Milwaukee L4C, L4B2 Instructions Manual
WARNING
4. USE ONLY WITH CERTIFIED POWER SUPPLY. Others may result in
SPECIFICATIONS
SYMBOLOGY
Direct Current
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal injury.
1. THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING
SAVE THESE INSTRUCTIONS
INSTRUCTIONS FOR THE REDLITHIUM
®
USB CHARGER CAT. NO.
L4C AND BATTERY CAT. NO. L4B2..
2. CHARGE ONLY REDLITHIUM
®
USB BATTERIES IN THE
REDLITHIUM
®
USB CHARGER. OTHER TYPES OF BATTERIES
MAY CAUSE PERSONAL INJURY AND DAMAGE.
3. BEFORE USING THE BATTERY AND CHARGER, READ THIS
OPERATOR’S MANUAL, YOUR TOOL OPERATOR’S MANUAL,
AND ALL LABELS ON THE BATTERY, CHARGER AND TOOL.
a risk of fire, electric shock or personal injury.
5. AVOID DANGEROUS ENVIRONMENTS. Do not charge battery in rain,
snow, damp or wet locations. Do not use battery or charger in the
presence of explosive atmospheres (gaseous fumes, dust or
flammable materials) because sparks may be generated when
inserting or removing battery, possibly causing fire.
6. CHARGE IN A WELL VENTILATED AREA. Do not block charger vents.
Keep them clear to allow proper ventilation. Do not allow smoking or
open flames near a charging battery. Vented gases may explode.
7. MAINTAIN CORD. When unplugging charger, pull plug rather than cord
to reduce the risk of damage to the electrical plug and cord. Never carry
charger by its cord.
Keep cord from heat, oil and sharp edges. Make
sure cord will not be stepped on, tripped over or subjected to damage or
stress. Do not use charger with damaged cord or plug. Have a damaged
charger replaced immediately.
8. USE ONLY RECOMMENDED ATTACHMENTS. Use of an attachment
not recommended or sold by the battery charger or battery manufacturer
may result in a risk of fire, electric shock or personal injury.
9. TO REDUCE THE RISK OF ELECTRIC SHOCK, always unplug
charger before cleaning or maintenance.
10. DO NOT BURN OR INCINERATE BATTERY PACKS. Battery may
explode, causing personal injury or damage. Toxic fumes and materials
are created when battery are burned.
11. DO NOT CRUSH, DROP, OR DAMAGE battery. Do not use a battery
or charger that has received a sharp blow, been dropped, run over, or
damaged in any way (e.g., pierced with a nail, hit with a hammer,
stepped on).
12. DO NOT DISASSEMBLE. Incorrect reassembly may result in the risk
of electric shock, fire or exposure to battery chemicals. If it is damaged,
take it to a MILWAUKEE
®
service facility.
13. BATTER
Y CHEMICALS CAUSE SERIOUS BURNS. Never allow
contact with skin, eyes, or mouth. If a damaged battery leaks battery
chemicals, use rubber or neoprene gloves to dispose of it. If skin is
exposed to battery fluids, wash with soap and water and rinse with
vinegar. If eyes are exposed to battery chemicals, immediately flush with
water for 20 minutes and seek medical attention. Remove and dispose
of contaminated clothing.
14. DO NOT SHORT CIRCUIT. A battery will short circuit if a metal object
makes a connection between the positive and negative contacts on the
battery pack. Do not place a battery pack near anything that may cause
a short circuit, such as coins, keys or nails in your pocket. A short
circuited battery may cause fire and personal injury.
15. STORE YOUR BATTERY AND CHARGER in a cool, dry place. Do
not store battery where temperatures may exceed 50°C (120°F) such as
in direct sunlight, a vehicle or metal building during the summer.
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool,
READ AND SAVE ALL INSTRUCTIONS FOR FUTURE REFERENCE.
ADDITIONAL BATTERY SAFETY RULES
WARNING
battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or
conductive fluids, such as seawater, certain industrial chemicals, and bleach or
bleach-containing products, etc., can cause a short circuit.
Charger Cat. No. ..........................................................................................L4C
Input Volts................................................................................................... 5 DC
Input Watts....................................................................................................10W
Output Volts................................................................................................ 4 DC
Output Amps................................................................................................ 2.1A
Battery Cat. No...........................................................................................L4B2
Volts............................................................................................................ 4 DC
Operating Temperature
Battery and Charger...............................................4°C to 40°C (40°F to 104°F)
Battery and Tool....................................................-18°C to 65°C (0°F to 149°F)
Power Supply Cat. No...............................................................4931 4605 95A
Wall Plug Input Volts.........................................................120 AC to 220-240 AC
Volts
V
Read Operator's Manual
BATTERY
CHARGER
WARNING
Maintenance and Storage
Do not expose your battery or cordless tools to water or rain, or allow them to get
wet. This could damage the tool and battery. Do not use oil or solvents to clean
or lubricate your battery. The plastic casing will become brittle and crack,
causing a risk of injury.
