Mitsubishi Electronics FFT9905SKJHFW User Manual

AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR
MODEL
USER'S GUIDE
FFT9905SKHFW
For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor.
CAUTION
 
The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock.
Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards.
 この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準に基づく 第二種情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、 この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こす ことがあります。  取扱説明書に従って正しい取り扱いをしてください。
高調波ガイドライン適合
Trademark
IBM, PC, PS/2, PS/V, Personal System/2 are registered trademarks of International Business Machines Corp. Apple Macintosh is a registered trademark of Apple Computer, Inc. Quadra is a trademark of Apple Computer, Inc. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. E
NERGY STAR
© 1998 MITSUBISHI ELECTRIC CORPORATION
is a U.S. registered mark.
RADIO INTERFERENCE REGULATIONS STATEMENT FOR U.S.A.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa­tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
THIS PRODUCT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS WITH SIGNAL CABLE SC-B102. USE IT TO REDUCE THE POSSIBILITY OF CAUSING INTERFERENCE TO RADIO, TELEVISION, AND OTHER ELECTRIC DEVICES.
NO USER SERVICEABLE PARTS INSIDE. DO NOT ATTEMPT TO MODIFY THIS EQUIPMENT. IF MODIFIED, YOUR AUTHORITY TO OPERATE THIS EQUIPMENT MIGHT BE VOIDED BY FCC.
WARNING!
This product is not designed for use in life support devices and Mitsubishi Electric corporation makes no representations to the contrary. Life support devices are those devices which are used to measure, diagnose, or evaluate the tissue, sys­tems or functions of the human body; or other devices employed to support or sustain life or good health.
MANUFACTURER DECLARATION FOR CE-MARKING:
We, Mitsubishi Electric Corp., declare under our sole responsibillity, that this product is in conformity with the following standards:
EN60950 EN55022 Class B EN50082-1 EN61000-3-2 EN61000-3-3
following the provisions of:
73/23/EEC Low Voltage Directive 89/336/EEC EMC Directive
As an E
NERGY STAR Partner, Mitsubishi Electric Corporation has determined that
this product meets the ENERGY STAR guidelines for energy efficiency.
2
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
Why do we have environmentally-labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem as far as computers and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since it is often routinely left running continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and Technical Development in Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product must be prepared for recycling and the manufacturer is obliged to have an environmental plan, which must be adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display after a certain period of inactivity shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example in respect of the reduction of electric and magnetic fields, along with physical and visual ergonomics and good usability.
3
In and after the middle of this page, you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development Unit S-114 94 Stockholm Sweden Fax: +46 8 782 92 07 E-mail (Internet): development@tco.se Current information regarding TCO'95 approved and labelled products may also be obtained via the Internet, using the address: http//www.tco-info.com/ TCO'95 is a co-operative project between
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cabling, casings and housings, and are added to delay the spread of fire. Up to 30 % of the plastic in a computer casing can consist of flame-retardant substances. These are related to another group of environmental toxins, PCB, and are suspected of giving rise to similar harm, including repro­ductive damage in fish-eating birds and mammals. Flame retardants have been found in human blood and researchers fear that they can disturb foetus development. Bio-accumulative* TCO'95 demands require that plastic components weighing more than 25 grammes must not contain frame retardants with organically bound chlorine or bromine.
Lead
can be found in picture tubes, display screens, solder and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant bio-accumulative* TCO'95 requirement permits the inclusion of lead, as no replacement has yet been developed.
Cadmium
is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant bio-accumulative* TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium. The colour-generating layers of display screens must not contain any cadmium.
Mercury
is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses. The relevant bio-accumulative* TCO'95 requirement states that batteries may no contain more than 25 ppm (part per million) of mercury.
demands require that no mercury is present in any of the electrical or electronic components concerned with the display unit.
CFCs (freons) are sometimes used for washing printed circuit boards and in the
manufacture of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of ultra-violet light with consequent increased risks of skin cancer (malignant melanoma). The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during manufacture of the product or its packaging.
* Bio-accumulative is defined as substances which accumulate within living organisms.
4
Diamond Scan 90e User’s Guide
CONTENTS
1. INTRODUCTION .................................................................................................. 6
1.1 Features ..................................................................................................... 6
1.2 Internal Preset Memory Capability ............................................................. 7
1.3 Power Management Function .................................................................... 7
1.4 DDC ........................................................................................................... 8
1.5 Location Considerations ............................................................................ 8
1.6 Cleaning Your Monitor ............................................................................... 8
1.7 Unpacking .................................................................................................. 9
1.8 Tilt/Swivel Base ......................................................................................... 9
Screen Position Adjustment ....................................................................... 9
1.9 Quick Operation Chart ............................................................................... 10
2. CONNECTING THE MONITOR ........................................................................... 11
2.1 AC Power Connection ............................................................................... 11
2.2 Signal Cable Connection ........................................................................... 11
2.2.1 Connecting to Any IBM VGA Compatible System .............................. 11
2.2.2 Connecting to An Apple Macintosh Centris, Quadra, and
Apple Macintosh II Family .................................................................. 12
2.2.3 Connecting to a Unix Workstation & Third Party Graphics Card ........ 12
3. USER CONTROLS ............................................................................................. 14
3.1 Control Names ........................................................................................... 14
3.2 Function ..................................................................................................... 14
4. OSD(On Screen Display) FUNCTIONS ............................................................... 16
4.1 Operation ................................................................................................... 17
4.2 POWER SAVE ........................................................................................... 23
5. TROUBLESHOOTING ......................................................................................... 24
6. SPECIFICATIONS ............................................................................................... 25
7. APPENDIX ........................................................................................................... 26
7.1 Monitor Signal Input Connector (DB9-15P) ............................................... 26
7.2 Serial Interface Input Connector (DIN-8P) For Serial Interface Function .. 26
7.3 SC-B102 Signal Cable ............................................................................... 27
7.4 Macintosh Adapter AD-A205 settings ........................................................ 28
Note : This manual is designed for use with Diamond Scan 90e color display monitor.
