Cat. No.
0&$*;3'%
OPERATOR'S MANUAL
M18 FUEL™ 5" RAPID STOP GRINDER
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure
to follow the warnings and instructions may result in electric shock, re and/or serious
injury. Save all warnings and instructions for future reference. The term "power
tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
•
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmos
pheres, such as in the presence of ammable
liquids, gases or
which may ignite the dust or fumes.
Keep children and bystanders away while oper
•
ating a power tool. Distractions can cause you to
lose control.
Power tools create
dust.
sparks
ELECTRICAL SAFETY
WORK AREA SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi
tions. W
ater entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
•
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter
rupter (GFCI) protected supply. Use of an GFCI
reduces the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your nger on the switch or energising power tools
that have the switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
•
Dress properly. Do not wear loose clothing or
-
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
• If devices are provided for the connection of
-
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
• Disconnect the plug from the power source and/
-
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
• Store idle power tools out of the reach of chil
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.
hands of untrained users.
Maintain power tools. Check for misalignment or
•
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak
ing into account the working conditions and the
work
to
operations differ
in a hazardous situation.
Power tools are dangerous in the
be
performed. Use of
ent from those intended could result
the
power tool for
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically desig
nated battery packs. Use of any other battery
packs may create a risk of injury and re.
•
When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
2
-
-
-
to another. Shorting the battery terminals together
may cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
-
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES
• This power tool is intended to function as a
grinder, sander, wire brushing or cut-off tool.
Read all safety warnings, instructions, illus
trations and specications provided with this
power tool.
below may result in electric shock, re and/or seri
ous injury.
•
Operations such as polishing are not recom
mended to be performed with this power tool. Operations for which the power tool was not designed
may create a hazard and cause personal injury
Do not use accessories which are not speci
•
cally designed and recommended by the tool
manufacturer
be attached to your power tool, it does not assure
safe operation.
The rated speed of the accessory must be at
•
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and y apart.
• The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
• Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by anges, the arbour hole of the ac
cessory must t the locating diameter of the
ange. Accessories
ing hardware of the power tool will run out of bal
ance, vibrate excessively and may cause loss of
control.
• Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or acces
sory is dropped, inspect for damage or install
an
undamaged
installing
bystanders away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. Damaged acces
sories will normally break apart during this test time.
• Wear personal protective equipment. Depend
ing on application, use face shield, safety
goggles or safety glasses. As appropriate,
wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye pro
tection must be capable of stopping ying debris
generated by various operations.
Failure to follow all instructions listed
. Just because the accessory can
do
that
accessory. After
accessory, position yourself and
an
match
not
inspecting
The dust mask
the
mount
and
-
-
-
.
-
-
-
-
-
-
-
-
or respirator must be capable of ltrating particles
generated by your operation. Prolonged exposure
to high intensity noise may cause hearing loss.
• Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Frag
ments of workpiece or of a broken accessory may
y away and cause injury beyond immediate area
of operation.
• Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact hid
den wiring. Contact with a “live” wire will also
make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
• Never lay the power tool down until the acces
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the pow
er tool out of your control.
• Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the ac
cessory into your body.
• Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
• Do not operate the power tool near ammable
materials. Sparks could ignite these materials.
• Do not use accessories that require liquid cool
ants. Using water or other liquid coolants may result in electrocution or shock.
Kickback and Related W
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory
rapid
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward or
away from the operator, depending on direction of
the wheel’s movement at the point of pinching. Abra
sive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
• Maintain a rm grip on the power tool and posi
tion your body and arm to allow you to resist
kickback forces. Always use auxiliary handle,
if provided, for maximum control over kickback
or torque reaction during start-up. The operator
can control torque reactions or kickback forces, if
proper precautions are taken.
• Never place your hand near the rotating acces
sory. Accessory may kickback over your hand.
•
Do not position your body in the area where
power tool will move if kickback occurs. Kick
back will propel the tool in direction opposite to the
wheel’
Use special care when working corners, sharp
•
edges etc. Avoid bouncing and snagging the
3
of
stalling
the
s movement at the point of snagging.
arnings
. Pinching or snagging causes
rotating
accessory
which in turn
-
-
-
-
-
-
-
-
-
-
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
• Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create fre
quent kickback and loss of control.
Safety Warnings
sive Cutting-Off Operations:
•
Use only wheel types that are recommended
for your power tool and the specic guard de
signed for the selected wheel. Wheels for which
the power tool was not designed cannot be adequately guarded and are unsafe.
