Mitsubishi Electronics F940GOT User Manual

F940GOT Series(F94*GOT-*WD-E)

Installation Manual

JY992D94201E

This manual contains text, diagrams and explanations which will guide the reader in the correct installation, safe use and operation of the F94*GOT-*WD-E and should be read and understood before attempting to install or use the unit. Further information can be found in the associated manuals list below.

Specifications are subject to change without notice

Guidelines for the Safety of the User and Protection of the F94*GOT-*WD-E

This manual has been written to be used by trained and competent personnel. The definition of such a person or persons is as follows:

a) Any engineer using the product associated with this manual, should be of a competent nature,

trained and qualified to the local and national standards. These engineers should be fully aware of all aspects of safety with regards to automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and qualified to

the local and national standards.

c) All operators of the completed equipment should be trained to use that product in a safe and

co-ordinated manner in compliance to established safety practices.

The term ‘completed equipment’ refers to a third party constructed device which contains or uses

Note:

the product associated with this manual.

Note’s on the Symbols Used in this Manual

At various times through out this manual certain symbols will be used to highlight points of information which are intended to ensure the users personal safety and protect the integrity of equipment.

1) Indicates that the identified danger

cause physical and property damage.

WILL

2) Indicates that the identified danger could damage.

• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.

• Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

POSSIBLY

cause physical and property

Associated Manuals

Manual Name Manual Number Description

F940GOT Series

(F94*GOT-*WD-E) Installation Manual

GOT-F900

OPERATION MANUAL (describes GT Designer2)

GOT-F900 Series

Operation Manual

GOT-F900 Series

Hardware Manual (connection diagram)

GT Designer2 Version1

Operating Manual

GT Designer2 Version1

Reference Manual

GT Designer

Operating Manual

FX-PCS-DU/WIN-E

SOFTWARE MANUAL

F9GT-40FMB



User’s Manual

JY997D94201

JY992D09101

(separate volume)

JY992D94701

(separate volume)

JY992D94801

(separate volume)

(PDF files on CD-ROM included with product)

Included with the screen creation software

JY992D68301

(included with the screen

creation software)

JY992D98601

Describes the specifications, wiring, and installation of F940GOT Series graphic operation terminal. (hardware)

Describes the operation and use of the GOTF900 Series graphic operation terminals and GT Designer2.

Describes the operation and use of the GOTF900 Series graphic operation terminals, GT Designer and FX-PCS-DU/WIN-E.

Describes wiring and installation of the GOTF900 Series graphic operation terminals.

Describes the operation of GT Designer2 (SW*D5C-GTD2-E) and data transfer to the GOT-900 Series.

Describes the specifications and setting of object functions in GT Designer2 (SW*D5CGTD2-E).

Describes the operation of GT Designer (SW*D5C-GOTR-PACKE) and data transfer to the GOT-900 Series. (Refer to the help file)

Describes the operation of FX-PCS-DU/WINE screen creation software.

This manual contains explanations for installation and operating procedure of F9GT40FMB data transfer adapter.

Manual Name Manual Number Description

F9GT-40UMB



Manual

Indispensable manual

Either manual is necessary.



Refer if necessary, please.

JY992D74101

This manual contains explanations for installation and operating procedure of F9GT40UMB data transfer adapter.

Refer to the manual of the connected programmable controller for details concerning that unit.

1. Introduction

The F940GOT-*WD-E (hereafter called “GOT” or “F940GOT”) is to be mounted on the face of a control panel or operations panel, and connected to the programming port (CPU port) or the communication port (communication port) of a PLC. Various devices can be monitored and PLC data changed via the GOT screens. Several display screens are built-in to the GOT, and additional personalized screens can be created by the user.

1) The GOT can connect to MELSEC FX, A, QnA and Q PLCs as well as a host of third party manufactured units. Further information can be found in GOT-F900 Series Hardware Manual.

2) PLC user programs can be downloaded, uploaded and monitored using programming software GX-Developer or FX-PCS/WIN-E on a personal computer via the GOT. Further information can be found in the GOT-F900 Series Operation Manual.

