Miller Electric Big 40 WG User Manual

OM-4405 200 972A

January 2001

Processes

Stick (SMAW) Welding

TIG (GTAW) Welding

MIG (GMAW) Welding

Flux Cored (FCAW) Welding

Air Carbon Arc (CAC-A)
Cutting and Gouging

Descriptio n

Engine Driven Welding Generator



Big 40 WG

Visit our website at

www.MillerWelds.com

From Miller to You

Thank you and congratulations on choosing Miller.
Now you can get the job done and get it done right. We
know you don’t have time to do it any other way.

That’s why when Niels Miller first started building arc
welders in 1929, he made sure his products offered
long-lasting value and superior quality. Like you, his
customers couldn’t afford anything less. Miller
products had to be more than the best they could be.
They had to be the best you could buy.

Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.

This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.

We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will

Miller is the first welding
equipment manufacturer in
the U.S.A. to be registered to
the ISO 9001 Quality System
Standard.

help you figure out what the problem is. The
parts list will then help you to decide which
exact part you may need to fix the problem.
Warranty and service information for your
particular model are also provided.

Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor
to receive the latest full line catalog or
individual catalog sheets. To locate your nearest

distributor or service agency call 1-800-4-A-Miller,
or visit us at www.MillerWelds.com on the web.

Working as hard as you do
– every power source from
Miller is backed by the most
hassle-free warranty in the
business.

Miller offers a Technical
Manual which provides
more detailed service and
parts information for your
unit. T o obtain a Technical
Manual, contact your local
distributor. Your distributor
can also supply you with
Welding Process Manuals
such as SMAW, GTAW,
GMAW, and GMA W-P.

WARNING

This product, when used
for welding or cutting,
produces fumes or
gases which contain
chemicals known to the
State of California to
cause birth defects and,
in some cases, cancer.
(California Health &
Safety Code Section

25249.5 et seq.)

WARNING

TABLE OF CONTENTS

SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1. Symbol Usage 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Arc Welding Hazards 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Engine Hazards 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. Additional Symbols For Installation, Operation, And Maintenance 3. . . . . . . . . . . . . . . . . . . . .

1-5. Principal Safety Standards 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. EMF Information 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT UTILISA TION 5. . . . . . . . . . . . . . . . . . . . .

1-1. Signification des symboles 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Dangers relatifs au soudage à l’arc 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Dangers existant en relation avec le moteur 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. Dangers supplémentaires en relation avec l’installation, le fonctionnement

et la maintenance 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Principales normes de sécurité 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. Information sur les champs électromagnétiques 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery posts, terminals
and related accessories
contain lead and lead
compounds, chemicals
known to the State of
California to cause
cancer and birth defects
or other reproductive
harm. Wash hands after
handling.

WARNING

The engine exhaust from
this product contains
chemicals known to the
State of California to
cause cancer, birth
defects, or other
reproductive harm.

The following terms are
used interchangeably
throughout this manual:

Stick = SMAW
TIG = GTA W
MIG = GMAW

SECTION 2 – DEFINITIONS 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1. Symbols And Definitions 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 – SPECIFICATIONS 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1. Weld, Power, And Engine Specifications 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. Dimensions, Weights, And Operating Angles 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3. Volt-Ampere Curves For CC Models 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4. Volt-Ampere Curves for CC/CV Models 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-5. Fuel Consumption 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-6. Duty Cycle And Overheating 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-7. AC Auxiliary P o w e r C u r v e 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-8. Optional AC Power Plant Curves 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 – INSTALLATION 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1. Installing Welding Generator (See Sections 4-2 And 4-3) 14. . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Using Lifting Eye 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-3. Mounting Welding Generator 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-4. Installing Exhaust Pipe 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-5. Activating The Dry Charge Battery (If Applicable) 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-6. Connecting The Battery 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-7. Engine Prestart Checks 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-8. Connecting To Weld Output Terminals 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-9. Selecting Weld Cable Sizes 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-10. Connecting To Remote Amperage Adjust Receptacle RC13 On CC Models 20. . . . . . . . . . . . .

4-11. Connecting To Remote 14 Receptacle RC14 On CC/CV Models 21. . . . . . . . . . . . . . . . . . . . . .

SECTION 5 – OPERATING WELDING GENERATOR – CC MODELS 22. . . . . . . . . . . . . . . . . . . . . . . . .

5-1. Front Panel Controls For CC Models (See Section 5-2) 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Description Of Front Panel Controls For CC Models (See Section 5-1) 23. . . . . . . . . . . . . . . . .

5-3. Remote Amperage Control On CC Models (Optional) 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 6 – OPERATING WELDING GENERATOR – CC/CV MODELS 26. . . . . . . . . . . . . . . . . . . . . .

6-1. Front Panel Controls For CC/CV Models (See Section 6-2) 26. . . . . . . . . . . . . . . . . . . . . . . . . .

6-2. Description Of Front Panel Controls For CC/CV Models (See Section 6-1) 27. . . . . . . . . . . . . .

6-3. Process/Contactor Switch On CC/CV Models 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4. Remote Voltage/Amperage Control On CC/CV Models (Optional) 29. . . . . . . . . . . . . . . . . . . . .

SECTION 7 – OPERATING AUXILIAR Y EQUIPMENT 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-1. 120 Volt And 240 Volt Duplex Receptacles 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-2. Connecting To Optional Auxiliary Power Plant (CC/CV Models Only) 31. . . . . . . . . . . . . . . . . .

7-3. Optional Auxiliary Power Receptacles 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

(Continued)

TABLE OF CONTENTS

SECTION 8 – MAINTENANCE & TROUBLESHOOTING 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-1. Maintenance Label 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-2. Routine Maintenance 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-3. Inspecting And Cleaning Optional Spark Arrestor Muffler 35. . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-4. Servicing Air Cleaner 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-5. Adjusting Engine Weld/Power Speed 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-6. Adjusting Engine Idle Speed 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-7. Adjusting Governor Sensitivity 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-9. Servicing Fuel And Lubrication Systems 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-10. Overload Protection 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-11. Diagnosing Causes Of Engine Fault Shutdowns 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-12. Troubleshooting 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 9 – ELECTRICAL DIAGRAMS 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 10 – AUXILIARY POWER GUIDELINES 52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 11 – PARTS LIST 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPTIONS AND ACCESSORIES
WARRANTY

SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING

rom _nd_11/98

1-1. Symbol Usage

Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.

 Marks a special safety message.

 Means “Note”; not safety related.

1-2. Arc Welding Hazards

 The symbols shown below are used throughout this manual to

call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-5. Read and follow all
Safety Standards.

 Only qualified persons should install, operate, maintain, and

repair this unit.

 During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input

power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.

 Do not touch live electrical parts.
 Wear dry, hole-free insulating gloves and body protection.
 Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work
or ground.

 Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

 Use AC output ONLY if required for the welding process.
 If AC output is required, use remote output control if present on

unit.

 Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).

 Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

 Always verify the supply ground – check and be sure that input

power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.

 When making input connections, attach proper grounding conduc-

tor first – double-check connections.

 Frequently inspect input power cord for damage or bare wiring –

replace cord immediately if damaged – bare wiring can kill.

 Turn off all equipment when not in use.
 Do not use worn, damaged, undersized, or poorly spliced cables.
 Do not drape cables over your body.
 If earth grounding of the workpiece is required, ground it directly

with a separate cable.

 Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

 Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.

 Wear a safety harness if working above floor level.
 Keep all panels and covers securely in place.
 Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

 Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

 Do not connect more than one electrode or work cable to any

single weld output terminal.

SIGNIFICANT DC VOLTAGE exists after stopping
engine on inverters.

 Stop engine on inverter and discharge input capacitors according

to instructions in Maintenance Section before touching any parts.

ARC RAYS can burn eyes and skin.

Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly of f from t h e
weld.

 Wear a welding helmet fitted with a proper shade of filter to protect

your face and eyes from arc rays and sparks when welding or
watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards).

 Wear approved safety glasses with side shields under your

helmet.

 Use protective screens or barriers to protect others from flash and

glare; warn others not to watch the arc.

 Wear protective clothing made from durable, flame-resistant mate-

rial (wool and leather) and foot protection.

FUMES AND GASES can be hazardous.

Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.

 Keep your head out of the fumes. Do not breathe the fumes.
 If inside, ventilate the area and/or use exhaust at the arc to remove

welding fumes and gases.

 If ventilation is poor, use an approved air-supplied respirator.
 Read the Material Safety Data Sheets (MSDSs) and the

manufacturer’s instructions for metals, consumables, coatings,
cleaners, and degreasers.

 Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch­person nearby. Welding fumes and gases can displace air and
lower th e oxygen level causing injury or death. Be sure the breath­ing air is safe.

 Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.

 Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and if necessary, while wearing an
air-supplied respirator. The coatings and any metals containing
these elements can give off toxic fumes if welded.

OM-4405 Page 1

WELDING can cause fire or explosion.

HOT PARTS can cause severe burns.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.

 Protect yourself and others from flying sparks and hot metal.
 Do not weld where flying sparks can strike flammable material.
 Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

 Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

 Watch for fire, and keep a fire extinguisher nearby.
 Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

 Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see
Safety Standards).

 Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.

 Do not use welder to thaw frozen pipes.
 Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

 Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

 Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

FLYING METAL can injure eyes.

 Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,
they can throw off slag.

 Wear approved safety glasses with side

shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

 Shut off shielding gas supply when not in use.
 Always ventilate confined spaces or use ap-

proved air-supplied respirator.

 Allow cooling period before maintaining.
 Wear protective gloves and clothing when

working on a hot engine.

 Do not touch hot engine parts or just-welded

parts bare-handed.

NOISE can damage hearing.

Noise from some processes or equipment can
damage hearing.

 Wear approved ear protection if noise level is

high.

MAGNETIC FIELDS can affect pacemakers.

 Pacemaker wearers keep away.
 Wearers should consult their doctor before

going near arc welding, gouging, or spot
welding operations.

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.

 Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, slag, open flames, sparks, and arcs.

 Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

 Keep cylinders away from any welding or other electrical circuits.
 Never drape a welding torch over a gas cylinder.
 Never allow a welding electrode to touch any cylinder.
 Never weld on a pressurized cylinder – explosion will result.
 Use only correct shielding gas cylinders, regulators, hoses, and fit-

tings designed for the specific application; maintain them and
associated parts in good condition.

 Turn face away from valve outlet when opening cylinder valve.
 Keep protective cap in place over valve except when cylinder is in

use or connected for use.

 Read and follow instructions on compressed gas cylinders,

associated equipment, and CGA publication P-1 listed in Safety
Standards.

1-3. Engine Hazards

FUEL can cause fire or explosion.

 Stop engine and let it cool of f before checking or

adding fuel.

 Do not add fuel while smoking or if unit is near

any sparks or open flames.

 Do not overfill tank – allow room for fuel to expand.

 Do not spill fuel. If fuel is spilled, clean up before starting engine.

 Dispose of rags in a fireproof container.

OM-4405 Page 2

STEAM AND HOT COOLANT can burn.

 If possible, check coolant level when engine is

cold to avoid scalding.

 Always check coolant level at overflow tank, if

present on unit, instead of radiator (unless told
otherwise in maintenance section or engine
manual).

 If the engine is warm, checking is needed, and

there is no overflow tank, follow the next two
statements.

 Wear safety glasses and gloves and put a rag over radiator cap.
 Turn cap slightly and let pressure escape slowly before completely

removing cap.

MOVING PARTS can cause injury.

 Keep away from fans, belts, and rotors.
 Keep all doors, panels, covers, and guards

closed and securely in place.

 Stop engine before installing or connecting unit.
 Have only qualified people remove guards or covers for maint-

enance and troubleshooting as necessary.

 To prevent accidental starting during servicing, disconnect

negative ( –) battery cable from battery.

 Keep hands, hair, loose clothing, and tools away from moving

parts.

 Reinstall panels or guards and close doors when servicing is

finished and before starting engine.

 Before working on generator, remove spark plugs or injectors to

keep engine from kicking back or starting.

 Block flywheel so that it will not turn while working on generator

components.

BATTERY EXPLOSION can BLIND.

 Always wear a face shield, rubber gloves, and

protective clothing when working on a battery.

 Stop engine before disconnecting or connect-

ing battery cables or servicing battery.

 Do not allow tools to cause sparks when working on a battery.
 Do not use welder to charge batteries or jump start vehicles.
 Observe correct polarity (+ and –) on batteries.
 Disconnect negative (–) cable first and connect it last.

BATTERY ACID can BURN SKIN and
EYES.

 Do not tip battery.
 Replace damaged battery.
 Flush eyes and skin immediately with water.

ENGINE EXHAUST GASES can kill.

 Use equipment outside in open, well-ventilated

areas.

 If used in a closed area, vent engine exhaust

outside and away from any building air intakes.

ENGINE HEAT can cause fire.

 Do not locate unit on, over, or near combustible

surfaces or flammables.

 Keep exhaust and exhaust pipes way from

flammables.

EXHAUST SPARKS can cause fire.

 Do not let engine exhaust sparks cause fire.
 Use approved engine exhaust spark arrestor in

required areas – see applicable codes.

1-4. Additional Symbols For Installation, Operation, And Maintenance

FALLING UNIT can cause injury.

 Use lifting eye to lift unit only, NOT running

gear, gas cylinders, trailer, or any other
accessories.

 Use equipment of adequate capacity to lift and

support unit.

 If using lift forks to move unit, be sure forks are long enough to

extend beyond opposite side of unit.

FLYING SPARKS can cause injury.

 Wear a face shield to protect eyes and face.
 Shape tungsten electrode only on grinder with

proper guards in a safe location wearing proper
face, hand, and body protection.

 Sparks can cause fires — keep flammables away.

OVERHEATING can damage motors.

 Turn off or unplug equipment before starting or

stopping engine.

 Do not let low voltage and frequency caused by

low engine speed damage electric motors.

 Do not connect 50 or 60 Hertz motors to the 100 Hertz receptacle

where applicable.

OVERUSE can cause OVERHEATING.

 Allow cooling period; follow rated duty cycle.
 Reduce current or reduce duty cycle before

starting to weld again.

 Do not block or filter airflow to unit.

STATIC (ESD) can damage PC boards.

 Put on grounded wrist strap BEFORE handling

boards or parts.

 Use proper static-proof bags and boxes to

store, move, or ship PC boards.

TILTING OF TRAILER can cause injury.

 Use tongue jack or blocks to support weight.
 Properly install welding generator onto trailer

according to instructions supplied with trailer.

READ INSTRUCTIONS.

 Use only genuine MILLER replacement parts.
 Perform engine maintenance and service

according to this manual and the engine
manual.

OM-4405 Page 3

H.F. RADIATION can cause interference.

ARC WELDING can cause interference.

 High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and
communications equipment.

 Have only qualified persons familiar with

electronic equipment perform this installation.

 The user is responsible for having a qualified electrician prompt-

ly correct any interference problem resulting from the installa­tion.

 If notified by the FCC about interference, stop using the

equipment at once.

 Have the installation regularly checked and maintained.
 Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.

1-5. Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American
Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

Safety and Health Standards, OSHA 29 CFR 1910, from Superinten­dent of Documents, U.S. Government Printing Office, Washington, D.C.

20402.

Recommended Safe Practices for the Preparation for Welding and Cut­ting of Containers That Have Held Hazardous Substances, American

Welding Society Standard AWS F4.1, from American Welding Society,
550 N.W. LeJeune Rd, Miami, FL 33126

National Electrical Code, NFP A Standard 70, from National Fire Protec­tion Association, Batterymarch Park, Quincy, MA 02269.

 Electromagnetic energy can interfere with

sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.

 Be sure all equipment in the welding area is

electromagnetically compatible.

 To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

 Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

 Be sure this welding machine is installed and grounded

according t o this manual.

 If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1235 Jefferson Davis Highway,
Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices For Occupation And Educational Eye And Face
Protection, ANSI Standard Z87.1, from American National Standards
Institute, 1430 Broadway, New York, NY 10018.

Cutting And Welding Processes, NFPA Standard 51B, from National
Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

1-6. EMF Information

Considerations About Welding And The Effects Of Low Frequency
Electric And Ma g netic Fields

Welding current, as it flows through welding cables, will cause electro­magnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to power-
frequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.

To reduce magnetic fields in the workplace, use the following
procedures:

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far away from
operator as practical.

5. Connect work clamp to workpiece as close to the weld as possi­ble.

About Pacemakers:

Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.

OM-4405 Page 4

SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT

UTILISATION

rom _nd_fre 11/98

1-1. Signification des symboles

Signifie Mise en garde ! Soyez vigilant ! Cette procédure
présente des risques de danger ! Ceux-ci sont identifiés
par des symboles adjacents aux directives.

 Identifie un message de sécurité particulier.

 Signifie NOTA ; n’est pas relatif à la sécurité.

1-2. Dangers relatifs au soudage à l’arc

 Les symboles présentés ci-après sont utilisés tout au long du

présent manuel pour attirer votre attention et identifier les ris­ques de danger. Lorsque vous voyez un symbole, soyez
vigilant e t suivez les directives mentionnées afin d’éviter tout
danger. Les consignes de sécurité présentées ci-après ne font
que résumer l’information contenue dans les normes de sécu­rité énumérées à la section 1-5. Veuillez lire et respecter toutes
ces normes de sécurité.

 L’installation, l’utilisation, l’entretien et les réparations ne

doivent être confiés qu’à des personnes qualifiées.

 Au cours de l’utilisation, tenir toute personne à l’écart et plus

particulièrement les enfants.

UN CHOC ÉLECTRIQUE peut tuer.

Un simple contact avec des pièces électriques peut
provoquer une électrocution ou des blessures graves.
L’électrode et le circuit de soudage sont sous tension dès
que l’appareil est sur ON. Le circuit d’entrée et les circuits

moment-là. En soudage semi-automatique ou automatique, le fil, le dévidoir, le
logement des galets d’entraînement et les pièces métalliques en contact avec
le fil de soudage sont sous tension. Des matériels mal installés ou mal mis à la
terre présentent un danger.