•
The grinding surface of centre depressed
wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel that
projects through the plane of the guard lip cannot
be adequately protected.
• The guard must be securely attached to the
power tool and positioned for maximum safety,
so the least amount of wheel is exposed to
wards the operator. The
operator
dental contact with wheel.
Wheels must be used only for recommended
•
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces ap
plied to these wheels may cause them to shatter.
Always use undamaged wheel anges that are
•
of correct size and shape for your selected
wheel. Proper wheel anges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel anges.
• Do not use worn down wheels from larger pow
er tools. Wheel intended for larger power tool is
not suitable for the higher speed of a smaller tool
and may burst.
Additional Safety Warnings Specic for Abra
sive Cutting-Off Operations:
• Do not “jam” the cut-off wheel or apply exces-
sive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel
increases
or binding of the wheel in the cut and the possibility
of kickback or wheel breakage.
•
Do not position your body in line with and be
hind the rotating wheel. When
point of operation, is moving away from your body
the possible
wheel and the power tool directly at you.
When wheel is binding or when interrupting a
•
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may
occur. Investigate and take corrective action to
eliminate the cause of wheel binding.
• Do not restart the cutting operation in the work
piece. Let the wheel reach full speed and care-
fully reenter the cut. The wheel may bind, walk
up or kickback if the power tool is restarted in the
workpiece.
from
the
Specic
broken
loading
and
kickback
Grinding
for
guard
fragments
wheel
susceptibility
may
propel
helps
the
and
to
and acci
to
wheel,
the
spinning
Abra-
protect
twisting
at
the
•
Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick
back. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of
-
the workpiece on both sides of the wheel.
•
Use extra caution when making a “pocket cut”
into existing walls or other blind areas. The pro
truding wheel may cut gas or water pipes, electrical
wiring or objects that can cause kickback.
-
Safety Warnings Specic for Sanding Operations:
• Do not use excessively oversized sanding disc
paper. Follow manufacturers recommenda
tions, when selecting sanding paper. Larger
sanding paper extending beyond the sanding pad
presents a laceration
ging, tearing of the disc or kickback.
Safety Warnings
erations:
• Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
-
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
• If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work load
and centrifugal forces.
Additional Safety Warnings
Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE® service facility for a
replacement.
• WARNING: Some dust created by power sanding,
-
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause can
cer, birth defects or other reproductive harm.
Some examples of these chemicals are:
-
• lead from lead-based paint
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
-
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe
,
cially designed to lter out microscopic particles.
Specic
hazard
for Wire
and
may
cause
Brushing Op-
SYMBOLOGY
Volts
Direct Current
-
Rated Revolutions per Minute
(RPM)
snag
-
-
-
-
-
-
4
SPECIFICATIONS
Cat. No.
M18 CAG
125XPDB
Volts DC
18
RPM
Spindle
Thread Size
Rated
8500
M14
Max. Wheel
Size
5" (125mm)
FUNCTIONAL DESCRIPTION
2
1
3
4
5
7
1. Spindle lock
2. Dust guard
3. Switch lock-off
6
Paddle switch
4.
5. Side handle
6. Guard
7. Guard lock lever
ASSEMBLY
WARNING Recharge only with the
charger specied for the battery. For specic
charging instructions, read the operator’s
manual supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.
WARNING Always remove battery
pack before changing or removing accessories. Only use accessories specically recommended for this tool. Others may be hazardous.
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side shields.
Installing/Removing/Cleaning the Dust Screen
Using the dust screen will increase the performance
and extend the life of the tool.
1. To attach the dust screen, snap the screen over
the tool’s handle.
2. To remove the dust screen, insert a at screw-
driver into the notch at the top of the dust screen
and pry away from the tool.
3. To clean the dust screen, tap against a hard
surface, or blow clean with compressed air.
Installing Side Handle
The side handle may be installed on either side of
the gear case. Position the side handle in the location which offers best control and guard protection.
To install, thread side handle into side handle socket
and tighten securely.
WARNING To reduce the risk of injury
when grinding:
• ALWAYS use the proper guard.
• ALWAYS properly install the guard.
• ALWAYS hold the tool rmly with both
hands using the handles provided before
and during grinding.
• NEVER use a wheel that has been dropped.
• NEVER bang grinding disc onto work.