3) Display screens are created using the following software.

Software Name Version

GT Designer2 SWD5C-GTD2-E

GOT-F900 and GOT-A900 Series (for Windows) screen creation software.

( indicates version)

GT Designer SWD5C-GOTR-PACKE ( indicates version)

FX-PCS-DU/WIN-E

GOT-F900 and GOT-A900 Series (for Windows) screen creation software. SW1-A edition of SW1D5C-GOTR-PACKE or later

GOT-F900 Series (for Windows) screen creation software. SW0PC-FXDU/WIN-E version 2.00 or later

1.1 Product Lists

Production Name Description

F940GOT-SWD-E Graphic operation terminal main unit

F940GOT-LWD-E

SWD: 8 colors LWD: White and black

Communication cable (GOT ↔ CPU port in FX

2NC

FX-50DU-CAB0

or FX The connector on the GOT side is wired straight.

series PLC)

Cable length is 3m (9' 10").

Communication cable (GOT ↔ CPU port in FX

2NC

FX-50DU-CAB0/EN

or FX

series PLC)

The connector on the GOT side is wired straight. Cable length is 3m (9' 10").

Communication cable (GOT ↔ CPU port in FX

FX-50DU-CAB0-**M

or FX The connector on the GOT side is wired straight.

series PLC)

2NC

** M is cable length. 1M: 1m (3' 3"), 10M: 10m (32' 9"), 20M: 20m (65' 7"),

30M: 30m (98' 5")

FX-40DU-CAB

Communication cable (GOT ↔ CPU port in FX, FX The connector on the GOT side is wired straight. Cable length is 3m (9' 10").

Communication cable (GOT ↔ CPU port in FX, FX

FX-40DU-CAB-**M

The connector on the GOT side is wired straight. ** M is cable length. 10M: 10m (32' 9"), 20M: 20m (65' 7"), 30M: 30m (98' 5")

QC30R2

Communication cable (GOT ↔ CPU port in Q series PLC) The connector on the GOT side is wired straight. Cable length is 3m (9' 10").

FX-232CAB-1 Data exchange cable (GOT ↔ Personal computer <9-pin D-sub>)

PM-20BL Battery for Alarm history, sampling and current time data reter tion.

F9GT-40PSC Transparent protection sheet for F940GOT (5 pieces)

F9GT-40LTS Backlight for F940GOT

F9GT-40UMB Data transfer adapter

F9GT-40FMB Data transfer adapter (Flash memory built in)

Caution

During abnormal communication (including cable breakages) when monitor is executed within the GOT, communication between the GOT and programmable controller CPU is interrupted. It is then impossible to operate switches or devices in the PLC through the GOT. Communication and normal operation resumes when the GOT system is correctly configured. DO NOT configure emergency stop or safety features to operate through the GOT, and be sure that there is no adverse consequences in the event of a GOT - PLC communications malfunction.

P L C

P r o g r a m m i n g p o r t

G O T

, FX0S, FX1S, FX0N, FX1N, FX2N

, A or QnA series PLC)

Note;

• Do not lay signal cables near high voltage power cables or allow them to share the same trunking duct, otherwise, effects of noise or surge induction are likely to take please. Keep a safe distance of more than 100 mm from these wires.

• Operate touch switches on the display screen by hand. DO NOT use excessive force, or attempt operate them with hard or pointed objects. The tip of a screw driver, pen or similar object for example may break the screen.

1.2 Dimensions and Each Part Name

Dimensions: mm (inches) MASS (Weight): 1 kg (2.2 lbs)

Accessory: Mounting brackets, Tightening bolt (M3, 6 bolts),

Packing seal for dust and water resistance

a )

c )

R S 2 3 2 C R S 4 2 2

1 2 0 ( 4 . 7 2 " )

5 7 ( 2 . 2 4 " )

i )

5 ( 0 . 2 0 " )

2 3 ( 0 . 9 1 " )

4 8 . 5 ( 1 . 9 0 " )

h )

6 . 5 ( 0 . 2 5 " )

