Miller Electric Belt Hydraulic-Driven Generator User Manual
OM-4414 209 141H
2006−07
Description
Belt/Hydraulic-Driven Generator For
Welding Power Sources
Belt-Drive Generator
Hydraulic-Drive Generator
Visit our website at
www.MillerWelds.com
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Engine Hazards 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. Compressed Air Hazards 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Additional Symbols For Installation, Operation, And Maintenance 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. California Proposition 65 Warnings 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-7. Principal Safety Standards 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-8. EMF Information 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − DEFINITIONS 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symbol Definitions 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − SPECIFICATIONS 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Description 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Specifications 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3. Generator Dimensions And Weight 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4. Controller Dimensions And Weight 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5. AC Power Curve 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − MAINTENANCE AND TROUBLESHOOTING 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Maintenance Schedule 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Overload Protection 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Troubleshooting 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − ELECTRICAL DIAGRAM 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − GENERATOR POWER GUIDELINES 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − PARTS LIST 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING
rom _nd_8/03
Warning: Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Marks a special safety message.
Means “Note”; not safety related.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see the
symbol, watch out, and follow the related instructions to avoid the
hazard. The safety information given below is only a summary of
the more complete safety information found in the Safety Standards listed in Section 1-7. Read and follow all Safety Standards.
Only qualified persons should install, operate, maintain, and re-
pair this unit.
During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks or
severe burns. The electrode and work circuit is electrically
machine internal circuits are also live when power is on. In semiautomatic or
automatic wire welding, the wire, wire reel, drive roll housing, and all metal
parts touching the welding wire are electrically live. Incorrectly installed or
improperly grounded equipment is a hazard.
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats or covers
big enough to prevent any physical contact with the work or ground.
Do not use AC output in damp areas, if movement is confined, or if there is a
danger of falling.
Use AC output ONLY if required for the welding process.
If AC output is required, use remote output control if present on unit.
Additional safety precautions are required when any of the following electri-
cally hazardous conditions are present: in damp locations or while wearing
wet clothing; on metal structures such as floors, gratings, or scaffolds;
when in cramped positions such as sitting, kneeling, or lying; or when there
is a high risk of unavoidable or accidental contact with the workpiece or
ground. For these conditions, use the following equipment in order presented: 1) a semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most
situations, use of a DC, constant voltage wire welder is recommended.
And, do not work alone!
Disconnect input power or stop engine before installing or servicing this
equipment. Lockout/tagout input power according to OSHA 29 CFR
1910.147 (see Safety Standards).
Properly install and ground this equipment according to its Owner’s Manual
and national, state, and local codes.
Always verify the supply ground — check and be sure that input power cord
ground wire is properly connected to ground terminal in disconnect box or
that cord plug is connected to a properly grounded receptacle outlet.
When making input connections, attach proper grounding conductor first −
double-check connections.
Frequently inspect input power cord for damage or bare wiring — replace
cord immediately if damaged — bare wiring can kill.
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or poorly spliced cables.
Do not drape cables over your body.
If earth grounding of the workpiece is required, ground it directly with a sep-
arate cable.
Do not touch electrode if you are in contact with the work, ground, or anoth-
er electrode from a different machine.
live whenever the output is on. The input power circuit and
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
Use only well-maintained equipment. Repair or replace damaged parts at
once. Maintain unit according to manual.
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to workpiece or work-
table as near the weld as practical.
Insulate work clamp when not connected to workpiece to prevent contact
with any metal object.
Do not connect more than one electrode or work cable to any single weld
output terminal.
SIGNIFICANT DC VOLTAGE exists in inverters after stopping engine.
Stop engine on inverter and discharge input capacitors according to
instructions in Maintenance Section before touching any parts.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing these fumes
and gases can be hazardous to your health.
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use exhaust at the arc to remove welding
fumes and gases.
If ventilation is poor, use an approved air-supplied respirator.
Read the Material Safety Data Sheets (MSDSs) and the manufacturer’s
instructions for metals, consumables, coatings, cleaners, and degreasers.
Work in a confined space only if it is well ventilated, or while wearing an air-
supplied respirator. Always have a trained watchperson nearby. Welding
fumes and gases can displace air and lower the oxygen level causing injury
or death. Be sure the breathing air is safe.
Do not weld in locations near degreasing, cleaning, or spraying operations.
The heat and rays of the arc can react with vapors to form highly toxic and
irritating gases.