• NEVER grind without proper safety
equipment.
Installing, Removing and Adjusting the Guard
This tool is shipped with a guard. The guard must
be used when using the tool as a grinder. The guard
may be removed when using tool as a sander.
1. To remove the guard, remove the battery pack
and remove any accessories from spindle.
2. Press in the lock lever and rotate the guard to
line up the tabs on the grinder with the slots in
the guard.
3. Press in the lock lever and lift the guard straight
up and away from the tool.
Fig. 1
Detent slots
Tab
slots
4. To install the guard, remove the battery pack
and remove any accessories from the spindle.
NOTE: Use only 5" (125 mm) grinding wheels
with 5" (125 mm) guards.
5. Line up the tabs on the grinder with the slots in
the guard.
6. Press in the lock lever and press the guard onto
the tool.
7. To adjust the guard, press in the lock lever and
rotate the guard to one of ve detent slots.
5
WARNING Only use accessories with
Maximum Safe Operating Speed rated at least
equal to the maximum speed marked on the
power tool. This speed is based on the strength
of the wheel, allowing for a reasonable measure of safety. It is not meant to imply a best or
most efcient operating speed. Do not exceed
the Maximum Safe Operating Speed.
Installing/Removing Accessories
Make sure the wheel does not extend beyond the
bottom of the guard. Threaded hub grinding wheels
may require a deeper guard (see "Accessories").
1. Remove the battery pack.
2. Properly position the guard (Fig. 2).
Fig. 2
3. Wipe the ange, FIXTEC nut and spindle to
remove dust and debris. Inspect the parts for
damage. Replace if needed.
4. Place the ange on spindle, as shown (Fig. 3).
Fig. 3
5. Place the selected wheel on the spindle and align
it with the ange.
6. Press in the spindle lock button. With the tightening tab up, thread the FIXTEC nut clockwise
onto the spindle. Use the tightening tab on the
FIXTEC nut to grasp the nut and tighten securely.
Press down the tightening tab.
7. To remove wheel, remove the battery pack and
reverse the procedure.
Operator's Zones
Tightening tab
FIXTEC nut
Wheel
Flange
Spindle
OPERATION
WARNING Always remove battery
pack before changing or removing accessories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Controlled Start
The controlled start feature reduces the torque
reaction "jerk" when its trigger is pulled.
Electric Brake
The electric brake engages when the switch is
released, causing the wheel to stop within seconds.
There may be a delay between the time the switch is
released and when the brake engages. Occasionally
the brake may miss completely. If the brake misses
frequently, have the tool serviced by one of our
authorised MILWAUKEE® service centres. Make
sure the tool comes to a complete stop before laying
it down.
Paddle Switch Operation
To start the tool, grasp the handle and side handle
rmly. Push the lock-off button forward and squeeze
the paddle switch.
To stop the tool, release the paddle switch. Make
sure the tool comes to a complete stop before laying the tool down.
General Operation
1.
If you have just installed an accessory or are
beginning a period of work, test it by letting it
spin for one minute before applying it to the
workpiece. Out-of-balance or damaged accessories can mar workpiece, damage the tool, and
cause stress that may cause accessory failure.
2. Use a clamp, vise or other practical means to
hold your work, freeing both hands to control
the tool.
3. Hold tool securely with both hands.
4. Start the tool.
Note: If the battery is inserted when the tool
switch is in the “ON” position, the tool will not run.
Turn the tool off, then back on to begin work..
5. Allow accessory to come to full speed before
beginning work.
6. Control pressure and surface contact between
accessory and workpiece. Too much pressure
slows speed.
7. When nished, turn off the tool and make sure it
comes to a complete stop before laying it down.
6
USING CUT-OFF WHEELS
WARNING A Type "1" guard must be
installed when using a cut-off wheel to provide
maximum protection for the operator if the
wheel should break.
Type "1" Cut-Off Wheels are suited for small cut-off
and shallow notching operations only.
When using a cut-off wheel, hold the tool as shown,
using only the edge of the wheel.
Fig. 4
Grinding and cut-off wheels should NOT be
dropped, rolled or bumped.
Discard wheels that have been dropped, rolled,
bumped, subjected to extreme changes in temperature, or come into contact with solvents or wetness.
Grinding
When grinding, hold tool at a 5
o
to 15o angle, using
constant pressure for a uniform nish. Too great an
angle causes concentrated pressure on small areas
which may gouge or burn work surface.
