Milwaukee 2848-20 Service Parts List

EXAMPLE:

00

Component Parts (Small #) Are Included

0

When Ordering The Assembly (Large #).

TORQUE SPECIFICATION
CHART FOR FASTENERS
LOCATED ON PAGE 4

27 28 32

75

44 70

SERVICE PARTS LIST

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

M18™ INFLATOR

CATALOG NO.

1

(2x)

2

3

4

5

(2x)

6

(2x)

80

26

(2x)

27

(2x)

44

(2x)

45

(2x)

29

28

81

33 34
35

2848-20

STARTING
SERIAL NO.

FIG. NOTES

70,71 A clean, dry surface is essential for proper performance
for any adhesive system. The area intended for applica­ tion of any adhesive label or nameplate must be pre-
pared by cleaning with isopropyl alcohol. Solvent is to
be applied with a clean, lint free applicator
and surface allowed to dry before applying
the label or nameplate.

40

(2x)

41

(2x)

42

46

(2x)

49

50

51

52

M26A

33

34

35

38

70

39

(7x)

43

49 50 51 52 57 58 59

82

60 61 62 63 64 65 43

BULLETIN NO.

54-05-2480

REVISED BULLETIN DATE

Sept 2021

WIRING INSTRUCTION

See pages 2 and 3

32

74

56

73

57

58

56

53

32

(2x)

55

54

53 54
55

32

(10x)

FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 06-82-0269 M3 x 10mm Pan Hd. T-10 Screw (2)

2 42-32-0027 Pump Head (1)
3 22-84-0019 Fan (1)
4 44-52-0082 SBR Pad (1)
5 06-81-0220 M4 x 6mm Pan Wash. Hd. Phillips Screw (2)
6 45-88-0313 Flat Washer (2)
26 44-52-0098 Support Pad (2)
27 44-52-0101 Motor Pad (Small) (2)
28 --------------- Front Housing (1)
29 42-92-0264 Base (1)
30 44-52-0037 Rubber Foot (4)
31 06-81-0221 M4 x 12mm Pan Wash. Hd. T-20 Screw (4)
32 06-81-0222 M4 x 18mm Pan Hd. T-20 Screw (20)
33 --------------- Control Panel (1)
34 --------------- Power Button (1)
35 --------------- Button (1)
38 14-20-0431 PCBA with LCD (1)
39 06-81-0223 M3 x 10mm Pan Hd. Phillips Screw (7)
40 06-81-0224 M4 x 10mm Pan Hd. Phillips Screw (2)
41 31-12-0057 Terminal Cap (1)
42 --------------- Battery Terminal Block (1)
43 --------------- Rear Housing (1)
44 44-52-0107 Motor Pad (Large) (2)
45 22-56-0206 Close End Wire Connectors (2)
46 44-81-0018 Battery Rail (1)
49 --------------- Seal Ring (2)
50 --------------- Hose Connector (1)
51 --------------- Hose Clamp (2)
52 --------------- Hose (1)
53 --------------- Nozzle Adaptor (1)

54 --------------- InatingNeedle (1)
55 --------------- InatingNozzle (1)

56 --------------- Hose Wrap (1)

32

(8x)

30

(4x)

31

(4x)

30

72

31

FIG. PART NO. DESCRIPTION OF PART NO. REQ.
57 --------------- Hose Clip (2)
58 --------------- Hose (1)
59 --------------- 3-Way Connector (1)
60 --------------- Hose Clamp (1)
61 --------------- Hose (1)
62 --------------- Hose Clamp (1)
63 --------------- Connector (1)
64 43-44-0064 Gasket (1)
65 --------------- Air Tap (1)
70 12-20-0239 Service Nameplate (1)
72 42-38-0148 Foot/Screw Service Kit (Set of one) (4)

73 14-46-0331 InatingAttachmentKit (1)

74 14-46-0332 Hose Wrap/Screw Service Kit (1)
75 14-34-0161 Housing Service Kit (1)
80 --------------- Motor/Pump Assembly (1)
81 14-46-0347 Control Panel Service Kit (1)

82 14-37-0123 Hose Assembly (1)

59

60

61

63 64 65 62

MILWAUKEE TOOL l www.milwaukeetool.com

13135 W. LISBON RD., BROOKFIELD, WI 53005

Drwg. 2

WIRING INSTRUCTIONS

Screw the NTC black wire to the pump.

Screw the NTC white wire to the motor.

PUMP

MOTOR

Crimp motor black wire and PCB black wire together using close end connector.
Crimp motor red wire and PCB red wire together using close end connector.

Insert the black NTC terminal into PCBA.

Insert the white NTC terminal into PCBA.

Insert the black and red fan terminal into the PCBA.

WIRING INSTRUCTIONS continued

Place the white NTC
wires into wire traps
as shown.

Place the black NTC wires into wire traps as shown.

Place the red and black fan wires into wire traps as shown.

As an aid to reassembly, take notice of wire routings
and position in wire guides and traps while
dismantling tool.

Be sure that all components of electronics kit are
seated firmly and squarely in housing recesses.

Avoid pinched wires, be sure that all wires and
sleeves are pressed completely down in wire traps.

Prior to securing housing cover onto the housing
support, be sure that there are no interferences.

Place the red and black
motor wires into wire
traps as shown.

Before installing the battery, check for proper
functionality of shuttles and triggers.

Install battery and depress switch triggers to
assure tool is operating properly.

Place close end connectors down into cavity area as shown.

SCREW TORQUE SPECIFICATIONS

SEAT TORQUE
FIG. PART NO. DESCRIPTION OF FASTENER WHERE USED (N.m) (IN/LBS)
1 06-82-0269 M3 x 10mm Pan Hd. T-10 Screw Pump Head and Front Housing/Rear Housing 0.35-0.55 3.097-4.867

5 06-81-0220 M4 x 6mm Pan Wash. Hd. Phillips Screw NTC and Cylinder Cap 0.35-0.55 3.097-4.867
31 06-81-0221 M4 x 12mm Pan Wash. Hd. T-20 Screw Rubber Feet and Base 0.1-0.3 0.885-2.655
32 06-81-0222 M4 x 18mm Pan Hd. T-20 Screw Base and Front Housing/Rear Housing 0.5-0.8 4.425-7.080
32 06-81-0222 M4 x 18mm Pan Hd. T-20 Screw Front Housing and Rear Housing 1.0-1.4 8.850-12.391
32 06-81-0222 M4 x 18mm Pan Hd. T-20 Screw Hose Wrap and Rear Housing 0.75-0.95 6.637-8.407
39 06-81-0223 M3 x 10mm Pan Hd. Phillips Screw PCBA and Control Panel 0.35-0.55 3.097-4.867
40 06-81-0224 M4 x 10mm Pan Hd. Phillips Screw Terminal Cap and Battery Rail 0.75-0.95 6.637-8.407