Do not weld on coated metals, such as galvanized, lead, or cadmium plated
steel, unless the coating is removed from the weld area, the area is well
ventilated, and if necessary, while wearing an air-supplied respirator. The
coatings and any metals containing these elements can give off toxic fumes
if welded.
BUILDUP OF GAS can injure or kill.
Shut off shielding gas supply when not in use.
Always ventilate confined spaces or use approved
air-supplied respirator.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense visible
and invisible (ultraviolet and infrared) rays that can burn eyes
and skin. Sparks fly off from the weld.
Wear a welding helmet fitted with a proper shade of filter to protect your face
and eyes from arc rays and sparks when welding or watching (see ANSI
Z49.1 and Z87.1 listed in Safety Standards).
Wear approved safety glasses with side shields under your helmet.
Use protective screens or barriers to protect others from flash and glare;
warn others not to watch the arc.
Wear protective clothing made from durable, flame-resistant material (wool
and leather) and foot protection.
OM-4414 Page 1
WELDING can cause fire or explosion.
HOT PARTS can cause severe burns.
Welding on closed containers, such as tanks, drums, or
pipes, can cause them to blow up. Sparks can fly off from the
equipment can cause fires and burns. Accidental contact of electrode to metal
objects can cause sparks, explosion, overheating, or fire. Check and be sure
the area is safe before doing any welding.
Protect yourself and others from flying sparks and hot metal.
Do not weld where flying sparks can strike flammable material.
Remove all flammables within 35 ft (10.7 m) of the welding arc. If this is not
possible, tightly cover them with approved covers.
Be alert that welding sparks and hot materials from welding can easily go
through small cracks and openings to adjacent areas.
Watch for fire, and keep a fire extinguisher nearby.
Be aware that welding on a ceiling, floor, bulkhead, or partition can cause
fire on the hidden side.
Do not weld on closed containers such as tanks, drums, or pipes, unless
they are properly prepared according to AWS F4.1 (see Safety Standards).
Connect work cable to the work as close to the welding area as practical to
prevent welding current from traveling long, possibly unknown paths and
causing electric shock and fire hazards.
Do not use welder to thaw frozen pipes.
Remove stick electrode from holder or cut off welding wire at contact tip
when not in use.
Wear oil-free protective garments such as leather gloves, heavy shirt, cuf-
fless trousers, high shoes, and a cap.
Remove any combustibles, such as a butane lighter or matches, from your
person before doing any welding.
Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B for hot
work and have a fire watcher and extinguisher nearby.
welding arc. The flying sparks, hot workpiece, and hot
FLYING METAL can injure eyes.
Welding, chipping, wire brushing, and grinding cause
sparks and flying metal. As welds cool, they can
throw off slag.
Wear approved safety glasses with side shields even
under your welding helmet.
Allow cooling period before maintaining.
Wear protective gloves and clothing when working on
a hot engine.
Do not touch hot engine parts or just-welded parts
bare-handed.
NOISE can damage hearing.
Noise from some processes or equipment can damage
hearing.
Wear approved ear protection if noise level is high.
MAGNETIC FIELDS can affect pacemakers.
Pacemaker wearers keep away.
Wearers should consult their doctor before going
near arc welding, gouging, or spot welding operations.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high pressure. If
damaged, a cylinder can explode. Since gas cylinders are
normally part of the welding process, be sure to treat them
carefully.
Protect compressed gas cylinders from excessive heat, mechanical
shocks, slag, open flames, sparks, and arcs.
Install cylinders in an upright position by securing to a stationary support or
cylinder rack to prevent falling or tipping.
Keep cylinders away from any welding or other electrical circuits.
Never drape a welding torch over a gas cylinder.
Never allow a welding electrode to touch any cylinder.
Never weld on a pressurized cylinder — explosion will result.
Use only correct shielding gas cylinders, regulators, hoses, and fittings de-
signed for the specific application; maintain them and associated parts in
good condition.
Turn face away from valve outlet when opening cylinder valve.
Keep protective cap in place over valve except when cylinder is in use or
connected for use.
Read and follow instructions on compressed gas cylinders, associated
equipment, and CGA publication P-1 listed in Safety Standards.
1-3. Engine Hazards
BATTERY EXPLOSION can BLIND.
Always wear a face shield, rubber gloves, and protec-
tive clothing when working on a battery.
Stop engine before disconnecting or connecting bat-
tery cables or servicing battery.
Do not allow tools to cause sparks when working on a battery.