5
1
1
INTRODUCTION
Congratulations on your purchase of the Diamond Scan 90e high resolution color monitor. Mitsubishi designed this monitor to provide you with years of reliable trouble-free operation. Once again, thank you for selecting our product and welcome to Mitsubishi! This guide tells you how to connect, adjust and care for your Diamond Scan 90e monitor. This guide also provides technical specifications and instructions for troubleshooting any basic problems you may experience with your monitor.
1.1 Features
The Diamond Scan 90e is a 49.5cm/19"(46cm/18.0" Diagonal Viewable Image) intelligent, micropro­cessor-based monitor compatible with most analog RGB (Red, Green, Blue) display standards, including PS/V It provides crisp text and vivid color graphics with VGA, SVGA, XGA (non-interlaced), and most Macintosh compatible color video cards.
• The monitor’s wide auto-scanning compatibility range makes it possible to upgrade video cards or software without purchasing a new monitor.
• Digitally controlled auto-scanning is done using an internal microprocessor, for horizontal scan frequencies between 30kHz and 95kHz, and vertical scan frequencies between 50Hz and 152Hz. The microprocessor-based intelligence allows the monitor to operate in each frequency mode with the precision of a fixed frequency monitor.
• The monitor contains resident memory for pre-programmed screen display standards and is also capable of storing additional user adjustment parameters.
®
, PS/2®, Apple® Macintosh® Centris, Quadra, and Macintosh II family signals.
• The monitor is capable of producing a maximum horizontal resolution of 1600 dots and a maximum vertical resolution of 1200 lines typically. This display is well suited for windowing environments.
• Because of the analog signal inputs, the monitor can display an unlimited palette of colors that can be manually adjusted to suit your specific needs.
• The monitor has a power management function accorded to VESA-DPMS-standard. To save energy, the monitor must be connected to a system compliant with the VESA DPMS-standard. (Refer to your computer and/or video card instructions for proper operation.)
• To ensure ease of installation and ongoing use, the monitor features Moire Clear Function and On­Screen Display (OSD) of all monitor set-up and adjustment functions.
• For use in a variety of applications, the monitor complies with UL 1950, CSA C22.2 No.950 and EN60950 for safety, FCC Class-B, VCCI Class II and EN55022 Class-B for EMI, MPR-II, ISO 9241­3 and ISO 9241-8 for ergonomics. The monitor also complies with TCO'95 guideline for environmental safe use.
• Digital Chassis design for lighter, more compact enclosure and increased screen performance.
• Short neck (ZENTAN) CRT with 0.25mm pitch shadow mask, advanced-focus DQ-DAF (Double Quadrupole-Dynamic Astigmatism and Focus system) electron gun and high contrast optical­quality coating.
• The monitor complies with Video Electronics Standards Association (VESA specification. If your computer provides DDC1/2B(EDID) function, setup will be done automatically.
• USB-HUB unit KT-X406 is prepared as an optional parts for this monitor.
TM
) DDC1/2B(EDID)
6
1.2 Internal Preset Memory Capability
To minimize adjustment needs, the factory has preset popular display standards into the monitor, as shown in Table 1. If any of these display standards are detected, the picture size and center­ing are automatically adjusted. All of the factory presets may be overwritten by adjusting the user controls. The monitor is capable of automatically storing up to 6 additional display standards. The new display information must differ from any of the existing display standards by at least 1kHz for the horizontal scan frequency or 5Hz for the vertical scan frequency or the sync signal polarities must be different.
Table 1. Memory Buffer Factory Presets
Polarity
Resolution
640 x 480 N.I. 31.5 60.0 1024 x 768 N.I. 60.0 75.0 1280 x 1024 N.I. 80.0 75.0
1.3 Power Management Function
Fh (kHz)
Fv (Hz) H V
-­++ ++
The monitor has the power management function which reduces the power consumption of the monitor when not in use. There are three reduced power level modes.
Stand-by mode
When the horizontal sync signal is off after about 10 seconds, the monitor is switched to a stand-by mode. When the monitor is in stand-by mode, the screen is off. After the horizontal sync signal is restored, picture will be displayed immediately.
Suspend mode
When the vertical sync signal is off, after about 10 seconds the monitor is switched to a suspend mode which reduces the monitor power consumption to less than 15W. When the monitor is in suspend mode, the screen is off and the power indicator will change to amber. After the vertical sync signal is restored, picture will be displayed within a few sec­onds.
Power-off mode
When the horizontal sync signal and vertical sync signal are off, after about 10 seconds the monitor is switched to a power-off mode, which reduces the monitor power consumption to less than the power consumed at suspend mode above. When the monitor is in power-off mode, the screen is off, and the power indicator will change to amber. After both the sync signals are restored, picture will be displayed within several seconds.
