To avoid the risk of accidents or damage to the appliance, it is
essential to read these instructions as well as the installation sheet
before it is installed and used for the first time.
en-SAM.-Nr. 11 831 660HG07-W
Contents
Warning and safety instructions ......................................................................6
Notes on the operating instructions................................................................ 16
Notes on the layout ............................................................................................. 16
This dishwasher conforms to current safety requirements.
Inappropriate use can, however, lead to personal injury and
material damage.
Please observe the installation sheet and read the operating
instructions carefully before setting up the dishwasher and using it
for the first time. They both contain important information on its
installation, safety, use and maintenance. This is to protect
yourself from injury and prevent damage to the dishwasher.
In accordance with standard IEC60335-1, Miele expressly and
strongly advises that you read and follow the instructions in the
chapter on installing the dishwasher as well as the safety
instructions and warnings.
Miele cannot be held liable for damage caused by non-compliance
with these instructions.
Keep the installation sheet and the operating instructions in a safe
place and pass them on to any future owner.
6
Warning and safety instructions
Appropriate use
This dishwasher is intended for use in domestic households and
similar working and residential environments.
This dishwasher is not intended for outdoor use.
This dishwasher is intended for use at altitudes of up to 4000m
above sea level.
This dishwasher must only be used for cleaning domestic
crockery and cutlery. All other types of use are not permitted.
The appliance can only be used by people with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge,
if they are supervised whilst using it, or have been shown how to use
it in a safe way and recognise and understand the consequences of
incorrect operation.
7
Warning and safety instructions
Safety with children
Children under 8 years of age must be kept away from the
dishwasher unless they are constantly supervised.
Children aged 8 and older may only use the dishwasher without
supervision if they have been shown how to use it in a safe manner.
Children must be able to understand and recognise the possible
dangers caused by incorrect operation.
Children must not be allowed to clean or maintain the dishwasher
unsupervised.
Children should be supervised in the vicinity of the dishwasher.
Never allow children to play with the dishwasher. There is a danger
that children might shut themselves in the dishwasher.
If the automatic door opening mechanism is active (depending on
the model), keep young children away from the area in which the
door opens. There is a danger of injury in the unlikely event of a fault
with the opening mechanism.
Danger of suffocation! Whilst playing, children may become
entangled in packaging material (such as plastic wrapping) or pull it
over their head and risk suffocation. Keep packaging material away
from children.
Keep children away from detergents. Detergents cause severe
skin burns and severe eye damage. They can cause burning in the
mouth and throat, or inhibit breathing. It is therefore important to
keep children away from the dishwasher when the door is open.
Detergent residues could still be present in the dishwasher. Seek
medical advice immediately if a child has swallowed or inhaled any
detergents.
8
Warning and safety instructions
Technical safety
Unauthorised installation, maintenance and repairs can cause
considerable danger for the user. Installation, maintenance and
repairs must only be carried out by a Miele authorised technician.
Damage to the dishwasher can compromise your safety. Before
using the dishwasher and in particular following transport, check it
for any visible damage. Never use a damaged dishwasher.
The electrical safety of this dishwasher can only be guaranteed
when correctly earthed. It is most important that this basic safety
requirement is present. If in doubt, the electrical installation should
be checked by a Miele authorised technician.
Miele cannot be held liable for the consequences of an inadequate
or lack of earthing system (e.g. electric shock).
Reliable and safe operation of this dishwasher can only be
assured if it has been connected to the mains electricity supply.
The dishwasher must only be plugged into the electricity supply
via a suitable switched socket using a fused 3-pin plug (it must not
be hard-wired). The electrical socket must be easily accessible after
the dishwasher is installed so that it can be disconnected from the
electricity supply at any time.
There must be no electrical sockets behind the dishwasher
because the building-in niche may be too small. Danger of
overheating and fire risk if the dishwasher were to be pushed up
against a plug.
The dishwasher must not be installed underneath a hob. The high
temperatures radiated by hobs could damage the dishwasher below.
For the same reason, the appliance must not be installed next to
open fires or other appliances that give off heat, such as heaters
etc., not normally found in a kitchen.
9
Warning and safety instructions
Ensure that the connection data on the dishwasher’s data plate
(fuse rating, frequency and voltage) match the mains electricity
supply. This data must correspond in order to avoid the risk of
damage to the dishwasher. Compare these before connecting the
appliance to the mains. If in any doubt, consult a qualified
electrician.