1 0 ( 0 . 3 9 " )

1 6 2 ( 6 . 3 8 " )

d )

2 3 ( 0 . 9 1 " )

1 5 2 ( 5 . 9 8 " )

e )

2 3 ( 0 . 9 1 " )

1 0 ( 0 . 3 9 " )

2 4 V D C

b )

P O W E R

5 ( 0 . 2 0 " )

f )

1 4 0 ( 5 . 5 1 " )

1 3 0 ( 5 . 1 2 " )

g )

6 . 5 ( 0 . 2 5 " )

a) Display b) Mounting bracket hole c) Communication ports

Por t Description

RS-422

RS-422 Port for connecting either a PLC (including1:N connection) or communication (computer link) unit <9-pin D-sub>

RS-232C port for connecting eirher a personal computer, printer, bar-code reader

RS232C

or 1:N connection <9-pin D-sub>

d) Mounting bracket and tightening bolt e) PM-20BL battery f) Expansion interface g) DC power supply terminal (M3) h) Communication cable i) Packing seal

1 3 0 ( 5 . 1 2 " )

2. Specifications

2.1 General Specifications

Item Specifications

Operating Temperature

Storage Temperature -20 ~ 60 °C (-4 ~ 140 °F)

Humidity 35 ~ 85% Relative Humidity, No condensation

Operating atmosphere

Vibration Resistance

- intermittent vibration

Vibration Resistance

- Continuous vibration

Shock Resistance

Noise Immunity 1000 Vp-p, 1micro second, 30 ~ 100 Hz, tested by noise simulator

Dielectric Withstand Voltage 500 V AC > 1 min, tested between power terminals and ground

Insulation Resistance 5 MΩ > at 500 V DC, tested between power terminals and ground

Ground Grounding resistance of 100 Ω or less. (class D)

Protection IP 65F

0 ~ 50 °C (32 ~ 122 °F) [With expansion module: 0 ~ 40 °C (32 ~ 104 °F)]

Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electroconductive dust particles and must be no direct sunlight. (Same as for saving)

10 ~ 57 Hz: 0.075 mm Half Amplitude 57 ~ 150 Hz: 9.8 m/s

Acceleration

Sweep Count for X, Y, Z: 10 times (80 min. in each direction)

10 ~ 57 Hz: 0.035 mm Half Amplitude 57 ~ 150 Hz: 4.9 m/s

Acceleration

Sweep Count for X, Y, Z: 10 times (80 min in each direction)

Acceleration,

147m/s 3 times in each direction X, Y, and Z

HEAD OFFICE HIMEJI WORKS

: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN : 840, CHIYODA CHO, HIMEJI, JAPAN

Warranty

Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than Mitsubishi products; and to other duties. For the detailed warranty, refer to the GOT-F900 Series HARDWARE MANUAL [CONNECTION].

2.2 Power Supply Specifications

b )

a )

Items F94*GOT-SWD-E F94*GOT-LWD-E

Power Supply Voltage 24V DC, +10% -15%

Power Supply Ripple 200 mV or less

Current Consumption

Ratings: 410 mA at 24V DC Ratings: 390 mA at 24V DC

180 mA at 24 V DC when backlight is turned OFF

Fuse Fuse built-in GOT (impossible to change)

Max. Allowable Momentary Power Supply Failure period

Battery

5 ms; If less than 5 ms, the GOT will continue operation. If 5 ms or more, the GOT will shut down.

Built-in, PM-20BL type lithium battery. (Approximately 5 years battery life)

2.3 Screen Hardware Specifications

Items F94*GOT-SWD-E F94*GOT-LWD-E

Display Device STN colours liquid crystal

Resolution 320 × 240 (dot), 40 characters × 15 lines

Dot Pitch 0.36 mm (0.014") Horizontal × 0.36 mm (0.014") Vertical.