7
1.4 DDC
The monitor includes the DDC1 and DDC2B feature. DDC (Display Data Channel) is a communi­cation channel over which the monitor automatically informs the host system about its capabilities (e.g. each supported resolution with its corresponding timing). DDC is routed through previously unused pins of the 15-pin VGA connector. The system will perform "Plug and Play" feature if both, monitor and host, implement the DDC protocol.
1.5 Location Considerations
When setting up and using the monitor, keep the following in mind:
* For optimum viewing, avoid placing the monitor against a bright background or where sunlight
or other light sources may reflect on the display area of the monitor; place the monitor just below eye level.
* Place the monitor away from strong magnetic or electromagnetic fields, such as
high capacity transformers, electric motors, large current power lines, steel pillars,
etc.... Magnetism can cause distortion in the picture and/or color purity.
* Avoid covering the slots or openings of the monitor. Allow adequate ventilation
around the monitor so the heat from the monitor can properly dissipate. Avoid putting the monitor into any enclosure that does not have adequate ventilation.
* Avoid exposing the monitor to rain, excessive moisture, or dust, as this can
cause a fire or shock hazard.
* Avoid placing the monitor, or any other heavy object, on the power cord.
Damage to the power cord can cause a fire or electrical shock.
* When transporting the monitor, handle it with care.
CAUTION
Keep your fingers away from the pivot area of the tilt/swivel base.
1.6 Cleaning Your Monitor
When cleaning the monitor, please follow these guidelines:
* Always unplug the monitor before cleaning. * Wipe the screen and cabinet front and sides with a soft cloth. * If the screen requires more than dusting, apply a household window cleaner to a soft cloth to
clean the monitor screen.
CAUTION
Do not use benzene, thinner or any volatile substances to clean the unit as the finish may be permanently marked. Never leave the monitor in contact with rubber or vinyl for an extended time period.
8
1.7 Unpacking
MITSUBISHI
AUTO-TRACKINGWITHDIGITALCONTROL COLORDISPLAYMONITOR
MODEL FFT9905SKHKW
Diamond Scan 90e
User's Guide
After you unpack the box you should have all of the items indicated in Figure 1. Save the box and packing materials in case you ship or transport the monitor. Complete and mail in warranty cards.
1
5
M
A U C
T
I
O
O
L
-
T
T
O
R
R
A  D
C
S
I
K
S
P
D
I N
L
G
A
U
Y
W
M
ia
M
I T
O
O
U
H
N
B
D
D
I
m
s
T
I
E
G
O
e
I
R
T
L
I
A
r
S
L
F
o
's
 C
F
O
T
n
N
G
H
T
9
R
u
9
d
O
L
0
i
I
d
5
S
S
e
K
H
c
K
W
a
n
9
0 e
2
6
1. Diamond Scan 90e Color Monitor
2. AC Power Cord
3. Signal Cable SC-B102
4. Macintosh Adapter AD-A205
5. User’s Guide
3
4
AD-A205
ON
1 2 3
M
I
4
T
S
5 6
U
B
I
S
H
I
6. Warranty-Set
Figure 1.
1.8 Tilt/Swivel Base
The monitor comes with a tilt/swivel base. This enables you to position the monitor to the best angle and tilt for maximum viewing comfort.
Screen Position Adjustment
Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case, as shown in Figure 2. You can adjust the monitor 45 degrees right or left, 10 degrees up or 5 degrees down, as shown below.
45
10
45
5
Figure 2.
9
1.9 Quick Operation Chart
To summarize the steps in connecting your computer and adapter with Diamond Scan 90e color monitor and setting the necessary controls and switches, refer to the chart below.
Connect the power cord to the Diamond Scan 90e color monitor and the signal cable between the Diamond Scan 90e and the graphics adapter.
Turn on the computer.
Turn on the Diamond Scan 90e color monitor.
Set the controls and switches.
OK
OK
If a problem appears.
See 5. TROUBLESHOOTING
See 2.1 AC Power Connection
2.2 Signal Cable Connection
See 3. USER CONTROLS
4. FUNCTION CONTROLS
If the problem persists.
Call for your authorized MITSUBISHI Product Support at 1-800-344-6352.
10
2 CONNECTING THE MONITOR
2
On the back of the monitor are four plug-in connections: one for the AC power cord, DB9-15P connector, BNC connector for video and a DIN-8P connector for the optional USB-unit.
2.1 AC Power Connection
One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitors auto-sensing power supply can automatically respond to the power supply input of 100­240V AC and 50/60Hz.
2.2 Signal Cable Connection
The attached video signal cable provides a DB9-15P connector for the VGA compatible analog RGB outputs on your computer. The RGB signal may be derived from an IBM® PS/2, or compat­ible Apple Macintosh built-in video. Most third party color cards can also be interfaced using the free Mitsubishi Apple adaptor available from your dealer.
2.2.1 Connecting to Any IBM VGA Compatible System
Figure 3 shows the SC-B102 cable connection to the Video Graphics Array (VGA) port in an IBM Personal System/2
1. Power off, the monitor and the computer.
2. Connect the one end of the SC-B102 cable to the DB9-15P connector on the VGA controller card.
3. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor.
4. Power on the computer, then the monitor.
5. After using the system, power off the monitor, then the computer.
Power Cord
®
Model 50, 60, 70 and 80, or any VGA compatible system.
Computer
VGA
Compatible
D-SUB
Serial
COMP.
RGB VD
HD
DB9-15P
CABLE SC-B102
Figure 3.
System
DB9-15P
CAUTION
The socket-outlet shall be installed near the equipment and shall be easily accessible. During servicing, disconnect the plug from the socket-outlet.