Do not connect the dishwasher to the mains supply until it has
been fully installed and any adjustment has been made to the door
springs.
The dishwasher may only be operated if the door opening
mechanism is working correctly. Otherwise there could be a risk of
danger whilst the automatic door opening mechanism (depending on
the model) is active.
To check that the door opening mechanism is working correctly:
- The door springs must be evenly adjusted on both sides. They are
correctly adjusted when the door remains stationary when left half
open (approx. 45° opening angle). It is also important that the
door cannot fall open.
- The door locking pins automatically retract when the door opens
at the end of the drying phase.
Multi-socket adapters and extension leads do not guarantee the
required safety of the appliance (fire hazard). Do not connect the
dishwasher to the mains electricity supply using a multi-socket
adapter or an extension lead.
The dishwasher must not be used in a non-stationary location
(e.g. on a ship).
Do not install the dishwasher in a room where there is a risk of
frost occurring. Frozen hoses are at risk of tearing or bursting. The
reliability of the electronic control unit may be impaired at
temperatures below freezing point.
To avoid any damage to the dishwasher, it must only be operated
when it is connected to a fully vented plumbing system.
10
Warning and safety instructions
The plastic housing of the water connection contains a solenoid
valve. The housing must not be dipped in water.
There are live wires in the water inlet hose. Do not cut the hose,
even if it is too long.
The integrated Waterproof system offers protection from water
damage, provided that the following conditions are met:
- Installation has been carried out correctly
- The dishwasher is properly maintained and parts are replaced
where this is noticeably required
- The stopcock is turned off during longer absences from the home
(e.g. whilst on holiday).
The Waterproof system will work even when the dishwasher is
switched off. However, the dishwasher must remain connected to
the electricity supply.
The water-connection pressure needs to be between 50 and
1,000kPa.
A damaged dishwasher could be dangerous. If the dishwasher
gets damaged, switch it off at the mains immediately and call your
Miele dealer.
While the appliance is under warranty, repairs should only be
undertaken by a Miele authorised technician. Otherwise the warranty
is invalidated.
We recommend replacing defective components with original
spare parts. If original Miele spare parts are installed correctly, Miele
ensures full compliance with safety requirements and the warranty
remains valid.
During installation, maintenance and repair work, the dishwasher
must be disconnected from the mains electricity supply (switch it off
and withdraw the plug from the socket).
11
Warning and safety instructions
If the connection cable is damaged it must be replaced with a
special cable of the same type (available from Miele). For safety
reasons this work must be carried out by a Miele authorised
technician only.
This dishwasher is supplied with a special lamp (depending on the
model) to cope with particular conditions (e.g. in terms of
temperature, moisture, chemical resistance, abrasion resistance and
vibration). This special lamp must only be used for the purpose for
which it is intended. It is not suitable for room lighting. Replacement
lamps may only be fitted by a Miele authorised person or by your
Miele dealer.
Correct installation
The dishwasher must be installed and connected in compliance
with the supplied installation sheet.
Be careful before and while installing the dishwasher.
Some metal parts pose a risk of injury/being cut. Wear
protective gloves.
The dishwasher must be correctly aligned horizontally to ensure
problem-free operation.
In order to ensure stability, built-under and integrated dishwashers
must only be installed under a continuous worktop that is secured to
adjacent cabinetry.
The dishwasher must only be built into a tall unit if additional
safety precautions are taken. In order to safely install the appliance
in a tall unit, please use the Tall unit installation set and observe the
installation sheet provided. Otherwise there is the danger of the unit
tipping over.
12
Warning and safety instructions
The door springs must be evenly adjusted on both sides. They are
correctly adjusted when the door remains stationary when left half
open (approx. 45° opening angle). It is also important that the door
cannot fall open.
The appliance must only be operated with properly adjusted door
springs.
If the door cannot be adjusted properly, contact your Miele dealer.
The maximum weight of the front panel that can be aligned with the
factory fitted door springs is 10–12kg (depending on model).
Correct use
Do not use solvents in the dishwasher. Risk of explosion.
Dishwasher detergents can cause burning on the skin and in the
eyes, nose, mouth and throat. Avoid contact with detergents. Do not
inhale powder detergents. Do not swallow dishwasher detergents.
Seek medical attention immediately if detergent has been swallowed
or inhaled.
Avoid leaving the dishwasher door open unnecessarily. You could
injure yourself on the open door or trip over it.
Do not sit or lean on the open door. The dishwasher could tip
over. This could injure you or damage the dishwasher.