Effective Display Size 115 mm (4.53") × 86 mm (3.39"); 6 (5.7 inch) type

Number of Colours 8 colours White and Black

Life of liquid crystal

Backlight Cold cathode tube

Life of Backlight

Touch Keys Maximum 50 touch keys / screen, 20 × 12 matrix

Interface

RS-422 RS-422 1channel

RS-232C RS-232C 1channel

Number of Screens

User Memory Flash memory 512 KB (built-in)

• Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel. It is impossible to completely avoid this symptom, as the liquid crystal display comprises of a great number of display elements. Flickers may be observed depending on the display color. Please note that these dots appear due to its characteristic and are not caused by product defect.

• When the same screen is displayed for a long time, an incidental color or partial discoloration is generated on the screen due to heat damage, and it may not disappear.

• Using the GOT Backlight OFF function can prolong the life of the backlight. For details on the Backlight OFF function, refer to the following. GOT-F900 Series OPERATION MANUAL/GOT-F900 Series OPERATION MANUAL [GT Designer2 Version]

Approximately 50,000 hours (Operating temperature: 25 °C / 77°F)

40,000 hours or more (Operating temperature: 25 °C / 77°F)

User screen: 500 screens or less System screen: Allocated screens No. 1001-1030.

3. Installation

Note;

• Do not mount the GOT in an environment that contains dust, soot corrosive or conducive dust, corrosive or flammable gas, or expose the unit to high temperatures, dew condensation, direct sunlight, rain, wind or impact and vibration. If the GOT is used in such a place, electrical shock, fire, malfunction, damages or deterioration may occur.

• Never drop cutting chips or electric wire chips into the ventilation window of the GOT when drilling screw holes or performing wiring. Such chips may cause fire, failure or malfunction.

• Turn off the power before securely connecting any cables. Poor connection may cause malfunction.

The GOT is designed to be mounted in a panel. Install it using the following procedure:

1) Preparing the panel surface. On the panel surface, cut a rectangular mounting slot of the dimensions shown on the right. At this time, space of 10 mm is required at each of the top and the bottom of the slot, inside the panel for metal fixtures

S l o t t o b e c u t o n p a n e l

as shown in “4) Dimensions required inside the panel for installation”.

1 5 3 ( 6 . 0 2 " )

Note

Make sure that the thickness of the panel surface is no more than 5 mm (0.20").

+ 1 ( + 0 . 0 4 " ) 0

U n i t : m m ( i n c h e s )

+ 1

+ 0 . 0 4 "

1 2 1

( 4 . 7 6 " )

HEAD OFFICE HIMEJI WORKS

: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN : 840, CHIYODA CHO, HIMEJI, JAPAN

Warranty

2) Inserting the GOT into the panel surface

b )

a )

Attach the packing seal to the GOT, and insert the GOT from the front face of the panel surface.

a) Packing seal

b) GOT

c) Mounting slot

3) Fixing the GOT Put hooks of the mounting brackets (supplied) in to the mounting holes of the GOT. Tighten mounting bolts (also supplied) until the GOT is securely fixed. Fix mounting bolts in all four positions, above and below the GOT.

a) Clamping bolt

b) Mounting bracket

Note:

Make sure to tighten the clamping bolts with a torque of 0.3 ~ 0.5 Nm.

4) Dimensions required inside the panel for installation. When installing the GOT, make sure that the inner dimensions shown on the right are available.

a) PLC connection cable

b) Packing seal

4. Power Supply Wiring

Caution:

Cut OFF all external phases of power before installation or wiring to avoid electric shock or serious damage to the product.

Note:

• Wire the power supply using electric wires of 0.75 mm2 or more so that voltage drop will not occur. Use M3 size crimp style terminals. Securely tighten crimp-style terminals with a torque of 0.5 ~ 0.8 Nm so that errors can be avoided.

• Insure correct termination of the DC power source, incorrect connection may result in unit failure or serious damage to the GOT being burnt.

• Attach a fuse of 2 A to the 24V DC power supply.

• Perform Class D (100Ω or less) grounding with an electric wire of at least 1.25 mm Never perform common grounding of the GOT and a strong power system.

Note

• Use an external power supply to provide 24V DC. (The service power supply of the programmable controller cannot be used.)