Méme si le moniteur est mis hors tension il reste toujours alimenté. La prise secteur devrait ainsi ètre facilement accssible en cas d'urgence.
11
2.2.2 Connecting to An Apple Macintosh Centris, Quadra, and Apple Macintosh II Family
Figure 4 shows the SC-B102 cable and AD-A205 Adapter to the video port in an Apple Macintosh.
1. Power off, both the monitor and the computer.
2. Set the DIP switches of Macintosh Adapter according to the setting chart. (See 7.4 Macintosh Adapter AD-A205 settings)
3. Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin connector on the Macintosh video port on the CPU or on the video board.
4. Connect the sub-miniature 15-pin (DB9-15P) end of AD-A205 Adapter to the SC-B102 cable.
5. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor.
6. Power on the Macintosh, then the monitor.
7. After using the system, power off the monitor, then the Macintosh.
Apple
Macintosh
Computer
Macintosh
Adapter
AD-A205
Serial
D-SUB
RGB VD
COMP.
HD
DB-15P DB9-15P
DB9-15P
Power Cord CABLE SC-B102 Please see APPENDIX (7.4 Macintosh Adapter AD-A205 settings).
Figure 4.
2.2.3 Connecting to a Unix Workstation & Third Party Graphics Card
Figure 5 shows the SC-B102 or 75 coaxial cable (not supplied) connection to the graphics video card (PC-CAD and workstation).
1. Power off, both the monitor and the computer.
2. Connect one end of the SC-B102 cable or the 75
coaxial cable to the output connector on
the CPU, or on the video board.
3. Connect the other end of the SC-B102 cable or the 75
coaxial cable to the DB9-15P
receptacle or the BNC receptacles on the back of the monitor.
4. Power on the computer, then the monitor.
5. After using the system, power off the monitor, then the computer.
High Resolution
Graphic Video Card
D-SUB
Serial
COMP.
RGB VD
HD
High Resolution
Graphic Video Card
75 coaxial cable
Power Cord
Please see next page about BNC connection.
DB9-15P
Cable SC-B102
Figure 5.
12
BNC CONNECTION
(1) IN CASE OF A COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC ON GREEN):
Connect the R, G and B video signals to the BNC receptacles on the back of the monitor.
D-SUB
RG B VD
Serial
COMP.
HD
(2) IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL:
Connect the R, G and B video signals and the Composite sync signal to BNC receptacles on rear panel, respectively.
D-SUB
RG B VD
Serial
COMP.
HD
(3) IN CASE OF SEPARATE HORIZONTAL AND VERTICAL SYNC SIGNALS:
Connect the R, G and B video signals and the horizontal and vertical sync signals to the BNC receptacles on the rear panel.
Serial
D-SUB
RG B VD
COMP.
HD
13
3
BNC/D-SUB OFF
ADJUST DEGAUSS
SELECT
3
USER CONTROLS
3.1 Control Names
See Figure 6 and 7 for the location of the following user controls and indicators. Each control is identified by number and is described individually on page 14.
FRONT
1. POWER SWITCH
2. POWER-ON INDICATOR
BNC/D-SUB OFF
3. INPUT CONNECTOR SELECT BUTTON
5. FUNCTION SELECT BUTTONS
SELECT
Figure 6
[How to use the front control panel] Press the button marked the control panel to open.To close, press it again.
6. FUNCTION ADJUST BUTTONS4. OSD OFF BUTTON
ADJUST DEGAUSS
7. DEGAUSS BUTTON
on
3.2 Function
1. POWER SWITCH: A push-on push-off switch for AC power.
2. POWER-ON INDICATOR: This indicator illuminates Green when AC power is on or Stand-
3. INPUT CONNECTOR SELECT BUTTON: Push the BNC/D-SUB button to select the input
4. OSD OFF BUTTON: A push type button that is used to turn off the OSD.
5. FUNCTION SELECT BUTTONS: Push the select buttons to choose one of the functions that
6. FUNCTION ADJUST BUTTONS: Push the adjust buttons to adjust the image on the screen
7. DEGAUSS BUTTON: A push type button that is used to eliminate possible color shading or
by mode, and illuminates Amber when suspend or power-off mode.
signal BNC or D-SUB.
is superimposed on the display screen.
that is selected via the function select buttons.
impurity.
14
REAR
AC POWER CONNECTOR
Serial
8. SERIAL INTERFACE CONNECTOR (DIN-8P)
D-SUB
D-SUB
Serial
COMP.
RG B VD
HD
SIGNAL INPUT CONNECTOR
(DB9-15P)
9. DC POWER OUTPUT CONNECTOR
RG B VD
COMP.
HD
SIGNAL INPUT CONNECTOR (BNC)
Figure 7
8. SERIAL INTERFACE CONNECTOR: The monitor has a DIN-8P connector for serial interface communication. This connector will be used for optional USB unit. For the information about connecting, please refer to the instruction which is included in each optional kit.
For further information about the optional USB kit, please contact your authorized MITSUBISHI dealer.
9. DC POWER OUTPUT CONNECTOR:
CAUTION
Do not connect the DC power connector with any models except MITSUBISHI USB unit.
