Wireless Connectivity System
Installation Manual
MMS100
MMS100 Installation Instructions
Auxiliary
Antenna
Access
(Punch Out)
PRINTER’S INSTRUCTIONS
MANUAL, INSTRUCTIONS, MMS100 - P/N: 10023523 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5X11”, TOL. +/- 0.125, SCALE: 1:1, FRONT & BACK, FOLD TO FIT BOX
NOTE: Your Mighty Mule gate operator should be installed prior to setting up the MMS100 Wireless Connectivity System.
AT THE GATE - INSTALLING THE RADIO MODULE
Prior to any assembly of the MMS100, ensure that the Mighty Mule gate operator is turned OFF and disconnected from its power source.
If required, punch out the access hole for the Auxiliary Antenna.
Align the connectors, then plug in the small radio module into the operator control board.
Guide the radio module antenna cable through the Auxiliary Antenna hold, then twist and tighten the antenna pointing upward.
WiFi ROUTER - Setting Up and Provisioning The Bridge
1. Install/locate the bridge near your wireless router.
2. Connect the Antenna and plug in the Bridge.
3. Plug in the MMS100 (only one gate operator can be connected to your Bridge).
4. To pair/connect the MMS100 to your WiFi:
a) Download the Mighty Mule App from the Apple App Store or Google Play Store.
b) Create a Mighty Mule account, then sign in.
c) Select Add Device on the home screen.
d) Select Gate from the pop-up menu, then follow the instructions in the App (or refer to the quick start guide for your specic model at
www.mightymule.com).
PAIR
RESET
Displayed Mighty Mule App images are Apple iOS. The Android app interface will be slightly different.
Establishing Communication Between the Bridge and your Mighty Mule Gate Operator
(with radio module installed)
PAIR
RESET
Bridge Module
Control Box with Control Board
NOTE: The radio module and the bridge module are paired at the factory. They will attempt to connect after the unit is provisioned.
Establishing Communication Between the Bridge and Your Mighty Mule Gate Operator
1. Communication between the Control Board (with radio module) and Bridge Module will automatically attempt to connect.
2. The LED should be ashing blue as it attempts to connect to the Gate Operator.
3. Wait approximately 5 minutes to see if your system will connect within the “Low” power level setting.
4. If the light does not turn green, the power level setting will need to be adjusted.
To Adjust the Power Level Settings:
CAUTION: Do not set the power level setting to “Medium” or “High” if your Bridge Module and the Radio Module are within 25 ft of each other.
If the Bridge Module and Radio Module (Control Box) are far enough apart that a connection does not occur after 5 minutes of powering up the unit (the
green LED on the Bridge Module does not turn solid), then the power level will need to be adjusted. The following steps will need to be taken:
NOTE: The power level will need to be adjusted on both the Control Board and the Bridge Module using the Mighty Mule App.
1. Stand next to the gate operator control box.
2. Open the control box and adjust the power level.
a. Hold down S3 for 10 Sec. A visual indication of the current power level setting will be given via
the number of lit LEDs (1 for Low, 2 for Medium and 3 for High).
b. Adjust the power level up to Medium by pressing the S2 button.
i. S2 increases the power level setting.
ii. S4 decreases the power level setting.
3. Adjust the power level for the Bridge using the Mighty Mule App.
a. Go to the app Device Details page.
b. Click on the Power Level button (should currently be indicating Low).
c. Select Medium (which needs to align with the setting that was set on the control board).
4. Stand next to your Bridge Module, then wait 5 minutes to ensure that the LED on the Bridge
Module turns solid green.
5. If the LED on the Bridge Module does not turn green after 5 minutes, repeat steps 1-4 in order
to change the power level to High.
S2
S3
S4
S2
S3
S4
Displayed Mighty Mule App images are Apple iOS. The Android app interface will be slightly different.
Loading...