MITEL MH88500IN Datasheet
MH88500IN
Hybrid Subscriber Line Interface Circuit (SLIC)
Preliminary Inf ormat ion
Features
• Differential to s ingle en ded conv ersion
• No transforme rs req uired
• Minim um in sta lla tio n s pa ce
• Off-Hook detection and LED indicator drive
• Relay drive outp ut
• Battery and ri ngin g feed to line
• Logic interface: MUTE
, OFHK, RC
• Mute of inco ming aud io
• Dial pulse detection
• Voltage surge protecti on
Applications
Line Interfac e for:
• PABX
• Intercoms
• Key System s
ISSUE 1 April 1995
Ordering Information
MH88500 IN 20 Pin SIL Packa ge
0°C to 70°C
Descript io n
The Mitel MH88500IN Subscriber Line Interface
Circuit provides a complete interface between the
telephone line and a speech switch requiring only
single bidirectional switch per crosspoint. The
functions provided by the MH88500IN include
bidirectional differential to single ended conversion
in the speech path, line battery feed, ringing feed
and loop and dial pulse detection. The device is
fabricated as a thick film hybrid in a 20-pin ‘single-inline’ package allowing optimum circuit board packing
density.
TIP
RING
RING
FEED
CD
RD
RC
RGND
VA
Loop Feed/
Ring Feed
Relay Drive
Circuit
V
1
A2
Figure 1 - Functional Blo ck Diag ram
V
Speech Circuit
V
B
C1
V
A2
Loop Detectio n
V
C2
GND
JUNCTOR
V
B
MUTE
OFHK
LED
THRESH ADJ
2-43
MH88500IN Preliminary Infor mation
TIP
VA1
RING
RING FEED
THRESH ADJ
JUNCTOR
IC
VC1
GND
V
LED
OFHK
VA2
GND
VC2
MUTE
RD
RGND
RC
CD
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Figure 2 - Pin Connections
Pin Description
Pin # Name Description
1TIPTip Lead. Connects to the “Tip” lead (A-wire) of the telephone line.
2V
A1
Positive Li ne Fe ed S upp ly Voltag e. Normally connected to VA2.
3RINGRing Lead. Connects to the “Ring” lead (B-wire) of the telephone lin e.
4 RING FEED Negative Li ne Feed Voltage and Ringing Input. Normall y connected to Ring Relay.
5ICInternal Connection. Leave open circuit. Use for testing only.
6V
C1
Sense Inpu t. Normally connected to negative line fe ed voltag e supply.
7GNDAnalog ground (0V). Internally co nnecte d to pin 13.
8V
B
9LED
10 OFHK
11 THRESH ADJ All ows a djustm ent of OFHK
12 V
A2
Negative Anal og Suppl y Voltage.
LED Dr ive Output. Drives an LED directly. Off-Hook condition, logic low.
Logic Low Output. Indicates closed loop condition (Off-Hook and dial pulsing).
detection threshold.
Positive P owe r Suppl y Voltage. Normally connected to VA1.
13 GND Analog Ground (0V). Internally connected to pin 7.
14 V
C2
15 MUTE
Loop Detector Voltage Supply.Connected to negative line feed voltages supply.
Input mutes the incom in g audio. Active lo w.
16 JUNCTOR Receive/tr ansm i t audio sp eech pa th. (referenced to 0V GND)
17 RD
Relay Drive Output. Open collector sinks current when RC high. Diode clamp
protecte d.
18 RGND Ground for Relay Drive Circui t .
19 RC Ring Control Input. Active high.
20 CD Clampin g Dio de. Normally connected to re lay positive voltage.
2-44
Preliminary Information MH88500IN
Functional Description
Line Feed/Ring Feed Circuit
Speech Circuit
The line feed circuit provides loop current and the
The speech circuit converts the bidirectional TIP and
RING line pair to a bidirectional single ended junctor
line. Figure 3 illustrates a typical connection between
two SLIC’s through two crosspoint switches. This
configuration gives optimum transhybrid loss as
seen from Figure 4 given that the output impedance
of the Junctor line is 604Ω.
ability to apply ringing onto TIP and RING. The
impedance from RING FEED to GND is 600Ω which
gives the loop current as:
IL = Voltage at RING FEE D pin
Amps
Telephone Imp eda nce + 60 0
The MUTE
input mutes signals coming from TIP and
RING to the junctor line while allowing the signal
from the jun c to r to the tip-rin g p air to b e tr an s m itte d .
Loop Detection
The loop detection circuit determines whether a low
enough impedances is across TIP and RING to be
recognized as an off-hook condition.
(Threshold impedance = 5.4kΩ with no adjustment)
This threshold level can be adjusted by the use of
external res istors as show n in Figure 6 . OFHK
low output drive capability so it may drive CMOS
operating with differe nt power supp lies.
TIP
RING
1
3
has
MH88500IN
TIP
RING
The positive supply for the line feed circuit is V
through the loop current is determined from RING
FEED and GND.
Relay Drive Circuit
The relay drive circuit switches ringing onto RING
FEED (Fig.7). The diode is present to suppress
voltage transients during relay switches caused by
the inductive coils of the relay. Ringing voltage
includes AC ringing (90V typically) an dDC line feed
voltage (-24V typically).
75Ω
16
JUNC
CROSSPOINT
SWITCH
A1
TIP
RING
MH88500IN
1
TIP
3
RING
JUNC
16
75Ω
CROSSPOINT
SWITC H
Figure 3 - SLIC Crosspoi nt S witc h Connecti on
2-45
Loading...