Milwaukee 1400 Owner's Manual

EnglishEspañol Français

1-800-727-4023

Wagner Technical Service

http://www.wagnerspraytech.com

Or visit us on the world wide web!

Need help? Call us first for answers fast.

Call Wagner toll-free if you have any comments
or problems with this Wagner product.

1770 Fernbrook Lane, Minneapolis, MN 55447

0503 • Form No. 0283787D

Heat Tool

Model 1400

Owner’s Manual

Read all instructions and product labels. When using electrical tools, follow all
precautions to reduce the risk of fire, electric shock, and other personal injury.

MHT Products, Inc.

by Wagner Spray Tech
1770 Fernbrook Lane
Plymouth, MN 55447
1-800-727-4023

56M8

0283787D.qxd 6/11/03 1:33 PM Page 1

English

2 ©2003 MHT Products, Inc. All rights reserved.

GENERAL DESCRIPTION

The Precision Heat Tool is a quality power tool. Like any other power tool, the Precision
Heat Tool Model 1400 can be dangerous when misused. Read the following instructions
carefully and follow all safety precautions. It is the responsibility of the owner to use the
Precision Heat Tool properly.

Specifications

• 120 Volts / 3A/ 360W / 1250 BTU’s

• 650°F NOMINAL

• Weight - 13 ounces

• Cord - 18 gauge 2 wire, 6 feet long

• Double insulated to minimize electrical risk

Uses

• Soften paint, caulking and putty for easier removal

• Soften adhesives to help remove stickers and floor tiles

• Bend plastic pipes

• Shrink tubing for electrical work

• Shrink plastic film for crafts, wrapping or weatherproofing

• Activate embossing powder and liquid applique for craft use

Servicing of a double-insulated product

In a double-insulated product, two systems of insulation are provided instead of
grounding. No grounding means is provided on a double-insulated product, nor should a
means for grounding be added to the product. Servicing of a double-insulated product
requires extreme care and knowledge of the system, and should be done only by
qualified service personnel. Replacement parts for a double-insulated product must be
identical to those parts in the product.

Precision Heat Tool Model 1400

SAVE THESE INSTRUCTIONS

Important Safety Instructions

Read these instructions

Hazard: POISON - Extreme care should be taken when stripping paint. The

peelings, residue and vapors of paint may contain lead, which is
poisonous. Any paint applied to homes before 1950 is likely to
contain lead. Any paint manufactured before 1977 may contain lead.
Once the paint is deposited on surfaces, hand-to-mouth contact can
result in the ingestion of lead. Exposure to even low levels of lead
can cause irreversible brain and nervous system damage. Young and
unborn children are particularly vulnerable to lead poisoning.

Before beginning any paint removal process you should determine
whether the paint you are removing contains lead. This can be done
by your local health department or by a professional who uses a paint
analyzer to check the lead content of the paint to be removed. Lead­based paint should only be removed by a professional and should
not be removed using a heat gun.

Prevention:

1. Move the work piece outdoors. If this is not possible, keep the work area well ventilated.
Open the windows and put an exhaust fan in one of them. Be sure the fan is moving the
air from inside to outside.

0283787D.qxd 6/11/03 1:33 PM Page 2

WARNING

SAVE THESE INSTRUCTIONS

English

©2003 MHT Products, Inc. All rights reserved. 3

Precision Heat Tool Model 1400

2. Remove or cover any carpets, rugs, furniture, clothing, cooking utensils and air ducts.

3. Place drop cloths in the work area to catch any paint chips or peelings. Wear protective
clothing such as extra work shirts, overalls and hats.

4. W ork in one room at a time. Furnishings should be removed or placed in the center of the
room and covered. Work areas should be sealed off from the rest of the dwelling by
sealing doorways with drop cloths.

5. Children, pregnant or potentially pregnant women and nursing mothers should not be
present in the work area until the work is done and all cleanup is complete.

6. Wear a dust respirator mask or a dual filter respirator mask for dust and fumes which has
been approved by the Occupational Safety and Health Administration (OSHA) the National
Institute of Safety and Health (NIOSH), or the United States Bureau of Mines. These
masks and replaceable filters are readily available at major hardware stores. Be sure that
the mask fits properly. Beards and facial hair may keep masks from sealing properly.
Change the filters often. Disposable paper masks are not adequate.

7. Use caution when operating the heat gun. Keep the heat gun moving as excessive heat
will generate fumes which can be inhaled by the operator.

8. Keep food and drink out of the work area. Wash hands, arms and face and rinse mouth
before eating or drinking. Do not smoke or chew gum or tobacco in the work area.

