Mitsubishi AA121XF01 Specification
Global LCD Panel Exchange Center
www.panelook.com
TENTATIVE
All information in this technical data sheet is tentative
and subject to change without notice.
12.1” XGA
TECHNICAL SPECIFICATION
AA121XF01
MITSUBISHI ELECTRIC Corp.
Date: Feb.12,’09
ITSUBISHI Confidential (1/24)
M
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
AA121XF01_02_00
www.panelook.com
Global LCD Panel Exchange Center
CONTENTS
www.panelook.com
C
No.
-- COVER
-- CONTENTS
1 APPLICATION
2 OVERVIEW
3 ABSOLUTE MAXIMUM RATINGS 5
4
ELECTRICAL CHARACTERISTICS 5, 6
5
INTERFACE PIN CONNECTION 7, 8
6
INTERFACE TIMING 9, 10, 11, 12, 13
7 BLOCK
MECHANICAL SPECIFICATION 15, 16
8
OPTICAL CHARACTERISTICS 17, 18, 19
9
DIAGRAM 14
Item Page
1
2
3
4
RELIABILITY TEST CONDITION 20
10
11 OTHER
12 HANDLING PRECAUTIONS FOR TFT-LCD MODULE 22, 23, 24
FEATURE 21
ITSUBISHI Confidential (2/24)
M
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
AA121XF01_02_00
www.panelook.com
Global LCD Panel Exchange Center
1. APPLICATION
This specification applies to
www.panelook.com
color TFT-LCD module, AA121XF01.
These sp
(“MITSUBISHI) and include materials protected under copyright of MITSUBISHI. No part of this
document may be reproduced in any form or by any means without the express written permission
of MITSUBISHI.
MITSUBISHI does not assume any liability for infringement of patents, copyrights or other
intellectual property rights of third parties by or arising from use of a product specified in this
document. No license, express, implied or otherwise, is granted under any patents, copyrights or
other intellectual property rights of MITSUBISHI or of others.
MITSUBISHI classifies the usage of the TFT-LCD module as follows. Please confirm the usage
before using the product.
(1) Standard Usage
(2) Special Usage
(3) Specific Usage
ecification papers are the proprietary product of Mitsubishi Electric Corporation
C
omputers, office equipment, factory automation equipment, test and measurement
equipment, communications, transportation equipment(automobiles, ships, trains, etc.),
provided, however, that operation is not influenced by TFT-LCD directly.
Medical equipment, safety equipment, transportation equipment, provided, however, that
TFT-LCD is necessary to its operation.
Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control
systems, life support systems and any other equipment. MITSUBISHI should make a
contract that stipulate apportionment of responsibilities between MITSUBISHI and our
customer.
The product specified in this document is designed for “Standard Usage” unless otherwise specified
in this document. If customers intend to use the product for applications other than those specified
for “Standard Usage”, they should first contact MITSUBISHI sales representative for it's intended
use in writing.
MITSUBISHI has been making continuous effort to improve the reliability of its products.
Customers should implement sufficient reliability design of their application equipments such as
redundant system design, fail-safe functions, anti-failure features.
MITSUBISHI assumes no responsibility for any damage resulting from the use of the product that
does not comply with the instructions and the precautions specified in this document.
Please contact and consult a MITSUBISHI sales representative for any questions regarding this
product.
ITSUBISHI Confidential (3/24)
M
AA121XF01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
2. OVERVIEW
AA121XF01 is 12.1” color TFT-LCD (Thin Film Tr
comp
osed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 6 bit or 8 bit digital data, 1024u 768, 262k-color or 16.7M-color images are displayed
on the 12.1” diagonal screen. Input power voltage is single 3.3 V for LCD driving.
The type of data and control signals are digital and transmitted via LVDS interface per Typ. 65
MHz clock cycle.
