Mitsubishi AA150XT11 Specification
TENTATIVE
All information in this technical data sheet is tentative
and subject to change without notice.
15.0”XGA
TECHNICAL SPECIFICATION
AA150XT11
MITSUBISHI ELECTRIC Corp.
Date: Jun.27,’11
MITSUBISHI (1/26) AA150XT11_02_00
CONTENTS
No. Item Page
-- COVER 1
-- CONTENTS 2
1 APPLICATION 3
2 OVERVIEW 4
3 ABSOLUTE MAXIMUM RATINGS 5
4 ELECTRICAL CHARACTERISTICS 5, 6, 7
5 INTERFACE PIN CONNECTION 8, 9, 10
6 INTERFACE TIMING 11, 12, 13, 14, 15
7 BLOCK DIAGRAM 16
8 MECHANICAL SPECIFICATION 17, 18
9 OPTICAL CHARACTERISTICS 19, 20, 21
10 RELIABILITY TEST CONDITION 22
11 OTHER FEATURE 23
12 HANDLING PRECAUTIONS FOR TFT-LCD MODULE 24, 25, 26
MITSUBISHI (2/26) AA150XT11_02_00
1. APPLICATION
This specification applies to color TFT-LCD module, AA150XT11.
These specification papers are the proprietary product of Mitsubishi Electric Corporation
(“MITSUBISHI) and include materials protected under copyright of MITSUBISHI. No part of this
document may be reproduced in any form or by any means without the express written permission
of MITSUBISHI.
MITSUBISHI does not assume any liability for infringement of patents, copyrights or other
intellectual property rights of third parties by or arising from use of a product specified in this
document. No license, express, implied or otherwise, is granted under any patents, copyrights or
other intellectual property rights of MITSUBISHI or of others.
MITSUBISHI classifies the usage of the TFT-LCD module as follows. Please confirm the usage
before using the product.
(1) Standard Usage
Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
(2) Special Usage
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
(3) Specific Usage
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control systems,
life support systems and any other equipment. MITSUBISHI should make a contract that
stipulate apportionment of responsibilities between MITSUBISHI and our customer.
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should first contact MITSUBISHI sales representative for it's intended
use in writing.
MITSUBISHI has been making continuous effort to improve the reliability of its products.
Customers should implement sufficient reliability design of their application equipments such as
redundant system design, fail-safe functions, anti-failure features.
MITSUBISHI assumes no responsibility for any damage resulting from the use of the product that
does not comply with the instructions and the precautions specified in this document.
Please contact and consult a MITSUBISHI sales representative for any questions regarding this
product.
MITSUBISHI (3/26) AA150XT11_02_00
2. OVERVIEW
AA150XT11 is 15.0” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) modules
composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit or 8 bit digital data, 1024 × 768, 262k-color or 16.7M-color images are displayed
on the 15.0” diagonal screen. Input power voltage is 3.3 V for LCD driving.
The type of data and control signals are digital and transmitted via LVDS interface per Typ. 65
MHz clock cycle.
Driver circuit for LED backlight is not included in this module. General specifications are
summarized in the following table:
ITEM SPECIFICATION
Display Area (mm)
Number of Dots
Pixel Pitch (mm)
Color Pixel Arrangement RGB vertical stripe
Display Mode Normally white
Number of Color 262k(6 bit/color), 16.7M(8 bit/color)
Luminance (cd/m2) 1500
Viewing Angle (CR ≥ 10) −80~80° (H), −80~60° (V)
Surface Treatment Anti-glare and hard-coating 3H
Electrical Interface LVDS (6 bit/8 bit)
Viewing Direction
Module Size (mm)
Module Mass (g) 1290
Less gray scale reversal: 12 o'clock
304.1 (H) × 228.1 (V)
(15.0-inch diagonal)
1024 × 3 (H) × 768 (V)
0.297 (H) × 0.297 (V)
Higher Contrast ratio: 6 o'clock
326.0 (W) × 255.0 (H) × 16.6 (D)
Backlight Unit LED, edge-light, replaceable
Characteristic value without any note is typical value.
MITSUBISHI (4/26) AA150XT11_02_00
3. ABSOLUTE MAXIMUM RATINGS
g
ITEM SYMBOL MIN. MAX. UNIT
Power Supply Voltage for LCD VCC 0 4.0 V
Logic Input Voltage VI
−0.3
VCC+0.3 V
Backlight (LED) Current IF 0 180 mA
Operation Temperature (Panel)
Operation Temperature (Ambient)
Storage Temperature
Note 1,2)
T
Note 2)
T
Note 2)
T
op(Panel)
op(Ambient)
stg
−20
−20
−20
70 °C
70 °C
80 °C
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstg ≤ 40°C : 90%RH max. without condensation
Top,Tstg > 40°C : Absolute humidity shall be less than the value of 90%RH at 40°C without
condensation.