Crockery may be very hot at the end of the programme. Allow the
dishes to cool until they are comfortable enough to handle before
unloading them.
Only use detergent and rinse aid formulated for domestic
dishwashers. Do not use washing-up liquid.
Do not use any commercial or industrial detergents. These may
cause material damage, and there is a risk of a severe explosive
chemical reaction (such as an explosive oxyhydrogen gas reaction).
Do not fill the rinse aid reservoir with powder or liquid detergent.
This will cause damage to the reservoir.
13
Warning and safety instructions
Do not fill the AutoDos (depending on model) with powder or
liquid detergent. Loose detergent will damage the AutoDos.
Do not fill the salt reservoir with powder or liquid detergent.
Detergent will damage the water softener.
Only use special coarse-grained dishwasher salt or other pure
kitchen salt for reactivation. Other salts may contain insoluble
additives that can impair the functioning of the water softener.
In dishwashers with a cutlery basket (depending on model), knives
and forks should be placed with the handles upwards in the basket
for safety reasons. Knives and forks placed with the handles
downwards pose a danger of injury. However, cutlery placed handle
down in the basket will come out cleaner and drier.
Plastic items that cannot withstand being washed in hot water,
such as disposable plastic containers or plastic cutlery, should not
be cleaned in the dishwasher. The high temperatures in the
dishwasher may cause them to melt or lose shape.
If you use the timer option (depending on model), the detergent
compartment must be dry. If it is not, wipe it until dry. The detergent
will clump together if the detergent compartment is not dry, and this
may mean that it is not fully rinsed out.
Please observe the information given in the “Technical data”
chapter regarding the capacity of the dishwasher.
Accessories and spare parts
Only use original Miele accessories. If other parts are used,
warranty, performance and, if applicable, product liability claims will
be invalidated.
Miele will guarantee to supply functional spare parts for a
minimum of 10years and up to 15years following the
discontinuation of your dishwasher.
14
Warning and safety instructions
Transport
Damage to the dishwasher can compromise your safety. Before
using the dishwasher, check it for any visible transport damage.
Never use a damaged dishwasher.
Only transport the dishwasher in an upright position so that no
water flows into the electrical controls, as this would cause faults.
If you wish to transport the dishwasher, empty it and securely
fasten all loose parts such as baskets, hoses and mains connection
cables.
15
Notes on the operating instructions
These operating instructions apply to
several different dishwasher models of
different heights.
The different dishwasher models will be
named as follows:
normal = dishwasher measuring
80.5cm high (built-in appliance) or
84.5cm high (freestanding appliance)
XXL = dishwasher measuring 84.5cm
high (built-in appliance).
Notes on the layout
Warnings
Information which is important
for safety is highlighted in a thick
framed box with a warning symbol.
This alerts you to the potential
danger of injury to people or damage
to property.
Read these warning notes carefully
and observe the procedural
instructions and codes of practice
they describe.
Notes
Additional information and
comments
Additional information and comments
are highlighted in a box framed with a
single black line.
Instructions for the user
Instructions on how to operate the
dishwasher are identified by marked
operating steps. They explain the
procedure step by step.
Operating steps are indicated by a
black square bullet point.
Example:
Select the desired setting and press
OK to confirm.
Display
Information given via the dishwasher
display appears in a special display font
to match the font on the appliance.
Example:
When the message Close the door
appears in the display....
Notes provide information of
particular importance that must be
observed.
They are highlighted in a thick
framed box.
16
The appliance is supplied with:
- Dishwasher
- Operating instructions for operating
the dishwasher
- Installation sheet for installing the
dishwasher
- Other installation accessories for
installing the dishwasher (see
installation sheet)
- Funnel for filling the dishwasher salt
- Additional printed matter and addons if required
Scope
17
Guide to the appliance
Appliance overview
a
Door locking pins
b
Top spray arm
c
3D MultiFlex cutlery tray (depending
on model)
d
Upper basket (depending on model)
e
Middle spray arm
f
Aeration valve
g
Bottom spray arm
18
h
Filter combination
i
Salt reservoir
j
Data plate
k
Rinse aid reservoir
l
Detergent compartment
m
AutoDos detergent outlet
n
AutoDos (automatic dispensing)
Control panel
AutoDos
Express
Intense
Zone
Auto
Timer
ECO
1
2
3
4
5
6
7
8
9
10
11
12
Guide to the appliance
a
On/Offsensor control
For switching the dishwasher on and
off.
b
Optical in-operation indicator light
For indicating an ongoing wash
programme when the door is closed.
c
Remote startsensor control
For activating/deactivating the
Remote start option.