Driver circuit for LED backlight is not included in this module. General specifications are
summarized in the following table:
ITEM SPECIFICATION
Display Area (mm)
Number of Dots
www.panelook.com
ansistor Liquid Crystal Display) module
245.76(H) u 184.32(V)
(12.1-inch diagonal)
1024 u3 (H) u 768 (V)
Pixel Pitch (mm)
Color Pixel Arrangement RGB vertical stripe
Display Mode Normally white TN
Number of Color 262k(6 bit/color), 16.7M(8 bit/color)
2
Luminance
Wide Viewing Angle Technology Optical Compensation Film
Viewing Angle (CR t10) 80~80° (H) 80~60° (V)
Surface Treatment Anti-glare and hard-coating 3H
Electrical Interface LVDS (6 bit/8 bit)
Optimum Viewing Angle (Contrast ratio) 6 o’clock
Module Size (mm)
Module Mass (g) 750
Backlight Unit LED, edge-light, replaceable
Characteristic value without any note is typical value.
(cd/m
) 400
0.240 (H) u 0.240 (V)
280.0 (W) u 210.0 (H) u 12.0 (D)
MITSUBISHI Confidential (4/24)
AA121XF01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3. ABSOLUTE MAXIMUM RATINGS
ITEM SYMBOL
Power Supply Voltage for LCD VCC 0 4.0 V
www.panelook.com
MIN. MAX. UNIT
Logic Input Voltage VI
0.3
VCC+0.3 V
Backlight (LED) Current IF 0 180 mA
Op
eration Temperature (Panel)
eration Temperature (Ambient)
Op
No
Storage
Temperature
te 2)
T
Note 1,2)
No
te 2)
T
T
op(Panel)
op(Ambient)
st
30
30
g
30
80 °C
80 °
80 °C
C
[Note]
1) Measured at the center of active area and at the center of panel back surface
2) Top,Tstgd 40qC : 90%RH max. without condensation
Top,Tstg > 40qC : Absolute humidity shall be less than the value of 90%RH at 40qC without
ensation.
cond
4. ELECTRICAL CHARACTERISTICS
(1) TFT-LCD Ambient temperature: Ta = 25
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Power Supply Voltages for LCD VCC 3.0 3.3 3.6 V *1)
Power Supply Currents for LCD ICC -- 320 600 mA *2)
Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC=+3.3V
℃
Logic Input Voltage
High VIH 2.4 -- VCC V MODE, SC
Low VIL 0 -- 0.8 V MODE, SC
*1) Power and signals sequence:
10ms
d
t1
d 50ms
d 50ms
t1
L
CD Power Supply
c Signal
Logi
cklight Power Supply
Ba
0 < t2
0 < t3
0.9VCC
0.1VCC
t2
VCC
data
200ms
200ms
0 d t6
t3
t4
d
d t5
0.9VCC
0.1VCC
t4
0.1VCC
t5 t6
d
ata: RGB DATA, DCLK, DENA, MODE, SC
ITSUBISHI Confidential (5/24)
M
AA121XF01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
VCC-dip conditions:
www.panelook.com
1) When 2.6 V
2) Whe
n VCC < 2.6 V
VCC < 3.0 V, td d 10 ms
d
VCC-dip conditions should also follow the power and signals sequence.
VC
C
V
V
2.6
3.0
td
*
2) VCC = +3.3 V , f
= 48.4 kHz, fV= 60 Hz, f
H
= 65 MHz
CLK
Display image at typical power supply current value is 256-gray-bar pattern (8 bit), 768 line mode.
*3) Fuse
Parameter
Fuse Type Name Supplier Remark
VCC
) The power supply capacity should be designed to be more than the fusing current.
*
FCC16162AB Kamaya Electric Co., Ltd. *)
(2) Backlight
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
IF = 120 mA, Ta = 25
IF = 120 mA, Ta = 0
IF = 120 mA, Ta = 30
LED
Voltage VF
-- (24)
-- --
30.4 V
32 V
-- -- 33.2 V
LED Current IF -- 120 150 mA *1), *3)
LED Life Time LT 60,000 -- -- h
IF = 120 mA, Ta = 25
*4), *5), Continuous operation
[Note]
*1) Constant Current Drive
*2) The Voltage deviation between strings: |V
*3) LE
D Current measurement method
LCD
dule
Mo
㩷
A1
C1
A2
C2
– Vf2| d 2V
f1
A
A
Power
Supply
Power
Supply
℃
℃
℃
℃
*4) LED life time is defined as the time when the brightness becomes 50% of the initial value.
