.
MODE
B RATE
1
3
2
4
156K
625K
2.5M
5M
10M
0
HLD
41
ONOFF
SW
1
2
3
--
---
4
5
6
7
8
-
----
-
CLR
FX2N-32 C C L -N P
0
1
2
3
4
5
6
7
8
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
12345678
ON
1)
2)
3)
4)
5)
6)
7)
11)
Inside of top cover
24+
24-
FG
SLD D G
DA
DB
2. Installation and wiring
INSTALLATION PRECAUTIONS
• Use the module in the environment described in the HARDWARE MANUAL General Specification.
Do not use the PLC in a place with dust, soot, conductive dust, corrosive gas or combustible gas,
place exposed t o high temperature, c ondensation, wind or rain or place with vibration or impact.
Using the module outsid e the rang e of t he general specification may resul t in e lect rical shoc k, fire,
malfunctions, or may damage the PLC.
• When drilling screw holes or performing wiring, make sure that cutting chips, wire chips or
other foreign matter does not enter the ventilation window of the module.
Such matter may cause fire, failure or malfunction.
• When the installat ion work is completed, remove the dust protection sheet from the ventilation
window of the PLC.
If the sheet remains attached, it may cause fire, failure or malfunction.
• Securely connect extension cables to specified connectors.
Poor contact may cause malfunction.
WIRING PRECAUTIONS
• Before beginning any installation or wiring work, make sure all phases of the power supply
have been shut down from the outside.
Incomplete shutdown of the power supply phases may cause electrical shock or damage in the
module.
• Following an installation or wiring work, when turning on the power supply and operating the
PLC, make sure that the terminal cover provided as an accessory has been attached to the
module.
A missing cover may cause electrical shock.
• For the CC-Link system, use dedicated cables specified by the manufacturer.
The performance of the CC-Link system cannot be guaranteed with any cable other than the
ones specified by the manufacturer.
With wiring outside the specification range, normal data transfer cannot be guaranteed.
• Make sure to fix communication cables and power cables connected to the module by placing
them in the duct or clamping them.
Cables not placed in duct or not clamped may hang or shift, allowing them to be accidentally
pulled, which may result in malfunction or damage to the module and the cables.
• The number of times to disconnect/connect the program cable for FX
2N
-32CCL-NP should be
kept to a minimum.
7) Condition
setting switch
Sets the operation condition. (Default setting at shipment: All OFF)
Number Setting description Switch status
ON OFF
SW1 to
SW3
(Unusable) Always OFF
SW4 Input data status in data link faulty station
Keep
(HLD)
Clear
(CLR)
SW5 Number of occupied stations 4 1
SW6 to
SW8
(Unusable) Always OFF
8) Terminal block Connects dedicated CC-Link cables to enable data link. For the connection
method, refer to Section 2.3.
The terminals SLD and FG are connected inside.
9) Terminal block Connects the power supply to operate the master block.
10) Extension bus
cable
Connects the PLC.
11) Expansion
bus port
Connects an extension equipment.
12) Program
port
A connector for program cable
13) DIN rail
mounting
groove
DIN46277: DIN rail mounting groove of 35 mm (1.38") in width
Number Name Description
HLD
1
SW
ON
CLR
4
OFF
ON
12345678
2
1
3
4
6
5
7
8
SLD DG DA DB
24+
24-
FG
Loading...