 Ne jamais toucher les pièces électriques sous tension.
 Porter des gants et des vêtements de protection secs ne comportant pas

de trous.

 S’isoler de la pièce et de la terre au moyen de tapis ou d’autres moyens iso-

lants suffisamment grands pour empêcher le contact physique éventuel
avec la pièce ou la terre.

 Ne pas se servir de source électrique àcourant électrique dans les zones

humides, dans les endroits confinés ou là où on risque de tomber.

 Se servir d’une source électrique àcourant électrique UNIQUEMENT si le

procédé de soudage le demande.

 Si l’utilisation d’une source électrique àcourant électrique s’avère néces-

saire, se servir de la fonction de télécommande si l’appareil en est équipé.

 Couper l ’alimentation ou arrêter le moteur avant de procéder à l’installation,

à la réparation ou à l’entretien de l’appareil. Déverrouiller l’alimentation
selon la norme OSHA 29 CFR 1910.147 (voir normes de sécurité).

 Installer et mettre à la terre correctement cet appareil conformément à son

manuel d’utilisation et aux codes nationaux, provinciaux et municipaux.

 Toujours vérifier la terre du cordon d’alimentation – Vérifier et s’assurer que

le fil de terre du cordon d’alimentation est bien raccordé à la borne de terre
du sectionneur ou que la fiche du cordon est raccordée à une prise
correctement mise à la terre.

 En effectuant les raccordements d’entrée fixer d’abord le conducteur de

mise à la terre approprié et contre-vérifier les connexions.

 Vérifier fréquemment le cordon d’alimentation pour voir s’il n’est pas en-

dommagé ou dénudé – remplacer le cordon immédiatement s’il est
endommagé – un câble dénudé peut provoquer une électrocution.

 Mettre l’appareil hors tension quand on ne l’utilise pas.
 Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou

mal épissés.

 Ne pas enrouler les câbles autour du corps.
 Si la pièce soudée doit être mise à la terre, le faire directement avec un

câble distinct – ne pas utiliser le connecteur de pièce ou le câble de retour.

 Ne pas toucher l’électrode quand on est en contact avec la pièce, la terre ou

une électrode provenant d’une autre machine.

internes de l’appareil sont également sous tension à ce

Ce groupe de symboles signifie Mise en garde ! Soyez vigilant ! Il y a des
risques de danger reliés aux CHOCS ÉLECTRIQUES, aux PIÈCES EN
MOUVEMENT et aux PIÈCES CHAUDES. Reportez-vous aux symboles
et aux directives ci-dessous afin de connaître les mesures à prendre pour
éviter tout danger.

 N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-le-champ

les pièces endommagées. Entretenir l’appareil conformément à ce
manuel.

 Porter un harnais de sécurité quand on travaille en hauteur.
 Maintenir solidement en place tous les panneaux et capots.
 Fixer le c âble de retour de façon à obtenir un bon contact métal-métal avec

la pièce à souder ou la table de travail, le plus près possible de la soudure.

 Isoler la pince de masse quand pas mis à la pièce pour éviter le contact

avec tout objet métallique.

Une tension DC importante subsiste à l’intérieur
des onduleurs après avoir coupé l’alimentation.

 Couper l’alimentation du poste et décharger les condensateurs d’entrée

comme indiqué dans la Section Maintenance avant de toucher des compo­sants.

LES RAYONS DE L’ARC peuvent pro-
voquer des brûlures dans les yeux et
sur la peau.

Le rayonnement de l’arc du procédé de soudage génère

infrarouges) susceptibles de provoquer des brûlures dans les yeux et sur la
peau. Des étincelles sont projetées pendant le soudage.

 Porter u n casque de soudage muni d’un écran de filtre approprié pour pro-

téger votre visage et vos yeux pendant le soudage ou pour regarder (voir
ANSI Z49.1 et Z87.1 énuméré dans les normes de sécurité).

 Porter des protections approuvés pour les oreilles si le niveau sondre est

trop élevé.

 Utiliser des écrans ou des barrières pour protéger des tiers de l’éclair et de

l’éblouissement; demander aux autres personnes de ne pas regarder l’arc.

 Porter des vêtements de protection constitué dans une matière durable, ré-

sistant au feu (laine ou cuir) et une protection des pieds.

des rayons visibles et invisibles intenses (ultraviolets et

LES FUMÉES ET LES GAZ peuvent
être dangereux.

Le soudage génère des fumées et des gaz. Leur inhalation
peut être dangereux pour votre santé.

 Eloigner votre tête des fumées. Ne pas respirer les fumées.
 À l’interieur, ventiler la zone et/ou utiliser un échappement au niveau de

l’arc pour l’évacuation des fumées et des gaz de soudage.

 Si la ventilation est insuffisante, utiliser un respirateur à alimentation d’air

homologué.

 Lire les spécifications de sécurité des matériaux (MSDSs) et les instruc-

tions du fabricant concernant les métaux, les consommables, les
revêtements, les nettoyants et les dégraisseurs.

 T ravailler dans un espace fermé seulement s’il est bien ventilé ou en por-

tant un respirateur à alimentation d’air. Demander toujours à un surveillant
dûment formé de se tenir à proximité. Des fumées et des gaz de soudage
peuvent déplacer l’air et abaisser le niveau d’oxygène provoquant des
blessures ou des accidents mortels. S’assurer que l’air de respiration ne
présente aucun danger.

 Ne pas souder dans des endroits situés à proximité d’opérations de dé-

graissage, de nettoyage ou de pulvérisation. La chaleur et les rayons de
l’arc peuvent réagir en présence de vapeurs et former des gaz hautement
toxiques et irritants.

 Ne pas souder des métaux munis d’un revêtement, tels que l’acier galvani-

sé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été
enlevé dans la zone de soudure, que l’endroit soit bien ventilé, et si néces­saire, en portant un respirateur à alimentation d’air. Les revêtements et
tous les métaux renfermant ces éléments peuvent dégager des fumées
toxiques en cas de soudage.

OM-4405 Page 5

LE SOUDAGE peut provoquer un in­cendie ou une explosion.

DES PIÈCES CHAUDES peuvent
provoquer des brûlures graves.

Le soudage effectué sur des conteneurs fermés tels que
des réservoirs, tambours ou des conduites peut provoquer

l’arc de soudure. La projection d’étincelles, des pièces chaudes et des
équipements chauds peut provoquer des incendies et des brûlures. Le contact
accidentel de l’électrode avec des objets métalliques peut provoquer des
étincelles, une explosion, un surchauffement ou un incendie. Avant de
commencer le soudage, vérifier et s’assurer que l’endroit ne présente pas de
danger.

 Se protéger et d’autres personnes de la projection d’étincelles et de métal

chaud.

 Ne pas souder dans un endroit là où des étincelles peuvent tomber sur des

substances inflammables.

 Déplacer toutes les substances inflammables à une distance de 10,7 m de

l’arc de soudage. En cas d’impossibilité les recouvrir soigneusement avec
des protections homologués.

 Des étincelles et des matériaux chauds du soudage peuvent facilement

passer dans d’autres zones en traversant de petites fissures et des
ouvertures.

 Surveiller tout déclenchement d’incendie et tenir un extincteur à proximité.
 Le soudage effectué sur un plafond, plancher, paroi ou séparation peut dé-

clencher un incendie de l’autre côté.

 Ne pas effectuer le soudage sur des conteneurs fermés tels que des réser-

voirs, tambours, ou conduites, à moins qu’ils n’aient été préparés
correctement conformément à AWS F4.1 (voir les normes de sécurité).

 Brancher l e c âble sur la pièce le plus près possible de la zone de soudage

pour éviter le transport du courant sur une longue distance par des che­mins inconnus éventuels en provoquant des risques d’électrocution et
d’incendie.

 Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
 En cas de non utilisation, enlever la baguette d’électrode du porte-électro-

de ou couper le fil à la pointe de contact.

 Porter des vêtements de protection dépourvus d’huile tels que des gants

en cuir, une chemise en matériau lourd, des pantalons sans revers, des
chaussures hautes et un couvre chef.

 Avant de souder, retirer toute substance combustible de vos poches telles

qu’un allumeur au butane ou des allumettes.

leur éclatement. Des étincelles peuvent être projetées de

DES PARTICULES VOLANTES
peuvent blesser les yeux.

 Le soudage, l’écaillement, le passage de la pièce

à la brosse en fil de fer, et le meulage génèrent

des étincelles et des particules métalliques vo­lantes. Pendant la période de refroidissement des soudures, elles ris-
quent de projeter du laitier.

 Porter des lunettes de sécurité avec écrans latéraux ou un écran facial.

LES ACCUMULATIONS DE GAZ ris­quent de provoquer des blessures ou
même la mort.

 Fermer l’alimentation du gaz protecteur en cas de

non utilisation.

 Veiller toujours à bien aérer les espaces confinés ou se servir d’un respi-

rateur d’adduction d’air homologué.

 Prévoir u n e p ériode de refroidissement avant d’effec-

tuer des travaux d’entretien.

 Porter des gants et des vêtements de protection pour

travailler sur un moteur chaud.

 Ne pas toucher à mains nues les parties chaudes du moteur ni les pièces

récemment soudées.

LE BRUIT peut affecter l’ouïe.

Le bruit des processus et des équipements peut affecter
l’ouïe.

 Porter des protections approuvés pour les oreilles si

le niveau sondre est trop élevé.

LES CHAMPS MAGNÉTIQUES peuvent
affecter les stimulateurs cardiaques.

 Porteurs d e stimulateur cardiaque, restez à distance.
 Les porteurs d’un stimulateur cardiaque doivent

d’abord consulter leur médecin avant de s’approcher
des opérations de soudage à l’arc, de gougeage ou
de soudage par points.

Si des BOUTEILLES sont endomma­gées, elles pourront exploser.

Des bouteilles de gaz protecteur contiennent du gaz sous
haute pression. Si une bouteille est endommagée, elle peut
exploser. Du fait que les bouteilles de gaz font normale­ment partie du procédé de soudage, les manipuler avec
précaution.

 Protéger les bouteilles de gaz comprimé d’une chaleur excessive, des

chocs mécaniques, du laitier, des flammes ouvertes, des étincelles et des
arcs.

 Placer les bouteilles debout en les fixant dans un support stationnaire ou

dans un porte-bouteilles pour les empêcher de tomber ou de se renverser .

 Tenir les bouteilles éloignées des circuits de soudage ou autres circuits

électriques.

 Ne jamais placer une torche de soudage sur une bouteille à gaz.
 Une électrode de soudage ne doit jamais entrer en contact avec une bou-

teille.

 Ne jamais souder une bouteille pressurisée – risque d’explosion.
 Utiliser seulement des bouteilles de gaz protecteur, régulateurs, tuyaux et

raccords convenables pour cette application spécifique; les maintenir ainsi
que les éléments associés en bon état.

 Ne pas tenir la tête en face de la sortie en ouvrant la soupape de la bouteille.
 Maintenir le chapeau de protection sur la soupape, sauf en cas d’utilisation

ou de branchement de la bouteille.

 Lire et suivre les instructions concernant les bouteilles de gaz comprimé,

les équipements associés et les publication P-1 CGA énumérées dans les
normes de sécurité.

1-3. Dangers existant en relation avec le moteur

LE CARBURANT MOTEUR peut pro­voquer un incendie ou une explosion.

 Arrêter le moteur avant de vérifier le niveau de carbu-

rant ou de faire le plein.

 Ne pas faire le plein en fumant ou proche d’une sour-

ce d’étincelles ou d’une flamme nue.

 Ne pas faire le plein de carburant à ras bord; prévoir de l’espace pour son

expansion.

 Faire attention de ne pas renverser de carburant. Nettoyer tout carbu-

rant renversé avant de faire démarrer le moteur.

 Jeter les chiffons dans un récipient ignifuge.

OM-4405 Page 6

 Toujours vérifier le niveau de liquide de refroidissement dans le vase

 Si le moteur est chaud et que le liquide doit être vérifié, opérer comme

 Mettre des lunettes de sécurité et des gants, placer un torchon sur le

 Dévisser le bouchon légèrement et laisser la vapeur s’échapper avant

LA VAPEUR ET LE LIQUIDE DE
REFROIDISSEMENT CHAUD peuvent
provoquer des brûlures.

 Il est préférable de vérifier le liquide de

refroidissement une fois le moteur refroidi pour éviter
de se brûler.

d’expansion (si présent), et non dans le radiateur (sauf si précisé autre­ment dans la section maintenance du manuel du moteur).

suivant :

bouchon du radiateur.

d’enlever le bouchon.

DES ORGANES MOBILES peuvent
provoquer des blessures.

 Ne pas approcher les mains des ventilateurs, cour-

roies et autres pièces en mouvement.

 Maintenir fermés et fixement en place les portes,

panneaux, recouvrements et dispositifs de

protection.

 Arrêter le moteur avant d’installer ou brancher l’appareil.
 Demander seulement à un personnel qualifié d’enlever les dispositifs de

sécurité ou les recouvrements pour effectuer, s’il y a lieu, des travaux
d’entretien et de d épannage.

 Pour e m p êcher tout démarrage accidentel pendant les travaux d’entre-

tien, débrancher le câble négatif (–) de batterie de la borne.

 Ne pas approcher les mains, cheveux, vêtements lâches et outils des or-

ganes mobiles.

 Remettre en place les panneaux ou les dipositifs de protection et fermer

les portes à la fin des travaux d’entretien et avant de faire démarrer le
moteur.

 Avant d’intervenir, déposer les bougies ou injecteurs pour éviter la mise

en route accidentelle du moteur.

 Bloquer le volant moteur pour éviter sa rotation lors d’une intervention

sur le générateur.

L’EXPLOSION DE LA BATTERIE peut
RENDRE AVEUGLE.

 Toujours porter une protection faciale, des gants en

caoutchouc et vêtements de protection lors d’une in-

tervention sur la batterie.

 Arrêter le moteur avant de débrancher ou de brancher les câbles de

batterie.

 Eviter de provoquer des étincelles avec les outils en travaillant sur la

batterie.

 Ne pas utiliser le poste de soudage pour charger les batteries ou des vé-

hicules de démarrage rapide.

 Observer la polarité correcte (+ et –) sur les batteries.
 Débrancher l e c âble négatif (–) en premier lieu. Le rebrancher en dernier

lieu.

L’ACIDE DE LA BATTERIE peut pro­voquer des br ûlures dans les YEUX et
sur la PEAU.

 Ne pas renverser la batterie.
 Remplacer une batterie endommagée.
 Rincer immédiatement les yeux et la peau à l’eau.

LES GAZ D’ÈCHAPPEMENT DU
MOTEUR peuvent provoquer des
accidents mortels.

 Utiliser l’équipement à l’extérieur dans des zones ou-

vertes et bien ventilées.

 En cas d’utilisation dans un endroit fermé évacuer les gaz d’échappe-

ment du moteur vers l’extérieur à distance des entrées d’air dans les bâti-
ments.

LA CHALEUR DU MOTEUR peut pro­voquer un incendie.

 Ne pas placer l’appareil sur, au-dessus ou à proximité

de surfaces inflammables.

 Tenir à distance les produits inflammables de

l’échappement.

LES ÉTINCELLES À L’ÉCHAPPEMENT
peuvent provoquer un incendie.

 Empêcher les étincelles d’échappement du moteur

de provoquer un incendie.

 Utiliser uniquement un pare-étincelles approuvé –

voir codes en vigueur.

1-4. Dangers supplémentaires en relation avec l’installation, le fonctionnement

et la maintenance

LA CHUTE DE L’APPAREIL peut
blesser.

 Utiliser l’anneau de levage uniquement pour soulever

l’appareil lui-même ; sans chariot, de bouteilles de

gaz, remorque, ou autres accessoires.

 Utiliser un équipement de levage de capacité suffi-

sante pour lever l’appareil.



En utilisant des fourches de levage pour déplacer l’unité, s’assurer
que les fourches sont suffisamment longues pour dépasser du côté
opposé de l’appareil.

LES ÉTINCELLES VOLANTES ris­quent de provoquer des blessures.

 Porter un écran facial pour protéger le visage et les

yeux.

 Affuterr l’électrode au tungstène uniquement à la meuleuse dotée de pro-

tecteurs. Cette manoeuvre est à exécuter dans un endroit sûr lorsque
l’on porte l’équipement homologué de protection du visage, des mains et
du corps.

 Les étincelles risquent de causer un incendie – éloigner toute substance

inflammable.

LE SURCHAUFFEMENT peut endom­mager le moteur électrique.

 Arrêter ou déconnecter l’équipement avant de dé-

marrer ou d’arrêter le moteur.

 Ne pas laisser tourner le moteur trop lentement sous

risque d’endommager le moteur électrique à cause

d’une tension et d’une fréquence trop faibles.

 Ne pas brancher de moteur de 50 ou de 60 Hz à la prise de 100 Hz, s’il y a

lieu.

L’EMPLOI EXCESSIF peut
SURCHAUFFER L’ÉQUIPEMENT.

 Laisser l’équipement refroidir ; respecter l e facteur de

marche nominal.

 Réduire le courant ou le facteur de marche avant de

poursuivre le soudage.

 Ne pas obstruer les passages d’air du poste.

LES CHARGES
ÉLECTROSTATIQUES peuvent
endommager les circuits imprimés.

 Établir la connexion avec la barrette de terre avant de

manipuler des cartes ou des pièces.

 Utiliser des pochettes et des boîtes antistatiques

pour stocker, déplacer ou expédier des cartes de
circuits imprimes.

UNE REMORQUE QUI BASCULE peut
entraîner des blessures.

 Utiliser les supports de la remorque ou des blocs

pour soutenir le poids.

 Installer convenablement le poste sur la remorque

comme indiqué dans le manuel s’y rapportant.

LIRE LES INSTRUCTIONS.

 Utiliser seulement les pièces de rechange d’origine.
 Effecteur la maintenance et la mise en service

d’après le manuel et celui du moteur.

OM-4405 Page 7

LE RAYONNEMENT HAUTE FRÉ-
QUENCE (H.F.) risque de provoquer
des interférences.

