Mindray BIO Medical electronics RF013B MR 001 User Manual

Remote Control
Instructions For Use
Product Information
Intended Use
The remote keypad is intended to be used with Mindray’s BeneView T series and BeneVision N series patient monitors. The user shall be responsible for ensuring the compatibility between the remote keypad and the monitoring devices by either referring to this instructions for use or contacting us before use. The remote keypad must be used by trained clinical personnel.
Precautions
Check the remote keypad and accessories before use. Do not use
z
the remote keypad in case of damage, block, deterioration or visible contamination.
Disposal of the remote keypad and accessories shall comply with applicable
z
regulations. Do not dispose randomly.
Warnings
The remote keypad must be used by trained clinical personnel.
z
The remote keypad is for indoor use only.
z
Do not expose to moisture, liquid, or heat environment.
z
Keep the keypad with special care after use to avoid unintended
z
operation.
Overview of The Remote Keypad
1
4 6
7
8
10
12
No. Key Name Description
1 Alarm Reset Key
2 Alarm Pause Key
3 Up Arrow Key Moves the highlight bar up. 4 Right Arrow Key
(only for BeneVision N series patient monitors)
5 Right Arrow Key
(only for BeneVision N series patient monitors)
www.mindray.com Mindray Building, Keji 12th Road South, Hi-tech Industrial Park,
Nanshan, Shenzhen 518057 P.R. China
Tel:+86 755 81888998
Fax:+86 755 265826 80
Acknowledges the ongoing alarm. For details, see "Alarms" in BeneView T series or BeneVision N series patient monitor operator's manual.
Pauses the current alarm. For details, see “Alarms” in BeneView T series or BeneVision N series patient monitor operator’s manual.
Switches the screen.
Switches the screen.
E-mail: service@mindray.com
2
3
5
9
11
13
RF013B-MR-001
No. Key Name Description
6 Enter Key Enters a menu or confirms a selection. 7 Down Arrow Key Moves the highlight bar down. 8 Standby Key Enters the standby mode. 9 Start/Stop NIBP Key Starts an NIBP measurement or stops the
10 Zero IBP Key Displays the Zero IBP menu. 11 Manual Event Key Manually Triggers a event. 12 Multifunction Mouse Key
13 Main Screen/Main Menu Key Backs to the main screen or main menu.
Preparing the Patient Monitor (for BeneView T series patient monitors)
The patient monitor shall be properly configured for the use of the remote keypad. Ask the authorized service personnel to perform the configuration.
Note
This operation needs password and is for authorized service personnel
z
only. Do not configure it yourself. If the corresponding configuration item could not be found in the
z
configuration menu, ask the authorized service personnel to upgrade the system software to the latest version first.
Preparing the Remote Keypad
Preparing the receiver
1. Open the battery compartment, and take the receiver out.
2. Plug the receiver to the USB connector on the rear panel of the patient monitor.
Note
Do not plug the receiver to the USB connector on the BeneView T series
z
patient monitor used for connecting iView system or external display, or to the USB connector on the BeneVision N series patient monitor used for connecting iView system.
Installing battery
Warnings !
Keep batteries away from heat, sunshine, or fire. Never discard batteries in
z
fire. When the remote keypad is not used for long periods, remove the
z
battery. Make sure that the patient monitor has been properly configured.
z
The remote keypad is effective once the battery is installed. Keep the
z
remote keypad with special care every time you finish your operation to avoid any unintended operation.
1. Insert an AAA battery with correct polarity (+/-).
2. Close the battery compartment.
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CE Statement
Manufacturer: Fenito Electronic Technology (Shenzhen) Co., Ltd, Hereby ,
Fenito Electronic Technology (Shenzhen) Co., Ltd
RF013B-MR-001 is in compliance with the essential requirements provisions of Directive 1999/5/EC. Dispose of used batteries according to the instructions.
Use the Remote Control in the environment with the temperature between 0 and 50 .
current NIBP measuremet.
When the mouse is inactivated, use this
z
key to activate the mouse. When the mouse is activated, use this
z
key to locate the cursor. If you carry out no operations within one minute after activating the mouse, the mouse will be inactivated.
hereby declares that this Remote Control
Risk of explosion if battery is replaced by an incorrect type.
and other relevant
Loading...