9. Clean up all removed paint and dust by wet mopping the floors. Use a wet cloth to clean
all walls, sills and any other surface where paint dust is clinging. Do not sweep, dry dust or
vacuum. Use a high phosphate detergent of trisodium phosphate (TSP) to wash and mop
areas.

10. At the end of each work session, put the paint chips and debris in a double plastic bag,
close it with tape or twist ties and dispose of properly.

11 . Remove protective clothing and work shoes in the work area to avoid carrying dust into

the rest of the building. Wash work clothes separately. Wipe shoes off with a wet
rag and then wash it with the work clothes. Wash hair and body thoroughly with
soap and water.

HAZARD: EXPLOSION OR FIRE - This heat gun produces extremely high

temperatures (as high as 1200° F). It must be used with caution to
prevent combustible material from igniting.

PREVENTION:

1. Keep the heat gun in constant motion. Do not stop or dwell in one spot.

2. Use extreme caution if the other side of the
material being scraped is inaccessible, such
as house siding. The hidden side could catch
on fire if it becomes too hot. Some buildings
contain highly flammable materials behind
siding, floors, facia, soffit boards and other
panels. Check these areas before applying
heat and do not use a heat tool if flammable
materials are present or if you are unsure of
the hidden material.

3. Do not use near surfaces with cracks or near metal pipes or flashing. Heat may be
conducted behind the work surface and ignite hidden material. The ignition of
hidden materials may not be readily apparent and can result in property damage
and injury.

4. Do not use electric tools in the presence of flammable liquids or gases.

5. Do not use near combustible materials such as dry grass, leaves, and paper which
can scorch and catch fire.

0283787D.qxd 6/11/03 1:33 PM Page 3

WARNING

Inside

Wall

Facia
Soffit

Siding

English

4 ©2003 MHT Products, Inc. All rights reserved.

Precision Heat Tool Model 1400

6. The nozzle becomes very hot. Do not lay the heat gun on flammable surfaces
when operating the heat gun or immediately after shutting the heat gun off. Always
set the gun on a flat, level surface so that the nozzle tip is directed upwards and
away from the supporting surface.

7. Do not touch the nozzle until the tool has cooled.

8. Do not use the heat gun as a hair dryer.

9. Tools and paint scrapings become very hot. To avoid burns, use work gloves when
scraping.

10. Always treat the hot air units with the same respect as an open flame.

HAZARD: ELECTRIC - may cause property damage, severe injury or loss of life.
PREVENTION:

1. Do not disassemble the heat gun.

2. Do not work in wet areas or expose the heat gun to rain.

3. Guard against electric shock by preventing body contact with grounded surfaces
such as pipes, radiators, ranges, aluminum ladders or other grounded devices.

4. Do not abuse the electric cord. Never carry the heat gun by the cord or yank on
the cord to disconnect if from the power supply. Keep the electric cord away from
heat, oil and sharp edges. Inspect the cord for wear or damage regularly.

5. Use only extension cords rated for outdoor use. If an extension cord is damaged
or otherwise unsuitable for use, replace it with a new cord.

HAZARD: GENERAL - may cause property damage or severe injury.

PREVENTION:

1. Disconnect the heat gun from the power supply when not in use. Store indoors in
a dry place and out of the reach of children.

2. Keep your work area well lighted and clean.

3. Do not overreach, especially when working on ladders. Keep proper footing and
balance at all times. Be certain any ladders being used are sturdy, stable, on a
firm surface and erected at safe working angles.

4. Avoid power lines.

5. Keep moveable items secured and steady while scraping.

6. Always use protective eyewear when working.

7. Stay alert and use common sense when operating any tool.

HAZARD: VIBRATION - may cause hand injury

PREVENTION:

1. Avoid prolonged exposure to vibration.

Some dust, peelings, residue, and vapors caused by paint removal activities contain
chemicals known to the state of California to cause birth defects or other reproductive
harm. An example of a chemical would be lead from lead-based paints (do not use a
heat tool to remove lead-based paint). Your risk from exposure varies, depending on
how often you do this type of work. To reduce your exposure to these chemicals: work
in a ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.

SAVE THESE INSTRUCTIONS

0283787D.qxd 6/11/03 1:33 PM Page 4

WARNING

WARNING

English

USING THE HEAT TOOL

1. Plug the unit into a standard wall outlet.

2. Turn on the unit. The motor-driven fan noise will indicate that the unit is running.
The heating coil will light up slowly to dark red.

3. When you are done, turn the unit off and set it down with the nozzle pointing up and
the stand in the support position.