 Le rayonnement haute fréquence (H.F.) peut

provoquer des interférences avec les équipements

de radio–navigation et de communication, les

services de sécurité et les ordinateurs.

 Demander seulement à des personnes qualifiées familiarisées avec des

équipements électroniques de faire fonctionner l’installation.

 L’utilisateur est tenu de faire corriger rapidement par un électricien quali-

fié les interférences résultant de l’installation.

 Si le FCC signale des interférences, arrêter immédiatement l’appareil.
 Effectuer régulièrement le contrôle et l’entretien de l’installation.
 Maintenir soigneusement fermés les portes et les panneaux des sources

de haute fréquence, maintenir les éclateurs à une distance correcte et
utiliser une terre et et un blindage pour réduire les interférences
éventuelles.

1-5. Principales normes de sécurité

Safety in Welding and Cutting, norme ANSI Z49.1, de l’American Weld-
ing Society, 550 N.W. Lejeune Rd, Miami FL 33126

Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent
of Documents, U.S. Government Printing Office, Washington, D.C.

20402.

Recommended Safe Practice for the Preparation for Welding and Cut­ting of Containers That Have Held Hazardous Substances, norme A WS

F4.1, de l ’American Welding Society , 550 N.W. Lejeune Rd, Miami FL
33126

National Electrical Code, NFP A Standard 70, de la National Fire Protec­tion Association, Batterymarch Park, Quincy, MA 02269.

LE SOUDAGE À L’ARC risque de
provoquer des interférences.

 L’énergie électromagnétique risque de provoquer

des interférences pour l’équipement électronique
sensible tel que les ordinateurs et l’équipement com­mandé par ordinateur tel que les robots.

 Veiller à ce que tout l’équipement de la zone de soudage soit compatible

électromagnétiquement.

 Pour réduire la possibilité d’interférence, maintenir les câbles de souda-

ge aussi courts que possible, les grouper, et les poser aussi bas que pos­sible (ex. par terre).

 Veiller à souder à une distance de 100 mètres de tout équipement élec-

tronique sensible.

 Veiller à ce que ce poste de soudage soit posé et mis à la terre conformé-

ment à ce mode d’emploi.

 En cas d’interférences après avoir pris les mesures précédentes, il in-

combe à l’utilisateur de prendre des mesures supplémentaires telles que
le déplacement du poste, l’utilisation de câbles blindés, l’utilisation de fil-
tres de ligne ou la pose de protecteurs dans la zone de travail.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
de la Compressed Gas Association, 1235 Jefferson Davis Highway,
Suite 501, Arlington, VA 22202.

Règles de s écurité en soudage, coupage et procédés connexes, norme
CSA W117.2, de l’Association canadienne de normalisation, vente de
normes, 178 Rexdale Boulevard, Rexdale (Ontario) Canada M9W 1R3.

Safe Pra ctices For Occupation And Educational Eye And Face Protec­tion, norme ANSI Z87.1, de l’American National Standards Institute,

1430 Broadway, New York, NY 10018.
Cutting and Welding Processes, norme NFPA 51B, de la National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269.

1-6. Information sur les champs électromagnétiques

Données sur le soudage électrique et sur les ef fets, pour l ’organisme,
des champs magnétiques basse fréquence

Le courant de soudage, pendant son passage dans les câbles de sou­dage, causera des champs électromagnétiques. Il y a eu et il y a encore
un certain souci à propos de tels champs. Cependant, après avoir ex­aminé plus de 500 études qui ont été faites pendant une période de
recherche de 17 ans, un comité spécial ruban bleu du National Re­search Council a conclu: “L’accumulation de preuves, suivant le
jugement du comité, n’a pas démontré que l’exposition aux champs
magnétiques et champs électriques à haute fréquence représente un
risque à la santé humaine”. Toutefois, des études sont toujours en cours
et les preuves continuent à être examinées. En attendant que les con­clusions finales de la recherche soient établies, il vous serait
souhaitable de réduire votre exposition aux champs électromagnéti-
ques pendant le soudage ou le coupage.

Afin de réduire les champs électromagnétiques dans l’environnement
de travail, respecter les consignes suivantes :

1 Garder les câbles ensembles en les torsadant ou en les

attachant avec du ruban adhésif.
2 Mettre tous les câbles du côté opposé de l’opérateur.
3 Ne pas courber pas et ne pas entourer pas les câbles autour de

votre corps.
4 Garder le poste de soudage et les câbles le plus loin possible de

vous.
5 Relier la pince de masse le plus près possible de la zone de

soudure.

Consignes relatives aux stimulateurs cardiaques :

Les personnes qui portent un stimulateur cardiaque doivent avant tout
consulter leur docteur. Si vous êtes déclaré apte par votre docteur, il est
alors recommandé de respecter les consignes ci–dessus.

OM-4405 Page 8

SECTION 2 – DEFINITIONS

2-1. Symbols And Definitions

A

Stop Engine

Air Temperature Or

Engine

Temperature

Engine

Positive Negative

Amperes

V

Electrode

Connection

Stick (SMAW)

Welding

Fast (Run, Weld/

Power)

Battery (Engine)

Check Valve

Clearance

Volts Panel/Local Remote

Work Connection Output

Constant Current

(CC)

Slow (Idle) Start Engine

Engine Oil

Pressure

Fuel

Certified/Trained

Mechanic

MIG (GMAW)

Welding

Engine Oil

Protective Earth

(Ground)

Welding Arc

Alternating

Current

TIG (GTAW)

Time

Hours

h

3

Three Phase

Engine Choke Contactor On

SECTION 3 – SPECIFICATIONS

3-1. Weld, Power, And Engine Specifications

Welding

Mode

CC/DC

CV/DC

(CC/CV

Models

Only)

Weld Output

Range

45 – 500 A

(CC Models)

15 – 500 A

(CC/CV Models)

14 – 40 V

Rated Welding

Output

300 A, 40 Volts DC,

100% Duty Cycle

400 A, 40 Volts DC,

400 A, 40 Volts DC,

60% Duty Cycle

500 A, 30 Volts DC,

40% Duty Cycle

Read Operator’s

Manual

Maximum

Open-

Circuit

Voltage

95

56

Seconds

1

s

Circuit Breaker

50/60 Hz

Hertz

Wis.Con

Wis-Con TM-20

Water-Cooled,

Three-Cylinder,

38 HP Gasoline

Engine

Hz

Auxiliary Power Rating Engine

Standard

Single-Phase,

4 kVA/kW, 34/17 A,

120/240 V AC,

Full kVA Option*

Single-Phase/Three-Phase,

12/15 kVA/kW, 50/36A,

120/240 VAC, 60 Hz

*In Addition To Standard

4 kVA/kW Auxiliary Power

Single Phase

Do Not Switch
While Welding

Fuel

Capacity

25 gal

25 gal
(95 L)

OM-4405 Page 9

3-2. Dimensions, Weights, And Operating Angles

Dimensions

Height

58 in (1473 mm)

(to top of muffler)

G

28-1/2 i n (724 mm)

Width

Depth 64-7/16 i n (1637 mm)

A 64-7/16 in (1637 mm)
B 55-7/8 i n (1419 mm)
C 46-3/8 i n ( 1178)
D 9-1/2 in (241 mm)
E 27-1/2 i n (699 mm)
F 1 in (25 mm)
G 29-1/2 in (743 mm)

H

(mtg. brackets turned in)

30-3/4 in (781 mm)

(mtg. brackets turned out)

9/16 in (14 mm) Dia.

4 Holes

A

B

C

D

D

Weight

No fuel: 1600 lb (726 kg)

w/fuel: 1775 lb (805 kg)

3-3. Volt-Ampere Curves For CC Models

H

Front Panel End

E

E

802 161-A

 Do not exceed tilt angles or engine could

be damaged or unit could tip.

 Do not move or operate unit where it could

tip.

20°
20°

F

30°

30
30°

802 729

°

100

Ranges

80

210 – Max

165 – 350

60

100 – 250

65 – 120
45 – 85

DC VOLTS

40

20

0

0 100 200 300 400 500 600 700

DC AMPERES

The volt-ampere curve shows the
minimum and maximum voltage
and amperage output capabilities of
the welding generator. Curves of al l
other settings fall between the
curves shown.

OM-4405 Page 10

202 666-A

3-4. Volt-Ampere Curves for CC/CV Models

A. Stick Mode

100

Ranges

Max

80

150 – 420
110 – 315

75 – 200

40 – 90

DC VOLTS

60

40

20

0

0 100 200 300 400 500 600 700 800 900

DC AMPERES

B. MIG Mode

100

80

The volt-ampere curves show the
minimum and maximum voltage
and amperage output capabilities of
the welding generator. Curves of al l
other settings fall between the
curves shown.

60

MAX

40

DC VOLTS

20

MIN

0

0 100 200 300 400 500 600 700 800 900 1000

DC AMPERES

C. TIG Mode

100

90
80
70
60

Ranges
50 – 335
40 – 240

25 – 150

15 – 75

50
40

DC VOLTS

30
20
10

0

0 50 100 150 200 250 300 350 400 450 500

DC AMPERES

202 655 / 202 656 / 202 654

OM-4405 Page 11

3-5. Fuel Consumption

2.50

2.25

2.00

1.75

1.50

1.25

1.00

U.S. Gal./Hr.

The curve shows typical fuel use
under weld or power loads.

0.75
IDLE

0.50

0.25

0.00

050

100 150 200 250 300 350 400

DC WELD AM PERES AT 100% DUTY CYCLE

3-6. Duty Cycle And Overheating

100% Duty Cycle At 300 Amperes

Continuous Welding

201 033

Duty Cycle is percentage of 10 mi n ­utes that unit can weld at rated load
without overheating.

 Exceeding duty cycle can

damage unit and void
warranty.

WELD AMPERES

OM-4405 Page 12

% DUTY CYCLE

199 140

3-7. AC Auxiliary Power Curve

300

150

250

125

200

100

150

75

AC VOLTS

100

50

50

25

0

0

0 5 10 15 20 25 30

AC AMPERES IN 240V MODE

0 10 20 30 40 50 60

AC AMPERES IN 120V MODE

3-8. Optional AC Power Plant Curves

The ac power curve shows the aux­iliary power in amperes available at
the 120 and 240 volt receptacles.

193 018

A. 12 kVA/kW Single-Phase Auxiliary Power Plant (No Weld Load)

280

260

240

220

AC VOLTS

200

180

0 20 40 60 80 100

AC AMPERES

B. 15 kVA/kW Three-Phase Auxiliary Power Plant (No Weld Load)

280

260

The ac power curves show the aux­iliary power available in amperes at
the single-phase 120/240 volt re­ceptacle or three-phase 240 volt
terminals.

AC VOLTS

240

220

200

180

0 10203040506070

AC AMPERES

198 868 /98 869

OM-4405 Page 13

SECTION 4 – INSTALLATION

4-1. Installing Welding Generator (See Sections 4-2 And 4-3)

Movement Airflow Clearance Location

18 in

OR

18 in

(460 mm)

18 in

(460 mm)

(460 mm)

(460 mm)

18 in

(460 mm)

18 in

OR

Grounding

1

2

4-2. Using Lifting Eye

GND/PE

OR

Electrically bond generator frame to
vehicle frame by metal-to-metal
contact.

 Always securely fasten

welding generator onto
transport vehicle or trailer
and comply with all DOT and

3

3

4

2

install2 1/01 – Ref. 800 652 / Ref. 800 477-A / 158 936-A / 0854

1

2

other applicable codes.

 Always ground generator

frame t o vehicle frame to pre­vent electric shock and static
electricity hazards.

1 Generator Base
2 Metal Vehicle Frame
3 Equipment Grounding

Terminal
4 Grounding Cable
Use #10 AWG or larger insulated

copper wire.

 If unit does not have GFCI re-

ceptacles, use GFCI-

protected extension cord.

1 Lifting Eye
2 Nut
3 Carriage Bolt
Raise lifting eye until it snaps in

place. Lower lifting eye when not
needed.

 To lock the lifting eye in the up-

right position, insert a 3/8-16 x

1-1/2 in carriage bolt through

slot in bracket and secure with

nut (bolt and nut not supplied).

Tools Needed:

OM-4405 Page 14

Ref. 802 729

4-3. Mounting Welding Generator

1

Welding Unit In Place

Bolting Unit In Place

1

 Do not weld on base. Weld-

ing on base can cause fuel
tank fire or explosion. Weld
only on the four mounting
brackets or bolt unit down.

1 Mounting Bracket
2 1/2 in Bolt And Washer (Not

Supplied)

3 3/8-16 x 1 in Screws

(Supplied)

To Bolt Unit In Place:

Remove hardware securing the
four mounting brackets t o the base.
Reverse brackets and reattach to
base with original hardware.

2

Mount unit to truck or trailer with 1/2
in (12 mm) hardware (not supplied).

To Weld Unit In Place:

Weld unit to truck or trailer only at
the four mounting brackets.

Tools Needed:

9/16 in

4-4. Installing Exhaust Pipe

3

Ref. 190 250-A / Ref. 802 730

 Stop engine and let cool.
 Engine backfire can cause se-

vere burns or other injuries. D o
not point exhaust pipe toward
control pa n el. Keep away from
exhaust outlet.

 Point exhaust pipe in desired di-

rection but always away from
front panel and direction of travel.

Tools Needed:

1/2 in

Ref. 802 730 / Ref. 201 841

OM-4405 Page 15

4-5. Activating The Dry Charge Battery (If Applicable)

5

4

1

3

2

Remove battery from unit.
1 Eye Protection – Safety

Glasses Or Face Shield
2 Rubber Gloves
3 Vent Caps
4 Sulfuric Acid Electrolyte

(1.265 Specific Gravity)
5 Well
Fill each cell with electrolyte to

bottom of well (maximum).

 Do not overfill battery cells.

Wait ten minutes and check electro­lyte level. If necessary , add electro­lyte to raise to proper level. Reins­tall vent caps.

6 Battery Charger

 Read and follow all instruc-

tions supplied with battery

charger.

Charge battery for 12 minutes at 30
amperes or 30 minutes at 5 am­peres. Disconnect charging cables
and install battery.

 When electrolyte is low, add

only distilled water to cells to

maintain proper level.

5 A For 30 Minutes

30 A For 12 Minutes

OM-4405 Page 16

OR

6

Tools Needed:

+

–

rubber gloves

glasses

drybatt1 1/98 – 0886

4-6. Connecting The Battery

 Connect Negative (–) Cable Last.

Tools Needed:

1/2 in

+

–

802 168-B / Ref. 201 841 / 802 313 / S-0756-C

Notes

OM-4405 Page 17

4-7. Engine Prestart Checks

Full

Gasoline

Check radiator coolant level when

fluid is low in recovery tank.

Full

Capacity: 9 qt (8.5L)

Full

 Check all engine fluids daily.

Engine must be cold and on a level surface.
Unit is shipped with 20W break-in oil.

Automatic shutdown system stops engine if
oil pressure is too low, or coolant tempera­ture is too high.

 This unit has a low oil pressure shut-

down switch. However, some condi­tions may cause engine damage before
the engine shuts down. Check oil level
often and do not use the oil pressure
shutdown system to monitor oil level.

Follow run-in procedure in engine manual.

Fuel

Add fresh fuel before starting engine the first

time (see engine maintenance label for fuel
specifications).

Oil

After fueling, check oil with unit on level sur­face. If oil is not up to full mark on dipstick,
add oil (see maintenance label).

Coolant

Check coolant level in radiator before start­ing unit the first time. If necessary, add cool­ant to radiator until coolant level is at bottom
of filler neck.

Check coolant level in recovery tank daily.
If necessary, add coolant to recovery tank
until coolant level is between Cold Full a n d
Hot Full levels. If recovery tank coolant level
was low, also check coolant level in radiator.
Add coolant if level is below bottom of radia­tor filler neck.

Coolant Recovery Tank

Hot Full

Cold Full

802 731

Engine coolant is a mixture of water and
ethylene glycol base antifreeze. Add anti­freeze to mixture if using the unit in tempera-

tures below –34° F (–37° C).
Keep radiator and air intake clean and free

of dirt.

 Incorrect engine temperature can

damage engine. Do not run engine
without a properly working thermo­stat and radiator cap.

 To improve cold weather starting:

Keep battery in good condition. Store
battery in warm area off concrete sur­face.

Use correct grade oil for cold weather
(see Section 8-1).

OM-4405 Page 18

4-8. Connecting To Weld Output Terminals

Tools Needed:

1

2

4-9. Selecting Weld Cable Sizes

3/4 in

 Stop engine.

1 Positive (+) Weld Output Terminal
2 Negative (–) Weld Output Terminal
For Stick and TIG welding Direct Current

Electrode Positive (DCEP), connect
electrode holder cable to Positive (+) ter­minal o n left and work cable to Negative
(–) terminal on right.

For Direct Current Electrode Negative
(DCEN), reverse cable connections.

If equipped with optional polarity switch,
connect electrode holder cable to Elec­trode terminal on left and work cable to
Work terminal on right.

For MIG and FCAW welding Direct Cur­rent Electrode Positive (DCEP) on CC/
CV models, connect wire feeder cable to
Positive (+) terminal on left and work
cable to Negative (–) terminal on right.
Use Process/Contactor switch to select
type of weld output (see Section 6-3).

For Direct Current Electrode Negative
(DCEN), reverse cable connections.

If equipped with optional polarity switch,
connect wire feeder cable to Electrode
terminal on left and work cable to Work
terminal on right.

802 729

Weld Output

Terminals

 Stop engine before

connecting t o weld out­put terminals.

 Do not use worn, dam-

aged, undersized, or
poorly spliced cables.

Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit

Not Exceeding***

100 ft (30 m) or Less

Welding

Amperes

100 4 (20) 4 (20) 4 (20) 3 (30) 2 (35) 1 (50) 1/0 (60) 1/0 (60)
150 3 (30) 3 (30) 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 3/0 (95)
200 3 (30) 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120) 4/0 (120)

250 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120)

300 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120)

350 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120)

400 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120)

10 – 60%

Duty

Cycle

60 – 100%

Duty

Cycle

150 ft

(45 m)

200 ft

(60 m)

250 ft

(70 m)

10 – 100% Duty Cycle

2 ea. 2/0

(2x70)

2 ea. 2/0

(2x70)

300 ft

(90 m)

2 ea. 2/0

(2x70)

2 ea. 3/0

(2x95)

2 ea. 3/0

(2x95)

350 ft

(105 m)

2 ea. 2/0

(2x70)

2 ea. 3/0

(2x95)

2 ea. 3/0

(2x95)

2 ea. 4/0

(2x120)

400 ft

(120 m)

2 ea. 2/0

(2x70)

2 ea. 3/0

(2x95)

2 ea. 4/0

(2x120)

2 ea. 4/0

(2x120)

500 2/0 (70) 3/0 (95) 4/0 (120)

* This chart is a general guideline and may not suit all applications. If cable overheating occurs (normally you can smell it), use next size larger

cable.
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.

( ) = mm2 for metric use S-0007-E–
***For distances longer than those shown in this guide, call a factory applications representative at 920-735-4505.

2 ea. 2/0

(2x70)

2 ea. 3/0

(2x95)

2 ea. 4/0

(2x120)

3 ea. 3/0

(3x95)

OM-4405 Page 19

3 ea. 3/0

(3x95)

4-10. Connecting To Remote Amperage Adjust Receptacle RC13 On CC Models

1 Remote Amperage Adjust

Receptacle RC13
Connect optional remote control to

RC13 (see Section 5-3).

1

Ref. 154 862-A / 048 720-K / 802 729

OM-4405 Page 20

4-11. Connecting To Remote 14 Receptacle RC14 On CC/CV Models

Socket* Socket Information

A 24 volts ac. Protected by circuit

24 VOLTS AC

24 VOLTS AC

B Contact closure to A completes

C Output t o remote control:+10

New! LDR-14 long

distance remote

(includes 120 V

receptacle)

receptacle)

D Remote control circuit common.

REMOTE

OUTPUT

CONTROL

OR

E DC input command signal: 0 to

breaker CB5.

24 volt ac contactor control
circuit.

volts dc in MIG or Stick mode;
0 to +10 volts dc in TIG mode.

+10 volts from min. to max. of
remote control with Voltage/
Amperage Adjust control at
max.

*The remaining sockets are not used.

802 729

K Chassis common.

GND

NEUTRAL G Circuit common for 24 volt ac

circuit.

OM-4405 Page 21

SECTION 5 – OPERATING WELDING GENERATOR – CC MODELS

5-1. Front Panel Controls For CC Models (See Section 5-2)

65

13 18 1914 1210 11

47

9

8

2

OM-4405 Page 22

17

15 16

3

1

201 841 / 802 729

5-2. Description Of Front Panel Controls For CC Models (See Section 5-1)

Engine Starting Controls

1 Magnetic Shutdown Switch
Use switch during start-up to bypass engine

shutdown system. System stops engine if oil
pressure is too low or coolant temperature is
too high.

2 Starting Aid (Engine Choke Control)
Use control to change engine air-fuel mix.
3 Engine Control Switch
Use switch to start engine, select engine

speed, and stop engine.
In Run position, engine runs at weld/power

speed. In Run/Idle position, engine runs at
idle speed at no load and weld speed with load
applied.

To Start:

 If engine does not start, let engine come

to a complete stop before attempting re­start.

Pull Choke control out. Turn Engine Control
switch to Start while pressing Shutdown
switch. Release Engine Control switch when
engine starts. Continue holding Shutdown
switch until engine indicator lights go out.
Push Choke control in.

To Stop: turn Engine Control switch to Off
position.

Engine Indicator Lights

4 Battery Charging Light
Light goes on if engine alternator is not charg-

ing battery. Engine continues to run.

 Stop engine and fix trouble if Battery

Charging light goes on.

5 Engine Temperature Light
Light goes on and engine stops if engine tem-

perature is above 230 ° F (110° C).

 Stop engine and fix trouble if Engine

Temperature light goes on.

6 Engine Oil Pressure Light
Light goes on and engine stops if oil pressure

is below 5 psi (34 kPa). Light goes on momen­tarily during start-up but goes out when en­gine reaches normal oil pressure.

 Stop engine and fix trouble if Engine

Oil Pressure light stays on after start­up.

7 Fuel Light
Fuel light is not active on this model.

8 Engine Hour Meter

Engine Gauges

 To read gauges and engine indicator

lights with engine off, turn Engine Control
switch to Run/Idle and press Magnetic
Shutdown switch (see Section 8-10).

9 Fuel Gauge
Use gauge to check fuel level.
To check fuel level when engine is not run-

ning, turn Engine Control switch to Run/Idle
position and press Magnetic Shutdown
switch.

10 Battery Voltmeter (Optional)
Use gauge to check battery voltage and moni-

tor the engine charging system. The meter
should read about 14 volts dc when the en­gine is running, and about 12 volts dc when
the engine is stopped.

11 Engine Coolant Temperature Gauge

(Optional)

Normal temperature is 180 - 203° F (82 - 95°
C). When equipped with gauge option, engine
stops if temperature exceeds 220° F (104° C).

12 Engine Oil Pressure Gauge (Optional)
Normal pressure is 30 – 80 psi (207 – 552

kPa). When equipped with gauge option, en­gine stops if pressure is below 10 psi (69
kPa).

Weld Controls

 Max OCV Control Circuit: This unit has

a max OCV control circuit that resets Am­perage Adjust control R1 to maximum
when the arc breaks. When an arc is
struck, weld outpu t c o n t r o l returns to the
R1 front panel or combination front panel/
remote control setting. The Amperage
Adjust control adjusts amperage only
when welding and does not adjust open­circuit voltage.

The max OCV circuit is disabled when
the Stick/TIG Selection switch is in
Scratch Start TIG position (see item 15).

13 Ampere Range Switch

 Do not switch under load.

Use switch to select weld amperage range.
For most welding applications, use lowest

amperage range possible to help prevent arc
outages.

14 Amperage Adjust Control
Control adjusts amperage within range se-

lected by Ampere Range switch. Weld output
would be about 153 A DC with controls set as
shown (50% of 100 to 205 A).

 The numbers around the control are for

reference only and do not represent an
actual percentage value.

15 Stick/TIG Selection Switch
Use switch to disable the max OCV circuit

and the arc drive (dig) circuit for scratch start
TIG welding (see max OCV note under Weld
Controls).

When switch is in the Stick position, the max
OCV circuit resets Amperage Adjust Control
R1 to maximum when the arc breaks.

Also in the Stick position, the arc drive (dig)
circuit provides additional amperage during
low voltage (short arc length conditions) to
prevent “sticking” electrodes.

When switch is in Scratch Start TIG position,
the max OCV and arc drive (dig) circuits are
disabled and OCV changes when the control
is adjusted.

16 Amperage Adjust Switch And Remote

Amperage Adjust Receptacle

Connect optional remote control to RC13
(See Section 4-10). Use switch to select front
panel or remote amperage control. For re­mote control, place switch in Remote position
and connect remote control to Remote Am­perage Adjust receptacle RC13 (see Sec­tions 4-10 and 5-3).

17 Polarity Switch (Optional)

 Do not switch under load.

Use switch to change weld output. Select ei­ther DC Electrode Positive (DCEP) or DC
Electrode Negative (DCEN).

Weld Meters

18 DC Voltmeter (Optional)
Voltmeter displays voltage at the weld output

terminals, but not necessarily the welding arc
due to resistance of cable and connections.

19 DC Ammeter (Optional)
Ammeter displays amperage output of the

unit.

OM-4405 Page 23

5-3. Remote Amperage Control On CC Models (Optional)

1

1 Remote Amperage Adjust

Receptacle RC13
Connect optional remote control to

RC13 (see Section 4-10).

Example: Combination Remote Amperage Control (Stick)

In Example:

Range = 100 to 205 A DC

Percentage Of Range = 50%

Max = About 153 A DC (50% of 100 to 205)

Max (153 A DC)

Min (75 A DC)

Adjust Optional Remote ControlSet Switches Set Range Set Control

0774 / Ref. 154 862-A / Ref. 181 711-A / 802 729

OM-4405 Page 24

Notes

OM-4405 Page 25

SECTION 6 – OPERATING WELDING GENERATOR – CC/CV MODELS

6-1. Front Panel Controls For CC/CV Models (See Section 6-2)

65

14 18 1915 1210 11

47

9

8

2

OM-4405 Page 26

17

13 16

3

1

201 579 / 802 729

6-2. Description Of Front Panel Controls For CC/CV Models (See Section 6-1)

Engine Starting Controls

1 Magnetic Shutdown Switch
Use switch during start-up to bypass engine

shutdown system. System stops engine if oil
pressure is too low or engine temperature is
too high.

2 Starting Aid (Engine Choke Control)
Use control to change engine air-fuel mix.
3 Engine Control Switch
Use switch to start engine, select engine

speed, and stop engine.
In Run position, engine runs at weld/power

speed. In Run/Idle position, engine runs at
idle speed at no load and weld speed with load
applied.

To Start:

 If engine does not start, let engine come

to a complete stop before attempting re­start.

Pull Choke control out. Turn Engine Control
switch to Start while pressing Shutdown
switch. Release Engine Control switch when
engine starts. Continue holding Shutdown
switch until engine indicator lights go out.
Push Choke control in.

To Stop: turn Engine Control switch to Off
position.

Engine Indicator Lights

4 Battery Charging Light
Light goes on if engine alternator is not charg-

ing battery. Engine continues to run.

 Stop engine and fix trouble if Battery

Charging light goes on.

5 Engine Temperature Light
Light goes on and engine stops if engine tem-

perature is above 230 ° F (110° C).

 Stop engine and fix trouble if Engine

Temperature light goes on.

6 Engine Oil Pressure Light
Light goes on and engine stops if oil pressure

is below 5 psi (34 kPa). Light goes on momen-

tarily during start-up but goes out when en­gine reaches normal oil pressure.

 Stop engine and fix trouble if Engine

Oil Pressure light stays on after start­up.

7 Fuel Light
Fuel light is not active on this model.
8 Engine Hour Meter

Engine Gauges

 To read gauges and engine indicator

lights with engine off, turn Engine Control
switch to Run/Idle and press Magnetic
Shutdown switch (see Section 8-10).

9 Fuel Gauge
Use gauge to check fuel level.
To check fuel level when engine is not run-

ning, turn Engine Control switch to Run/Idle
position and press Magnetic Shutdown
switch.

10 Battery Voltmeter (Optional)
Use gauge to check battery voltage and moni-

tor the engine charging system. The meter
should read about 14 volts dc when the en­gine is running, and about 12 volts dc when
the engine is stopped.

11 Engine Coolant Temperature Gauge

(Optional)

Normal temperature is 180 - 203° F (82 - 95°
C). When equipped with gauge option, engine
stops if temperature exceeds 220° F (104° C).

12 Engine Oil Pressure Gauge (Optional)
Normal pressure is 30 – 80 psi (207 – 552

kPa). When equipped with gauge option, en­gine stops if pressure is below 10 psi (69
kPa).

Weld Controls

13 Process/Contactor Switch
See Section 6-3 for Process/Contactor

switch information.
14 Ampere Range Switch

 Do not switch under load.

Use switch to select weld amperage range.

Use the lowest four ranges for Stick and TIG
welding. Read the upper set of numbers at
each range for Stick welding and the lower set
at each range for TIG welding.

Use the highest range for MIG welding and for
cutting and gouging (CAC-A).

For most welding applications, use lowest
amperage range possible to help prevent arc
outages.

15 Voltage/Amperage Adjust Control
With Process/Contactor switch in any Stick or

TIG setting, use control to adjust amperage
within range selected by Ampere Range
switch. With Process/Contactor switch in any
MIG position, use control to adjust voltage.
With Voltage/Amperage Adjust Switch in Re­mote position, control limits the remote am­perage i n TIG mode, but has no ef fect in Stick
and MIG modes.

Weld output would be about 213 A DC with
controls set as shown (50% of 110 to 315 A).

 The numbers around the control are for

reference only and do not represent an
actual percentage value.

16 Voltage/Amperage Adjust Switch And

Remote 14 Receptacle

Use switch to select front panel or remote
voltage/amperage control. For remote con­trol, place switch in Remote position and con­nect remote control to Remote 14 receptacle
RC14 (see Sections 4-11 and 6-4).

17 Polarity Switch (Optional)

 Do not switch under load.

Use switch to change weld output. Select ei­ther DC Electrode Positive (DCEP) or DC
Electrode Negative (DCEN).

Weld Meters

18 DC Voltmeter (Optional)
Voltmeter displays voltage at the weld output

terminals, but not necessarily the welding arc
due to resistance of cable and connections.

19 DC Ammeter (Optional)
Ammeter displays amperage output of the

unit.

OM-4405 Page 27

6-3. Process/Contactor Switch On CC/CV Models

1 Process/Contactor Switch

 Weld output terminals are en-

1

ergized when Process/Con­tactor switch is in an Electrode
Hot position and the engine is
running.

Use switch to select weld process
and weld output on/off control (see
table below and Section 6-4).

Place switch in Remote positions to
turn weld output on and of f with a de­vice connected to the remote 14 re­ceptacle.

Place switch in Electrode Hot posi­tions for weld output to be on whenev­er the engine is running.

Use Stick position for air carbon arc
(CAC-A) cutting and gouging.

When switch is in a Stick position, the
arc drive (dig) circuit provides addi­tional amperage during low voltage
(short arc length conditions) to pre­vent “sticking” electrodes.

The arc drive (dig) circuit is disabled
when switch is in MIG or TIG
positions.

 Place switch in Electrode Hot -

Stick position when using option­al auxiliary power plant (see Sec­tion 7-2).

 The engine auto idle function

does not work in the Remote-TIG
mode.

Process/Contactor Switch Settings

Switch Setting Process Output On/Off Control Engine Auto Idle

Remote – TIG

Remote – Stick Stick (SMAW) With Remote On/Off At Remote 14 Receptacle Active

Remote – MIG MIG (GMAW) At Remote 14 Receptacle Active

Electrode Hot – MIG MIG (GMAW) Electrode Hot Active

Electrode Hot – Stick

Electrode Hot – Scratch

Start TIG

GTA W With HF Unit, Pulsing

Device, Or Remote Control

Stick (SMAW),

Air Carbon Arc (CAC-A) Cutting

And Gouging

Scratch Start TIG (GTAW) Electrode Hot Active

At Remote 14 Receptacle Not Active

Electrode Hot Active

OM-4405 Page 28

6-4. Remote Voltage/Amperage Control On CC/CV Models (Optional)

1 Remote 14 Receptacle RC14
Connect optional remote control to

RC14 (see Section 4-11).

1

Example: Combination Remote Amperage Control (Stick)

Set V/A

Adjust Switch

Example: Combination Remote Amperage Control (TIG)

Set Remote

Process

Set Range Control Not

Used In Remote

Stick Mode

Process = Stick (Using Remote On/Off)

In Example:

Range = 110 to 315 A DC

Min = 110 A DC

Max = 315 A DC

Max (315 A DC)

Min (110 A DC)

Adjust Optional Remote Control

In Example:

Process = TIG (Using Remote On/Off)

Range = 40 to 240 A DC

Percentage Of Range = 50%

Min = 40 A DC

Max = About 140 A DC (50% of 40 to 240)

Set V/A

Adjust Switch

Set Remote

Process

Set Range Set Control

Max (140 A DC)

Min (40 A DC)

Adjust Optional Remote Control

0774 / Ref. 201 579 / 802 730

OM-4405 Page 29

SECTION 7 – OPERATING AUXILIARY EQUIPMENT

7-1. 120 Volt And 240 Volt Receptacles

1

3

4

1 120 V 20 A AC GFCI

Receptacle GFCI1

2 240 V 30 A AC Twistlock

Receptacle RC1

Receptacles supply 60 Hz single­phase power at weld/power speed.

If a ground fault is detected, GFCI

2

Reset button pops out and
receptacle does not work. Check
for faulty tools plugged in
receptacle. Press button to reset
GFCI1.

 At least once a month, run en-

gine at weld/power speed and
press test button to verify GFCI
is working properly.

3 Circuit Breaker CB1
4 Circuit Breaker CB2
CB1 protects RC1 and the genera-

tor winding from overload. If CB1
opens, RC1 and GFCI1 do not
work. Place switch in On position to
reset breaker .

CB2 protects GFCI1 from overload.
If CB2 opens, GFCI1 does not
work. Press button to reset breaker .

 If a circuit breaker continues to

open, contact Factory Autho­rized Service Agent.

 Auxiliary power is not affected

by weld output.

Maximum output is 2.4 kVA/kW
from GFCI1 and 4 kVA/kW from
RC1. Maximum output from all re­ceptacles is 4 kVA/kW.

EXAMPLE: If 13 A is drawn from
RC1, only 7 A is available at GFCI1:

(240 V x 13 A) + (120 V x 7 A) =

4.0 kVA/kW

OM-4405 Page 30

191 624-A

7-2. Connecting To Optional Auxiliary Power Plant (CC/CV Models Only)

 Place Process/Contactor switch

in Electrode Hot - Stick position
when using auxiliary power plant

Single-Phase Power Connection

Three-Phase Power Connection

Remove plug
before inserting
leads. Reinstall
bushing.

5

6

7

9

8

12

 Close panel opening

if no connections are
made to power plant.

Rear Of Panel

91 92 93

240V

120V

120V

240V

240V

1-Phase

240V

3-Phase

AC

Output

Volts

Amps

KVA/KW

Engine Speed 1850 RPM

Lead 42 connects to GROUND stud on
front of unit.

Jumper 42 i s connected to 90 at factory.

Single
Phase

1

120/240

50
12

Three

Phase

3

240

48
20

60 HzFrequency

4

3

2
12

10

11

 Close panel

opening if no
connections
are made to
power plant.

Tools Needed:

93
91

90

92

(see Section 6-3).