Fig. 5
Hold at a
5° to 15°
angle
For best result use only this portion of disc
WARNING Using the face of a Cut-Off
Wheel (as in grinding) will cause the Wheel
to crack and break, resulting in serious personal injury.
USING GRINDING WHEELS
WARNING To reduce the risk of injury,
the operator should be instructed in the use,
care and protection of grinding wheels.
Grinding Wheel Selection
Use grinding wheels, and accessories that are:
• correct size as written on tool’s nameplate.
• rated at or above the RPM listed on the tool’s
nameplate.
• correct accessory, wheel type and grit for the job.
Grinding is the cutting action of thousands of abra-sive
grains on the face of a grinding wheel. When grinding
metals such as steel and iron, choose an aluminum oxide
grinding wheel. Select a silicon carbide grinding wheel for
stone and concrete. Use cotton reinforced wheels for
non-ferrous metals.
Type 27 Reinforced 1/8" (3.18 mm) thick or less Cut-Off
Wheels are suited for small cut-off and shallow notching
operations only. Always handle wheels carefully to avoid
damage. Before installing any wheel, always inspect it for
cracks. If wheel is cracked, discard it to prevent others
from using it.
Care of Grinding and Cut-Off Wheels
Grinding/cut-off wheels should be protected from:
• wetness and extreme humidity
• any type of solvent
• extreme changes in temperature
• dropping and bumping
Grinding and cut-off wheels should be stored:
• in an organized way so wheels can be removed without
disturbing or damaging other wheels
• with their safety information
USING WIRE BRUSHES
WARNING Everyone in the area must
wear protective clothing and safety goggles
or face shields. Fatigued wires and residue
will y off the brush with considerable force,
causing potential for serious injury.
Wire brushes are useful for removing rust, scale,
burrs, weld slag, etc.
Always install wire cup brushes according to the
accessory manufacturer’s instructions.
Fig. 6
Wire Cup Brush
WARNING Because the wires on wire
wheel brushes are directed towards the operator, a guard must be used to protect the
operator when fatigued wires break.
When using a wire wheel brush, install guard according to "Installing/Removing Accessories".
7
Fig. 7
Guard
Wire Wheel Brush
Test wheel for balance and loose or damaged wires
by letting it spin for one minute before applying it
to the workpiece. During this time, no one should
stand in front of or in line with it.
Control pressure and surface contact between
wheel and workpiece. Too much pressure causes
over-bending of wires and heat build-up causing premature wire breaking, rapid dulling and
reduced brush life. Instead of more pressure, try
a wire wheel with more aggressive cutting action
(increased wire size, decreased wire length or different brush type (knot type vs. crimped wire type).
WARNING Never exceed Maximum
Safe Operating Speed of brush. Do not use
a damaged brush or one that is functioning
improperly (throwing wires, out-of-balance,
etc.). These conditions increase the pos-
sibility of further brush failure and possible
injury. Discard and replace damaged brushes
immediately.
USING SANDING DISCS
Sanding Disc Selection
Use sanding discs and accessories that are:
•
correct size as written on tool’s nameplate.
• rated at or above the RPM listed on the tool’s
nameplate.
• correct accessory, wheel type and grit for the job.
Refer to the table below to select the correct type
of sanding disc for your job. Generally, use 24 or
36 grit for heavy stock removal; 50, 60, or 80 grit
for medium stock removal and 120 grit for nishing.
Always begin with a coarse grit, using successively
ner grits to obtain the desired nish.
For a complete listing of accessories, refer to your
MILWAUKEE® electric tool catalogue or go online to
www.milwaukeetools.com.au /
www.milwaukeetools.co.nz.
To obtain a catalogue, contact your local distributor
or service center.
For fast cutting, general purpose discs for most
metal jobs. Best for cold-rolled steel, stainless
steel or metals requiring tough, fast cutting, long
lasting abrasives.
Unique grit pattern is arranged in clusters for faster stock removal and cleaning. Ideal for removing
paint from cars, boats, etc. without clogging.
Lasts up to 3 times longer than Aluminum Oxide Discs. For general metal working. Ideal for
tough jobs.
Aluminum Oxide
Aluminum Zirconia Bi-Cut
Ceramic
Installing Backing Pad and Sanding Discs
1. Remove the battery pack.
2. Wipe the accessories, disc nut and spindle to
remove dust and debris. Inspect the parts for
damage. Replace if needed.