STORAGE

Allow the hot tool nozzle to cool to room temperature before placing in storage.
The nozzle will turn dark over time because of the high heat. This is normal and will not

affect the performance or life of the unit.

USES

Embossing

When using the hot tool to activate embossing powder, remove excess powder by
dusting the powder off with a clean, dry paint brush. Hold the nozzle end of the hot tool
approximately 3 inches (77 MM) from the work surface. To prevent the paper from
becoming too hot, move the nozzle end around in a circular fashion until the embossing
powder is raised and shiny.

When you have completed one area, switch the hot tool off and return the tool to its built­in stand while preparing another area.

NOTE: Keep the nozzle pointed up after shutdown, either for a short

break or for storage. If the nozzle is pointed down, the residual
heat rises into the motor space and shortens the life of the unit.
Avoid laying the unit on the side after shutdown. The heat will
remain in the unit and cooling will take longer. Store the unit
only after the nozzle is cool to touch. Unplug the unit before
storing to prevent accidental start up.

NOTE: Smoke may appear during the initial start up due to the burning

of manufacturing oils. The smoke should disappear in less than
a minute.

©2003 MHT Products, Inc. All rights reserved. 5

Precision Heat Tool Model 1400

0283787D.qxd 6/11/03 1:33 PM Page 5

English

6 ©2003 MHT Products, Inc. All rights reserved.

Stripping Paint

The Precision Heat Tool does not overheat the surface or scorch wood easily, unlike
radiant heat and open flame devices such as a propane torch. The heat tool heats up
the surface and causes the paint to soften, at which time it can be scraped off easily
without damaging the surface.

Only oil paints were used prior to 1942, and such paints soften easily with heat and can
be scraped off as soon as the finish has blistered. Today's paints are more varied, so
generalized results cannot be predicted. Some paints may soften even though they do
not blister; some may become rubbery, and some may require higher heat.

When working with several layers of paint, it speeds up the scraping process to heat the
surface thoroughly, all the way to the wood. Then all the layers can be scraped at one
time.

A soft wire brush may be the best tool to use for very intricate surfaces. Mineral paints
and finishes, such as cement paint and porcelain, do not soften with heat, so using a
heating tool will not work for paint removal.

Bending Plastic Pipe

Heat all around the pipe from a distance of 2 to 6 inches. Continue heating until the
pipe feels soft and can be bent with little resistance. Hold the bent pipe until it is cold.
Overbend the pipe a little because it will spring back some after release.

Shrink Wrapping

Wrap the object with heat-shrinkable plastic film. Begin to heat the film from a safe
distance while keeping the hot tool moving. Move the hot tool closer to the film until the
film starts to shrink and becomes taut.

Shrink Tubing

The shrink tube accessory can be used whenever circular airflow is required. It is often
used to shrink the tubing around electrical connections, or to soften a plastic tube that
must be bent at a specific location. (See Bending Plastic Pipe). The shrink tube
accessory (part number 0503153) can be purchased by calling 1-800-727-4023.

The shrink tube attachment becomes very hot during use. Allow the attachment to
cool before removal or storage.

Slide the shrink tube attachment over the nozzle of the heat tool. Use this
attachment only to shrink tubing. Attach only when the heat tool is cool to touch.

Precision Heat Tool Model 1400

0283787D.qxd 6/11/03 1:33 PM Page 6

CAUTION

English

PRODUCT REGISTRATION CARD

Please fill out and return the enclosed product registration card. Proper registration will
serve as proof of purchase in the event your original receipt becomes misplaced or lost.
Returning this card will not affect warranty coverage, but may expedite the processing of
your warranty and enable you to contact us in the event of loss or theft. The additional
information will also help us to develop new products that best meet your needs and
desires. Thank you!

TWO YEAR LIMITED WARRANTY

Keep on file

This product is warranted against defects in material and workmanship for two years
following the date of purchase if operated in accordance with printed recommendations
and instructions. This warranty does not cover any defects or damages caused by
service or repair performed by unauthorized personnel.

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR APARTICULAR
PURPOSE IS LIMITED TO TWO YEARS FOLLOWING THE DATE OF PURCHASE.
WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF THE
WARRANTY OR ANY OTHER REASON. THIS WARRANTY DOES NOT APPLY TO
ACCESSORIES.

If any product is defective in material and workmanship during the applicable warranty
period, return it with proof of purchase to where it was purchased for replacement.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OF INCIDENTALOR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO
YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

©2003 MHT Products, Inc. All rights reserved. 7

Precision Heat Tool Model 1400

0283787D.qxd 6/11/03 1:33 PM Page 7

0283787D.qxd 6/11/03 1:33 PM Page 8