Milwaukee 2407-20 User Manual

EXAMPLE:

00

Component Parts (Small #)

0

Are Included When Ordering
The Assembly (Large #).

32 33 31 30

12 14 19 20

39

21 23 30

SERVICE PARTS LIST

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

Cordless M12™ 3/8" Driver-Drill

CATALOG NO. 2407-20

15(2x)

STARTING
SERIAL NO.

8(2x) 24 9

35

16

F10A

BULLETIN NO.

54-06-2490

REVISED BULLETIN

WIRING INSTRUCTION

SEE REVERSE SIDE

Original

*

Design
42-70-0055

M12™ tools utilize two different Housing
Connection Clip designs depending on the
Handle Set . See page two for details.

DATE

Feb. 2014

42-70-0058

Improved

Design

2

1

16

29

See detail above

38

*

34

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

1 05-88-1680 M5 x 0.8 x 18.5mm LH Chuck Screw (1)
2 42-66-0825 3/8" Keyless Chuck (1)
8 05-81-0542 M2.3 x 4.5mm ST Screw (2)
9 44-10-0710 Speed Selector Lever (1)
12 06-82-1080 M3.0 x 14mm Pan Hd. T-10 ST Screw (7)
14 --------------- Housing Cover (Right Handle Halve) (1)
15 --------------- M3 x 6mm Screw (2)
16 44-66-1585 Motor Mount Plate (1)
19 12-20-2407 Service Nameplate (1)
20 10-20-2810 Warning Label (Not Shown) (1)
23 31-01-0003 Light Pipe (1)
24 45-24-0325 Speed Selector Slide Button (1)
25 42-42-0820 Forward/Reverse Shuttle (1)
26 40-50-1135 Shuttle Spring Plate (1)
29 42-70-0055 Housing Connection Clip (1)
30 --------------- Housing Support (Left Handle Halve) (1)
31 --------------- Fuel Gauge Label (1)
32 05-88-1010 M2.5 x 6mm Pan Hd. Phillips Screw (1)
33 42-70-0580 Belt Clip (1)
34 14-50-2430 Service Motor Assembly with Pinion (1)
35 14-29-0825 Service Gearcase Assembly (1)
38 42-55-2105 Carrying Case (1)
39 14-38-0250 Service Housing Set (1)
40 23-66-1795 Service Switch/Electronics Assembly (1)

15
16

25

26

23

40

19

14

12(7x)

FIG. NOTES:

16,34,35 Service replacement gearcase assembly (35) comes with a

motor mount plate (16) that must be removed and discarded
when servicing. A motor mount plate already exists on the
motor assembly (34).

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 W. Lisbon Road, Brookfi eld, WI 53005

Drwg. 5

Slots

Early M12™ Handle Sets utilize Housing
Connection Clip No. 42-70-0055. Install this
clip design by aligning the side rails of the clip
with the two slots in the handle set. Gently
push into place with the aid of a small flat
blade screwdriver or a similar instrument. Be
sure that the clip is properly seated in both
slots and that the clip is flush to sub-flush to
the end of the handle set. To remove the clip,
use the same small flat blade screwdriver or a
similar instrument and push the clip out of the
handle set. If the clip is loose or will not stay in
place, a needle nose pliers can be used to
gently bend/pinch the side rails of the clip. If
the clip is damaged do not use, replace with a
new 42-70-0055 housing clip.

Recess in early handle
sets may only have the
slots to accommodate a
housing clip. Use 42-70-0055
only in this situation.

Slots

Dimples

Recess in this
handle set design
has slots and dimples
to secure a housing clip.
The 42-70-0055 can be
used but the 42-70-0058 is
preferred in this situation.

42-70-0055

Updated M12™ Handle Sets utilize Housing
Connection Clips No. 42-70-0055 and 42-70-

0058. (The 42-70-0058 is a preferred upgrade).

Install this clip design by aligning the side rails
of the clip with the two slots in the handle set.
Gently push into place with the aid of a small
flat blade screwdriver or a similar instrument.
Be sure that the clip is properly seated in both
slots and that the tab of the clip snaps down in
the round dimpled cavity of the handle set. Be
sure that the clip is flush to sub-flush to the end
of the handle set. To remove the clip, use the
same small flat blade screwdriver or a similar
instrument and lift up on the clip tab while
pushing the clip out of the handle set. Use a
needle nose pliers to gently rebend the clip tab
if necessary. If the tab on the clip is damaged
during this process and is loose or will not stay
in place, replace with a new 42-70-0058 clip.

42-70-0058

Slots
Dimple
Tab Cavity
Recess in newer handle

sets have two slots, a
dimple and a tab cavity to
accommodate the newer
housing clip design.

Newer M12™ Handle Sets utilize Housing
Connection Clip No. 42-70-0058. Install this
clip design by aligning the side rails of the clip
with the two slots in the handle set. Gently
push into place with the aid of a small flat blade
screwdriver or a similar instrument. Be sure
that the clip is properly seated in both slots and
that the tab of the clip snaps down in the
rectangular cavity of the handle set. Be sure
that the clip is flush to sub-flush to the end of
the handle set. To remove the clip, use the
same small flat blade screwdriver or a similar
instrument and lift the clip tab out of the cavity
while pushing the clip out of the handle set.
Use a needle nose pliers to gently rebend the
clip tab if necessary. If the tab on the clip is
damaged during this process and is loose or
will not stay in place, replace with a new
42-70-0058 clip.

42-70-0058