15
4
4
OSD(On Screen Display) FUNCTIONS
(1) CONTRAST: Adjusts to the desired contrast level. (2) BRIGHTNESS: Adjusts to the black level of the screen. (3) COLOR-TEMPERATURE: Adjusts the color temperature of the screen image. (4) INFORMATION: Indicate current Scanning frequency and input Video signal port
(signal connector) (5) H-SIZE (Horizontal Size): Controls the horizontal size of the image on the screen. (6) H-PHASE (Horizontal Position): Controls the horizontal position of the image on the screen. (7) V-SIZE (Vertical Size): Controls the vertical size of the image on the screen. (8) V-POSITION (Vertical Position): Controls the vertical position of the image on the screen. (9) SIDE-BOW (Pincushion or Bow Amplitude): Straightens the left and right sides of the screen
image. (10)KEY STONE: Adjusts the parallelism of the left and right sides of the screen image. (11)PIN-BALANCE: Adjusts the curvature of the left and right sides of the screen image. (12)KEY-BALANCE: Adjusts the vertical slant or tilt of the screen image. (13)H-MOIRE: Adjusts the horizontal moire level on the screen. (14)V-MOIRE: Adjusts the vertical moire level on the screen. (15)ROTATION: Adjusts the rotation or twist of the picture. (16)GEOMETRY-RESET: Restore to factory preset following mode; H-SIZE, H-PHASE, V-SIZE, V-
POSI, SIDE-BOW, KEY STONE, PIN-BALANCE, KEY-BALANCE. (17)POWER-SAVE (ON/OFF): When adjusting ON, reduces the power consumption of the monitor when not
in use. (18)VIDEO LEVEL: Selects video levels 1.0V or 0.7V. (19)CLAMP-POSITION: Use this function to eliminate excessive green or white background that may
occur when both Sync-On-Green and external sync signals are applied to the
monitor. (20)USB PORT SELECT: Control upstream connection with using optional USB unit KT-X406.
16
4.1 Operation
Press any select button and control indicators will be superimposed on the display screen called 1st layer. Refer to Figure 6 for the location of the monitor function ( ) controls. Press the select buttons to choose one of the following controls. The indication of a function symbol changes to blue. When selected the function symbol of above OSD, press the adjust button ( or ), the OSD screen changes to following called 2nd layer. Then you can adjust each function by buttons.
1st OSD layer
2nd OSD layer
z z
z
VIDEO
CONT R AS T
CON T R A S T
SELECT
USB
CLAMP
Push any button
Push any button
LED : Stand-by, Normal : Green Suspend, Power-off : Amber
0%
9
Push any button
Push button to decrease contrast.
Push button to increase contrast.
17
2
10
6
4
1
5
1
11
3
7
Symbol of 1st OSD layer
1
CONTRAST
2
BRIGHTNESS
1
5
9
3
1
7
1
z
z
z
CONT R AS T
2nd OSD layer
CON T R A S T
LEVEL: 00 - 100%
4
8
12
6
1
VIDEO
1
CLAMP
8
9
1
USB
Press the Minus Adjust Button:
0%
9
To decrease the contrast.
0
2
Press the Plus Adjust Button:
To increase the contrast.
Press plus and minus buttons together, to restore to factory preset level.
BR I GH T N E S S
3
COLOR TEMPERATURE
CO L OR - T EM P ER AT U RE
LEVEL: 5000 - 9950K
4
INFORMATION
6
9 . 0 K H
C ONN E C T OR D - S UB
LEVEL: 00 - 100%
3
9
Z
@
7 5 H
Z
G
R
B
0%
9
0 0 K
To decrease the brightness.
To increase the brightness.
Press plus and minus buttons together, to restore to factory preset level.
To increase the red color level.
To increase the blue color level.
Data indicates color temperature (k:kelvin)
Indicate the horizontal frequency and the vertical frequency of input signal.
Indicate input connector.
18
Symbol of 1st OSD layer
5
H-SIZE
2nd OSD layer
Press the Minus Adjust Button:
Press the Plus Adjust Button:
6
H-PHASE
7
V-SIZE
8
V-POSITION
H - S I Z E
LEVEL: 00 - 100%
H - P H A S E
LEVEL: 00 - 100%
V - S I Z E
LEVEL: 00 - 100%
0%
9
To narrow the width of the image on the screen.
0%
9
To move the image to the left.
0%
9
To narrow the height of the image on the screen.
To expand the width of the image on the screen.
To move the image to the right.
To expand the height of the image on the screen.
9
SIDE-BOW
V - P OS I T I ON
LEVEL: 00 - 100%
S I D E - BOW
LEVEL: 00 - 100%
0%
9
To move the image down.
0%
9
To collapse the center of the image.
To move the image up.
To expand the center of the image.
19
Symbol of 1st OSD layer
10
KEYSTONE
2nd OSD layer
Press the Minus Adjust Button:
Press the Plus Adjust Button:
11
PIN-BALANCE
12
KEY-BALANCE
3
1
H-MOIRE
KE Y S T ONE
LEVEL: 00 - 100%
P I N - B AL A NCE
LEVEL: 00 - 100%
KE Y - B AL A NCE
LEVEL: 00 - 100%
H - MO I RE
LEVEL: 00 - 100%
0%
9
The decrease the width at the top of the screen image and to increase the width at the bottom.
0%
9
To move the top and bottom of the screen image to the right.
0%
9
To make the screen slant to the left.
The increase the width at the top of the screen image and to decrease the width at the bottom.
To move the top and bottom of the screen image to the left.
To make the screen slant to the right.
Press the plus or minus button to decrease the level of the horizontal moire wave.
0%
9
Press plus and minus buttons together, to restore to factory preset level.