IntenseZonesensor control
Increases cleaning performance in
the lower basket.
f
Expresssensor control
For reducing the programme
duration.
g
AutoDossensor control
For activating/deactivating the
AutoDos dispensing system.
h
Timersensor control
For selecting a later programme start.
i
Display
For further information, see “Guide to
the appliance” in the “Display
functions” section.
j
Backsensor control
For navigating back to the previous
menu or deleting values that have
been set previously.
k
Sensor controls
For programme selection.
For changing the values displayed.
For scrolling to other menu pages.
l
OKsensor control
To select menu options and values
displayed.
To confirm messages.
19
Guide to the appliance
Display functions
The display is used to select or set the
following:
- The programme
- The timer
- The Settings
The display can show the following:
- The stage the programme is at
- The estimated time left for the
programme to run
- The energy and water consumption
(EcoFeedback)
- Any relevant fault messages and
information
To save energy, the dishwasher
switches off after a few minutes if you
do not press any sensor controls
during this time.
Touch the sensor control to switch
the dishwasher back on.
The OKsensor control is used to
confirm a message or setting and also
to move to the next menu or another
level.
Under Further programmes/settings
the right of the display will show a scroll
bar. This offers further options. These
options can be shown using the
sensor controls.
You can alter the dishwasher’s controls
to suit changing requirements in the
Settings menu (see “Settings” chapter).
The option that is selected will have a
tick next to it.
To exit a sub-menu again use the
Backsensor control.
If you do not press any sensor controls
for several seconds, the display will
revert to the previous menu. You may
then have to enter your settings again.
20
Caring for the environment
Disposal of the packing
material
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Disposal of your old appliance
Electrical and electronic appliances
often contain valuable materials. They
also contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance. Please
do not therefore dispose of it with your
household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Miele dealer for
advice.
Ensure that it presents no danger to
children while being stored for disposal.
21
Before using for the first time
Every dishwasher is tested at the
factory. There will be residual water in
the appliance from this test. It is not
an indication that the dishwasher has
been used previously.
Opening the door
In some programmes the door
automatically opens slightly to assist
the drying process.
This function can be deactivated, if
preferred (see “Settings” chapter,
“AutoOpen” section).
Pull the handle to open the door.
Risk of scalding due to hot
water.
During operation, water in the
dishwasher may be very hot.
During operation, only open the door
with extreme caution.
Risk of injury due to door
opening automatically.
The door may open automatically at
the end of a programme.
Keep the area around the door free
of obstructions.
Closing the door
Push the baskets right in.
Raise the door upwards until the
catch engages.
Risk of crushing due to the door
closing.
When closing the door, you are at
risk of shutting your fingers in it.
Do not put your hand inside the door
as it is closing.
Open the door fully to disengage the
locking mechanism.
At the end of the programme, if the
AutoOpen function is on, the door
locking pins automatically retract.
To prevent a technical fault, do not
hold the door locking pins firmly
when they are retracting.
If the door is opened during operation
all wash functions are automatically
interrupted.
22
Before using for the first time
Miele@home
Your dishwasher is equipped with an
integrated WiFi module.
In order to use it you will need:
- A WiFi network
- The Miele app
- A Miele user account The user
account can be created via the Miele
app.
The Miele app will guide you as you
connect your dishwasher to your home
WiFi network.
Once your dishwasher is connected to
your WiFi network you can use the app,
for example, to carry out the following
activities:
- Control your dishwasher remotely
- Call up information on the operating
status of your dishwasher
- Call up information on the
programme sequence of your
dishwasher
Availability of the WiFi connection
The WiFi connection shares a frequency
range with other appliances (including
microwave ovens and remote control
toys). This can give rise to sporadic or
even complete connection failures.
Therefore, the availability of featured
functions cannot be guaranteed.
Miele@home availability
The ability to use the Miele app
depends on the availability of the
Miele@home service in your country.
The Miele@home service is not
available in every country.
For information about availability,
please visit www.miele.com.
Miele App
The Miele App is available to download
free of charge from the Apple App
Store® or from the Google Play Store™.
Connecting your dishwasher to your
WiFi network will increase energy
consumption, even when the
dishwasher is switched off.
Make sure that your WiFi network
signal strength is strong enough at
the installation site of your
dishwasher.
