Milwaukee 2564-20 Service Parts List

EXAMPLE:

00

Component Parts (Small #)

0

Are Included When Ordering
The Assembly (Large #).

SERVICE PARTS LIST

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

M12™ FUEL™ 3/8" Right Angle Impact Wrench w/ Friction Ring

59

STARTING
SERIAL

L18A

58

57

68

CATALOG NO. 2564-20

60

67

BULLETIN NO.

54-26-2430

REVISED BULLETIN

WIRING INSTRUCTION

See Page 2

6

(4x)

54 55 56

66

58 59 60
23

69

24

DATE

Jan. 2020

64

55

54

(5x)

56

FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 49-16-2564 Rubber Boot (Accessory) (1)

6 05-74-0986 M4 x 15mm Pan Hd. T-20 Mach. Screw (4)
23 34-40-1885 Small O-Ring for 3/8" Anvil (1)
24 44-90-1050 Friction Ring for 3/8" Anvil (1)
53 06-82-2738 M3 x 6mm Pan Hd. T-10 Mach. Screw (1)
54 06-82-1080 M3 x 14mm Pan Hd. ST T-10 Screw (5)
55 --------------- Right Handle Halve-Cover (1)
56 12-20-2564 Service Nameplate (1)
57 --------------- Left Handle Halve-Support (1)
58 --------------- Forward/Reverse Shuttle (1)
59 --------------- Rocker Trigger (1)
60 42-70-0058 Housing Connection Clip (1)
64 42-55-2560 Tool Bag (1)
66 31-44-2564 Handle Assembly (1)
67 14-20-2564 Electronics Assembly (1)
68 16-01-2564 Rotor Assembly (1)
69 14-30-2564 Gearcase Assembly-3/8" Anvil w/ FR (1)

53

1

23

24

SEAT TORQUE

SCREW TORQUE SPECIFICATIONS

FIG. PART NO. WHERE USED (KG/CM) (IN/LBS)
6 05-74-0986 Housing/Gearcase 21±1 18±1
53 06-82-2738 Ground Plate 10±1 8±1
54 06-82-1080 Housing Cover 10±1 8±1

MILWAUKEE TOOL l www.milwaukeetool.com

13135 W. LISBON RD., BROOKFIELD, WI 53005

Drwg. 1

WIRING INSTRUCTIONS

1. HV wire in wire traps

HV terminal

Align HV
terminal
as shown

2. Seat PCBA in recesses

5. Route cable through this groove

Housing
Connection
Clip

3. Place wires in traps

6. Place switch, forward/reverse shuttle
and trigger in handle support recesses
as shown

4. Place LED light in recess with the red wire to the top

7. Be sure that
trigger aligns with
rib as shown

8. Place battery terminal block
firmly and squarely in handle
recess.

Switch Trigger Fwd/Rev Shuttle LED PCBAs Rotor Assy. Stator Assy. HV Term.

Prior to installing the Housing Cover, be sure all elements of the
Electronics Assembly are seated properly (Stator, Main PCBA, Selector
PCBA, On-Off Switch, LED Assembly and Battery Terminal Block
Connector). Be sure the Grounding Terminal is in place and that all wires
are pressed down into all wire traps and channels. Check to assure that

wires will not interfere with moving parts. Prior to installing the Housing
Cover, place Forward/Reverse Shuttle onto On-Off Switch and through
Housing Support opening. Check to assure that wires will not be pinched.
Secure the Housing Cover to the Housing Support with five M3 x 16mm
ST T-10 Screws. Be sure to replace the Housing Clip at the bottom of the
battery opening.