4
1
V-MOIRE
V - MO I RE
LEVEL: 00 - 100%
Press the plus or minus button to decrease the level of the vertical moire wave.
0%
9
Press plus and minus buttons together, to restore to factory preset level.
20
Symbol of 1st
POWER - S A V E
O
F F ON
OSD layer
5
1
ROTATION
2nd OSD layer
Press the Minus Adjust Button:
Press the Plus Adjust Button:
6
1
GEOMETRY RESET
7
1
POWER-SAVE
z
z
z
8
1
VIDEO-LEVEL
VIDEO
RO T A T I ON
LEVEL: 00 - 100%
GEOME
T
C A NC E LP ROCEED
POWER - S A V E
V I
R Y - R E S E T
F FON
O
D EO - L E V E L
1 . 0 V
0 . 7
0%
9
To rotate to the left.
To rorate to the right.
Press plus and minus buttons together, to restore to factory preset level.
To cancel the geometry reset operation.
To reset the geometry data to factory adjusted condition.
MEMORY R ES E T
To select the constant power-on mode.
POWER - S A V E
F F ON
O
To select 1.0V of video input.
V
V I
D EO - L E V E L
1 . 0 V
0 . 7
V
To select the power-save mode.
To select 0.7V of video input.
V I
D EO - L E V E L
1 . 0 V
0 . 7
V
9
1
CLAMP-POSITION
CLAMP
CL
AMP
- P O S I T I O N
F R ON T
BACK
To clamp the video signal at the front of the H-Sync pulse.
AMP - P O S I T I O N
CL
F R ON T
BACK
21
To clamp the video signal at the back of the H-Sync pulse.
AMP - P O S I T I O N
CL
F R ON T
BACK
Symbol of 1st OSD layer
0
2
USB PORT SELECT
USB
1
2
ADJUST LOCK
1. Press the right of select button and minus of adjust button together, the "ADJUST LOCK" screen appears.
2. Press the plus button to lock on the OSD, and "LOCKED" character is indicated on 1st layer. You can operate OSD menu only CONTRAST, BRIGHTNESS and INFORMATION.
2nd OSD layer
USB S T A T US
L E A S E C H E CK
P
N I T OR
MO
N
NE C T I ON
CO
USB
IS S US P E NDED
SELECT
Press the Minus Adjust Button:
Press the Plus Adjust Button:
This "USB PORT SELECT" is prepared for optional part "USB-unit KT-X406" installed only.
Attention OSD screen is displayed without USB unit.
OR
For installing USB-unit, please read the manual of USB kit.
AD J US T M E N T - L OCK
I
S AB L E E N ABL E
D
( LO C K E D )
3. Press the minus button to lock off the OSD. You can operate OSD and all can be selected menu again.
22
4.2 POWER SAVE
POWER S A V E
NOTE
When the monitor has no sync signal or incorrect connection and the signal frequency is out of range, the following CAUTION comes on the screen. Check input signal, signal cable connection and signal frequency.
1. POWER SAVE IS OFF
When POWER SAVE is OFF and there is no sync signal, the following screen is displayed.
AT T E N T I ON
S I GNAL
NO
P
L E A S E C H E CK
P U T S I GNAL OR
I N
N
NE C T I ON .
CO
2. POWER SAVE IS ON
(1) When POWER SAVE is ON and there is
no sync signal, the following screen is displayed for 5 seconds.
(2) Before 2 seconds POWER SAVE function
works, the following screen is displayed. The power on indicator illuminates to change Amber.
AT T E N T I ON
S I GNAL
NO
P
L E A S E C H E CK
I N
P U T S I GNAL OR
N NE C T I ON .
CO
3. POWER SAVE IS ON OR OFF
When signal frequency is out of range, the following screen(ex. 96.8kHz/73Hz timing input) is displayed.
AT T E N T I ON
S
I GNAL F
I S
OU T OF RANGE .
P
L E A S E C H ANGE
S
I GNAL T I
RE QUENCY
M I NG .
23
5 TROUBLESHOOTING
5
Before calling your Authorized Product Support, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in SPECIFICATION 6 and APPENDIX 7.
PROBLEM
No picture
Abnormal picture
Display center shifts, or too small or too large of a display size
LED On-Green
LED Off
LED On-Amber
Un-stable picture
No green color with BNC
is missing,
ITEMS TO CHECK
Contrast and brightness controls.
Power switch.
AC power cord disconnected.
Signal cable disconnected.
BNC cables are misconnected or the green cable is disconnected.
Computer power switch.
Power management function is active.
BNC cables are misconnected.
Input signal frequency range is disagreement.
CGA MODE is not available. MDA MODE is not available. EGA MODE is not available.
BNC cables are misconnected. (Green and composite sync. connection is reversed)
Adjust H.SIZE, V.SIZE, H.PHASE, and V.POSITION with non-standard signals
Monitor may not be able to get full-screen image depend on signal. In this case, please select other resolution, or other vertical refresh timing.
Make sure you wait a few seconds after adjusting the size of the image before changing or discon­necting the signal or powering OFF the monitor.
