Wireless Energy Monitor
Model: HA102 |
|
User Manual |
|
Table of Contents |
|
Introduction ------------------------------- |
2 |
Features ------------------------------------ |
2 |
Overview ----------------------------------- |
3 |
----Equipment Distribution |
|
--- Display Unit |
|
--- Display Information |
|
--- Transmitter and Sensor |
|
Installation -------------------------------- |
5 |
---Find Power Cable
---Replace Battery
---Linking Transmitter and Display Unit
Operating Guide -------------------------- |
5 |
---Setting Time and Date
---Advanced Parameter Setting
---View instant and total data of electricity, cost and CO2 emission
www.mie o. com
---How to View Historical Data and Chart
---Switch on/off alarm
---How to Clear Data
---To view changes of electricity consumption quickly
Notes-------------------------------------------- |
13 |
FAQS -------------------------------------------- |
14 |
Specification ---------------------------------- |
16 |
Packing List ------------------------------------ |
17 |
1
Introduction
Thank you for purchasing our Wireless Energy Monitor which is designed for both home and small office interest of use. It includes a Display unit, transmitters and sensors. After successful connection, the display unit will show you real-time information on the amount of electricity, cost and carbon emissions. The data is very helpful for you to save energy, reduce carbon emissions and cut spending! Starts use it immediately to reduce carbon emissions to protect our environment!
In order to use the Wireless Energy Monitor properly, please read this user manual carefully to operate it. And please take good care of it for future reference. We hope that this manual will enable you to understand and use our products well. If you have encountered any problems, please contact us.
www. mie o . com
Features
Displays instant and total power usage, electricity cost and CO2 emissions View hourly, daily, weekly and monthly electricity data
Historical graphical chart of electricity consumption
Time view: Clock, day, month and year High amount of electricity warning alarm Data storage capacity: 2 years
Valid for single and dual tariff Single-phase, dual-phase and threephase power compatible
Low battery indicator and backlit display Battery life: 1 year
Wireless transmission distance of 70 meters (without obstacle);
5V DC adapter input(optional) USB power supply (optional)
2
Overview
Equipment Distribution
Meter or |
|
|
|
|
|
Transmitter |
|
|
|
|
|
|
|
Switch |
0 |
0 |
0 |
0 |
0 |
0 |
Board |
|
|
|
|
|
|
Clamp sensor |
|
|
|
|
|
Display Unit |
|
|
|
|
|
|
Display unit
5 |
4 |
6 |
3 |
2 |
1 |
|
7 |
|
8 |
|
9 |
|
10 |
1--- TIME/ALARM Setting time and alarm
2--- SEARCH Searching wireless signals
3--- HISTORY/ENTER Inquiry history data and Enter confirmation
4--- BWD/- Check last data/number minus 1 5--- FWD/+ Check next data/number plus 1 6--- MODE/SET Setting modes and
parameters
7--- DC socket
8--- USB socket
9--- 3×AAA 1.5V battery
10--- Battery cover
(Front) |
(Back) |
|
ww w . mieo. com |
3 |
Display information
4 |
11 |
|
1--- Display mode: Energy/Cost/CO2 emission
2--- Receiving signal indicator
3--- low Battery indicators
4--- Alert icons activated when higher than consumption level set
5--- Accumulative ENERGY/ COST / CO2 Emission data
6--- The histogram of Energy/ Cost/ CO2 www. mieo. com
Emissions for last seven months, weeks/ days/hours.
7--- ENERGY/ COST / CO2 Emission
8--- Clock & Calendar
9--- Cost tariff rate
10--- Money currencies
11---HISTORY means historical data in view
Transmitter and Sensor
The sensor is clipped around the incoming supply cable, usually near the meter. Then plug the sensor into the transmitter unit and information will be sent wirelessly to the display unit.
LED
Indicator
|
Check button |
|
sensor |
Phase socket |
|
Transmitter |
||
|
4
Installation |
Replace batteries |
Find power cable and install sensor: most household electricity supplies use singlephase, but also some use three phases.
Clips the sensor around the insulated live cable running into the meter or switch board to the consumer unit. For threephase supplies our Wireless transmitter isrequired with extra two sensors connected to the other two phase of lines.3 sensor arenecessary.
·Remove the battery cover from the back of the transmitter or display unit.
·Insert AA batteries into the battery compartment ensuring that the polarities of batteries are correct.
·Replace the battery cover of the transmitter and display unit.
Link display unit and transmitter
Press the ‘SEARCH ’button of display unit for 2s and the ‘CHECK’ button of transmitter , the display unit will receive the signal from transmitter.
Operating Guide
Setting time and date
·Press the ‘TIME’ button and hold for 2 seconds to enter year setting. The last two digits of year flashes, Press the FWD /BWD
www. m ieo. com |
5 |
Loading...