4. ELECTRICAL CHARACTERISTICS
(1) TFT- LCD Ambient Temperature : Ta = 25°C
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Power Supply Voltage for LCD VCC 3.0 3.3 3.6 V *1)
Power Supply Current for LCD ICC -- 410 700 mA *2)
Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC = +3.3 V
Logic Input Voltage
High VIH
Low VIL 0 --
*1) Power and signals sequence:
0.1 ms ≤ t1 ≤ 10 ms 200 ms
t2 ≤ 50 ms 200 ms ≤ t5
0 <
0 < t3
LCD Power Supply
ic Signal
Lo
Backlight Power Supply
≤ 50 ms 0 ≤ t6
0.1VCC
0.8×VCC
-- VCC V MODE, SC
0.2×VCC
≤ t4
VCC
0.9VCC
data
t2
t1
t5 t6
data: RGB DATA, DCLK, DENA, MODE, S C
t3
0.9VCC
0.1VCC
t4
V MODE, SC
0.1VCC
MITSUBISHI (5/26) AA150XT11_02_00
VCC-dip conditions:
1) When 2.6 V
≤ VCC < 3.0 V, td ≤ 10 ms
2) When VCC < 2.6 V
VCC-dip conditions should also follow the power and signals sequence.
VCC
3.0 V
2.6 V
td
*2) VCC = +3.3 V , f
= 48.4 kHz, fV = 60 Hz, f
H
= 65 MHz
CLK
Display image at typical power supply current value is 256-gray-bar pattern (8 bit), 768 line mode.
*3) Fuse
Parameter Fuse Type Name Supplier Remark
VCC FHC16322AD Kamaya Electric Co., Ltd. *)
*) The power supply capacity should be designed to be more than the fusing current.
(2) Backlight
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
-- (24) 30.5 V IF = 100 mA, Ta = 25°C, *2)
LED Voltage VF
-- -- 31.6 V IF = 100 mA, Ta = 0°C
-- -- 32.5 V
IF = 100 mA, Ta = −20°C
LED Current IF -- 100 110 mA Ta = 25°C, *1), *3)
LED Life Time LT 80,000 100,000 -- h
IF = 100 mA, Ta = 25°C
*4), *5), Continuous operation
[Note]
*1) Constant Current Drive
*2) The Voltage deviation between strings: |V
fMAX
– V
fMIN
| ≤ 2V
MITSUBISHI (6/26) AA150XT11_02_00
*3) LED Current measurement method
A
A
A
A
A
A
A
A
LCD
Module
C1
C2
C3
C4
C1
C2
C3
A
1
A
2
A
3
A
4
A
1
A
2
A
3
Power
Supply
Power
Supply
Power
Supply
Power
Supply
Power
Supply
Power
Supply
Power
Supply
C4
4
A
Power
Supply
*4) LED life time is defined as the time when the brightness becomes 50% of the initial value.
*5) The life time of the backlight depends on the ambient temperature. The life time will decrease
under high temperature.
MITSUBISHI (7/26) AA150XT11_02_00
5. INTERFACE PIN CONNECTION
V
(1) CN 1(Interface Signal)
Used Connector: DF14H-20P-1.25H(56) (HIROSE) or MSB240420HE (STM)
Corresponding connector: DF14-20S-1.25C (HIROSE) or P240420 (STM)
Pin
No.
Symbol
1 VCC
2 VCC
3 GND
4 GND
5
Link 0−
R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2
6 Link 0+ R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2 R0, R1, R2, R3, R4, R5, G0
7 GND
8
Link 1−
G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3
9 Link 1+ G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3 G1, G2, G3, G4, G5, B0, B1
10 GND
11
Link 2−
B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA
12 Link 2+ B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA B2, B3, B4, B5, DENA
13 GND
14
CLKIN− Clock − ←
15 CLKIN+
16 GND
17
Link3−
See: *2) R0, R1, G0, G1, B0, B1
18 Link3+ See: *2) R0, R1, G0, G1, B0, B1 R6, R7, G6, G7, B6, B7
19 MODE Low=ISP 6 bit compatibility mode
20 SC
Scan direction control ( Low = Normal , High = Reverse )
*1) Metal frame is connected to signal GND.
*2) Recommended wiring of Pin 17,18 (6 bit input)
Function(ISP 6 bit compatibility mode)
6 bit input 8 bit input
+3.3 V Power supply
+3.3 V Power supply
GND
GND
GND
GND
GND
Clock +
GND
Function(ISP 8 bit
compatibility mode)
←
←
←
←
R0, R1, R2, R3, R4, R5, G0
←
G1, G2, G3, G4, G5, B0, B1
←
B2, B3, B4, B5, DENA
←
←
←
R6, R7, G6, G7, B6, B7
High=ISP
8 bit compatibility mode
←
LVD S
transmitter
LOW data
Pin 17
Pin 18
or
680
620
CC
Ω
Pin 17
Pin 18
Ω
MITSUBISHI (8/26) AA150XT11_02_00
Loading...