Do not use welder to charge batteries or jump start vehicles.
Observe correct polarity (+ and −) on batteries.
Disconnect negative (−) cable first and connect it last.
FUEL can cause fire or explosion.
Stop engine and let it cool off before checking or add-
ing fuel.
Do not add fuel while smoking or if unit is near any
sparks or open flames.
Do not overfill tank — allow room for fuel to expand.
Do not spill fuel. If fuel is spilled, clean up before starting engine.
Dispose of rags in a fireproof container.
Always keep nozzle in contact with tank when fueling.
OM-4414 Page 2
MOVING PARTS can cause injury.
Keep away from fans, belts, and rotors.
Keep all doors, panels, covers, and guards closed
and securely in place.
Stop engine before installing or connecting unit.
Have only qualified people remove guards or covers for maintenance
and troubleshooting as necessary.
To prevent accidental starting during servicing, disconnect negative (−)
battery cable from battery.
Keep hands, hair, loose clothing, and tools away from moving parts.
Reinstall panels or guards and close doors when servicing is finished
and before starting engine.
Before working on generator, remove spark plugs or injectors to keep
engine from kicking back or starting.
Block flywheel so that it will not turn while working on generator compo-
nents.
STEAM AND HOT COOLANT can burn.
If possible, check coolant level when engine is cold to
avoid scalding.
Always check coolant level at overflow tank, if pres-
ent on unit, instead of radiator (unless told otherwise
in maintenance section or engine manual).
If the engine is warm, checking is needed, and there is no overflow tank,
follow the next two statements.
Wear safety glasses and gloves and put a rag over radiator cap.
Turn cap slightly and let pressure escape slowly before completely re-
moving cap.
BATTERY ACID can BURN SKIN and EYES.
Do not tip battery.
Replace damaged battery.
Flush eyes and skin immediately with water.
ENGINE HEAT can cause fire.
Do not locate unit on, over, or near combustible
surfaces or flammables.
Keep exhaust and exhaust pipes way from flam-
mables.
ENGINE EXHAUST GASES can kill.
Use equipment outside in open, well-ventilated ar-
eas.
If used in a closed area, vent engine exhaust outside
and away from any building air intakes.
1-4. Compressed Air Hazards
BREATHING COMPRESSED AIR can
cause serious injury or death.
Do not use compressed air for breathing.
Use only for cutting, gouging, and tools.
COMPRESSED AIR can cause injury.
Wear approved safety goggles.
Do not direct air stream toward self or others.
TRAPPED AIR PRESSURE AND WHIPPING
HOSES can cause injury.
Release air pressure from tools and system before
servicing, adding or changing attachments, or opening compressor oil drain or oil fill cap.
EXHAUST SPARKS can cause fire.
Do not let engine exhaust sparks cause fire.
Use approved engine exhaust spark arrestor in re-
quired areas — see applicable codes.
HOT METAL from air arc cutting and
gouging can cause fire or explosion.
Do not cut or gouge near flammables.
Watch for fire; keep extinguisher nearby.
HOT PARTS can cause burns and injury.
Do not touch hot compressor or air system parts.
Let system cool down before touching or servicing.
READ INSTRUCTIONS.
Read Owner’s Manual before using or servicing unit.
Stop engine and release air pressure before
servicing.
1-5. Additional Symbols For Installation, Operation, And Maintenance
FALLING UNIT can cause injury.
Use lifting eye to lift unit only, NOT running gear, gas
cylinders, trailer, or any other accessories.
Use equipment of adequate capacity to lift and
support unit.
If using lift forks to move unit, be sure forks are long
enough to extend beyond opposite side of unit.
OVERHEATING can damage motors.
Turn off or unplug equipment before starting or stop-
ping engine.
Do not let low voltage and frequency caused by low
engine speed damage electric motors.
Do not connect 50 or 60 Hertz motors to the 100 Hertz receptacle where
applicable.
FLYING SPARKS can cause injury.
Wear a face shield to protect eyes and face.
Shape tungsten electrode only on grinder with proper
guards in a safe location wearing proper face, hand,
and body protection.
Sparks can cause fires — keep flammables away.
OVERUSE can cause OVERHEATING.
Allow cooling period; follow rated duty cycle.
Reduce current or reduce duty cycle before starting
to weld again.
Do not block or filter airflow to unit.
STATIC (ESD) can damage PC boards.
Put on grounded wrist strap BEFORE handling
boards or parts.