Store batteries at room temperature away from moisture. Do not store in damp
locations where corrosion of terminals may occur. As with other battery types,
permanent capacity loss can result if the pack is stored for long periods of time
at high temperatures (over 49°C(120°F)). MILWAUKEE
®
Li-Ion batteries
maintain their charge during storage longer than other battery types. After about
a year of storage, charge the battery as normal.
To reduce the risk of injury o
r explosion, never burn or
incinerate a battery pack even if it is damaged, dead or
completely discharged. When burned, toxic fumes and materials are
created.
Disposing of MILWAUKEE
®
Li-Ion Battery
MILWAUKEE
®
Li-Ion batteries are more environmentally friendly than some
other types of power tool batteries. Always dispose of your battery according to
federal, state and local regulations. Contact a recycling
agency in your area for recycling locations.
Even discharged batteries contain some energy. Before disposing, use electrical
tape to cover the terminals to prevent the battery from shorting, which could
cause a fire or explosion.
WARNING
REDLITHIUM® USB BATTERY AND
CHARGER
How to Charge the Battery Pack
6. The indicator light will display the charging status:
Red Flashing: Charging, 0-25% charged
Orange Flashing: Charging, 25-80% charged
Green Flashing: Charging, 80-99% charged
Green Solid: 99-100% Charged
Red/Green Flashing: Damaged or Faulty Battery
Amps
A
Regulatory Compliance mark
(RCM). This product meets
applicable regulatory
requirements.
Additional Safety Rules
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
This charger was only
suitable for indoor use.
Never expose the
charger to rain.
Class III appliance
T3.0A
Time-lag fuse 3.0A
Charge only REDLITHIUM
®
USB batteries
in the REDLITHIUM
®
USB charger. Other
types of batteries may cause personal injury and damage.
1. Plug your USB cable into a power source such as an AC wall
adaptor, computer or car port.
2. Insert the micro USB into the micro USB port.
3. Twist the charger cap and pull out the charger bay.
4. Align the battery arrow with the charger arrow and insert the
battery completely.
5. Close the battery bay and twist the cap to lock.
If the light indicator flashes red and green, check that the
battery is fully seated into the bay. Remove the battery and
reinsert. If the light continues to flash red and green, the
battery may be extremely hot or cold, or wet. Allow the
battery to cool down, warm up, or dry out and then reinsert.
If the problem persists, contact a MILWAUKEE
®
service
facility.
Fuel Gauge
When the charger is unplugged and a battery is inserted, the
indicator light will display the current battery charge:
Red Flashing: 0-10% remaining
Red Solid: 10-25% remaining
Orange Solid: 25-80% remaining
Green Solid: 80-100% remaining
WARNING
To reduce the risk of injury, always unplug
the charger and remove the battery from
the charger before performing any maintenance. The charger
and battery have no internal serviceable parts. Never
disassemble the battery or charger.
Maintenance and Storage
Store your charger in a cool, dry place. As a general practice, it is
best to unplug battery chargers and remove batteries when not in
use. No battery damage will occur, however, if the charger and
battery are left plugged in.
WARNING
To reduce the risk of injury and damage,
never immerse your battery or charger in
liquid or allow a liquid to flow inside them.
Cleaning
Clean out dust and debris from charger vents and electrical
contacts by blowing with compressed air. Use only mild soap and a
damp cloth to clean the battery and charger, keeping away from all
electrical contacts. Certain cleaning agents and solvents are
harmful to plastics and other insulated parts. Some of these include
gasoline, turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household detergents containing
ammonia. Never use flammable or combustible solvents around
batteries, charger, or tools.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
21 Kelletts Road, Rowville, VIC 3178
Melbourne, Australia
Milwaukee Tool (New Zealand)
2 Landing Drive, Mangere
Auckland, 2022, New Zealand
Designed by Milwaukee Electric Tool Corp.
Professionally Made in China for Milwaukee Tool (Australia) / Milwaukee Tool (New Zealand)
Printed in China
WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with tool. This
warranty applies only to product sold in Australia and New Zealand.
MILWAUKEE
®
prides itself in producing a premium quality product that is
Nothing But Heavy Duty®. Your satisfaction with our products is very important to
us! If you encounter any problems with the operation of this tool, please contact
your authorised MILWAUKEE® dealer.
For a list of MILWAUKEE® dealers, guarantee or service agents please contact
MILWAUKEE® Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 279 624)
or visit www.milwaukeetools.com.au / www.milwaukeetools.co.nz.
961001496-01(A)
Loading...