3. Slip backing pad onto spindle with at side away
from gear case.
4. Place sanding disc on backing pad and secure
assembly to spindle with disc nut.
Fig. 8
Disc nut
Sanding
disc
Backing
pad
Spindle
5. To tighten, press the spindle lock button while
turning disc nut clockwise. Tighten securely.
6. To remove backing pad and sanding disc,
remove the battery pack and reverse the procedure.
Sanding
Hold tool at 5° to 15° angle to ensure proper sanding pressure and control. Too great an angle will
result in too much pressure and could cause excessive wear to the disc and workpiece. Too small an
angle will reduce control.
Use long, sweeping, side to side strokes, advancing
forward to produce the desired nish.
Fig. 9
Hold at a
5° to 15°
angle
For best result use only this portion of disc
8
Cross Sanding
performing any maintenance. Never
When nishing a surface that has been prepared by
a coarse disc or wheel, sand at right angles to the
strokes made by the coarser disc. Finishing marks
left from previous sanding are easily seen and
removed for a uniform nish. Failure to cross sand
when changing from a coarse disc to a nishing disc
may result in deep scratches and circular marks.
Removing Welds or Hammer Marks
When removing welds or hammer marks, limit
coarse sanding to the immediate area. Use suc-
cessively ner grits to smooth surface.
Finishing Metal
Constantly move across the surface. Work faster on
curved surfaces where contact areas are smaller
and pressure is greater. Flat areas may appear at
the end of the stroke when pressure is too heavy.
Ease up on pressure at end of each stroke and
when reversing strokes.
Troubleshooting
Deep scratches and circular marks can result from:
• Using too coarse a grit
• Using a partially glazed disc
• Dirt or loose metal on the workpiece
• Failure to sand across the grain when changing
from coarse to nishing discs
• Failure to use closed coated discs to reduce the
problem of grains working loose and scratching
the workpiece
Bluish discoloration of metal surface indicates:
•
Excessive heat caused by circular motion in a
small area
• Excessive pressure
• Use of worn out or glazed discs
MAINTENANCE
WARNING
always unplug the charger and remove the
battery pack from the charger or tool before
disassemble the tool, battery pack or charger.
Contact to the store where the product was
originally purchased or one of our authorised
MILWAUKEE® service centres for repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance
program.
After six months to one year, depending on use,
return the tool, battery pack and charger to the
store where the product was originally purchased
or one of our authorised MILWAUKEE® service
centres for:
• Lubrication
• Mechanical inspection and cleaning (gears, spindles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger,
motor)
•
Testing to assure proper mechanical and electrical
operation
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work properly, return the tool, charger and battery pack, to a
MILWAUKEE® service facility for repairs.
To reduce the risk of injury,
ACCESSORIES
WARNING Always remove battery pack
before changing or removing accessories.
Only use accessories
ed for this tool. Others may be hazardous.
For a complete listing of accessories, refer to your
MILWAUKEE® electric tool catalogue or go online to
www.milwaukeetools.com.au /
www.milwaukeetools.co.nz.
To obtain a catalogue, contact your local distributor
or service center.
specically recommend-
WARNING To reduce the risk of per-
sonal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to ow inside them.
Cleaning
Clean dust and debris from charger and tool vents.
Keep tool handles clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to
clean the tool, battery pack and charger since certain
cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include
gasoline, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use
ammable or combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger to
the store where the product was originally purchased or
one of our authorised MILWAUKEE® service centres.
9
WARRANTY - AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold in Australia and New Zealand.
AUSTRALIA AND NEW ZEALAND
MILWAUKEE
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy Duty®.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE® dealer.
For a list of MILWAUKEE® dealers, guarantee or service agents please contact MILWAUKEE
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 279 624) or visit www.milwaukeetools.com.au /
www.milwaukeetools.co.nz.
®
Service
®
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Electric Tool Corporation
Milwaukee Electric Tool Corporation (Australia)
Techtronic Industries (Australia) Pty. Ltd.
Doncaster, Victoria, Australia, 3108
Milwaukee Electric Tool Corporation (New Zealand)
Techtronic Industries (New Zealand) Pty. Ltd.
Mangere, Auckland, New Zealand, 2022
Professionally made in China for Milwaukee Electric Tool Corporation
961011583-01(A)
Loading...