Use proper static-proof bags and boxes to store,
move, or ship PC boards.
TILTING OF TRAILER can cause injury.
Use tongue jack or blocks to support weight.
Properly install welding generator onto trailer accord-
ing to instructions supplied with trailer.
OM-4414 Page 3
READ INSTRUCTIONS.
ARC WELDING can cause interference.
Use only genuine MILLER/Hobart replacement
parts.
Perform engine and air compressor (if applicable)
maintenance and service according to this manual
and the engine/air compressor (if applicable) manuals.
H.F. RADIATION can cause interference.
High-frequency (H.F.) can interfere with radio naviga-
tion, safety services, computers, and communications equipment.
Have only qualified persons familiar with electronic
equipment perform this installation.
The user is responsible for having a qualified electrician
promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the equipment at
once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep spark
gaps at correct setting, and use grounding and shielding to minimize the
possibility of interference.
1-6. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases which
contain chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California Health &
Safety Code Section 25249.5 et seq.)
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
Electromagnetic energy can interfere with sensitive
electronic equipment such as microprocessors,
computers, and computer-driven equipment such as
robots.
Be sure all equipment in the welding area is electro-
magnetically compatible.
To reduce possible interference, keep weld cables as short as possible,
close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic
equipment.
Be sure this welding machine is installed and grounded according to this
manual.
If interference still occurs, the user must take extra measures such as
moving the welding machine, using shielded cables, using line filters, or
shielding the work area.
For Gasoline Engines:
Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive
harm.
For Diesel Engines:
Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and
other reproductive harm.
1-7. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
(phone: 305-443-9353, website: www.aws.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126 (phone: 305-443-9353, website: www.aws.org).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269-9101 (phone: 617-770-3000, website: www.nfpa.org and www.
sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202-4102 (phone: 703-412-0900, website:
www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale Bou-
1-8. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
levard, Rexdale, Ontario, Canada M9W 1R3 (phone: 800-463-6727 or
in Toronto 416-747-4044, website: www.csa-international.org).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, from American National Standards Institute, 11
West 42nd Street, New York, NY 10036–8002 (phone: 212-642-4900,
website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (phone:
617-770-3000, website: www.nfpa.org and www. sparky.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there
are 10 Regional Offices—phone for Region 5, Chicago, is
312-353-2220, website: www.osha.gov).
To reduce magnetic fields in the workplace, use the following
procedures:
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from
operator as practical.
5. Connect work clamp to workpiece as close to the weld as
possible.
About Pacemakers:
Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.
OM-4414 Page 4
2-1. Symbol Definitions
Belt-Drive/Pull
)
Three-Phase 7.5 kVA/kW, 18 A,
3600 rpm (60 Hz)
SECTION 2 − DEFINITIONS
Circuit Breaker
Positive Negative
Time
Read Operator’s
Manual
Hours Temperature
A
Alternating Current
Amperes
(AC)
V
Volts
Output
Protective Earth
(Ground)
h
Welding Arc
(Electrode)
SECTION 3 − SPECIFICATIONS
3-1. Description
This belt or hydraulically-driven generator supplies ac power to the platform to run tools through an ac receptacle,
and also operate lights, and cutting and welding equipment. All power regulation components are located in a watertight box that is connected by cable to the generator. The generator supplies power when running at the specified
speed with the Power switch on (switch is located on platform). A 3-pole, 30 Amp circuit breaker protects the generator
from overload.
Work Connection Voltage Input
3-2. Specifications
Drive-Type Output Generator Speed
Hydraulic
ey
Single-Phase, 6 kVA/kW, 25 A, 120/240 V,
50/60 Hz
1.0 Power Factor
100% Duty Cycle
240 V, 50/60 Hz,
1.0 Power Factor
100% Duty Cycle
803 233
3000 rpm (50 Hz)
3600 rpm (60 Hz
OM-4414 Page 5
3-3. Generator Dimensions And Weight
110 lb (50 kg)
10 lb (5 kg)
Dimensions
A 20-1/2 in (521 mm)
B 9 in (229 mm)
C 13 in (330 mm)
Weight
3-4. Controller Dimensions And Weight
Dimensions
A 11-1/2 in (292 mm)
B 9-1/2 in (241 mm)
C 4-1/2 in (114 mm)
C
A
B
803 233 A belt-driven model is shown.
C
OM-4414 Page 6
Weight
A
B
803 233
Loading...