23
Before using for the first time
Basic settings
Switching on the dishwasher
Open the door.
Switch the dishwasher on using the
sensor control.
The welcome screen will appear when
the dishwasher is switched on and the
welcome melody will sound.
For further information about the
display functionality, see the “Display
functions” section in the “Guide to the
appliance” chapter.
Setting the language
The display will then change
automatically to the screen for setting
the language.
Select the language you want as well
as the country, if appropriate, using
the sensor controls and confirm
with OK.
For further information on setting the
language, see the “Settings” chapter
under the “Language” section.
Setting up Miele@home
The messageSet up Miele@home will
appear in the display.
To set up Miele@home now, confirm
by touching OK.
Tip: To postpone setup until later, select
the optionSkip and confirm by touching
OK.
There are two ways of connecting your
dishwasher to your WiFi network:
Select the connection method you
want and confirm your choice with
OK.
1. Connect using App
2. Connect using WPS
You will then be guided by the display
and the Miele app.
For further information on
Miele@home, see the “Settings”
chapter under the “Miele@home”
section.
A tick will appear next to the
language that has been set.
24
Before using for the first time
Setting the time of day
The time of day is set automatically if
a connection is established with the
WiFi network.
The display will then change to the
screen for setting the time of day.
The current time of day must be set
before you can use the timer option.
Use the sensor controls to enter
the hour and confirm your entry by
touching OK.
Then set the minutes and confirm
with OK.
Holding down the relevant or
sensor control will increase or
decrease the time automatically.
Setting the water hardness level
The display will change to the screen
for setting the water hardness.
- You should programme the
dishwasher to the correct water
hardness for your area.
- Your local water authority will be able
to advise you of the water hardness
level in your area.
- Where the water hardness fluctuates
e.g. between 1.8 and 2.7mmol/l (10 15 °dH - German scale) always
programme the dishwasher to the
higher value (2.7mmol/l or 15 °dH in
this example).
In the event of a fault, it will help the
service technician if you know the
hardness of your local water supply.
Therefore, please enter the water
hardness:
____________°dH or mmol/l
The dishwasher is programmed at the
factory for a water hardness level of
2.5mmol/l (14°dH – German scale).
Set the water hardness level in your
area and confirm using OK.
See the “Settings” chapter, “Water
hardness” section for more
information.
25
Before using for the first time
Activating AutoDos
The display changes to the settings
screen for AutoDos (see the “Detergent”
chapter, “Automatic dispensing/
AutoDos” section).
Even if you do not wish to use
AutoDos, you must remove the
transport locking device from the
PowerDisk compartment before
running the first programme (see the
“Detergent” chapter, “AutoDos”
section).
You can activate AutoDos.
If you do not wish to use AutoDos
(automatic dispensing), you can
manually dispense the detergent into
the detergent compartment (see the
“Detergent” chapter, “Manual detergent
dispensing” section).
Select the setting you want and
confirm with OK.
This setting applies to all programmes
and you can change it at any time using
the AutoDossensor control.
Finally, prompts will appear in the
display.
After confirming these prompts with
OK, the messages Refill salt and
Refill rinse aid may appear.
Add salt and rinse aid if necessary
(see “Before using for the first time –
Dishwasher salt” and “Rinse aid”).
Select OK to confirm the messages.
The programme selected will appear
briefly in the display and the
appropriate sensor control will be
illuminated.
Next, the estimated energy and water
consumption may be shown for the
chosen programme for several
seconds.
Then the display will show the
estimated running time for the
programme selected.
26
Before using for the first time
Dishwasher salt
In order to achieve good cleaning
results, the dishwasher needs to
operate with soft water. Hard water
results in the build-up of calcium
deposits on crockery and on the wash
cabinet walls.
Mains water with a water hardness level
higher than 0.9mmol/l (5°dH – German
scale) must be softened. This occurs
automatically in the integrated water
softener. The water softener is suitable
for a water hardness level of up to
12.6mmol/l (70°dH – German scale).
In order to maintain the functions of
the water softener, it must be
reactivated regularly. Reactivation
occurs automatically every ninth
programme sequence. At the start of
the next programme, an additional
4.4l of water is required for this
process. Energy consumption
increases by 0.015kWh and the
programme is extended by 3minutes.
The above only applies to the ECO
programme at a water hardness of
2.5mmol/l (14°dH – German scale).
For other programmes and water
hardness levels, the frequency of
reactivation will differ.
