Mitsubishi AA150XS01 Specification
Global LCD Panel Exchange Center
www.panelook.com
TENTATIVE
All information in this technical data sheet is tentative
and subject to change without notice.
15.0”XGA
TECHNICAL SPECIFICATION
AA150XS01
MITSUBIS HI ELECTRI C Corp.
Date: Jul.29,’10
MITSUBISHI
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Confidential (1/25) AA150XS01_02_00
www.panelook.com
Global LCD Panel Exchange Center
CONTENTS
www.panelook.com
No.
-- COVER 1
-- CONTENTS 2
1 APPLICATION 3
2 OVERVIEW 4
3 ABSOLUTE MAXIMUM RATINGS 5
4 ELECTRICAL CHARACTERIST ICS 5, 6
5 INTERFACE PIN CONNECTIO N 7, 8, 9
6 INTERFACE TIMING 10, 11, 12, 13, 14
7 BLOCK DIAGRAM 15
8 MECHANICAL SPECIFICATION 16, 17
9 OPTICAL CHARACT ERISTICS 18, 19, 20
Item Page
10 RELIABILITY TEST CO NDITION 21
11 OTHER FEATURE 22
12 HANDLING PRECAUTIONS FOR TFT-LCD MODULE 23, 24, 25
MITSUBISHI
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Confidential (2/25) AA150XS01_02_00
www.panelook.com
Global LCD Panel Exchange Center
1. APPLICATION
This specification applies to color TFT-LCD module, AA150XS01.
These specification papers are the proprietary product of Mitsubishi Electric Corporation
(“MITSUBISHI) and include materials protected under copyright of MITSUBISHI. No part of this
document may be reproduced in any form or by any means without the ex press written permission
of MITSUBISHI.
MITSUBISHI does not assume any liability for infringement of patents, copyrights or other
intellectual property rights of third parties by or arising from use of a product specified in this
document. No license, express, implied or otherwise, is granted under any patents, copyrights or
other intellectual property rights of MITSUBISHI or of others.
MITSUBISHI classifies the usage of the TFT-LCD module as follows. Please confirm the usage
before using the product.
(1) Standard Usage
Computers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
(2) Special Usage
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
(3) Specific Usage
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control systems,
life support systems and any other equipment. MITSUBISHI should make a contract that
stipulate apportionment of resp onsibilities between MITSUBISHI and our customer.
www.panelook.com
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should first contact MITSUBIS HI sales representative for it's intended
use in writing.
MITSUBISHI has been making continuous effort to improve the reliability of its products.
Customers should implement sufficient reliability design of their application equipments such as
redundant system design, fail-safe functions, anti-failure features.
MITSUBISHI assumes no responsibility for any damage resulting from the use of the product that
does not comply with the instructions and the precautions specified in this document.
Please contact and consult a MITSUBISHI sales representative for any questions regarding this
product.
MITSUBISHI
Confidential (3/25) AA150XS01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
2. OVERVIEW
AA150XS01 is 15.0” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) modules
composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applyi ng 6 bit o r 8 bit dig ital data, 1024u 768, 262k-col or or 16.7M-c olor imag es are display ed
on the 15.0” diagonal screen. Input power voltage is 3.3 V for LCD driving.
The type of data and control signals are digi tal and transmi tted via LV DS interf ace per Ty p. 65
MHz clock cycle.
Driver circuit for LED backlight is not included in this module. General specifications are
summarized in the following table:
ITEM SPECIFICATION
www.panelook.com
Display Area (mm)
Number of Dots 1024 u3 (H) u 768 (V)
Pixel Pitch (mm) 0.297 (H) u 0.297 (V)
Color Pixel Arran ge ment RGB vertical stripe
Display Mode Normally black
Number of Color 262k(6 bit/color) 16.7M(8 bit/color)
Luminance (cd/m2) 350
Viewing Angle (CR t10) 85~85° (H) 85~85° (V)
Surface Treatment Anti-glare and hard-coating 3H
Electrical Interface LVDS (6 bit/8 bit)
Module Size (mm) 326.0 (W) u 255.0 (H) u 16.6 (D)
Module Mass (g) 1260
Backlight Unit LED, edge-light, replaceable
Characteristic value without any note is typical value.
304.1 (H) u 228.1 (V)
(15.0-inch diagonal)
MITSUBISHI
Confidential (4/25) AA150XS01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
g
g
y
www.panelook.com
3. ABSOLUTE MAXIMUM RATINGS
ITEM SYMBOL MIN. MAX. UNIT
Power Supply Volt age for LCD VCC 0 4.0 V
Logic Input Voltage VI 0.3 VCC+0.3 V
Backlight (LED) Current IF 0 180 mA
Operation Temperature (Panel)
Operation Temperature (Ambient)
Storage Temperature
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstgd 40qC : 90%RH max. without condensation
Top,Tstg > 40qC : Absolute humidity shall be less than t he value of 90%RH at 40qC without
condensation.