*5) The life time of the
backlight depends on the ambient temperature. The life time will decrease
under high temperature.
ITSUBISHI Confidential (6/24)
M
AA121XF01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
5. INTERFACE PIN CONNECTION
(1)CN 1(INTERFACE SIGNAL)
Used connector: FI-SE20P-HFE (JAE)
Corresponding connector: FI-S20S[for discrete wire] , FI-SE20ME[for FPC] (JAE)
Pin
No.
Symbol
1 VCC
2 VCC
3 GND
4 GND
5
Link 0
Link 0+ R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2 R0, R1, R2, R3, R4, R5, G0
6
R0, R1, R2, R3, R4, R5, G0 R2, R3, R4, R5, R6, R7, G2
7 GND
8
Link 1
9
Link 1+ G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3 G1, G2, G3, G4, G5, B0, B1
G1, G2, G3, G4, G5, B0, B1 G3, G4, G5, G6, G7, B2, B3
10 GND
11
Link 2
B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA
12 Link 2+ B2, B3, B4, B5, DENA B4, B5, B6, B7, DENA B2, B3, B4, B5, DENA
13 GND
14
CLKIN Clo
15 CLKIN+
16 GND
17
Link3
See: *2) R0, R1, G0, G1, B0, B1
18 Link3+ See: *2) R0, R1, G0, G1, B0, B1 R6, R7, G6, G7, B6, B7
19
MODE Low=ISP 6 bit compatibility mode
20 SC
Scan direction control. ( Low : Normal , High : Reverse )
*1) Metal frame is connected to signal GND.
*2) Recommended wiring of Pin 17,18 (6 bit input)
Function (ISP 6 bit compatibility mode)
6 bit input
+3.3 V Power supply
+3.3 V Power supply
www.panelook.com
Function (ISP 8 bit
8 bit input
GND
GND
GND
GND
GND
ck m
ck +
Clo
GND
compatibility mode)
m
m
m
m
R0, R1, R2, R3, R4, R5, G0
m
G1, G2, G3, G4, G5, B0, B1
m
B2, B3, B4, B5, DENA
m
m
m
R6, R7, G6, G7, B6, B7
High=ISP
8 bit compatibility mode
m
LV
DS
transmitter
(2)CN 2(BACKLIGHT)
Backlight-sid
Corresponding connector: SHLP-06V-S-B (JST)
Pin No.
LO
W data
Pi
Pi
n 17
n 18
or
e connector: SM06B-SHLS-TF (JST)
Symbol Function
1
2
3
4
5
6
NC This pin should be open.
NC This pin should be open.
LED C 1 LED cathode 1
LED A 1 LED anode 1
LED A 2 LED anode 2
LED C 2 LED cathode 2
680
620
VCC
Ω
Pin 17
Pin 18
Ω
ITSUBISHI Confidential (7/24)
M
AA121XF01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
(3) ISP data mapping
a. ISP 6 bit compatibility mode(6 bit input)
CLKIN+/-
www.panelook.com
1C
LK
Link0+/-
Link1+/-
nk2+/ -
Li
b. ISP 6 bit compatibility mode(8 bit input)
CL
KIN+/-
Li
nk0+/-
Li
nk1+/-
nk2+/-
Li
NA
NA
R1G0 R5 R4 R3 R2 R0
G2B1 B0 G5 G4 G3 G1
B5 B4 B2
B7 B6 B4
B3DE
LK
1C
R3G2 R7 R6 R5 R4 R2
G4B3 B2 G7 G6 G5 G3
B5DE
nk3+/-
Li
c
. ISP 8 bit compatibility mode
CL
KIN+/ -
Li
nk0+/ -
Link1+/-
nk2+/ -
Li
nk3+/ -
Li
R1B1 B0 G1 G0 R0
LK
1C
R1G0 R5 R4 R3 R2 R0
G2B1 B0 G5 G4 G3 G1
B3DENA B5 B4 B2
R7B7 B6 G7 G6 R6
ITSUBISHI Confidential
M
(8/
24)
AA121XF01_02_00
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...