In order to be reactivated, the water
softener requires dishwasher salt.
Depending on the water hardness level
(<3.8mmol/l, or <21°dH – German
scale), dishwasher salt is not required if
combination detergents are being used
(see “Detergent – Active ingredients”).
If the water in your area is very soft
and constantly lower than 0.9mmol/l(5°dH – German scale) you do not
need to add dishwasher salt. The salt
refill indicator will automatically switch
off after the water hardness has been
set accordingly (see “Settings – Water
hardness”).
Damage to the water softener
from detergent.
Dishwasher detergent will damage
the water softener.
Do not fill the salt reservoir with
powder or liquid detergent.
Damage caused by using
unsuitable salts.
Some types of salt may contain
insoluble components which can
cause the water softener to
malfunction.
Only use special coarse-grained
dishwasher salt or other pure kitchen
salt for reactivation.
If you only ever use combination
detergent products in your
dishwasher, you can switch off both
refill reminders if you wish (see
“Settings – Refill reminders”).
Please make sure that if you stop
using combination detergents, you
refill the dishwasher salt and rinse
aid. Switch the refill reminders back
on if required.
27
Before using for the first time
Filling the salt reservoir
Before filling the salt reservoir for the
first time, you must fill it with approx.
2l of water to enable the salt to
dissolve.
Once the dishwasher has been used
once, there is always sufficient water
in the salt reservoir.
Remove the lower basket from the
wash cabinet and unscrew the salt
reservoir cap.
Danger of corrosion due to saline
solution.
Water or saline solution will run out
of the reservoir when the cap is
opened. Saline solution that runs out
can cause corrosion in the wash
cabinet and to the dishwasher load.
The salt reservoir should therefore
only be opened in order to replenish
the salt.
Fill the salt reservoir with approx. 2l
of water (first use only).
Place the funnel provided over the
salt reservoir and carefully fill with
dishwasher salt until the reservoir is
full. The salt reservoir holds up to
2kg of salt, depending on the type of
salt used.
Clean off salt residues from around
the salt reservoir opening. Next,
screw the salt reservoir cap on again
firmly.
Immediately after filling the salt
reservoir and each time you remove
the salt container cap, run the
65°CQuickPowerWash
programme with the Express
programme option selected without a
load in the dishwasher to dissolve
and remove any traces of salt from
the wash cabinet.
28
Before using for the first time
Refilling the salt
When Refill salt appears in the
display, wait until the end of the
programme and then refill the salt
reservoir.
Confirm with OK.
The salt refill indicator will go out.
Risk of corrosion due to saline
solution.
Saline solution that runs out can
cause corrosion in the wash cabinet
and to the load items.
Each time you remove the salt
reservoir cap, you must run the
65°CQuickPowerWash
programme with the Express
programme option selected without
any load items in the dishwasher.
This will dissolve and remove any
traces of salt from the wash cabinet.
After the salt reservoir has been filled,
the salt refill indicator may still appear in
the display if the salt concentration has
not yet reached the correct level. In this
case, confirm the message again with
OK.
The salt refill indicator will be switched
off if you have programmed the
dishwasher for a water hardness below
0.9mmol/l (5°dH – German scale).
29
Before using for the first time
Rinse aid
Rinse aid is necessary to ensure that
water does not cling and leave marks
on crockery during the drying phase,
and helps crockery dry faster after it
has been washed.
Rinse aid is poured into the container
and the amount set is dispensed
automatically.
Washing-up liquid or detergent
can cause damage.
Washing-up liquid and detergent can
damage the rinse aid container.
Only fill it with rinse aid formulated
for domestic dishwashers.
Alternatively, you could use liquid citric
acid at a concentration of up to 10%.
The resulting rinsing and drying quality
on the crockery will not, however, be as
good as when rinse aid is used.
Risk of acid damage.
The dishwasher can be damaged by
high concentrations of acid.
Under no circumstances should you
use citric acid with a higher acid
content.
If you only ever wish to use
combination products in your
dishwasher, you do not need to add
rinse aid.
However, for optimum rinsing and
drying results, use dishwasher
detergent and add dishwasher salt
and rinse aid separately.
If you only ever use combination
detergent products containing salt and
rinse aid in your dishwasher, you can
switch off both refill reminders if you
wish (see “Settings – Refill
reminders”).
Please make sure that if you stop
using combination detergents, you
refill the dishwasher salt and rinse
aid. Switch the refill reminders back
on if required.
30
Loading...
+ 94 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.