Note 1,2)
T
Note 2)
T
Note 2)
T
op(Panel)
op(Ambient)
stg
20 70 °C
20 70 °C
20 80 °C
4. ELECTRICAL CHARACTERISTICS
(1) TFT- LCD Ambient Temperature : Ta = 25°C
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Power Supply Volt age for LCD VCC 3.0 3.3 3.6 V *1)
Power Supply Current for LCD ICC -- 550 1100 mA *2)
Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC = +3.3 V
Logic Input Voltage
*1) Power and signals sequence:
LCD Power Supply
ic Signal㩷
Lo
High VIH 0.8uVCC -- VCC V MODE, SC
Low VIL 0 -- 0.2uVCC V MODE, SC
t1
d 10 ms 200 ms d t4
0
0 t3
d 50 ms 200 ms d t5
t2
d 50 ms 0 d t6
VCC
0.9VCC
data
0.1VCC
0.9VCC
0.1VCC
0.1VCC
t2
t1
ht Power Suppl
Backli
t5 t6
data: RGB DATA, DCLK, DENA, MODE, SC
MITSUBISHI
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Confidential (5/25) AA150XS01_02_00
t3
t4
www.panelook.com
Global LCD Panel Exchange Center
VCC-dip conditions:
1) When 2.6 V
d VCC < 3.0 V, t d d 10 ms
2) When VCC < 2. 6 V
VCC-dip conditions should also follow the power and signals sequence.
www.panelook.com
VCC
3.0 V
2.6 V
td
*2) VCC = +3.3 V , fH= 48.4 kHz, fV= 60 Hz, f
= 65 MHz
CLK
Display image at typical power supply current value is 256-gray-bar pattern (8 bit), 768 line mode.
*3) Fuse
Parameter Fuse Type Name Supplier Remark
VCC FHC16322AD Kamaya Electric Co., Ltd. *)
*) The power supply capacity should be designed to be more than the fusing current.
(2) Backlight
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
-- (24) 31.1 V IF = 120 mA, Ta = 25°C, *2)
LED Voltage VF
-- -- 32.2 V IF = 120 mA, Ta = 0°C
-- -- 33.1 V IF = 120 mA, Ta = 20°C
LED Current IF -- 120 130 mA Ta = 25°C , *1), *3)
LED Life Time LT 80,000 100,000 -- h
IF = 120 mA, Ta = 25°C
*4), *5), Continuous operation
[Note]
*1) Constant Current Drive
*2) The Voltage deviation between strings: |V
fmax
– V
fmin
| d 2V
*3) LED Current measurement method
LCD
Module㩷
C1
A1
C2
A2
C3
A3
C4
A4
A
A
A
A
Power
Supply
Power
Supply
Power
Supply
Power
Supply
*4) LED life time is defined a s the time when the brightness becomes 50 % of the initia l va lue.
*5) The life time of the backlight depends on the ambient temperature. The life time will decr ease
under high temperature.
MITSUBISHI
Confidential (6/25) AA150XS01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
V
www.panelook.com
5. INTERFACE PIN CONNECTION
(1) CN 1(Inte rface Signal)
Used Connector: DF14H-20P-1.25H(56) (HIROSE)
Corresponding connector: DF14-20S-1.25C (HIROSE)
Pin
No.
Symbol
Function(ISP 6 bit com patibility mode )
6 bit input 8 bit input
1 VCC +3.3 V Power supply m
2 VCC +3.3 V Power supply m
3 GND GND m
4 GND GND m
5 Link 0 R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2 R0, R1, R2, R3, R4, R5, G0
6 Link 0+ R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2 R0, R1, R2, R3, R4, R5, G0
7 GND GND m
8 Link 1 G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3 G1, G2, G3, G4, G5, B0, B1
9 Link 1+ G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3 G1, G2, G3, G4, G5, B0, B1
10 GND GND m
11 Link 2 B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA B2, B3, B4, B5, DENA
12 Link 2+ B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA B2, B3, B4, B5, DENA
13 GND GND m
14 CLKIN Clock m
15 CLKIN+ Clock + m
16 GND GND m
17 Link3 See: *2) R0, R1, G0, G1, B0, B1 R6, R7, G6, G7, B6, B7
18 Link3+ See: *2) R0, R1, G0, G1, B0, B1 R6, R7, G6, G7, B6, B7
19 MODE Low=ISP 6 bit compatibility mode
20 SC Scan direction cont rol ( Low = Norm al , High = Revers e ) m
*1) Metal frame is connected to signal GND.
*2) Recommended wiring of Pin 17,18 (6 bit input)
Function(ISP 8 bit
compatibilit y m o de)
High=ISP
8 bit compatibility mode
LVD S
transmitter
LOW data
Pin 17
Pin 18
or
680
620
CC
Ω
Pin 17
Pin 18
Ω
MITSUBISHI
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Confidential (7/25) AA150XS01_02_00
www.panelook.com
Global LCD Panel Exchange Center
(2) CN 2(Backlight )
Backlight-side connector: SM10 B-SHLS-TF(LF)(SN) (JST)
Corresponding connector: SHLP-10V-S-B (JST)
Pin No. Symbol Function
1 NC This pin should be open.
2 NC This pin should be open.
3 LED C 1 LED cathode 1
4 LED A 1 LED anode 1
5 LED A 2 LED anode 2
6 LED C 2 LED cathode 2
7 LED C 3 LED cathode 3
8 LED A 3 LED anode 3
9 LED A 4 LED anode 4
10 LED C 4 LED cathode 4
www.panelook.com
MITSUBISHI
Confidential (8/25) AA150XS01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...