Single-Phase Auxiliary Power

1 120/240 V 50 A Receptacle

RC5

RC5 is connected to the optional
auxiliary power plant and supplies 60
Hz single-phase power at weld/pow­er speed. Maximum output from RC5
is 12 kVA/kW. Power available at
RC5 is reduced when welding.

2 Circuit Breaker CB7
Circuit breaker CB7 protects single-

phase receptacle RC5 and the load
wires from overload. If CB7 opens, all
auxiliary power plant output stops
and the receptacle does not work.

Three-Phase Auxiliary Power

 Stop engine.
 Power and weld outputs are

live at the same time. Discon­nect or insulate unused
cables.

 Have qualified person install ac-

cording to circuit diagram and
Auxiliary Power Guidelines (see
Section 10).

Remove auxiliary power panel
mounting screws. Tilt panel forward.

3 Lead 93
4 Lead 92
5 Lead 91
6 Lead 42 (Circuit Grounding

Lead)
7 Lead 90 (Neutral)
8 Isolated Neutral Terminal
9 Jumper Lead 42
10 Grounding Terminal
Jumper 42 i s connected to lead 90 a t

factory. Jumper 42 may be discon­nected from neutral to meet applica­ble electrical codes.

Lead 42 connects to front panel
Ground stud.

11 User-Supplied Leads
12 Circuit Breaker CB7 User

Terminals
Connect user-supplied leads to ter-

minals on CB7 and to the isolated
neutral terminal and grounding termi­nal as necessary.

 Circuit breaker CB7 protects

single-phase receptacle RC5

and the load wires from overload.

If CB7 opens, all auxiliary power

plant output stops and the recep-

tacle does not work.

Reinstall auxiliary power panel.

Ref. 197 399 / 802 332-E

OM-4405 Page 31

7-3. Optional Auxiliary Power Receptacles

European Receptacle

5

6

Australian Receptacle

5

6

South African Receptacle

5

6

1

1 120 V 20 A AC GFCI

Receptacle GFCI1

2 240 V 16 A AC European

Receptacle RC1

2

3 240 V 15 A AC Australian

Receptacle RC1

4 240 V 15 A AC South African

Receptacle RC1

Receptacles supply 60 Hz single­phase power at weld/power speed.

If a ground fault is detected, the
GFCI Reset button pops out and
the receptacle does not work.
Check for faulty tools plugged in
receptacle. Press button to reset
GFCI1.

 At least once a month, run en-

gine at weld/power speed and
press test button to verify GFCI
is working properly.

31

5 Circuit Breaker CB2
6 Circuit Breaker CB3
CB2 protects GFCI1 from overload.

If CB2 opens, GFCI1 does not
work. Place button to reset breaker .

CB3 protects RC1 from overload. If
CB3 opens, RC1 does not work.
Press button to reset breaker.

 If a circuit breaker continues to

open, contact Factory Autho­rized Service Agent.

 Auxiliary power is not affected

by weld output.

Maximum output is 2.4 kVA/kW

41

from GFCI1 and 4 kVA/kW from
RC1. Maximum output from all re­ceptacles is 4 kVA/kW.

EXAMPLE: If 13 A is drawn from
RC1, only 7 A is available at GFCI1:

(240 V x 13 A) + (120 V x 7 A) =

4.0 kVA/kW

OM-4405 Page 32

191 624

SECTION 8 – MAINTENANCE & TROUBLESHOOTING

8-1. Maintenance Label

OM-4405 Page 33

8-2. Routine Maintenance

Note

Coolant

Full

Clean Air Filter.

See Section 8-4.

Follow the storage procedure in the engine owner’s manual if the unit will not be used for an
extended period.

 Stop engine before maintaining.

Recycle engine

fluids.

 See also Engine Manual and Mainte-

nance Label. Service unit more often if
used in severe conditions.

* To be done by Factory Authorized

Service Agent.

8 h

OIL
Full

Check Fluid
Levels. See

Section 4-7.

Wipe

Up

Spills.

50 h

1/2 in.

(13 mm)

Check Belt

Tension.

Clean And

Tighten

Weld

Terminals.

Change Oil. See

Section 8-8.

Replace fuel

filter. See

Section 8-8.

Check

Spark
Plugs.

100 h

Change Oil

Filter. See

Section 8-8.

Clean And

Tighten
Battery

Connections.

Check air cleaner hoses
for cracks and loose
clamps.

250 h

Check And

Clean Spark

Arrestor. See

Section 8-3.

OM-4405 Page 34

Replace

Unreadable

Labels.

500 h

Check

Valve

Clearance.*

1000 h

Blow Out Or

OR

Vacuum Inside.

During Heavy

Service,

Clean Monthly.

SLUDGE

Service Welding Generator

Brushes And Slip Rings. Service

More Often In Dirty Conditions.*

8-3. Inspecting And Cleaning Optional Spark Arrestor Muffler

3
2

1

Repair Or

Replace

Damaged

Cables.

FUEL

 Stop engine and let cool.

1 Spark Arrestor Muffler
2 Cleanout Plug
Remove plug and remove any dirt

covering cleanout hole.
3 Exhaust Pipe
Start engine and run at idle speed to

blow out cleanout hole. If nothing
blows out of hole, briefly cover end
of exhaust pipe with fireproof
material.

 Stop engine and let cool.

Reinstall cleanout plug.

Drain Sludge

From Fuel
Tank. See

Section 8-8.

Tools Needed:

3/8 in

802 729 / Ref. 201 841

OM-4405 Page 35

8-4. Servicing Air Cleaner

Keep nozzle
2 in (51 mm)

from element.

Blow Inspect

 Stop engine.
 Do not run engine without air

2

41 3

cleaner or with dirty element. E n­gine damage caused by using a
damaged element is not covered
by the warranty.

 The air cleaner primary element can

be cleaned but the dirt holding capac­ity of the filter is reduced with each
cleaning. The chance of dirt reaching
the clean side of the filter while clean­ing and the possibility of filter damage
makes cleaning a risk. Consider the
risk of unwarrantable equipment

5

damage when determining whether
to clean or replace the primary ele­ment.

If you decide to clean the primary ele­ment, we strongly recommend instal­ling an optional safety element to pro­vide additional engine protection.
Never clean a safety element. Re­place the safety element after servic­ing the primary element three times.

Clean or replace primary element if dirty
(see note above before cleaning). Re-
place primary element if damaged. Re­place primary element yearly or after six
cleanings.

1 Housing
2 Safety Element (Optional)
3 Primary Element
4 Dust Cap
5 Dust Ejector

To clean air filter:

Wipe off cap and housing. Remove cap
and dump out dust. Remove element(s).
Wipe dust from inside cap and housing
with damp cloth. Reinstall safety element
(if present). Reinstall cap.

 Do not clean housing with air

hose.

Clean primary element with compressed
air only.

Air pressure must not exceed 100 psi
(690 kPa). Use 1/8 in (3 mm) nozzle and
keep nozzle at least 2 in (51 mm) from
inside of element. Replace primary ele­ment if i t has holes or damaged gaskets.

Reinstall primary element and cap (dust
ejector down).

OM-4405 Page 36

aircleaner1 9/00 – 153 929-B / 153 585 / Ref. S-0698-B

8-5. Adjusting Engine Weld/Power Speed

Engine Speed

(No Load)

Weld/Power

8

3
2

7

1/16 in

(1.6 mm)

1

RPM (Hz)

1850 (61.7)

3-1/4 in

(83 mm)

12

Maximum

6

4

5

13

 Stop engine and let cool.

 Governor sensitivity may re-

quire adjustment if engine
speed is adjusted (see Section
8-7).

Engine speed is factory set and
should not require adjustment. Af­ter tuning engine, check engine
speed with tachometer or frequen­cy meter. See table for proper no
load speed. If necessary, adjust
speed as follows:

Start engine and run until warm.

1011

9

On CC Models, place Stick/TIG
switch in Stick position.

On CC/CV models, turn Process/
Contactor switch to Stick – Elec­trode Hot position.

1 Socket Nut
2 Governor Linkage Rod
3 Lock Nut
4 Socket
5 Governor Arm
Rod length should be 3-1/4 in (83

mm) between lock nuts. To adjust,
remove socket from arm and loos­en lock nut. Turn socket to adjust
length. Tighten nut and reattach
socket to arm.

 If linkage binds, loosen socket

nuts and t u r n s o c k e t s u n t i l l i n k ­age works smoothly. Tighten
nuts.

6 Carburetor
7 Throttle Stop Plate
8 Throttle Stop
Clearance between plate and stop

should be 1/16 in (1.6 mm). To ad­just clearance, proceed as follows:

9 Linkage Pivot Arm
10 Linkage Socket
11 Lock Nut
Remove socket at arm and loosen

lock nut. Turn socket to adjust
clearance. Reattach socket and
tighten nut.

Start engine and run until warm.
Turn Engine Control switch to Run
position.

12 Governor Speed Screw
13 Lock Nut
Loosen nut. Turn screw until engine

runs at weld/power speed.

 Stop engine.

Close door.

Tools Needed:

3/8, 7/16 in

802 731 / 802 780 / Ref. 801 179 / Ref. 800 161

OM-4405 Page 37

8-6. Adjusting Engine Idle Speed

Engine Speed

(No Load)

1850 rpm max
(61.6 Hz)

1250 rpm
(41.6 Hz)

2

5

3

4

 Stop engine and let cool.

Engine idle speed is factory set and
normally should not require adjust­ment. After tuning engine, check
engine speed with tachometer or
frequency meter. See table for
proper n o load speed. If necessary,
adjust idle speed as follows:

Start engine and run until warm.
On CC Models, place Stick/TIG

switch in Stick position.
On CC/CV models, turn Process/

Contactor switch to Stick – Elec­trode Hot position.

1 Solenoid Bracket Screws
2 Throttle Arm
3 Idle Speed Screw
4 Throttle Stop
Loosen bracket screws and move

arm so screw touches stop. Do not
release arm. Turn idle speed screw
to obtain 550 rpm.

5 Idle Mixture Screw

1

6

7

Turn mixture screw counterclock­wise until engine falters, then turn
screw clockwise until engine runs
smoothly.

Turn idle speed screw to obtain
1250 rpm.

6 Solenoid
7 Plunger
Slide solenoid inside bracket so

plunger bottoms in solenoid. If nec­essary, shim solenoid/bracket to
prevent linkage from binding. Do
not readjust idle speed screw when
adjusting solenoid.

Tighten bracket screws. Release
throttle arm. Recheck idle speed
and readjust if necessary .

 Stop engine.

Close door.

Tools Needed:

OM-4405 Page 38

1/4 in

802 731 / Ref. 115 155-A

8-7. Adjusting Governor Sensitivity

3

2

1

 Governor sensitivity may re-

quire readjustment if weld
speed is adjusted. Weld speed
must be readjusted if sensitivity
is adjusted.

Be sure carburetor and link­ages are adjusted properly be­fore adjusting sensitivity.

Start engine. Apply and remove
load.

1 Locking Nuts
2 Sensitivity Adjustment Screw
3 Governor Spring
If engine is slow to pick up load or

rpm drops under load, adjust spring
tension as follows:

Loosen top nut and tighten bottom
nut to move screw down. Tighten
nuts.

If engine hunts with or without load,
adjust spring tension as follows:

Loosen bottom nut and tighten top
nut to move screw up. Tighten nuts.

 Stop engine.

Close door.

Tools Needed:

1/2 in

Notes

802 780 / Ref. 115 155-A

OM-4405 Page 39

8-8. Servicing Fuel And Lubrication Systems

3

1

 Stop engine and let cool.
 After servicing, start engine and

check for fuel leaks. Stop engine,
tighten connections as necessary,
and wipe up spilled fuel.

1 Oil Filter
2 Oil Drain Valve And Hose
3 Oil Fill Cap/Dipstick
4 Fuel Tank Sludge Drain Valve

To change oil and filter:

Route oi l d r a i n v a l v e a n d hose through hole
in base. See engine manual and engine

OM-4405 Page 40

2

6

5

maintenance label for oil/filter change in­formation.

To drain sludge from fuel tank:
 Beware of fire. Do not smoke and

keep sparks and flames away from
drained fuel. Dispose of drained fuel
in an environmentally-safe manner.
Do not leave unit unattended while
draining fuel tank.

 Properly lift unit and secure in a level

position. Use adequate blocks or
stands to support unit while drain­ing fuel tank.

Attach 1/ 2 I D h ose to drain valve. Put metal
container under drain, and use screwdriver

4

Tools Needed:

802 731 / Ref. 801 434

to open sludge drain valve. Close valve
when sludge has drained. Remove hose.

Close door.

To replace fuel filter:

5 Fuel Line
6 Fuel Filter
Remove clamps and filter. Install new filter

and clamps. Inspect fuel lines and replace
if cracked or worn. Wipe up any spilled fuel.

Start engine and check for leaks.

 Stop engine, tighten connections as

necessary, and wipe up spilled fuel.

Close door.

8-9. Overload Protection

 Stop engine.

 When a circuit breaker or fuse

opens, it usually indicates a
more serious problem exists.
Contact Factory Authorized
Service Agent.

1 Fuse F1
2 Fuse F2
F1 and F2 protect the stator exciter

winding from overload. If F1 opens,
weld and auxiliary power is low or
stops entirely . I f F 2 opens, weld out­put is low or stops entirely. 4 kVA/
kW auxiliary power is still available.

21

8

7

6

4

3 Circuit Breaker CB4 (Not

Shown)

4 Circuit Breaker CB5

(CC/CV Models Only)

5 Circuit Breaker CB10 (Not

Shown)
6 Circuit Breaker CB11
7 Circuit Breaker CB12
8 Circuit Breaker CB13
CB4 protects the welding arc drive

(dig) circuit. If CB4 opens, electro­de may stick to the workpiece more
frequently during low voltage (short
arc length) conditions. CB4 auto­matically resets when the fault is
corrected.

CB5 protects the 24 volt ac output
to remote receptacle RC14, and 24
volt output to field current regulator
board PC1 (CC/CV models only). If
CB5 opens, weld output and 24 volt
output to RC14 stops. On units with
optional auxiliary power plant, aux­iliary power output at receptacle
RC5 also stops if CB5 opens.

CB10 protects the engine battery
circuit. If CB10 opens, the engine
will not crank. CB10 automatically
resets when the fault is corrected.

CB11 protects the engine wiring
harness. On CC models, if CB11
opens the max OCV circuit does
not work and open circuit voltage is
variable at all times (see max OCV
note under Weld Controls in Sec­tion 5-2). If CB11 opens on CV mod­els, weld output stops (auxiliary
power is still available).

CB12 protects the field flashing cir­cuit. If CB12 opens, the generator
may not excite at start-up and weld
and auxiliary power output may not
be available.

CB13 protects the engine shut­down circuit. If CB13 opens, the en­gine cranks but does not start.

Press button to reset breaker.

802 729 / Ref. 802 789

OM-4405 Page 41

8-10. Diagnosing Causes Of Engine Fault Shutdowns

Pre-Start Diagnostic Checks

Use the front panel engine lights to
help determine the cause of an au­tomatic engine shutdown.

 Correct the cause of the shut-

down before operating the
welding generator.

 This unit does not have a bat-

tery charging fault shutdown.
The engine continues to run if
the Battery Charging Light
goes on.

Turn Engine Control Switch To Run/Idle
Position While Pressing Magnetic Shut-

down Switch.

Diagnostic Checks While Running

Normal Condition:

Oil Pressure Light On;

Battery Charging, Fuel, And Temperature Lights Off.

If Oil Pressure Light Is Off, See Factory Authorized Service Agent.

If Battery Charging Light Is On, Have Factory Authorized Service Agent

Check Alternator.

If Temperature Light Is On, Correct Cause Of Overheating

(See Engine Manual).

If Engine Is Okay, See Factory Authorized Service Agent.

If Fuel Light Is On, Check Fuel Level.

If Fault Continues, See Factory Authorized Service Agent.

20s

Start Engine (With No Load Applied).

OM-4405 Page 42

Continue Pressing Shutdown Switch

Until Engine Lights Go Off.

Engine Lights Go Off As Engine Reaches

Normal Condition:

Normal Operating Condition.

Lights That Stay On After 20 Sec. Indicate

Fault Condition.

Stop Engine And Correct Fault (See Above) If
Fault Continues, See Factory Authorized Ser-

vice Agent.

Ref. 201 841

8-11. Troubleshooting

A. Welding – CC Models

Trouble Remedy

No weld output; auxiliary power output
okay.

No weld output or auxiliary power output. Disconnect equipment from auxiliary power receptacles during start-up.

Erratic weld output. Check and tighten connections inside and outside unit.

High weld output. Check engine speed, and adjust if necessary.

Check position of Ampere Range switch.

Check position of optional polarity switch.
Place Amperage Adjust switch in Panel position, or place switch in Remote position and connect remote

control to Remote Amperage Adjust receptacle RC13 (see Sections 4-10 and 5-1).
Check and secure connections to Remote Amperage Adjust receptacle RC13 (see Section 4-10).
Check fuse F2, and replace if open (see Section 8-9). Have Factory Authorized Service Agent check inte-

grated rectifier SR2 and the rotor.
Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.

Check fuses F1 and F2, and replace if open (see Section 8-9). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, integrated rectifier SR2, and the rotor.

Reset circuit breaker CB12. Have Factory Authorized Service Agent check diode D1 (see Section 8-9).
Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.

Be sure connection to work piece is clean and tight.
Use dry, properly stored electrodes.
Remove excessive coils from weld cables.

Have Factory Authorized Service Agent check OCV control circuit.

Low weld output. Check engine speed, and adjust if necessary.

Check fuses F1 and F2, and replace if open (see Section 8-9). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, integrated rectifier SR2, and the rotor.

Electrode sticks to the workpiece more
frequently during low voltage (short arc
length) conditions.

Low open-circuit voltage. Check engine speed, and adjust if necessary.
Maximum weld output only in each

ampere range (with Stick/TIG Selection
switch in Stick position).

No remote fine amperage control. Place Amperage Adjust switch in correct position.

