Milwaukee 1670-1, 1675-1, 1678-20, 1679-20 Operating Instructions Manual
Installing Bits into Keyed Chucks (Fig. 1)
1. Unplug tool.
2. Open the chuck jaws
wide enough to insert the
bit. Be sure the bit shank
and chuck jaws are clean.
Dirt particles may prevent
the bit from lining up properly.
3. Insert the bit into the chuck. Center the bit in the chuck jaws
and lift it about 1/16” off of the bottom. Then, tighten the
chuck jaws by hand to align the bit.
4. Place the chuck key in each of the three holes in the chuck,
turning it clockwise as shown. Tighten securely.
5. To remove the bit, insert the chuck key into one of the
holes in the chuck and turn it counterclockwise.
Bit Selection
Use sharp bits. Sharp bits are less likely to bind when drilling.
Use the proper bit for the job. There are many types of bits
designed for specific purposes. Check the informa
tion on the bit’s packaging for proper usage.
Do not use bits larger than the rated capacity of the drill.
Gear damage or motor overload may result. See
Specifications on page 4.
Removing and replacing
Quik-Lok®Cords (Fig. 2)
MILWAUKEE’S exclusive
Quik-Lok® Cords provide
instant field replacement or
substitution.
1. Unplug tool from electrical outlet.
2. To remove the Quik-Lok®
Cord, turn the cord nut 1 /4
turn to the left and pull it out.
3. To replace the Quik-Lok Cord, align the connector keyways
and push the connector in as far as it will go. Turn the cord nut
1/4 to the right to lock. (See Fig. 2)
Pipe Handle (Fig. 3)
The pipe handle may be used on either side of the tool. Thread
pipe handle into one of the threaded holes in the motor housing. (See Fig. 3)
Spade Handle (Fig. 4)
The spade handle can be attached to the tool
in three positions as shown in Fig. 4.
Remove the hex head screws which secure
the handle. Remove the handle and move it
to the desired position. To mount the handle
in position C, it is necessary to reverse the
mounting holes by turning the handle
around.
Milwaukee Tool
Heavy-Duty Hole Hawg®
Model Numbers: 1670-1, 1675-1, 1678-20, 1679-20
Operating Instructions
Page 1
RenTrain INC
RenTrain INC
To reduce the risk of injury, always unplug tool
before attaching or removing accessories. Use
only specifically recommended accessories.
Others may be hazardous.
WARNING!
ASSEMBLY
Fig. 1
Fig. 2
Fig. 3
Fig. 4
A
B
C
(Continued on next page)
Bit binding (Fig. 5)
Bit binding (Contined)
If the bit binds, the drill will suddenly react in the opposite
direction of the rotation of the bit. Figure 5 shows the path of
reaction, (B) if the drill bit binds while being driven in forward (A). The operator should reduce the chances of a sudden reaction by following the instructions listed below.
The operator should also prepare for a sudden reaction by
holding securely using the pipe handle or bracing against a
solid fixed object.
See bracing instructions are on page 3.
To reduce the chance of bit binding
• Use sharp bits. Sharp bits are less likely to bind
when drilling.
• Use the proper bit for the job. There are many types
of bits designed for specific purposes.
• Use the proper speed for the size bit. Larger bits
should be run at the lower speed (specifications on
page 3). Driving larger bits at high speeds will
increase the chance of the bit binding and increase
the chance of reaction.
• Avoid drilling warped, wet, knotty, and or pitchy
material if possible.
• Avoid drilling in material that you suspect contains
hidden nails or other things that may cause the bit to
bind.
The direction of reaction is always opposite of the direction of
bit rotation.
Reaction is even more likely to occur when enlarging already
existing holes and at the point when the bit breaks through the
other side of the material.
(Continued on next page)
Operating Instructions (continued)
Page 2
RenTrain INC
RenTrain INC
To reduce the risk of personal injury when
drilling, hold tool by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live”
and shock the operator.
WARNING!
When drilling with a single speed drill or in HI
with a two-speed drill, always hold the drill
securely using the pipe handle, or brace the
drill against a solid fixed object in preparation
for a sudden reaction. When drilling in LO with
a two-speed drill, always brace the drill against
a solid fixed object in preparation for a sudden
reaction.
When drilling, never use your body to brace
drill.
Never put your hands (or other body parts)
between the part of the drill being braced and
the object it is being braced against. Hands (or
other body parts) that are in the path of the
reaction can be pinched, crushed and broken.
See Bracing Instructions, Page 3 Figures 6 & 7.
WARNING!
OPERATION
B
A
Loading...