LOCATION
Front (Adjust to the maximum brightness or push the reset button)
Front
Rear
Rear
Check the graphics adapter and cables
Computer
Check the power manage­ment function. (see P23)
Rear
Check the specification of graphics adapter and monitor
Rear
Front (OSD)
Front (OSD)
Display is not stable Display is dark
or too bright
BNC cables are misconnected. Input video signal level select is not at the appropriate position for your graphics adapter output.(0.7V or 1.0Vp-p)
24
Rear
Front (OSD)
6 SPECIFICATIONS
6
Size Mask type Shadow Mask Gun In-line Deflection angle 100°
CRT Phosphors Red, Green, Blue EBU
Dot pitch 0.25mm Face Plate Focusing method
INPUT SIGNAL Video 0.7 and 1.0Vp-p analog RGB
Sync Sync. on Green or separated H, V
INTERFACE Input Connector 5BNC, DB9-15P, DIN-8P(for USB kit)
Input Impedance 75 (video), 1k (sync) SCANNING Horizontal 30 - 95kHz FREQUENCY Vertical 50 - 152Hz RESOLUTION (HxV) WARM-UP TIME 30 minutes to reach optimum performance level
BRIGHTNESS 100cd/m2, standard full white video signal at 9300K + 8MPCD VIDEO AMPLIFIER 50Hz - 150MHz (typ.) BLANKING TIME Horizontal ≧2.3 µsec (typ.)
DISPLAY SIZE 340mm x 255mm (typ.) ratio 4:3, e.g. 1600dots x 1200lines COLOR 5000 ~ 9950K POWER SOURCE 100-240VAC ±10% 50/60Hz 150W (typ.)
OPERATING Temperature 5 - 35°C ENVIRONMENT Humidity 10 - 90%RH (without condensation) CABINET (W)18.5inch x (H)18.5inch x (D)16.1inch
WEIGHT 22.5kg (49.6lbs.) TILT/SWIVEL Tilt Angle -5° - +10° BASE Swivel Angle ±45°
REGULATIONS X-Ray DHHS, HWC
1600dots x 1200lines Non-Interlaced maximum addressable resolution format at 75Hz
Vertical 500 µsec (typ.)
< 130W (typ.: without USB-Unit KT-X406) >
(W)470mm x (H)468mm x (D)408 mm
Safety UL1950 (UL), CSA C22.2 No.950 (C-UL)
EMC FCC Class-B, DOC Class-B
Other CE-Marking, MPR-II
49.5cm/19" (46cm/18" Diagonal Viewable Image)
(medium short persistence) Crystal pigment
Anti-glare, Anti-reflection and Anti-static coating Double Quadrupole-Dynamic Astigmatism and Focus system (DQ-DAF)
sync. or Composite sync
EN60950 (TÜV-GS)
EN55022 Class-B, VCCI Class-2 EN50082-1, EN61000-3-2, EN61000-3-3
Röv vom 8.1, 1987
ISO 9241-3, ISO 9241-8 (TÜV-ERGO) TCO '95 ZH1/618 (TÜV-GS) International Energy Star Program Guidelines for the Suppression of Harmonics in Appliances and General-Use Equipment
25
7 APPENDIX
7
7.1 Monitor Signal Input Connector (DB9-15P)
(Female)
DB9-15P
5 4
10
15
14
2 1
3
9
13
67
8
11
12
MOUNTED ON THE REAR PANEL
DDC ............. DISPLAY DATA CHANNEL
SDA .............. SERIAL DATA
SCL .............. SERIAL CLOCK
NC ................ NO-CONNECTION
PIN ASSIGNMENT
Pin No. Signal
1 RED VIDEO 2 GREEN VIDEO
or COMPOSITE SYNC with GREEN VIDEO 3 BLUE VIDEO 4 GROUND 5 DDC GROUND 6 RED GROUND 7 GREEN GROUND 8 BLUE GROUND 9NC
10 SYNC GROUND 11 GROUND 12 SDA 13 HORIZONTAL SYNC
or COMPOSITE SYNC 14 VERTICAL SYNC(VCLK) 15 SCL
7.2 Serial Interface Input Connector (DIN-8P) For Serial Interface Function
(Female)
PIN ASSIGNMENT
Pin No. Signal
1 DTR (Data Terminal Ready) 2NC 3 TXD (Transmited Data) 4 GND 5 RXD (Receive Data)
DIN-8P
7
8
5
6
3
4
1
2
6 GND 7NC
MOUNTED ON THE REAR PANEL
8NC
NC......................... NO-CONNECTION
26
7.3 SC-B102 Signal Cable
10
11
14
12
15
PIN ASSIGNMENT AND SIGNAL LEVEL
Approx. 1.8m
DB9-15P DB9-15P (Male) (Male)
Wire : 5 coaxial
PIN ANALOG ASSIGNMENT
1
11 
8
12
131314
6 7
SIGNAL
1 RED 2 GREEN 3 BLUE 4 GROUND 5 DDC GROUND 6 RED GROUND 7 GREEN GROUND 8 BLUE GROUND 9NC 10 SYNC GROUND 11 GROUND 12 SDA 13 HORIZONTAL SYNC 14 VERTICAL SYNC(VCLK) 15 SCL
5
432
9
10
15
SIGNAL LEVEL
NC ..................... NO-CONNECTION
DDC: DISPLAY DATA CHANNEL SDA: SERIAL DATA SCL: SERIAL CLOCK
27
7.4 Macintosh Adapter AD-A205 settings
ON
The AD-A205 Macintosh Adapter allows you to take advantage of the built-in video capabilities of your Macintosh computer with the monitor. With it, you may select any available video mode via the DIP Switches.
Using the following chart, find the computer/resolution combination you wish to configure. There are alternate settings available for most computer / resolution combinations, but we recommend you set the factory preset timing. (see 1.2 Internal Preset Memory Capability)
The chart shows all available modes for Macintosh systems plus all possible combinations with monitor. Please be aware that not all Macintosh modes are capable of driving all Macintosh video modes.