Circuit breaker CB4 may be open. CB4 automatically resets when the fault is corrected (see Section 8-9).
Have Factory Authorized Service Agent check transformer T1 and integrated rectifiers SR4 and SR5.

Have Factory Authorized Service Agent check control relay CR7.

Check and secure connections to Remote Amperage Adjust receptacle RC13 (see Section 4-10).
Reset circuit breaker CB11 (see Section 8-9). Have Factory Authorized Service Agent check control relay

CR7.
Repair or replace remote control device.
Have Factory Authorized Service Agent check OCV control circuit.

OM-4405 Page 43

B. Welding – CC/CV Models

Trouble Remedy

No weld output; auxiliary power output
okay.

No weld output or auxiliary power output. Disconnect equipment from auxiliary power receptacles during start-up.

Erratic weld output. Check and tighten connections inside and outside unit.

High weld output. Check position of Ampere Range switch and Voltage/Amperage Adjust control.

Place Process/Contactor switch in a Electrode Hot position, or place switch in a Remot e position and
connect remote contactor to optional Remote 14 receptacle RC14 (see Sections 4-11 and 6-1).

Check position of Ampere Range switch.
Check position of optional polarity switch.
Reset circuit breaker CB11 (see Section 8-9).
Reset circuit breaker CB5 (see Section 8-9). Check for faulty remote device connected to RC14.
Check and secure connections to Remote 14 receptacle RC14 (see Section 4-11).
Have Factory Authorized Service Agent check connector board PC6 and connections.
Check fuse F2, and replace if open (see Section 8-9). Have Factory Authorized Service Agent check

brushes and slip rings, field excitation circuit, field current regulator board PC1, and the rotor.

Check fuses F1 and F2, and replace if open (see Section 8-9). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, field current regulator board PC1, and the rotor.

Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.

Be sure connection to work piece is clean and tight.
Use dry, properly stored electrodes.
Remove excessive coils from weld cables.

Check engine speed, and adjust if necessary.
Have Factory Authorized Service Agent check field current regulator board PC1.

Voltage/Amperage control does not
work when welding in Stick mode.

Low weld output. Check engine speed, and adjust if necessary.

Electrode sticks to the workpiece more
frequently during low voltage (short arc
length) conditions.

Low open-circuit voltage. Check engine speed, and adjust if necessary.
No remote fine amperage or voltage

control.

Constant speed wire feeder does not
work.

Place Ampere Range switch in lower range. Voltage/Amperage control does not work with Ampere
Range switch in highest range.

Check fuses F1 and F2, and replace if open (see Section 8-9). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, field current regulator board PC1, and the rotor.

Circuit breaker CB4 may be open. CB4 automatically resets when the fault is corrected (see Section 8-9).
Have Factory Authorized Service Agent check transformer T1 and integrated rectifiers SR4 and SR5.

Place Voltage/Amperage Adjust switch in Remote position.

Check and secure connections to Remote 14 receptacle RC14 (see Section 4-11).
Repair or replace remote control device.
Reset circuit breaker CB5 (see Section 8-9).

Check and secure connections to Remote 14 receptacle RC14 (see Section 4-11).
Check voltage requirements of wire feeder. 115 volt output not available through Remote 14 recep-

tacle (see Section 4-11).
Repair or replace wire feeder.

Low CV weld output. Set Ampere Range switch to highest range.
Min or max CV weld output only. Check position of Voltage/Amperage Adjust control and Voltage/Amperage Adjust switch.

Repair or replace remote control device.
Have Factory Authorized Service Agent check field current regulator board PC1.

OM-4405 Page 44

C. Standard Auxiliary Power

Trouble Remedy

No auxiliary power output; weld output
okay.

No auxiliary power or weld output. Disconnect equipment from auxiliary power receptacles during start-up.

High output at auxiliary power
receptacles.

Low output at auxiliary power
receptacles.

Reset receptacle circuit breakers.

Check fuses F1 and F2, and replace if open (see Section 8-9). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, and the rotor.

Reset circuit breaker CB12. Have Factory Authorized Service Agent check diode D1 (CC models) or field
current regulator board PC1 (CC/CV models) (see Section 8-9).

Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.
Check engine speed, and adjust if necessary.

Have Factory Authorized Service Agent adjust auxiliary power field current resistor R3.
Check engine speed, and adjust if necessary.

Check fuse F1, and replace if open (see Section 8-9). Have Factory Authorized Service Agent check inte­grated rectifier SR1, resistor R3, and capacitor C9.

D. Optional Auxiliary Power Plant

Trouble Remedy

No or low output at optional auxiliary
power plant/receptacle RC5
(CC/CV models only).

Place Process/Contactor switch in Electrode Hot - Stick position (see Section 6-3).

Reset circuit breaker CB7 (see Section 7-2).
Reset circuit breaker CB5 (see Section 8-9).
Check engine weld/power speed, and adjust if necessary (see Section 8-5).
Have Factory Authorized Service Agent check brushes and slip rings, and field current regulator board

PC1.

High output at optional auxiliary power
plant/receptacle RC5 (CC/CV models
only).

Erratic output at optional auxiliary power
plant/receptacle RC5 (CC/CV models
only).

Check engine weld/power speed, and adjust if necessary (see Section 8-5).

Have Factory Authorized Service Agent check field current regulator board PC1.
Have Factory Authorized Service Agent check brushes and slip rings, and field current regulator board

PC1.

E. Engine

Trouble Remedy

Engine will not crank. Check battery, and replace if necessary.

Check battery connections and tighten if necessary.
Circuit breaker CB10 may be open. CB10 automatically resets when fault is corrected (see Section 8-9).

Have Factory Authorized Service Agent check engine wiring harness and components.
Check engine wiring harness plug connections.
Have Factory Authorized Service Agent check Engine Control switch S1.

OM-4405 Page 45

Trouble Remedy

Engine cranks but does not start. Press Magnetic Shutdown switch MS1 when starting engine.

Check fuel level.
Reset circuit breaker CB13 (see Section 8-9). Have Factory Authorized Service Agent check engine-

wiring harness and components.
Check battery and replace if necessary. Check engine charging system according to engine manual.
Have Factory Authorized Service Agent check control relay CR2, and fuel solenoid FS1.

Engine starts, but stops when Magnetic
Shutdown switch is released.

Engine hard to start in cold weather. Use starting Aid (Engine Choke control, see Section 5-1 ).

Engine suddenly stops. Check fuel, oil, and coolant levels. Automatic shutdown system stops engine if oil pressure is too low,

When starting engine, continue holding Magnetic Shutdown switch until after engine indicator lights go
out.

Check oil, and coolant levels. Automatic shutdown system stops engine if oil pressure is too low or cool­ant temperature is too high (see Sections 4-7 and 8-10).

Keep battery in good condition. Store battery in warm area off cold surface.
Use correct grade oil for cold weather (see Section 8-1).

or coolant temperature is too high (see Sections 4-7 and 8-10).
See engine manual.

Engine slowly stopped and cannot be
restarted.

Battery discharges between uses. Turn Engine Control switch off when unit is not running.

Engine idles, but does not come up to
weld speed.

Engine does not run at idle speed. CC models: place Stick/TIG Selection switch in Stick position.

Check fuel level.

Check engine air and fuel filters (see Section 8-8).
Check engine wiring harness connections.
See engine manual.

Clean top of battery with baking soda and water solution; rinse with clear water.
Recharge or replace battery if necessary.
Periodically recharge battery (approximately every 3 months).
Have Factory Authorized Service Agent check idle module PC7, current transformer CT1, and throttle

solenoid TS1.
Check for obstructed throttle solenoid and linkage.

CC/CV models: place Process/Contactor switch in any position but Remote-TIG.
Check for obstructed throttle solenoid and linkage.

Have Factory Authorized Service Agent check idle module PC7, and control relays CR3 and CR6.

OM-4405 Page 46

Notes

OM-4405 Page 47

SECTION 9 – ELECTRICAL DIAGRAMS

OM-4405 Page 48

Figure 9-1. Circuit Diagram For CC Welding Generator

OM-4405 Page 49

201 991-A

OM-4405 Page 50

Figure 9-2. Circuit Diagram For CC/CV Welding Generator

201 992-A

OM-4405 Page 51

SECTION 10 – AUXILIARY POWER GUIDELINES

10-1. Selecting Equipment

1

1 Auxiliary Power Receptacles

– Neutral Bonded To Frame

2 3-Prong Plug From Case

Grounded Equipment

3 2-Prong Plug From Double

Insulated Equipment

2

3

OR

10-2. Grounding Generator To Truck Or Trailer Frame

1

3 4

GND/PE

Be sure equipment
has this symbol
and/or wording.

aux_pwr 2/99 – Ref. ST-159 730 / ST-800 577

1 Generator Base
2 Metal Vehicle Frame
3 Equipment Grounding

Terminal
4 Grounding Cable
Use #10 AWG or larger insulated

copper wire.

 If unit does not have GFCI re-

ceptacles, use GFCI-pro-

tected extension cord.

OM-4405 Page 52

OR

Electrically bond generator

2

frame to vehicle frame by
metal-to-metal contact.

2

S-0854

10-3. Grounding When Supplying Building Systems

1 2

GND/PE

2

3

1 Equipment Grounding

Terminal
2 Grounding Cable
Use #10 AWG or larger insulated

copper wire.
3 Ground Device

 Ground generator to system

earth ground if supplying

power to a premises (home,

shop, farm) wiring system.

Use ground device as stated
in electrical codes.

10-4. How Much Power Does Equipment Require?

3

2

1

3

AMPERES x VOLTS = WATTS

EXAMPLE 1 : If a drill uses 4.5 amperes at 115 volts, calculate its running power

requirement in watts.

4.5 A x 115 V = 520 W

The load applied by the drill is 520 watts.

VOLTS 115
AMPS
Hz

4.5
60

ST-800 576-B

1 Resistive Load
A light bulb is a resistive load and

requires a constant amount of pow­er.

2 Non-Resistive Load
Equipment with a motor is a non-re-

sistive load and requires approxi­mately six times more power while
starting the motor than when run­ning (see Section 10-8).

3 Rating Data
Rating shows volts and amperes,

or watts required to run equipment.

EXAMPLE 2 : If three 200 watt flood lamps are used with the drill from Example 1,
add the individual loads to calculate total load.

(200 W + 200 W + 200 W) + 520 W = 1120 W

The total load applied by the three flood lamps and drill is 1120 watts.

S-0623

OM-4405 Page 53

10-5. Approximate Power Requirements For Industrial Motors

Industrial Motors Rating Starting Watts Running Watts

Split Phase 1/8 HP 800 300

1/6 HP 1225 500
1/4 HP 1600 600
1/3 HP 2100 700
1/2 HP 3175 875

Capacitor Start-Induction Run 1/3 HP 2020 720

1/2 HP 3075 975
3/4 HP 4500 1400

1 HP 6100 1600

1-1/2 HP 8200 2200

2 HP 10550 2850
3 HP 15900 3900
5 HP 23300 6800

Capacitor Start-Capacitor Run 1-1/2 HP 8100 2000

5 HP 23300 6000

7-1/2 HP 35000 8000

10 HP 46700 10700

Fan Duty 1/8 HP 1000 400

1/6 HP 1400 550
1/4 HP 1850 650
1/3 HP 2400 800
1/2 HP 3500 1100

10-6. Approximate Power Requirements For Farm/Home Equipment

Farm/Home Equipment Rating Starting Watts Running Watts

Stock Tank De-Icer 1000 1000
Grain Cleaner 1/4 HP 1650 650
Portable Conveyor 1/2 HP 3400 1000
Grain Elevator 3/4 HP 4400 1400
Milk Cooler 2900 1100
Milker (Vacuum Pump) 2 HP 10500 2800
FARM DUTY MOTORS 1/3 HP 1720 720
Std. (e.g. Conveyors, 1/2 HP 2575 975
Feed Augers, Air 3/4 HP 4500 1400
Compressors) 1 HP 6100 1600

1-1/2 HP 8200 2200

2 HP 10550 2850
3 HP 15900 3900

5 HP 23300 6800
High Torque (e.g. Barn 1-1/2 HP 8100 2000
Cleaners, Silo Unloaders, 5 HP 23300 6000
Silo Hoists, Bunk Feeders) 7-1/2 HP 35000 8000

10 HP 46700 10700
3-1/2 cu. ft. Mixer 1/2 HP 3300 1000
High Pressure 1.8 Gal/Min 500 PSI 3150 950
Washer 2 gal/min 550 PSI 4500 1400
2 gal/min 700 PSI 6100 1600
Refrigerator or Freezer 3100 800
Shallow Well Pump 1/3 HP 2150 750

1/2 HP 3100 1000

Sump Pump 1/3 HP 2100 800

1/2 HP 3200 1050

OM-4405 Page 54

10-7. Approximate Power Requirements For Contractor Equipment

Contractor Rating Starting Watts Running Watts

Hand Drill 1/4 in 350 350

3/8 in 400 400
1/2 in 600 600

Circular Saw 6-1/2 in 500 500

7-1/4 in 900 900
8-1/4 in 1400 1400

Table Saw 9 in 4500 1500

10 in 6300 1800
Band Saw 14 in 2500 1100
Bench Grinder 6 in 1720 720

8 in 3900 1400

10 in 5200 1600
Air Compressor 1/2 HP 3000 1000

1 HP 6000 1500

1-1/2 HP 8200 2200

2 HP 10500 2800

Electric Chain Saw 1-1/2 HP, 12 in 1100 1100

2 HP, 14 in 1100 1100

Electric Trimmer Standard 9 in 350 350

Heavy Duty 12 in 500 500
Electric Cultivator 1/3 HP 2100 700
Elec. Hedge Trimmer 18 in 400 400
Flood Lights HID 125 100

Metal Halide 313 250

Mercury 1000

Sodium 1400

Vapor 1250 1000
Submersible Pump 400 gph 600 200
Centrifugal Pump 900 gph 900 500
Floor Polisher 3/4 HP, 16 in 4500 1400

1 HP, 20 in 6100 1600

High Pressure Washer 1/2 HP 3150 950

3/4 HP 4500 1400

1 HP 6100 1600
55 gal Drum Mixer 1/4 HP 1900 700
Wet & Dry Vac 1.7 HP 900 900

2-1/2 HP 1300 1300

OM-4405 Page 55

10-8. Power Required To Start Motor

4
1
3

Single-Phase Induction Motor Starting Requirements

Motor Start

Code GHJKLMNP

KVA/HP 6.3 7.1 8.0 9.0 10.0 11.2 12.5 14.0

kVA/HP x HP x 1000

VOLTS

EXAMPLE: Calculate the starting amperage required for a 230 V, 1/4

HP motor with a motor start code of M.

Volts = 230 HP = 1/4 Using Table, Code M results in kVA/HP = 11.2

11.2 x 1/4 x 1000
230

= 12.2 A

VOLTS AMPS
CODE 60
HP

Starting the motor requires 12.2 amperes.

AC MOTOR

230 2.5

M

1/4

= STARTING AMPERAGE

Hz
PHASE

1

2

1 Motor Start Code
2 Running Amperage
3 Motor HP
4 Motor Voltage
To find starting amperage:

Step 1: Find code and use table to
find kVA/HP. If code is not listed,
multiply running amperage by six to
find starting amperage.

Step 2: Find Motor HP and Volts.
Step 3: Determine starting amper-

age (see example).
Welding generator amperage out-

put must be at least twice the
motor’s running amperage.

S-0624

10-9. How Much Power Can Generator Supply?

1

2

1 Limit Load To 90% Of

Generator Output

Always start non-resistive (motor)
loads in order from largest to small­est, and add resistive loads last.

2 5 Second Rule
If motor does not start within 5

seconds, turn off power to prevent
motor damage. Motor requires
more power than generator can
supply.

OM-4405 Page 56

Ref. ST-800 396-A / S-0625

10-10.Typical Connections To Supply Standby Power

 Customer-supplied equipment is required if

generator is to supply standby power during
emergencies or power outages.

1

120/240 Volt

60 Hz

Three-Wire

Service

2

Load

240 V

120 V

120 V

Neutral

240 V

120 V

120 V

1 Power Company Service

Meter

2 Main and Branch Overcurrent

Protection

3 Double-Pole, Double-Throw

Transfer Switch

Obtain and install correct switch.
Switch rating must be same as or
greater than the branch overcurrent
protection.

4 Circuit Breakers or Fused

Disconnect Switch
Obtain and install correct switch.
5 Extension Cord
Select as shown in Section 10-11.
6 Generator Connections
Connect terminals or plug of ade-

quate amperage capacity to cord.
Follow all applicable codes and

3

safety practices.
Turn off or unplug all equipment

connected to generator before
starting or stopping engine. When
starting o r s t o p p i n g , t h e e ngine has
low speed which causes low volt­age and frequency.

7 Load Connections

7

120/240 Volt

Single-Phase

Three-Wire

Generator Output

Connection

4

CB

or

F1

6

240 V

120 V

120 V

Ground

Item 4 is not necessary if circuit
protection is already present in
welding generator auxiliary
power output circuit.

5

S-0405-A

OM-4405 Page 57

10-11.Selecting Extension Cord (Use Shortest Cord Possible)

Cord Lengths for 120 Volt Loads
 If unit does not have GFCI receptacles, use GFCI-protected extension cord.

Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*

Current

(Amperes)

5 600 350 (106) 225 (68) 137 (42) 100 (30)

7 840 400 (122) 250 (76) 150 (46) 100 (30) 62 (19)
10 1200 400 (122) 275 (84) 175 (53) 112 (34) 62 (19) 50 (15)
15 1800 300 (91) 175 (53) 112 (34) 75 (23) 37 (11) 30 (9)
20 2400 225 (68) 137 (42) 87 (26) 50 (15) 30 (9)
25 3000 175 (53) 112 (34) 62 (19) 37 (11)
30 3600 150 (46) 87 (26) 50 (15) 37 (11)
35 4200 125 (38) 75 (23) 50 (15)
40 4800 112 (34) 62 (19) 37 (1 1)
45 5400 100 (30) 62 (19)
50 6000 87 (26) 50 (15)

*Conductor size is based on maximum 2% voltage drop

Cord Lengths for 240 Volt Loads
 If unit does not have GFCI receptacles, use GFCI-protected extension cord.