• Even if instantaneous power interruption of less than 5 ms occurs, the GOT continues to operate. When power interruption for considerable period of time or voltage drop occurs, the GOT stops its operation. However, when the power supply is recovered, the GOT automatically restarts its operation. (The screen displayed just after recovery is determined by the working environment originally set.)

Grounding resistance 100Ω or less (class D)

1 7 2 ( 6 . 7 7 " )

1 4 0 ( 5 . 5 1 " )

2 4 V D C

a )

24V DC external power supply

5 7 ( 2 . 2 4 " )

5 ( 0 . 2 0 " ) o r l e s s

b )

Fuse (2A)

24V DC

PLC GOT

5. Expansion Module

a) F9GT-40UMB

The data transfer adaptor F9GT-40UMB is used to store the user screen data in the EPROM for user screen data FX-EPROM-4M to the flush memory in the GOT. (The user screen data can be written to the EPROM using the screen design software.) This adaptor is useful when the same screen data is transferred to two or more GOT units. For the operating procedure of F9GT-40UMB, please see the manual of F9GT-40UMB.

HEAD OFFICE HIMEJI WORKS

: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN : 840, CHIYODA CHO, HIMEJI, JAPAN

Warranty

b) F9GT-40FMB

F9GT-40FMB has a built-in flash memory and can transfer screen data when installed in the GOT. (When installed in OS versions either than 6.40, screen display is not available while transferring data from F9GT-40FMB to the GOT.) For operating procedures and specifications, refer to the manual for F9GT-40FMB.

6. Maintenance

Cautions:

• Correctly connect the battery for memory backup. Never charge, disassemble, heat, burn or short-circuit the battery. If the battery is handled in such a way, or fire may be caused.

• Always power OFF and remove the GOT from the panel before starting replacement of the backlight and battery. If this is not the case, the backlight may be dropped and cause injury, or electrical shock sustained.

• Never disassemble or modify the GOT. Disassembly or modification may cause failure, malfunction or fire. For repair, please, contact a service representative.

Note:

Turn OFF the power, before connecting/disconnecting cables. Connecting/disconnecting cables while the power is turned on will cause failure or malfunction caused.

When repairing liquid crystal screen, please, contact a service representative.

6.1 Battery Replacement

When the battery voltage drops, a control device (system information) set by the screen design software turns ON. The control device interlocks with an auxiliary relay in the PLC. It is recommended to provide a lamp while utilizing the output of the PLC so that voltage drop can be monitored outside the GOT. For details of control devices, refer to the GOT-F900 Series Operation Manual.

Note:

For approximately one month after the control device for battery voltage drop turns ON, the battery will back up the alarm history, sampling and the current time. When the control device (system information) turns ON, replace the battery (PM-20BL) as soon as possible. The screen data is stored in the flash memory. Even if the battery is totally worn out, the screen data will rema

6.1.1 Replacement Procedure

ven after severe battery voltage loss.

PM-20BL

1) Turn off the power to the GOT and remove the battery holder cover.

2) Remove the existing battery from the battery holder, and disconnect.

3) Within 30 seconds, connect a new battery.

4) Insert the new battery into the battery holder, and attach the cover.

6.2 Backlight Replacement

Replace the backlight F9GT-40LTS using the following procedure.

Note: Removing Rear Panel

If the rear panel is pulled using an excessive force, the cable connecting the rear panel and the front panel may be disconnected or the PCB may be damaged. Be careful.

6.2.1 Replacement procedure

a )

d )

1)Make sure that the power of the GOT is turned OFF. Remove the mounting screws (a) located at 4 corners, and slowly remove the rear panel.

2)Disconnect the backlight connector (b).

3)Remove the backlight F9GT-40LTS (c) from the backlight fixing holder (d). It is recommended to insert a screwdriver into the holder. Then, the backlight can be taken out easily.

4)Attach a new backlight F9GT-40LTS (c). Put it into the GOT

b )

by performing the steps 1) ~ 3) in the reverse order.

c )

Manual number : JY992D94201

Manual revision: E

Date : Sep. 2008