DIP Switches
Display Monitor
1 2 3
MITSUBISHI
AD-A205
O
N
4
5 6
FF
O
Macintosh
N
O
In case of the computer corresponding to Multimode, you can select the resolution on your computer by setting the following switch. Please refer to instruction book of your computer about resolution setting.
21"Multimode
1,2,6 = Set DIP switches 1,2 and 6 "ON" (Supports 640X480@67Hz; 832X624@75Hz;
1024X768@75Hz; 1152X870@75Hz) or (Supports 640X480@67Hz; 832X624@75Hz; 1024X768@75Hz; 1152X870@75Hz; 1280X1024@75Hz ) or (Supports 640X480@67Hz; 832X624@75Hz; 1024X768@75Hz; 1152X870@75Hz; 1280X960@75Hz; 1280X1024@75Hz)
17"Multimode
1,2,5 = Set DIP switches 1,2 and 5 "ON" (Supports 640X480@67Hz; 832X624@75Hz;
1024X768@75Hz)
13"Multimode
1,2,5,6 = Set DIP switches 1,2,5 and 6 "ON" (Supports 640X480@67Hz;
832X624@75Hz)
28
Macintosh COMPUTER
RESOLUTION
640X480@60Hz
640X480@67Hz
800X600@56Hz
800X600@60Hz
800X600@72Hz
800X600@75Hz
832X624@75Hz
1024X768@60Hz
1024X768@70Hz
1024X768@72Hz
1024X768@75Hz
1024X768@75Hz
1152X870@75Hz
1280X960@75Hz
1280X1024@75Hz
Macintosh
IIci IIsi
1,2
Macintosh
LC,LC II
-or-
Performa
400,405, 410,430
3,4
1,2
AD-A205 Mac Adapter settings Chart
Macintosh
Performa
Macintosh
LC III,
LC 475
-or-
Performa
450,460, 466,467,
475,476
3,4 3,4
1,2
2,4
Macintosh
IIvi,llvx
-or-
600,
600 CD
1,2 1,2
LC 630,
Performa
630
-or-
Quadra
630
Macintosh
Quadra 700,900
Macintosh
Quadra 605,610, 650,800,
Centris
610,650
3,4 3,4 3,4 3,4 3,4
1,2 1,2
3,4 3,4
2,4
2,4
1,2,3,4 1,2,3,4
950
-or-
2,4
2,3
Macintosh
Quadra 840AV,
660AV
-or-
Centris
600AV
1,2
3,4
2,4
3,4
3,4
2,3
1,2,3,4
Apple
display
Card
48,824,
824GC
(revision B)
1,2
2,4#
1,2,3,4
Apple
display
Card 24AC
Power
Macintosh
Workgroup
Server
9150
3,4
1,2,6 1,2,5,6
1,2,6
1,2,5,6
1,2,6
1,2,6
1,2,6
1,2,6
Macintosh COMPUTER
RESOLUTION
640X480@60Hz
640X480@67Hz
800X600@56Hz
800X600@60Hz
800X600@72Hz
800X600@75Hz
832X624@75Hz
1024X768@60Hz
1024X768@70Hz
1024X768@72Hz
1024X768@75Hz
1024X768@75Hz
1152X870@75Hz
1280X960@75Hz
1280X1024@75
Hz
Power
-with-
DRAM
Macintosh
Video Card
Macintosh 6100,6100AV, 7100,7100AV,
8100,8100AV
Video Port
(HDl-45)
Power
7100, 8100,
-with-
DRAM
(DB-15)
Power
Macintosh
6100AV, 7100AV,
8100AV
-with-
Video Card
(DB-15)
3,4 3,4 3,4 1,2,5,6 3,4 3,4 3,4 3,4 3,4 3,4 3,4
1,2,5,6 1,2,6 1,2,6 1,2,5,6 1,2,6 1,2,6 1,2,6 1,2 1,2,5,6 1,2 1,2
3,4 3,4 1,2,5,6 3,4 3,4 3,4
1,2,5,6 1,2,6 1,2,6 1,2,5,6 1,2,6 1,2,6 1,2,6 2,4 1,2,5,6 2,4 2,4
3,4 3,4 3,4 3,4 3,4 3,4 3,4 3,4
1,2,6 1,2,6 1,2,6 1,2,6 1,2,6 2,3
1,2,6 1,2,6 1,2,6 1,2,6 1,2,6 1,2,3,4
Power
Macintosh
6200
AV
1,2,5,6 3,4 3,4 3,4
# = Must have revision B of ROM on video board
= Not working combination.
Power
Macintosh
7200
Power
Macintosh
7500,
8500
3,4 3,4 3,4
3,4 3,4 3,4 3,4 3,4
1,2,6 3,4
1,2,6 1,2,6
Power
Macintosh
9500
-with­ATl
Video Card
Macintosh PowerBook
160, 165,165C 180,180C
Macintosh PowerBook 520,520C,
540,540C
Macintosh PowerBook
Duo
210,230,
250,270C
-with-
Duo Dock
-or-
Duo
MiniDock
Macintosh PowerBook
Duo
210,230,
250,270C
-with-
Duo Dockll
29
CP871C144A90
MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE: MITSUBISHI DENKI BLD, MARUNOUCHI, TOKYO 100-0005 TELEX J24532 CABLE MELCO TOKYO
Loading...