Load (Watts) 4 6 8 10 12 14

Current

(Amperes)

5 1200 700 (213) 450 (137) 225 (84) 200 (61)

7 1680 800 (244) 500 (152) 300 (91) 200 (61) 125 (38)
10 2400 800 (244) 550 (168) 350 (107) 225 (69) 125 (38) 100 (31)
15 3600 600 (183) 350 (107) 225 (69) 150 (46) 75 (23) 60 (18)
20 4800 450 (137) 275 (84) 175 (53) 100 (31) 60 (18)
25 6000 350 (107) 225 (69) 125 (38) 75 (23)
30 7000 300 (91) 175 (53) 100 (31) 75 (23)
35 8400 250 (76) 150 (46) 100 (31)
40 9600 225 (69) 125 (38) 75 (23)
45 10,800 200 (61) 125 (38)
50 12,000 175 (53) 100 (31)

*Conductor size is based on maximum 2% voltage drop

Load (Watts) 4 6 8 10 12 14

Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*

OM-4405 Page 58

Notes

OM-4405 Page 59

 Hardware is common and

not available unless listed.

SECTION 11 – PARTS LIST

15

107

3

101

13

12

4

5 6

8

7

100 (Fig. 11–7)

11

9

2

1

106

14

12

10

99

16

17

19

18

21

22

20

93

23

24

25

105

104 (FIG. 11–4 OR 11–5)

OM-4405 Page 60

103

102

98 (FIG. 11–2 OR 11–3)

97

96 (CC ONLY)

Figure 11-1. Main Assembly

46

92

94

95

32

55

58

57

26

27

28

36

31

30

29

47

91 (SEE FIG. 11–6)

90

39

37

38

48

89

40

35

41

88

42

50

87

34

86

33

85

49

84

52

77
78
79

80
81
82

83

76

64

51

66

65

75

53

67

68

54

69

63

70

71

56

59

61

60

62

108

72

46

45

43

44

74

73

802 789

OM-4405 Page 61

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-1. Main Assembly

1 189 824 PANEL, gen LH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 191 623 LABEL, warning all panels must be in place while running 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 +189 828 PANEL, engine side 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C

4Z1
4Z1

202 151 REACTOR, ac 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C

C

201 514 REACTOR, ac 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

V

5 1T 038 621 BLOCK, term 30A 4 pole frict term str 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

038 620 LINK, jumper term blk 30A 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 081 499 BRACKET, mtg strip terminal 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 201 701 BRACE, front to center upright 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 SR4, SR5 035 704 RECTIFIER, integ bridge 40. amp 800v 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 CB4 045 061 CIRCUIT BREAKER, auto reset 24vdc 7 amp 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 201 697 PAN, reactor and rectifier 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 T1 201 613 TRANSFORMER w/bracket 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 173 352 EXTRUSION, rubber clamp/bulb (order by ft) 3ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 189 708 FIREWALL, top 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 191 307 COVER, plate 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 200 968 HOSE, elbow air cleaner 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 010 863 CLAMP, hose 1.125 – 3.000 clp dia 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 189 763 BRACKET, mtg air cleaner 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 189 764 AIR CLEANER, intake 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*192 938 FILTER, air element primary 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*♦192 939 FILTER, air element safety 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 198 457 TUBE, air intake 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 200 969 HOSE, air cleaner 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 189 464 SEAL, weather lift eye 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

173 909 HOSE, sae .312 id x .560 od x 24.000 (order by ft) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22 201 658 UPRIGHT, center assembly 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 +200 999 BASE 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 196 220 BRACKET, hold down fuel tank rear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 192 362 BRACKET, mtg nyl 1/2 conduit 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 +200 995 COVER, top 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 189 052 GROMMET, plastic neck filler fuel 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28 190 198 CAP, tank screw-on 3.500 in w/vent 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29 192 042 LABEL, use gasoline fuel only 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 108 487 LABEL, warning falling equipment 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31 010 875 CLAMP, muffler 2.000 dia 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32 105 740 PIPE, muffler exhaust engine 1.925 inlet/outlet 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33 201 851 COVER, radiator access 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34 176 230 LABEL, warning hot exhaust 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35 191 354 SUPPORT, cover 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36 189 245 TANK, fuel 23gal (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37 124 253 BUSHING, tank fuel 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

084 173 CLAMP, hose .460 – .545clp dia slfttng 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38 189 912 FITTING, stl barbed elbow w/.047 in orf zinc pld 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39 189 909 FITTING, stand pipe hose .250 x 9.260 lg 90deg zinc 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40 201 025 CAP, fuel fitting 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

41 189 913 FITTING, stl barbed elbow zinc pld 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42 190 142 SENDER, fuel gauge 9.7500 deep tank 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43 189 910 FITTING, stand pipe hose .3125 x 9.260 lg 90deg zinc 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44 189 908 VALVE, drain fuel 180deg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

45 181 572 BUSHING, tank fuel 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

46 191 446 EXTRUSION, rubber w/adhesive 1.000 x 1.000 D (order by ft) 6ft. . . . . . . . . . . . . . . . . . . . . . . . . .

47 013 367 LABEL, warning moving parts 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

48 200 984 ENGINE, Wis-Con gasoline TM-20 (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*025 474 SWITCH, thermo temp 240 make 230 open 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*025 473 SWITCH, pressure oil 8 psi brake or make 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201 141 FTG, adapter oil drain 1/2-20 male x 3/8 npt female 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*201 142 BELT, fan 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Quantity

OM-4405 Page 62

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-1. Main Assembly (Continued)

172 725 BOOT, starter eyelet terminal 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*114 559 FILTER, oil 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

49 *066 113 FILTER, inline 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

50 200 966 HOSE, radiator upper Wis-Con TM-20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51 +202 052 GUARD, fan (left side) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

52 147 923 LABEL, warning moving parts 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

53 201 982 RADIATOR, w/shroud and 7lb cap 3 row core 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

605 982 CAP, radiator pressure 7 lb 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

54 201 749 UPRIGHT, rear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

55 190 206 CABLE, bat neg 42 in lg No. 2 awg w/clamp and .375rng 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

56 108 081 TERMINAL PROTECTOR, battery post mtg 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

57 190 207 CABLE, bat pos 45 in lg No. 1 awg w/clamp and .406rng 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

58 203 430 BRACKET, battery holddown 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

59 190 897 BATTERY, stor 12V 650crk 110rsv gp 24 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

60 201 006 BOLT, j stl .312–18 x 8.500 pld 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61 +201 183 COVER, battery access 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62 168 385 LABEL, warning battery explosion can blind 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63 201 996 LABEL, warning do not operate with guard missing 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64 200 967 HOSE, radiator lower Wis-Con TM-20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

65 +200 990 GUARD, fan (right side) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

66 190 992 KEEPER, latch engine access door 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

67 190 076 CHANNEL, stiffener engine access 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

68 199 592 LATCH, paddle series 20 (black) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

69 201 031 LABEL, gasoline engine maintenance Wis-Con TM-20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

70 +200 989 DOOR, engine access 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

71 189 975 HINGE, door access 180deg 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

72 190 190 TANK, coolant recovery 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

73 201 591 STOP, door 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

74 189 826 PANEL, rocker 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

75 191 626 BUMPER, door engine access 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

76 189 827 PANEL, gen RH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

77 199 849 SCREW, 625-11 x 4.00hexhd pln gr 5 pld 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

78 071 731 WASHER, flat .656 ID x 2.250 OD x .187T stl pld 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

79 200 985 BRACKET, mtg engine Wis-Con TM-20 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80 071 890 RETAINER, mount eng/gen 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

81 071 730 TUBING, stl .875 OD x 12ga wall x 2.500 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

82 083 476 MOUNT, eng/gen nprn .875 ID x 2.500 OD x 2.000 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

83 135 205 NUT, 625-11 .94hex .76H stl pld elastic stop nut 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84 190757 SOLENOID ASSY (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

113658 LINKAGE, throttle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

115857 BRACKET, mtg solenoid idle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

005373 SOLENOID, 14vdc .84 amp pull type cont 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

010837 PIN, spring cs .093 x .625 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

199 505 HOSE, oil drain assy 32 in (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85 165 271 VALVE, oil drain 3/8-18NPTF 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86 176 529 FITTING, hose brs barbed fem 1/2tbg x 3/8NPT 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87 113 854 HOSE, SAE .500 ID x .780 OD xc oil (order by ft) 3ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

88 197 448 FITTING, hose brs barbed elbow m 1/2 tbg x 3/8 npt 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

89 201 141 FITTING, engine adapter oil drain 12-20 x 3/8 npt female 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

90 201 362 WASHER, oil drain 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

91 Figure 11-6 GENERATOR 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

92 191 897 BRACKET, mtg unit 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

93 191 512 BRACKET, hold down fuel tank 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

94 190 250 LABEL, warning do not weld on base 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

95 190 179 PANEL, mtg components 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C

96 R2

189 699 RESISTOR, WW tap 375W 10 ohm w/mtg bkt 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C

97 R3 189 699 RESISTOR, WW tap 375W 10 ohm w/mtg bkt 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

98 Figure 11-2, Figure 11-3 CONTROL BOX ASSEMBLY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Quantity

OM-4405 Page 63

Item

No.

Dia.

Mkgs.

Part

No.

Description

Quantity

Figure 11-1. Main Assembly (Continued)

99 189 731 FIREWALL, lower 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100 Figure 11-7 MAIN RECTIFIER ASSEMBLY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

101 191 448 TOP, cover front upright 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

102 +201 750 UPRIGHT, front 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

103 182 761 LABEL, warning general precautionary 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

104

Figure 11-4, Figure 11-5 PANEL, front w/components 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

105 202130 XFMR, current sensing 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

106
107 PC1

C

193 453 BRACKET, mtg box fcr 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

V

C

189 143 MODULE, field current regulator 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

V

108 +147 923 LABEL, warning moving parts can cause serious injury 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

190 058 NUT, .250-20 u-nut multi-thread 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

049 525 NUT, 312-18 u-nut multi-thread 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

202 022 KIT, label (includes safety and informational labels) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+ When ordering a component originally displaying a precautionary label, the label should also be ordered. Order

label individually or as part of Label Kit 202 022.

*Recommended Spare Parts.

C

CC models only.

C

C

CC/CV models only.

V

♦Optional

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested Replacement
Parts. Model and serial number required when ordering parts from your local distributor.

14

6

3

7

2

1

11

4

18

17

8

10

20

9

15

16

13

12

OM-4405 Page 64

19

5

Figure 11-2. Control Box Assembly – CC Models

802 551-A

Item

No.

Dia.

Mkgs.

Part

No.

Description

Quantity

Figure 11-2. Control Box Assembly – CC Models (Figure 11-1 Item 98)

1 F1, F2 *085 874 FUSE, mintr cer slo-blo 10A 250V 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 046 432 HOLDER, fuse mintr .250 x 1.250 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 201 077 CONTROL BOX, lh 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 201 078 CONTROL BOX, rh 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 201 079 COVER, control box 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 C12 191 944 CAPACITOR, polyp met film 10. uf 250 vac 10% 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201 681 HARNESS, control box, weld control (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 CR7 188 636 RELAY, OCV control 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 D1/C1 189 701 DIODE/CAPACITOR BOARD 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 SR1, SR2 035 704 RECTIFIER, integ 40A 800V 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 CR5 090 104 RELAY, encl 12VDC SPST 30A/15VDC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S5 011 609 SWITCH, tgl spdt 15a 125vac on–none–on spd term chr. . . . . . . . . . . . . . . . . . . .

(located on front panel, see Figure 11-4) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S6 011 622 SWITCH, tgl 3pdt 15a 125vac on–none–on spd term. . . . . . . . . . . . . . . . . . . .

(located on front panel, see Figure 11-4 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RC4 047 483 CONNECTOR, rect univ 084 15P/S 3 row rcpt cable/panel lkg 1. . . . . . . . . . . . . . . . . . . . . . . .

RC3 158 466 CONNECTOR, rect univ 084 12P/S 3 row rcpt cable/panel lkg 1. . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . .

RC1 135 133 CONNECTOR, rect univ 084 9P/S 3 row rcpt cable/panel lkg 1. . . .

148 850 SOCKET, relay 5 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

177 859 CONN, body 5 terminal (to engine control switch S1) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

150 316 CONN, rect univ 039 6p/s 3row plug cable lkg 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

092 670 CONN, rect univ 084 3p/s 1row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 CB11, 12, 13 139 266 CIRCUIT BREAKER, man reset 1P 15A 250VAC frict 3. . . . . . . . . . . . . . . . . . . . .

190 260 HARNESS, unit weld control (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG3 158465 CONN, rect univ 084 12p/s 3row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

187654 SEAL, wire univ 12p/s 3row 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG6 114063 CONN, rect univ 084 4p/s 1row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

192309 CLIP, snap in .630 bundle .250 hole .248 thk 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 177 136 CLAMP, capacitor 1.375dia 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 C9 087 110 CAPACITOR, elctlt 240uf 200VDC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 R6 141 424 RESISTOR, ww fxd 30 w 25 ohm faston te 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 PC7 195706 MODULE, pull to idle, two output, 7 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 CR4 113247 RELAY, encl 12vdc dpdt 20a/120vac 8pin flange mtg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 CR6 090104 RELAY, encl 12vdc spst 30a/15vdc 5pin flange mtg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 CR1, CR2, CR3 090 104 RELAY, encl 12VDC SPST 30A/15VDC spin flange mtg 3. . . . . . . . . . . . . . . . . . .

201 357 HARNESS, engine control (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 D8/C8 189 701 DIODE/CAPACITOR BOARD 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 CB10 190 374 CIRCUIT BREAKER, auto reset 12VDC 40A 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

148 850 SOCKET, relay 5 pin 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG4 114 062 CONNECTOR, rect univ 084 15P/S 3 row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*Recommended Spare Parts.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-4405 Page 65

4

16

3

15

17

11

2

1

13

14

7

12

9

6

8

5

18

10

Figure 11-3. Control Box Assembly – CC/CV Models

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-3. Control Box Assembly – CC/CV Models (Figure 11-1 Item 98)

1 F1, F2 *085 874 FUSE, mintr cer slo-blo 10A 250V 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 046 432 HOLDER, fuse mintr .250 x 1.250 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 201 077 CONTROL BOX, lh 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 201 078 CONTROL BOX, rh 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 201 079 COVER, control box 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 134 201 STAND-OFF, support pc card 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 PC9 192 224 CIRCUIT CARD ASSY, display 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 C9 087 110 CAPACITOR, elctlt 240uf 200VDC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 177 136 CLAMP, capacitor 1.375dia 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201 495 HARNESS, control box, cv weld control (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 SR1 035 704 RECTIFIER, integ 40A 800V 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 CR5 090 104 RELAY, encl 12VDC SPST 30A/15VDC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RC4 047 483 CONNECTOR, rect univ 084 15P/S 3 row rcpt cable/panel lkg 1. . . . . . . . . . . . . . . . . . . . . . . .

RC3 158 466 CONNECTOR, rect univ 084 12P/S 3 row rcpt cable/panel lkg 1. . . . . . . . . . . . . . . . . . . . . . . .

RC1 135 133 CONNECTOR, rect univ 084 9P/S 3 row rcpt cable/panel lkg 1. . . . . . . . . . . . . . . . . . . . . . . . .

12 CB11, 12, 13 139 266 CIRCUIT BREAKER, man reset 1P 15A 250VAC frict 3. . . . . . . . . . . . . . . . . . . . .

148 850 SOCKET, relay 5 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S6 193 324 SWITCH, rotary 6 position gold contacts. . . . . . . . . . . . . . . . . . .

(located on front panel, see Figure 11-5) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S5 011 609 SWITCH,tgl spdt 15a 125vac on–none–on spd term chr. . . . . . . . . . . . . . . . . . . .

(located on front panel, see Figure 11-5) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

150 316 CONN, rect univ 039 6p/s 3row plug cable lkg 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

802 360

Quantity

OM-4405 Page 66

Item

No.

Dia.

Mkgs.

Part

No.

Description

Quantity

Figure 11-3. Control Box Assembly – CC/CV Models (Continued)

177 859 CONN, body 5 terminal (to engine control switch S1) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

193 183 CONN, rect cinch 18 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

196 602 PLUG, cavity 18,30 position cinch connector 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

196 603 SEAL, switch 6 position rotary .250 shaft 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

141 450 CONN, rect metrmate 10skt 1row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 PC7 195706 MODULE, pull to idle, two output, 7 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 CR4 113247 RELAY, encl 12vdc dpdt 20a/120vac 8pin flange mtg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 CR6 090104 RELAY, encl 12vdc spst 30a/15vdc 5pin flange mtg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CR1, CR2, CR3 090 104 RELAY, encl 12VDC SPST 30A/15VDC spin flange mtg 3. . . . . . . . . . . . . . . . . . .

16

201 357 HARNESS, engine control (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 D8/C8 189 701 DIODE/CAPACITOR BOARD 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 CB10 190 374 CIRCUIT BREAKER, auto reset 12VDC 40A 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

148 850 SOCKET, relay 5 pin 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG4 114 062 CONNECTOR, rect univ 084 15P/S 3 row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

185 655 SEAL, wire univ 15P/S 3 row 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

*Recommended Spare Parts.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-4405 Page 67

 Hardware is common and

not available unless listed.

4

3

38

39

40

37

1

36

35

34

2

6

12

13

14

15

33

32

31

30
29

28

18

19

20

16

17

21

5

7

8
9

10

11

22

27

26

25

24

23

Figure 11-4. Panel, Front w/Components – CC Models

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-4. Panel, Front w/Components – CC Models (Figure 11-1 Item 104)

1 201 841 PLATE SCREENED, ident control rating; when ordering this item,. . . . . . . . . . . . . . . . . .

the nameplate should also be ordered) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 NAMEPLATE, screened (order by model and serial number) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 201 580 PANEL, engine/weld control 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 S3 189 382 SWITCH, range/changeover 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

202 223 BUS BAR, idealized 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

192 558 HARNESS, range (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RC6 148 439 HOUSING, rect univ 084 4p/s 1 row rcpt 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OM-4405 Page 68

802 799

Quantity

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-4. Panel, Front w/Components – CC Models (Continued)

5 R1 188 635 RHEOSTAT, WW 300W 34 ohm 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 202 209 SPACER, nylon 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 S6 011 622 SWITCH, tgl DPDT 15A 125VAC (included in control box harness,. . . . . . . . . . . . . . .

see Figure 11-2 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 S5 011 609 SWITCH, tgl SPDT 15A 125VAC on-none-on spd term chr (included in. . . . . . . . . . . . . . .

control box harness, see Figure 11-2) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 RC13 032 897 RECEPTACLE, twlk grd 2P3W 15A 125V 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 S1 176 606 SWITCH, ignition 4posn w/o handle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 MS1 189 698 SWITCH, magnetic manual reset low current 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201 553 CLIP, circuit breaker retaining 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 CB1 201 083 CIRCUIT BREAKER, man reset 2P 20 A, 250VAC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201 109 HARNESS, auxiliary power (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 CB2 093 996 CIRCUIT BREAKER, man reset 1P 20A 250VAC frict 3. . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 GFCI1 151 981 RECEPTACLE, str dx grd 2P3W 15/20A 125V GFCI 1. . . . . . . . . . . . . . . . . . . . . . . . . . .

15 RC1 147 632 RECEPTACLE, tw lk grd 2P3W 30A 250V L6-30R 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 190 861 LABEL, warning electric shock and moving parts 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 +201 106 PANEL, aux pwr 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 083 030 STUD, brs .250–20 x 1.750 w/hex collar 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 601 836 NUT, 250–20 .50hex .19h brs 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 ♦196 073 LABEL, do not switch while welding 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 S12 ♦195 825 SWITCH, polarity 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22 201 125 PANEL, mtg terminal pwr output 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 039 046 TERMINAL, pwr output black 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

180 735 WASHER, output stud 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 181 169 SPACER, output stud 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 186 621 BOOT, generic output stud 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 ♦059 773 HANDLE, switch 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 ♦010 647 PIN, spring cs .156 x 1.250 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28 039 047 TERMINAL, pwr output red 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29 193 260 COVER, receptacle 2.250 dia lexan 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 193 258 COVER, receptacle GFCI 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31 190 323 BOOT, circuit breaker clear hex nut 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32 193 143 BOOT, magnetic shutdown switch 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33 200 993 CONTROL, push-pull 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34 119 014 LEVER, switch black 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35 PL1 191 241 LED, red 12V 4 ind lights panel mtg round 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36 FUEL 192 265 GAUGE, fuel elec switch w/o sensor 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37 HM 118 058 METER, hour 12-24VDC 2.25dia 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38 189 161 HANDLE, switch range 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39 010 647 PIN, spring CS .156 x 1.250 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40 148 723 KNOB, pointer 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

024 103 BLANK, snap–in nyl .750 mtg hole black 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Quantity

+ When ordering a component originally displaying a precautionary label, the label should also be ordered. Order

label individually or as part of Label Kit 192 505 or Label Kit 202 022.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-4405 Page 69

 Hardware is common and

not available unless listed.

1

4

3

5

2

6

7

8

9

10

53

54

55

56

52

51

50

43

49

48

47

46

45

32

44

31

33

28

34

27

30

29

26

13

14

25

15

12

16

24

11

17

18

19

20

21

22

23

35

42

41

40 39

38

36

37

Figure 11-5. Panel, Front w/Components – CC/CV Models

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-5. Panel, Front w/Components – CC/CV Models (Figure 11-1 Item 104)

1 201 579 PLATE SCREENED, ident control; when ordering this item,. . . . . . . . . . . . . . . . . .

the nameplate should also be ordered) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 NAMEPLATE, screened (order by model and serial number) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 201 580 PANEL, engine/weld control 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 S3 189 382 SWITCH, range/changeover 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

♦202223 BUS BAR, idealized 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

192 558 HARNESS, range (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

RC6 148 439 HOUSING, rect univ 084 4p/s 1 row rcpt 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OM-4405 Page 70

802 732

Quantity

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-5. Panel, Front w/Components – CC/CV Models (Continued)

5 R1 193 118 POT, cp flat 1t 2w 1k ohm linear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 S6 193 234 SWITCH, rotary 6 position gold contacts (included in control box harness,. . . . . . . . . . . . . .

see Figure 11-3) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 S5 011 609 SWITCH, tgl SPDT 15A 125VAC on-none-on spd term chr (included in. . . . . . . . . . . . . . .

control box harness, see Figure 11-3) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 202 209 SPACER, nylon 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 PC6 192 995 CIRCUIT CARD ASSY, connector/receptacle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 CB5 139 266 CIRCUIT BREAKER, man reset 1p 15a 250vac frict 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 S1 176 606 SWITCH, ignition 4posn w/o handle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 MS1 189 698 SWITCH, magnetic manual reset low current 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 CB1 201 083 CIRCUIT BREAKER, man reset 2P 20 A, 250VAC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201 553 CLIP, circuit breaker retaining 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

201 109 HARNESS, auxiliary power (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 CB2 093 996 CIRCUIT BREAKER, man reset 1P 20A 250VAC frict 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 GFCI1 151 981 RECEPTACLE, str dx grd 2P3W 15/20A 125V GFCI 1. . . . . . . . . . . . . . . . . . . . . . . . . . .

16 RC1 147 632 RECEPTACLE, tw lk grd 2P3W 30A 250V L6-30R 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 RC5 ♦182 954 RCPT, str 3P4W 50A 125/250V 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 ♦025 248 STAND-OFF, insul .250-20 x 1.2 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 ♦604 102 CONNECTOR, clamp cable 1.000 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 ♦197 527 GUARD, circuit breaker 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 ♦197 363 TERMINAL, ring tng screw clamp 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22 CB7 ♦196 780 CIRCUIT BREAKER, man reset 3p 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 +201 106 PANEL, auxiliary power 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 +♦201 107 PANEL, auxiliary power (full kVA option) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 ♦196 781 BOOT, circuit breaker 3 pole 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 ♦197 508 PLUG, protective 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 ♦077 440 BUSHING, conduit 1 in 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 601 836 NUT, 250–20 .50hex .19h brs 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28 ♦197 291 COVER, receptacle w/gasket 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29 083 030 STUD, brs .250–20 x 1.750 w/hex collar 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CT2 ♦197 433 TRANSFORMER, current sensing 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 190 861 LABEL, warning electric shock and moving parts 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 ♦197 399 LABEL, warning 3 ph auxiliary power 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31 193 260 COVER, receptacle 2.250 dia lexan 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32 193 258 COVER, receptacle GFCI 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33 190 323 BOOT, circuit breaker clear hex nut 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34 S12 ♦195 825 SWITCH, polarity 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35 201 125 PANEL, mtg terminal pwr output 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36 PC4, PC5 189 744 CIRCUIT CARD ASSEMBLY, filter hf 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37 039 046 TERMINAL, pwr output black 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

180 735 WASHER, output stud 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38 134 201 STAND-OFF, support 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39 181 169 SPACER, output stud 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40 186 621 BOOT, generic output stud 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

41 ♦059 773 HANDLE, switch 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42 ♦010 647 PIN, spring cs .156 x 1.250 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43 039 047 TERMINAL, pwr output red 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44 ♦196 073 LABEL, do not switch while welding 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

45 193 143 BOOT, magnetic shutdown switch 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

46 200 993 CONTROL, push-pull 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

47 119 014 LEVER, switch black 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

48 190 323 BOOT, circuit breaker clear hex nut 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

49 170 391 CONN, circ ms protective cap size 20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

50 PL1 191 241 LED, red 12V 4 ind lights panel mtg round 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51 FUEL 192 265 GAUGE, fuel elec switch w/o sensor 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

52 HM 118 058 METER, hour 12-24VDC 2.25dia 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Quantity

OM-4405 Page 71

Item

No.

Dia.

Mkgs.

Part

No.

Description

Quantity

Figure 11-5. Panel, Front w/Components – CC/CV Models (Continued)

53 097 922 KNOB, pointer .875 dia x .250 ID w/set screws plstc 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

54 189 161 HANDLE, switch range 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

55 010 647 PIN, spring CS .156 x 1.250 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

56 097 924 KNOB, pointer 1.625 dia x .250 ID w/set scrws plstc 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

193 158 HARNESS, unit weld control – CV (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG6 114 063 CONNECTOR, rect univ 084 4p/s 1 row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG8 193 184 CONNECTOR, rect cinch 30 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG13 147 992 CONNECTOR, rect univ 039 10p/s 2 row plug cable 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG3 158 465 CONNECTOR, rect univ 084 12p/s 3 row plug cable 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

088 731 BUSHING, snap-in nyl .375 ID x .500 mtg hole 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

135 873 CLIP, conduit convoluted 1/2 in mtg hole 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

187 654 SEAL, wire univ 12p/s 3 row 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

024 103 BLANK, snap-in nyl .750 mtg hole blk 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

120 304 BLANK, snap–in nyl .250 mtg hole black 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+ When ordering a component originally displaying a precautionary label, the label should also be ordered. Order

label individually or as part of Label Kit 202 022.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.

 Hardware is common and

not available unless listed.

17

15

11

14

13

12

10

9

8

7

6

5

3

4

2

1

31

32

33

28

34

30

29

27

28

25

26

16

24

16

21

22

23

18

19

20

802 800

OM-4405 Page 72

Figure 11-6. Generator

Item

No.

Dia.

Mkgs.

Part

No.

Description

Figure 11-6. Generator (Figure 11-1 Item 91)

1 132 053 SCREW, .375–16x1.50 hex hd–pln gr5 pld 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 183 387 WASHER, conical spring .406 ID x .875 OD pltd 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 195 911 ENDBELL, gen (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 143 220 O-RING, 2.859 ID x .139CS 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 201 099 STATOR, exciter/aux pwr 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 +201 110 STATOR, weld assembly complete 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6+♦201 089 STATOR, weld assembly complete (full kVA option) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 013 367 LABEL, warning moving parts 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 190 197 GUARD, generator wire mesh 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 172 674 SPRING, ext .240 OD x .041 wire x 3.500pld 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 039 207 BAFFLE, air 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 201 098 ROTOR, gen (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 024 617 RING, rtng ext 1.375 shaft x .050thk 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 053 390 BEARING, ball rdl sgl row 1.370 x 2.830 x .6 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 195 547 FAN, rotor gen 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 049 026 SCREW, M10-1.5 x 25hexhd pln 8.8pln 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 083 883 WASHER, lock .402 ID x 0.709 OD 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 202 301 PLATE, flex 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 605 231 SCREW, m10–1.5x 35 hex hd–pln 8.8 pld 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 194 512 WASHER, flat 1.250 od x .406id x 7ga thk stl pld 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 183 387 WASHER, cone .380idx .860odx.109t stl pld 4000lbs 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 198 631 NUT, m10 hex lock nut stl pld 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22 201 139 FLYWHEEL, engine Wis-Con TM-20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 201 140 ADAPTER, engine Wis-Con TM-20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 191 579 COVER, starter hole 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

200 991 GUARD, starter hole Wis-Con TM-20 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

191 580 COVER, starter hole 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 172 555 SCREW, M10-1.5 x 50hexhd pln 8.8pld 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 602 159 SCREW, .312–18x .75 hexwhd.66d stl pld slffmg tap–rw 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 601 950 SCREW, .312-18 x 2.00 hexhd pln gr 5pld 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28 602 211 WASHER, lock .318 ID x 0.586 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29 139 341 WASHER, exciter 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 *190 823 BRUSH, contact 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31 188 560 CLIP, spring 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32 189 142 BRUSHHOLDER ASSEMBLY, gen 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33 602 242 WASHER, flat .375IDx0.875odx.083t stl pld 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34 604 534 SCREW, .312–18x1.25 hex hd–pln gr5 pld 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

190 259 HARNESS, brush (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PLG1 135 134 CONNECTOR, rect univ 084 9P/S 3 row plug cable lkg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

187 651 SEAL, wire univ 9P/S 3 row 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Quantity

+ When ordering a component originally displaying a precautionary label, the label should also be ordered. Order

label individually or as part of Label Kit 202 022.

*Recommended Spare Parts.
♦Optional

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-4405 Page 73

 Hardware is common and

not available unless listed.

2

1

4

3

5

6

7

8

9

802 279-A

Figure 11-7. Main Rectifier Assembly

Item

No.

Dia.

Mkgs.

Part

No.

Description

Quantity

Figure 11-7. Main Rectifier Assembly (Figure 11-1 Item 100)

201 747 RECTIFIER (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 188 137 CONNECTION BOARD, rectifier AC 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 188 517 BUS BAR, connection board 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 188 135 ENCLOSURE, rectifier 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 134 201 STAND-OFF, support 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 PC3 201 449 CIRCUIT CARD ASSEMBLY, protection 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 188 136 INSULATOR, heat sink 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 188 493 HEAT SINK, rectifier al 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 D3, D5, D7 037 956 DIODE, rect 275A 300V SP 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 D2, D4, D6 037 957 DIODE, rect 275A 300V RP 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-4405 Page 74

Warranty Questions?

Call
1-800-4-A-MILLER
for your local
Miller distributor.

Y our distributor also gives
you ...

Service

Y ou always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.

Support

Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.

Effective January 1, 2000

(Equipment with a serial number preface of “LA” or newer)

This limited warranty supersedes all previous Miller warranties and is exclusive with no other

LIMITED WARRANTY – Subject to the terms and conditions
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants
to its original retail purchaser that new Miller equipment sold
after the effective date of this limited warranty is free of defects
in material and workmanship at the time it is shipped by Miller.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.

Within the warranty periods listed below, Miller will repair or
replace any warranted parts or components that fail due to
such defects in material or workmanship. Miller must be
notified in writing within thirty (30) days of such defect or
failure, at which time Miller will provide instructions on the
warranty claim procedures to be followed.

Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty
time periods. All warranty time periods start on the date that
the equipment was delivered to the original retail purchaser, or
one year after the equipment is sent to a North American
distributor or eighteen months after the equipment is sent to an
International distributor.

1. 5 Years Parts – 3 Years Labor

* Original main power rectifiers
* Inverters (input and output rectifiers only)

2. 3 Years — Parts and Labor

* Transformer/Rectifier Power Sources
* Plasma Arc Cutting Power Sources
* Semi-Automatic and Automatic Wire Feeders
* Inverter Power Supplies
* Intellitig
* Engine Driven Welding Generators

(NOTE: Engines are warranted separately by
the engine manufacturer .)

3. 1 Year — Parts and Labor

* DS-2 Wire Feeder
* Motor Driven Guns (w/exception of Spoolmate

185 & Spoolmate 250)
* Process Controllers
* Positioners and Controllers
* Automatic Motion Devices
* RFCS Foot Controls
* Induction Heating Power Sources
* Water Coolant Systems
* HF Units
* Grids
* Maxstar 140
* Spot Welders
* Load Banks
* Miller Cyclomatic Equipment
* Running Gear/Trailers
* Plasma Cutting Torches (except APT & SAF

Models)
* Field Options

(NOTE: Field options are covered under True

Blue for the remaining warranty period of the

product they are installed in, or for a minimum of

one year — whichever is greater.)

4. 6 Months — Batteries

5. 90 Days — Parts

* MIG Guns/TIG Torches
* Induction Heating Coils and Blankets

guarantees or warranties expressed or implied.

* APT, ZIPCUT & PLAZCUT Model Plasma Cutting

Torches
* Remote Controls
* Accessory Kits
* Replacement Parts (No labor)
* Spoolmate 185 & Spoolmate 250
* Canvas Covers

Miller’s True Blue Limited Warranty shall not apply to:

1. Consumable components; such as contact tips,

cutting nozzles, contactors, brushes, slip rings,
relays or parts that fail due to normal wear.

2. Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.

3. Equipment that has been modified by any party other
than Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.

MILLER PRODUCTS ARE INTENDED FOR PURCHASE
AND USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE
AND MAINTENANCE OF WELDING EQUIPMENT.

In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation bas e d u p o n a c tual use ) upon return of the goods
at customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.

TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. I N N O EVENT SHALL MILLER BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR
ANY OTHER LEGAL THEORY.

ANY EXPRESS WARRANTY NOT PROVIDED HEREIN
AND ANY IMPLIED WARRANTY, GUARANTY OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE
OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL
EQUIPMENT FURNISHED BY MILLER IS EXCLUDED AND
DISCLAIMED BY MILLER.

Some states in the U.S.A. do not allow limitations of how long
an implied warranty lasts, or the exclusion of incidental,
indirect, special or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty
provides specific legal rights, and other rights may be
available, but may vary from state to state.

In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations
and exclusions set out above may not apply. This Limited
Warranty provides specific legal rights, and other rights may
be available, but may vary from province to province.

miller_warr 7/00

Owner’s Record

Please complete and retain with your personal records.

Model Name Serial/Style Number

Purchase Date (Date which equipment was delivered to original customer.)

Distributor

Address

City

State Zip

For Service

Call 1-800-4-A-Miller or see our website at www.MillerWelds.com
to locate a DISTRIBUTOR or SERVICE AGENCY near you.

Always provide Model Name and Serial/Style Number.

Contact your Distributor for:

Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information

and Parts)
Circuit Diagrams
Welding Process Handbooks

Miller Electric Mfg. Co.

An Ill inoi s Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA

International Headquarters–USA

USA Phone: [phone] Auto-A t t ended
USA & Canada FAX: [phone]
International FAX: [phone]

European Headquarters –
United Kingdom

Phone: [phone]
FAX: [phone]

www.MillerWelds.com

Contact the Delivering Carrier for:

For assistance in filing or settling claims,
contact your distributor and/or equipment
manufacturer’s Transportation Department.

PRINTED IN USA  2001 Miller Electric Mfg. Co. 1/01

File a claim for loss or damage during
shipment.